client_macros.cfg

# User defined macros

[include input_shaper_tuning.cfg]


[gcode_macro START_PRINT]
default_parameter_BED_TEMPERATURE: 60
default_parameter_EXTRUDER_STANDBY_TEMPERATURE: 170
default_parameter_EXTRUDER_TEMPERATURE: 210
default_parameter_CHAMBER_TEMPERATURE: 20
gcode:
  #LED_STARTING
  KINEMATICS_SAFE_DEFAULTS
  CLEAR_PAUSE
  G90 ; use absolute coordinates
  M83 ; extruder relative mode
  M106 S50 ; Fan on approx. 20% to protect cooling ducts
  M140 S{BED_TEMPERATURE} ; set bed temp
  M104 S{EXTRUDER_STANDBY_TEMPERATURE} ; set standby extruder temp
  M141 S{CHAMBER_TEMPERATURE} ; set target chamber temperature
  M190 S{BED_TEMPERATURE} ; wait for bed temp
  M106 S25 ; Part cooling fan 10% to protect ducts
  ; M109 S170 ; wait for extruder temp
  ;BED_MESH_CLEAR
  G28 ; home all
  QUAD_GANTRY_LEVEL
  G28 Z ; re-home Z because gantry levelling potentially alters the Z offset.
  move_to_purge_bucket ; while we wait for the hot end to heat up
  M104 S{EXTRUDER_TEMPERATURE} ; set first layer extruder temp
  M109 S{EXTRUDER_TEMPERATURE} ; wait for extruder temp
  CLEAN_NOZZLE ; Purge and wipe
  G28 Z ; Re-home Z after cleaning because grunge on the nozzle can throw the Z-offset off.
  CENTER
  G1 E2 ; Prime nozzle (cleaning leaves filament retracted 2mm)
  G92 E0.0
  #LED_PRINTING
  # Uncomment for input shaper tuning
  # INPUT_SHAPER_TUNING_TOWER

[gcode_macro CANCEL_PRINT]
rename_existing: BASE_CANCEL_PRINT
gcode:
  TURN_OFF_HEATERS
  CLEAR_PAUSE
  SDCARD_RESET_FILE
  SET_FAN_SPEED SPEED=0.25
  KINEMATICS_SAFE_DEFAULTS
  #LED_FAIL
  BASE_CANCEL_PRINT

[gcode_macro PAUSE]
rename_existing: BASE_PAUSE
default_parameter_E: 1.7
gcode:
  #LED_PAUSED
  {% set x_park = printer.toolhead.axis_minimum.x|float + 5.0 %}
  {% set y_park = printer.toolhead.axis_maximum.y|float - 15.0 %}
  {% set max_z = printer.toolhead.axis_maximum.z|float %}
  {% set act_z = printer.toolhead.position.z|float %}
  {% if act_z < (max_z - 40) %}
      {% set z_safe = 40 %}
  {% else %}
      {% set z_safe = max_z - act_z %}
  {% endif %}
  SAVE_GCODE_STATE NAME=PAUSE_state
  BASE_PAUSE
  G91
  G1 E-{E} F2100
  G1 Z{z_safe} F900
  G90
  G0 X{x_park} Y{y_park} F6000

[gcode_macro TURN_OFF_HEATERS]
rename_existing: BASE_TURN_OFF_HEATERS
gcode:
  M141 S35  ; Cool chamber to something approaching room temperature
  BASE_TURN_OFF_HEATERS
  
[gcode_macro RESUME]
rename_existing: BASE_RESUME
default_parameter_E: 1.7
gcode:
  #LED_PRINTING
  G91
  G1 E{E} F2100
  RESTORE_GCODE_STATE NAME=PAUSE_state
  BASE_RESUME

[gcode_macro KINEMATICS_SAFE_DEFAULTS]
gcode:
  SET_VELOCITY_LIMIT VELOCITY=400 ACCEL=9000 ACCEL_TO_DECEL=1050 SQUARE_CORNER_VELOCITY=7.5
  SET_PRESSURE_ADVANCE ADVANCE=0.04 SMOOTH_TIME=0.040

 
[gcode_macro END_PRINT]
gcode:
  #LED_SUCCESS
  KINEMATICS_SAFE_DEFAULTS
  # Move nozzle away from print while retracting
  M83 ; Relative E
  G91 ; Relative XYZ
  G1 X-2 Y-2 Z+5 E-3 F300
  G90 ; Absolute XYZ
  M82 ; Absolute E
  TURN_OFF_HEATERS
  M106 S50 ; Leave fan running to protect cooling ducts.
  PRESENT_PLATE

[gcode_macro G29]
gcode:
  QGL_HOME_AND_CENTER

[gcode_macro G32]
gcode:
  QGL_HOME_AND_CENTER

[gcode_macro QGL_HOME_AND_CENTER]
gcode:
    ;BED_MESH_CLEAR
    G28
    QUAD_GANTRY_LEVEL
    G28 Z
    CENTER

[gcode_macro CENTER]
default_parameter_FEED_RATE: 12000
gcode:
  {% set posy = printer.toolhead.axis_maximum.y|float / 2.0 %}
  {% set posx = printer.toolhead.axis_maximum.x|float / 2.0 %}
  G0 X{posx} Y{posy} F{FEED_RATE}

# Moves the print head to a position over the centre of the bed and no lower than Z=200.
# If the print is higher than 200 mm, tries to raise Z by at least 50 mm, limited by the axis maximum.
[gcode_macro PRESENT_PLATE]
default_parameter_FEED_RATE: 12000
gcode:
  {% set posy = printer.toolhead.axis_maximum.y|float / 2.0 %}
  {% set posx = printer.toolhead.axis_maximum.x|float / 2.0 %}
  {% set max_z = printer.toolhead.axis_maximum.z|float %}
  {% set min_z = 200.0 %}
  {% set toolhead_z = printer.toolhead.position.z|float %}
  {% set target_z = toolhead_z + 50 %}
  {% if target_z > max_z %}
    {% set target_z = max_z %}
  {% endif %}
  {% if target_z < min_z %}
    {% set target_z = min_z %}
  {% endif %}
  G0 X{posx} Y{posy} Z{target_z} F{FEED_RATE}

[gcode_macro LOAD_FILAMENT]
default_parameter_SPEED: 1800
default_parameter_PRIME_SPEED: 400
default_parameter_PURGE_LENGTH: 55
gcode:
  ; TODO - this may not work if changing filament in the middle of a print.
  SAVE_GCODE_STATE NAME=__filament__load
  M83
  G1 E5 F75
  G1 E50 F{SPEED}
  clean_nozzle PURGE_SPEED={PRIME_SPEED} PURGE_LENGTH={PURGE_LENGTH}
  ;G1 E35 F{PRIME_SPEED}
  ;G1 E20 F{PRIME_SPEED}
  ;G1 E-1 F{SPEED}
  RESTORE_GCODE_STATE NAME=__filament__load
  
[gcode_macro UNLOAD_FILAMENT]
default_parameter_SPEED: 1500
default_parameter_RAMMING_SPEED: 400
gcode:
  SAVE_GCODE_STATE NAME=__filament__load
  M83
  G1 E-13 F{SPEED}
  G1 E17 F{RAMMING_SPEED}
  G1 E-13 F{SPEED}
  G1 E17 F{RAMMING_SPEED}
  G1 E-13 F{SPEED}
  G1 E17 F{RAMMING_SPEED}
  G1 E-50 F{SPEED}
  G1 E-50 F{SPEED}
  RESTORE_GCODE_STATE NAME=__filament__load

[gcode_macro M600]
gcode:
  CHANGE_FILAMENT  

[gcode_macro M601]
gcode:
    CHANGE_FILAMENT

[gcode_macro CHANGE_FILAMENT]
default_parameter_RESUME_SPEED: 80
gcode:
  M117 Change Filament
  PAUSE
  M117

[gcode_macro EXERCISE_KINEMATICS]
default_parameter_SPEED: 10000
gcode:
  G28
  G0 X50 Y50 Z50 F{SPEED}
  G0 X300
  G0 Y300
  G0 X50
  G0 Y50
  G0 X300 Y300 Z300
  G0 X50
  G0 Y50
  G0 X300
  G0 Y300
  G0 X175 Y175 Z175
  G0 X50 Y50 Z50 F{SPEED}
  G0 X300
  G0 Y300
  G0 X50
  G0 Y50
  G0 X300 Y300 Z50 F6000
  M84 ; Motors off (forces re-home in case of lost steps)

[gcode_macro FRONT_RIGHT]
default_parameter_FEED_RATE: 12000
gcode:
  {% set x_park = printer.toolhead.axis_maximum.x|float - 15.0 %}
  {% set y_park = printer.toolhead.axis_minimum.y|float + 15.0 %}
  G0 X{x_park} Y{y_park} F{FEED_RATE}

[gcode_macro FRONT_CENTER]
default_parameter_FEED_RATE: 12000
gcode:
  {% set x_park = printer.toolhead.axis_maximum.x|float / 2.0 %}
  {% set y_park = printer.toolhead.axis_minimum.y|float + 15.0 %}
  G0 X{x_park} Y{y_park} F{FEED_RATE}

[gcode_macro TOP]
default_parameter_FEED_RATE: 12000
gcode:
  {% set z_park = printer.toolhead.axis_maximum.z|float - 50.0 %}
  G0 Z{z_park} F{FEED_RATE}

[gcode_macro CUBE_CENTRE]
default_parameter_FEED_RATE: 12000
gcode:
  {% set x_centre = printer.toolhead.axis_maximum.x|float / 2.0 %}
  {% set y_centre = printer.toolhead.axis_maximum.y|float / 2.0 %}
  {% set z_centre = printer.toolhead.axis_maximum.z|float / 2.0 %}
  G0 X{x_centre} Y{y_centre} Z{z_centre} F{FEED_RATE}

[gcode_macro HOME_CORNER]
default_parameter_FEED_RATE: 12000
gcode:
  {% set x_park = printer.toolhead.axis_maximum.x|float - 20.0 %}
  {% set y_park = printer.toolhead.axis_maximum.y|float - 20.0 %}
  {% set z_park = printer.toolhead.axis_minimum.z|float + 50.0 %}
  CUBE_CENTRE FEED_RATE={FEED_RATE}
  G0 X{x_park} Y{y_park} Z{z_park} F{FEED_RATE}

[gcode_macro PID_TUNE_EXTRUDER]
gcode:
  PID_CALIBRATE HEATER=extruder TARGET=250

  

SuperSlicer Start Gcode

M109 S0 ; uncomment to remove set&wait temp gcode added automatically after this start gcode
START_PRINT EXTRUDER_TEMPERATURE={first_layer_temperature[initial_extruder] + extruder_temperature_offset[initial_extruder]} BED_TEMPERATURE=[first_layer_bed_temperature] CHAMBER_TEMPERATURE=[chamber_temperature] EXTRUDER_STANDBY_TEMPERATURE={first_layer_temperature[initial_extruder] - 40}