C.H.I.P. u-boot printenv

C.H.I.P. u-boot printenv

=> printenv
baudrate=115200
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_targets=fel usb0 pxe dhcp
bootargs=root=ubi0:rootfs rootfstype=ubifs rw earlyprintk ubi.mtd=4
bootcmd=echo CHIP ID: chip-${serial#} ;gpio set PB2; if test -n ${fel_booted} && test -n ${scriptaddr}; then echo (FEL boot); source ${scriptaddr}; fi; mtdparts; ubi part UBI; ubifsmount ubi0:rootfs; ubifsload $fdt_addr_r /boot/sun5i-r8-chip.dtb; ubifsload $kernel_addr_r /boot/zImage; setenv bootargs $bootargs $kernelarg_video; bootz $kernel_addr_r - $fdt_addr_r
bootcmd_dhcp=usb start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi
bootcmd_fel=if test -n ${fel_booted} && test -n ${scriptaddr}; then echo '(FEL boot)'; source ${scriptaddr}; fi
bootcmd_pxe=usb start; dhcp; if pxe get; then pxe boot; fi
bootcmd_usb0=setenv devnum 0; run usb_boot
bootdelay=2
bootm_size=0xa000000
console=ttyS0,115200
dfu_alt_info_ram=kernel ram 0x42000000 0x1000000;fdt ram 0x43000000 0x100000;ramdisk ram 0x43300000 0x4000000
dip_addr_r=0x43400000
dip_overlay_cmd=if test -n "${dip_overlay_name}"; then ubifsload $dip_addr_r $dip_overlay_dir/$dip_overlay_name; fi
dip_overlay_dir=/lib/firmware/nextthingco/chip/early
distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
ethact=usb_ether
ethaddr=02:10:0a:40:bb:44
fdt_addr_r=0x43000000
fdtcontroladdr=5ab25520
fdtfile=sun5i-r8-chip.dtb
kernel_addr_r=0x42000000
mtdids=nand0=sunxi-nand.0
mtdparts=mtdparts=sunxi-nand.0:4m(spl),4m(spl-backup),4m(uboot),4m(env),-(UBI)
preboot=usb start
pxefile_addr_r=0x43200000
ramdisk_addr_r=0x43300000
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scriptaddr=0x43100000
serial#=162542100a40bb44
splashpos=m,m
stderr=serial
stdin=serial,usbkbd
stdout=serial
ubifs_boot=if ubi part UBI && ubifsmount ubi${devnum}:boot; then setenv devtype ubi; setenv bootpart 0; run scan_dev_for_boot; fi
usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi
usbnet_devaddr=de:ad:be:af:00:01
video-mode=sunxi:720x480-24@60,monitor=composite-ntsc,overscan_x=40,overscan_y=20

Environment size: 3274/4194300 bytes
=>