Create a gist now

Instantly share code, notes, and snippets.

anonymous /smartcl.sda1 Secret
Created Jan 4, 2017

What would you like to do?
Download ZIP
Raw
smartcl.sda1
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.23-mod-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA100
Serial Number: 13OGR9SPS
LU WWN Device Id: 5 000039 ff2e2dff8
Firmware Version: MS2OA750
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jan 4 21:22:49 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7604) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 094 094 016 Pre-fail Always - 589839
2 Throughput_Performance 0x0005 126 126 054 Pre-fail Offline - 131
3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 182 (Average 180)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 64
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1989
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 083 083 020 Pre-fail Offline - 47
9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 26826
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 64
192 Power-Off_Retract_Count 0x0032 046 046 000 Old_age Always - 65535
193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 597939
194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 21 (Min/Max 13/44)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2206
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 36 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36 occurred at disk power-on lifetime: 26824 hours (1117 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 20 e0 8d 7a 02 Error: IDNF at LBA = 0x027a8de0 = 41586144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 78 00 40 7b 40 00 00:37:52.313 WRITE FPDMA QUEUED
61 00 70 00 38 7b 40 00 00:37:52.190 WRITE FPDMA QUEUED
61 00 68 00 30 7b 40 00 00:37:52.020 WRITE FPDMA QUEUED
61 00 60 00 28 7b 40 00 00:37:51.848 WRITE FPDMA QUEUED
61 00 58 00 20 7b 40 00 00:37:51.602 WRITE FPDMA QUEUED
Error 35 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 60 a0 6a 88 02 Error: IDNF at LBA = 0x02886aa0 = 42494624
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 68 c8 28 9f 37 40 00 15:34:47.705 WRITE FPDMA QUEUED
61 00 c0 00 c4 88 40 00 15:34:47.460 WRITE FPDMA QUEUED
61 00 b0 00 c0 88 40 00 15:34:47.363 WRITE FPDMA QUEUED
61 00 a8 00 bc 88 40 00 15:34:47.109 WRITE FPDMA QUEUED
61 00 a0 00 b8 88 40 00 15:34:47.079 WRITE FPDMA QUEUED
Error 34 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 d8 28 3d 85 02 Error: IDNF at LBA = 0x02853d28 = 42286376
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 00 a8 85 40 00 15:33:15.191 WRITE FPDMA QUEUED
61 00 c8 00 a4 85 40 00 15:33:14.645 WRITE FPDMA QUEUED
61 00 b8 00 a0 85 40 00 15:33:14.624 WRITE FPDMA QUEUED
61 00 a8 00 9c 85 40 00 15:33:14.145 WRITE FPDMA QUEUED
61 00 f0 00 98 85 40 00 15:33:11.018 WRITE FPDMA QUEUED
Error 33 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 20 e0 8e 83 02 Error: IDNF at LBA = 0x02838ee0 = 42176224
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 68 00 f4 83 40 00 15:32:42.154 WRITE FPDMA QUEUED
61 00 60 00 f0 83 40 00 15:32:41.684 WRITE FPDMA QUEUED
61 00 98 00 ec 83 40 00 15:32:41.031 WRITE FPDMA QUEUED
61 00 80 00 e8 83 40 00 15:32:40.319 WRITE FPDMA QUEUED
61 00 78 00 e4 83 40 00 15:32:39.766 WRITE FPDMA QUEUED
Error 32 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 50 b0 19 7e 02 Error: IDNF at LBA = 0x027e19b0 = 41818544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 10 00 10 00 40 00 15:31:21.275 WRITE FPDMA QUEUED
61 28 08 e0 9d 37 40 00 15:31:20.155 WRITE FPDMA QUEUED
61 08 00 00 10 04 40 00 15:31:19.851 WRITE FPDMA QUEUED
61 00 f0 00 4c 7e 40 00 15:31:19.705 WRITE FPDMA QUEUED
61 00 e8 00 7c 7e 40 00 15:31:19.705 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6951 -
# 2 Short offline Completed without error 00% 6945 -
# 3 Short offline Completed without error 00% 4520 -
# 4 Short offline Completed without error 00% 4519 -
# 5 Short offline Completed without error 00% 4519 -
# 6 Short offline Completed without error 00% 4458 -
# 7 Short offline Completed without error 00% 4454 -
# 8 Short offline Completed without error 00% 2533 -
# 9 Short offline Completed without error 00% 2528 -
#10 Short offline Completed without error 00% 2528 -
#11 Short offline Completed without error 00% 59 -
#12 Short offline Completed without error 00% 55 -
#13 Short offline Completed without error 00% 55 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Raw
smartcl.sda2
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.23-mod-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA100
Serial Number: 13OGR9SPS
LU WWN Device Id: 5 000039 ff2e2dff8
Firmware Version: MS2OA750
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jan 4 21:24:36 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7604) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 094 094 016 Pre-fail Always - 589839
2 Throughput_Performance 0x0005 126 126 054 Pre-fail Offline - 131
3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 182 (Average 180)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 64
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1989
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 083 083 020 Pre-fail Offline - 47
9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 26826
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 64
192 Power-Off_Retract_Count 0x0032 046 046 000 Old_age Always - 65535
193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 597939
194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 21 (Min/Max 13/44)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2206
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 36 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36 occurred at disk power-on lifetime: 26824 hours (1117 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 20 e0 8d 7a 02 Error: IDNF at LBA = 0x027a8de0 = 41586144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 78 00 40 7b 40 00 00:37:52.313 WRITE FPDMA QUEUED
61 00 70 00 38 7b 40 00 00:37:52.190 WRITE FPDMA QUEUED
61 00 68 00 30 7b 40 00 00:37:52.020 WRITE FPDMA QUEUED
61 00 60 00 28 7b 40 00 00:37:51.848 WRITE FPDMA QUEUED
61 00 58 00 20 7b 40 00 00:37:51.602 WRITE FPDMA QUEUED
Error 35 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 60 a0 6a 88 02 Error: IDNF at LBA = 0x02886aa0 = 42494624
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 68 c8 28 9f 37 40 00 15:34:47.705 WRITE FPDMA QUEUED
61 00 c0 00 c4 88 40 00 15:34:47.460 WRITE FPDMA QUEUED
61 00 b0 00 c0 88 40 00 15:34:47.363 WRITE FPDMA QUEUED
61 00 a8 00 bc 88 40 00 15:34:47.109 WRITE FPDMA QUEUED
61 00 a0 00 b8 88 40 00 15:34:47.079 WRITE FPDMA QUEUED
Error 34 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 d8 28 3d 85 02 Error: IDNF at LBA = 0x02853d28 = 42286376
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 00 a8 85 40 00 15:33:15.191 WRITE FPDMA QUEUED
61 00 c8 00 a4 85 40 00 15:33:14.645 WRITE FPDMA QUEUED
61 00 b8 00 a0 85 40 00 15:33:14.624 WRITE FPDMA QUEUED
61 00 a8 00 9c 85 40 00 15:33:14.145 WRITE FPDMA QUEUED
61 00 f0 00 98 85 40 00 15:33:11.018 WRITE FPDMA QUEUED
Error 33 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 20 e0 8e 83 02 Error: IDNF at LBA = 0x02838ee0 = 42176224
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 68 00 f4 83 40 00 15:32:42.154 WRITE FPDMA QUEUED
61 00 60 00 f0 83 40 00 15:32:41.684 WRITE FPDMA QUEUED
61 00 98 00 ec 83 40 00 15:32:41.031 WRITE FPDMA QUEUED
61 00 80 00 e8 83 40 00 15:32:40.319 WRITE FPDMA QUEUED
61 00 78 00 e4 83 40 00 15:32:39.766 WRITE FPDMA QUEUED
Error 32 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 50 b0 19 7e 02 Error: IDNF at LBA = 0x027e19b0 = 41818544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 10 00 10 00 40 00 15:31:21.275 WRITE FPDMA QUEUED
61 28 08 e0 9d 37 40 00 15:31:20.155 WRITE FPDMA QUEUED
61 08 00 00 10 04 40 00 15:31:19.851 WRITE FPDMA QUEUED
61 00 f0 00 4c 7e 40 00 15:31:19.705 WRITE FPDMA QUEUED
61 00 e8 00 7c 7e 40 00 15:31:19.705 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6951 -
# 2 Short offline Completed without error 00% 6945 -
# 3 Short offline Completed without error 00% 4520 -
# 4 Short offline Completed without error 00% 4519 -
# 5 Short offline Completed without error 00% 4519 -
# 6 Short offline Completed without error 00% 4458 -
# 7 Short offline Completed without error 00% 4454 -
# 8 Short offline Completed without error 00% 2533 -
# 9 Short offline Completed without error 00% 2528 -
#10 Short offline Completed without error 00% 2528 -
#11 Short offline Completed without error 00% 59 -
#12 Short offline Completed without error 00% 55 -
#13 Short offline Completed without error 00% 55 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Raw
smartcl.sda3
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.23-mod-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA100
Serial Number: 13OGR9SPS
LU WWN Device Id: 5 000039 ff2e2dff8
Firmware Version: MS2OA750
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jan 4 21:25:19 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7604) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 094 094 016 Pre-fail Always - 589839
2 Throughput_Performance 0x0005 126 126 054 Pre-fail Offline - 131
3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 182 (Average 180)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 64
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1989
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 083 083 020 Pre-fail Offline - 47
9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 26826
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 64
192 Power-Off_Retract_Count 0x0032 046 046 000 Old_age Always - 65535
193 Load_Cycle_Count 0x0012 001 001 000 Old_age Always - 597939
194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 21 (Min/Max 13/44)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2206
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 36 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36 occurred at disk power-on lifetime: 26824 hours (1117 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 20 e0 8d 7a 02 Error: IDNF at LBA = 0x027a8de0 = 41586144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 78 00 40 7b 40 00 00:37:52.313 WRITE FPDMA QUEUED
61 00 70 00 38 7b 40 00 00:37:52.190 WRITE FPDMA QUEUED
61 00 68 00 30 7b 40 00 00:37:52.020 WRITE FPDMA QUEUED
61 00 60 00 28 7b 40 00 00:37:51.848 WRITE FPDMA QUEUED
61 00 58 00 20 7b 40 00 00:37:51.602 WRITE FPDMA QUEUED
Error 35 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 60 a0 6a 88 02 Error: IDNF at LBA = 0x02886aa0 = 42494624
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 68 c8 28 9f 37 40 00 15:34:47.705 WRITE FPDMA QUEUED
61 00 c0 00 c4 88 40 00 15:34:47.460 WRITE FPDMA QUEUED
61 00 b0 00 c0 88 40 00 15:34:47.363 WRITE FPDMA QUEUED
61 00 a8 00 bc 88 40 00 15:34:47.109 WRITE FPDMA QUEUED
61 00 a0 00 b8 88 40 00 15:34:47.079 WRITE FPDMA QUEUED
Error 34 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 d8 28 3d 85 02 Error: IDNF at LBA = 0x02853d28 = 42286376
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 00 a8 85 40 00 15:33:15.191 WRITE FPDMA QUEUED
61 00 c8 00 a4 85 40 00 15:33:14.645 WRITE FPDMA QUEUED
61 00 b8 00 a0 85 40 00 15:33:14.624 WRITE FPDMA QUEUED
61 00 a8 00 9c 85 40 00 15:33:14.145 WRITE FPDMA QUEUED
61 00 f0 00 98 85 40 00 15:33:11.018 WRITE FPDMA QUEUED
Error 33 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 20 e0 8e 83 02 Error: IDNF at LBA = 0x02838ee0 = 42176224
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 68 00 f4 83 40 00 15:32:42.154 WRITE FPDMA QUEUED
61 00 60 00 f0 83 40 00 15:32:41.684 WRITE FPDMA QUEUED
61 00 98 00 ec 83 40 00 15:32:41.031 WRITE FPDMA QUEUED
61 00 80 00 e8 83 40 00 15:32:40.319 WRITE FPDMA QUEUED
61 00 78 00 e4 83 40 00 15:32:39.766 WRITE FPDMA QUEUED
Error 32 occurred at disk power-on lifetime: 26823 hours (1117 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 50 b0 19 7e 02 Error: IDNF at LBA = 0x027e19b0 = 41818544
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 10 00 10 00 40 00 15:31:21.275 WRITE FPDMA QUEUED
61 28 08 e0 9d 37 40 00 15:31:20.155 WRITE FPDMA QUEUED
61 08 00 00 10 04 40 00 15:31:19.851 WRITE FPDMA QUEUED
61 00 f0 00 4c 7e 40 00 15:31:19.705 WRITE FPDMA QUEUED
61 00 e8 00 7c 7e 40 00 15:31:19.705 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6951 -
# 2 Short offline Completed without error 00% 6945 -
# 3 Short offline Completed without error 00% 4520 -
# 4 Short offline Completed without error 00% 4519 -
# 5 Short offline Completed without error 00% 4519 -
# 6 Short offline Completed without error 00% 4458 -
# 7 Short offline Completed without error 00% 4454 -
# 8 Short offline Completed without error 00% 2533 -
# 9 Short offline Completed without error 00% 2528 -
#10 Short offline Completed without error 00% 2528 -
#11 Short offline Completed without error 00% 59 -
#12 Short offline Completed without error 00% 55 -
#13 Short offline Completed without error 00% 55 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment