kernel.log

[    0.000000] Linux version 4.4.50 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-106.24
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: 96328ang
[    0.000000] MIPS: machine is NuCom R5010UN v2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 803a4530, node_mem_map 810026e0
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 59584K/65536K available (3122K kernel code, 155K rwdata, 504K rodata, 1268K init, 198K bss, 5952K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945377789 ns
[    0.000019] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421772796ns
[    0.008095] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.046775] pid_max: default: 32768 minimum: 301
[    0.051823] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.058624] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.073112] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.085970] NET: Registered protocol family 16
[    0.333028] registering PCI controller with io_map_base unset
[    0.357631] PCI host bridge to bus 0000:00
[    0.361892] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.368959] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.375943] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.382930] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.391141] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
[    0.391285] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.391765] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.400385] pci 0000:01:00.0: [14e4:a8db] type 00 class 0x028000
[    0.400505] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[    0.400700] pci 0000:01:00.0: supports D1 D2
[    0.401121] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.401171] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.401249] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.408280] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f07fff 64bit]
[    0.415816] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.420914] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.429410] clocksource: Switched to clocksource MIPS
[    0.437575] NET: Registered protocol family 2
[    0.444151] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.451442] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.458036] TCP: Hash tables configured (established 1024 bind 1024)
[    0.465047] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.471160] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.478144] NET: Registered protocol family 1
[    0.482759] PCI: CLS 0 bytes, default 16
[    0.494430] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.500849] Crashlog allocated RAM at address 0x3f00000
[    0.541962] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547978] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.564416] io scheduler noop registered
[    0.568477] io scheduler deadline registered (default)
[    0.574898] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.581727] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.591369] console [ttyS0] enabled
[    0.598522] bootconsole [early0] disabled
[    0.616838] m25p80 spi1.0: found s25fl128s, expected m25p80
[    0.622630] m25p80 spi1.0: s25fl128s (16384 Kbytes)
[    0.628267] bcm63xxpart: CFE boot tag found with version 6 and board type 96328ang
[    0.636168] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.642819] bcm63xxpart: Partition 1 is kernel offset 10100 and length 136830
[    0.650151] bcm63xxpart: Partition 2 is rootfs offset 146930 and length ea96d0
[    0.657585] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[    0.664841] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[    0.672098] 5 bcm63xxpart partitions found on MTD device spi1.0
[    0.678188] Creating 5 MTD partitions on "spi1.0":
[    0.683135] 0x000000000000-0x000000010000 : "CFE"
[    0.691119] 0x000000010100-0x000000146930 : "kernel"
[    0.699894] 0x000000146930-0x000000ff0000 : "rootfs"
[    0.708578] mtd: device 2 (rootfs) set to be root filesystem
[    0.715343] 1 squashfs-split partitions found on MTD device rootfs
[    0.721749] 0x000000380000-0x000000ff0000 : "rootfs_data"
[    0.730329] 0x000000ff0000-0x000001000000 : "nvram"
[    0.738979] 0x000000010000-0x000000ff0000 : "linux"
[    0.786721] b53_common: found switch: BCM63xx, rev 0
[    0.792356] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.801264] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.807186] bcma: bus0: Found chip with id 43227, rev 0x01 and package 0x09
[    0.814425] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
[    0.823252] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0)
[    0.832195] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x14, class 0x0)
[    0.853707] bcma: bus0: Bus registered
[    0.860174] NET: Registered protocol family 10
[    0.871179] NET: Registered protocol family 17
[    0.875909] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.888918] 8021q: 802.1Q VLAN Support v1.8
[    0.903852] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.928272] Freeing unused kernel memory: 1268K (803c3000 - 80500000)
[    2.845839] init: Console is alive
[    2.849724] init: - watchdog -
[    4.461211] init: - preinit -
[    6.025289] random: jshn: uninitialized urandom read (4 bytes read, 113 bits of entropy available)
[    6.259213] random: jshn: uninitialized urandom read (4 bytes read, 114 bits of entropy available)
[    6.499041] random: jshn: uninitialized urandom read (4 bytes read, 115 bits of entropy available)
[    6.592964] random: jshn: uninitialized urandom read (4 bytes read, 115 bits of entropy available)
[    6.721811] random: jshn: uninitialized urandom read (4 bytes read, 116 bits of entropy available)
[    7.207374] random: procd: uninitialized urandom read (4 bytes read, 118 bits of entropy available)
[    7.229814] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 2, 100Mbps, full-duplex
[    7.238004] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 3, 100Mbps, full-duplex
[    9.865472] random: nonblocking pool is initialized
[   10.999986] jffs2: notice: (333) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   11.031028] mount_root: switching to jffs2 overlay
[   11.352771] urandom-seed: Seeding with /etc/urandom.seed
[   11.937144] procd: - early -
[   11.940315] procd: - watchdog -
[   12.681221] procd: - ubus -
[   12.760165] procd: - init -
[   13.640361] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.669387] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[   13.677272] Backport generated by backports.git backports-20160324-9-g0e38f5c
[   13.691893] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.716550] nf_conntrack version 0.5.0 (950 buckets, 3800 max)
[   13.794863] xt_time: kernel timezone is -0000
[   13.944417] PPP generic driver version 2.4.2
[   13.953996] NET: Registered protocol family 24
[   14.011351] b43-phy0: Broadcom 43227 WLAN found (core revision 30)
[   14.018828] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17
[   14.025232] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 14, Version 0
[   14.033950] Broadcom 43xx driver loaded [ Features: PNL ]
[   14.316340] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   19.137800] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 2, 100Mbps, full-duplex
[   19.145995] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 3, 100Mbps, full-duplex
[   26.525816] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 2, 100Mbps, full-duplex
[   26.534011] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 3, 100Mbps, full-duplex
[   26.552133] device eth0.1 entered promiscuous mode
[   26.557107] device eth0 entered promiscuous mode
[   26.565151] br-lan: port 1(eth0.1) entered forwarding state
[   26.570997] br-lan: port 1(eth0.1) entered forwarding state
[   28.573423] br-lan: port 1(eth0.1) entered forwarding state
[   29.918962] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[   30.072136] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   32.731591] wlan0: authenticate with 00:18:e7:b1:24:70
[   32.769895] wlan0: send auth to 00:18:e7:b1:24:70 (try 1/3)
[   32.779473] wlan0: authenticated
[   32.785736] wlan0: associate with 00:18:e7:b1:24:70 (try 1/3)
[   32.800345] wlan0: RX AssocResp from 00:18:e7:b1:24:70 (capab=0x411 status=0 aid=3)
[   32.808628] wlan0: associated
[   32.811989] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   48.541638] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 2
[24451.545758] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 2, 100Mbps, full-duplex

Powered by LuCI lede-17.01 branch (git-17.063.59066-a5191ef) / LEDE Reboot 17.01.0 r3205-59508e3