Skip to content

Instantly share code, notes, and snippets.

@angerman
Created December 4, 2020 09:35
Show Gist options
  • Save angerman/56a358fb00e49af9607500db6413afec to your computer and use it in GitHub Desktop.
Save angerman/56a358fb00e49af9607500db6413afec to your computer and use it in GitHub Desktop.
U-Boot 2020.07 (Jan 01 1980 - 00:00:00 +0000)
SoC: Rockchip rk3399
Reset cause: POR
DRAM: 3.9 GiB
PMIC: RK808
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
MMC: mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Helios64
Revision: 1.2 - 4GB non ECC
Net: eth0: ethernet@fe300000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:3...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
776 bytes read in 5 ms (151.4 KiB/s)
1: NixOS - Default
Retrieving file: /boot/extlinux/../nixos/7kbv6yaydlkrm6w6vxzqm22m3a1iqajx-initrd-linux-5.8.18-initrd
10170297 bytes read in 436 ms (22.2 MiB/s)
Retrieving file: /boot/extlinux/../nixos/myh6wkkv2zwhmvmj3pqp4vpl7jzgsbs3-linux-5.8.18-Image
40233472 bytes read in 1674 ms (22.9 MiB/s)
append: systemConfig=/nix/store/6rgwqbbq51isym4s3wfwpkfl1ds9ygz0-nixos-system-nixos-20.09pre-git init=/nix/store/6rgwqbbq51isym4s3wfwpkfl1ds9ygz0-nixos-system-nixos-20.09pre-git/init cma=32M console=ttyS0,115200n8 console=ttyAMA0,115200n8 console=tty0 loglevel=7
Retrieving file: /boot/extlinux/../nixos/myh6wkkv2zwhmvmj3pqp4vpl7jzgsbs3-linux-5.8.18-dtbs/rockchip/rk3399-helios64.dtb
Skipping nixos-default for failure retrieving fdt
SCRIPT FAILED: continuing...
switch to partitions #0, OK
mmc0(part 0) is current device
** No partition table - mmc 0 **
starting USB...
Bus usb@fe380000: failed to get usb phy
Port not available.
Bus usb@fe3a0000: failed to get usb phy
Port not available.
Bus dwc3: usb maximum-speed not found
Failed to get PHY0 for dwc3
Port not available.
USB is stopped. Please issue 'usb start' first.
starting USB...
Bus usb@fe380000: failed to get usb phy
Port not available.
Bus usb@fe3a0000: failed to get usb phy
Port not available.
Bus dwc3: Failed to get PHY0 for dwc3
Port not available.
Speed: 1000, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 10.0.0.119 (1018 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
missing environment variable: pxeuuid
Retrieving file: /boot/extlinux/pxelinux.cfg/01-64-62-66-d0-09-28
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A000077
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A00007
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A0000
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A000
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A00
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A0
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0A
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/0
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/default-arm-rk3399-helios64
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/default-arm-rk3399
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/default-arm
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Retrieving file: /boot/extlinux/pxelinux.cfg/default
Speed: 1000, full duplex
*** ERROR: `serverip' not set
Config file not found
starting USB...
Bus usb@fe380000: failed to get usb phy
Port not available.
Bus usb@fe3a0000: failed to get usb phy
Port not available.
Bus dwc3: Failed to get PHY0 for dwc3
Port not available.
Speed: 1000, full duplex
BOOTP broadcast 1
DHCP client bound to address 10.0.0.119 (4 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
Speed: 1000, full duplex
BOOTP broadcast 1
DHCP client bound to address 10.0.0.119 (4 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=>
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment