Some configuration for Arch Linux on a Dell XPS 13 9350

20-synaptics.conf

Section "InputClass"
    Identifier "touchpad"
    Driver "synaptics"
    MatchIsTouchpad "on"
        Option "TapButton1" "1"
        Option "TapButton2" "3"
        Option "TapButton3" "2"
        Option "VertEdgeScroll" "on"
        Option "VertTwoFingerScroll" "on"
        Option "HorizEdgeScroll" "on"
        Option "HorizTwoFingerScroll" "on"
        Option "CircularScrolling" "on"
        Option "CircScrollTrigger" "2"
        Option "EmulateTwoFingerMinZ" "40"
        Option "EmulateTwoFingerMinW" "8"
        Option "CoastingSpeed" "0"
        Option "FingerLow" "35"
        Option "FingerHigh" "40"
EndSection

arch.conf

title	Arch Linux
linux	/vmlinuz-linux
initrd	/intel-ucode.img
initrd	/initramfs-linux.img
options	root=/dev/nvme0n1p3 rw i915.preliminary_hw_support=1

fstab

# /dev/nvme0n1p3
UUID=3d4a6e07-3fc0-4271-8020-ddcd60327b62         	ext4      	rw,relatime,data=ordered,discard	0 1

# /dev/nvme0n1p1
UUID=DC45-4BA2      	/boot     	vfat      	rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro,discard	0 2

# /dev/nvme0n1p2
UUID=e8911e8f-c503-404f-ba08-7e2b930d3653	none      	swap      	defaults	0 0

loader.conf

# timeout 3
default arch

mkinitcpio.conf

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run.  Advanced users may wish to specify all system modules
# in this array.  For instance:
#     MODULES="piix ide_disk reiserfs"
MODULES="intel_agp i915"

# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image.  This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way.  This is useful for config files.
FILES=""

# HOOKS
# This is the most important setting in this file.  The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added.  Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
##   This setup specifies all modules in the MODULES setting above.
##   No raid, lvm2, or encrypted root is needed.
#    HOOKS="base"
#
##   This setup will autodetect all modules for your system and should
##   work as a sane default
#    HOOKS="base udev autodetect block filesystems"
#
##   This setup will generate a 'full' image which supports most systems.
##   No autodetection is done.
#    HOOKS="base udev block filesystems"
#
##   This setup assembles a pata mdadm array with an encrypted root FS.
##   Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
#    HOOKS="base udev block mdadm encrypt filesystems"
#
##   This setup loads an lvm2 volume group on a usb device.
#    HOOKS="base udev block lvm2 filesystems"
#
##   NOTE: If you have /usr on a separate partition, you MUST include the
#    usr, fsck and shutdown hooks.
HOOKS="base udev autodetect modconf block filesystems keyboard fsck"

# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
#COMPRESSION="lz4"

# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""