China Projector Melody

 ======= Whole Chip Reset =======
[Melody] BD_MST096B_10ARU_15384
[Melody] SPI BOOT
[v] Console Initial OK
[Melody] DDR2 64M
[12345678][123456789][123456789][12345678]
4554

    BIST_0 PASS.

 MIU Initial OK

Hello Melody:A0000000 Oct 11 2019 17:24:34
Oct 11 2019
17:24:34

sboot use 1627ms
  _readonly_start=0x243000, _readonly_end=0x3B1000
MIU protect align=0xC, 0x1000
Beon protect start=240000, end=5C0000
MDrv_MIU_Protect rtn 1
@@@@@@ u32CpuSpeedMHz= 216 MHz

======================================
== Chakra3 Software Version: [0]
[DRAM SIZE]: 64 MB
[FLASH SIZE]: 4 MB
[SW_CONFIG]: SW_CONFIG_TRUNK_MELODY_64M_ATVMM
[Board]: BD_MST096B_10ARU_15384
[Panel]: tPNL_OTM8009A_TTL_LVDS111
[MEMORY_MAP]: MMAP_64MB
[ATV]: PAL
[ENABLE_TTX]: 1
[Mirror]: 0
[ENABLE_PWS]: 1
[ENABLE_POWER_SAVING_DPMS]: 1
[DEMO_FINE_TUNE]: DFT_STD_ORIGINAL_SETTING
[ENABLE_DLC]: 1
[DISPLAY_LOGO]: 1
[AUTO BUILD VER]: 0
[FRONTEND_TUNER_TYPE]: RAFAEL_R840_TUNER

======================================
wPM_WakeUpDevice 0x85
=> DC_BOOT (1)
PM Wakeup by 0x8
MDrv_Power_PMPowerRst() Line 138:
MApp_Audio_Set_AmpMute(1)
MApp_Audio_Set_AmpOnOff(bAmpOn=1)
create Audio SHM data ...
MApp_LCD_SPLIN
g_u16Miu0_Dqs0~~~~~________-0x=3FE
g_u16Miu0_Dqs1~~~~~_________0x=3FE
 USB_Init_Configure port 0
USB_Init_Configure port 0 done...
 USB_Init_Configure port 1
USB_Init_Configure port 1 done...
Flash is detected (0x0709, 0xEF, 0x40, 0x16)
MApp_DB_Check()
msAPI_Flash_Init()
 => u32FlashSize=0x400000
 => s_Flash_u32WriteValidAddr_Start=0x3C0000
 => s_Flash_u32WriteValidAddr_End=0x3FFFFF
MApp_DB_GEN_Init()
=> GoodUnit=11, WriteTime=364

=================================
msAPI_DB_GEN_Printf_Variable():
 s_stDB_GEN_InitData:
 u8FlashBank: 0x3E
 .u16FlashSaveUnitSize: 4096
 .u32DramDataAddr: 0xB79000
 .u16DramDataSize: 1900
 u8FlashUnitNumPer1Bank=16
 u8FlashUnitNumTotal=32
 u16FlashUnitInfoOffset=0xFE0
=================================

=================================
msAPI_DB_CH_Printf_Variable():
 s_stDB_CH_InitData:
 u8FlashBankStart: 0x3C
 .u8FlashSaveBankCount: 1
 .u32DramDataAddr: 0xB7A000
 .u32DramDataSize: 0x118C
 u8FlashBankStart_0=0x3C
 u8FlashBankStart_1=0x3D
 u32CheckDataOffset=0xFFF0
=================================
DC on

Auth OK

    ====== HAL_AUDSP_DspLoadCode: 0xA0 ======
Load Audio DSP code (SE adv_none)
    PM addr: 0x3EC0
    PM buf addr: 0x462B61
    PM size: 0x1E
  Dsp code verify ok!!
    CM addr: 0x17A0
    CM buf addr: 0x462B3A
    CM size: 0x21
  Dsp code verify ok!!
    Cache PM addr: 0x9800
    Cache PM buf addr: 0x462B85
    Cache PM size: 0x3
    MIU of Cache: 0x664800
HAL_AUDSP_DspLoadCode finished(type=SE adv_none(0xA0))
[[supernova]]      MApi_AUDIO_SetCommand() : Audio system is not ready yet, please try again later
    ====== HAL_AUDSP_DspLoadCode: 0x3 ======
Load Audio DSP code (mpeg)
    PM addr: 0x1AC0
    PM buf addr: 0x463671
    PM size: 0x1E96
  Dsp code verify ok!!
    CM addr: 0xC60
    CM buf addr: 0x462B8E
    CM size: 0xADD
  Dsp code verify ok!!
    Cache PM addr: 0x5800
    Cache PM buf addr: 0x46550D
    Cache PM size: 0x190B
    MIU of Cache: 0x658800
    PreFetch PM addr: 0xA700
    PreFetch PM buf addr: 0x466E1E
    PreFetch PM size: 0x1710
    MIU of PreFetch: 0x667500
HAL_AUDSP_DspLoadCode finished(type=mpeg(0x3))
    ====== HAL_AUDSP_DspLoadCode: 0x50 ======
Load Audio DSP code (EDEN system)
    PM addr: 0x17FF
    PM buf addr: 0x45D0CE
    PM size: 0x76E
  Dsp code verify ok!!
    CM addr: 0x8
    CM buf addr: 0x45B14E
    CM size: 0x1F7A
  Dsp code verify ok!!
    Cache PM addr: 0x4000
    Cache PM buf addr: 0x45D842
    Cache PM size: 0x466E
    MIU of Cache: 0x654000
    PreFetch PM addr: 0xA300
    PreFetch PM buf addr: 0x461EB6
    PreFetch PM size: 0xC00
    MIU of PreFetch: 0x666900
  Dsp code verify ok!!
  Dsp code verify ok!!
HAL_AUDSP_DspLoadCode finished(type=EDEN system(0x50))
===== Check Audio Decoder Protection from hash-key IP =====
Hash-key Support DD.
Hash-key Support DD+.
Hash-key Support Dolby Pulse(MS10-DDT).
Hash-key Support DTS DMP.
Hash-key Support WMA.
Hash Key Check DRA Fail, No DRA license!!
Hash Key Check DTSLBR Fail, No DTSLBR license!!
===== Check Protection IP End                         =====
---------- spkrMute ----------
    ====== HAL_AUDSP_DspLoadCode: 0x46 ======
Load Audio DSP code (tshd)
    PM addr: 0x3EC0
    PM buf addr: 0x474642
    PM size: 0x2E8
  Dsp code verify ok!!
    CM addr: 0x17A0
    CM buf addr: 0x474546
    CM size: 0xF6
  Dsp code verify ok!!
    Cache PM addr: 0x9800
    Cache PM buf addr: 0x474930
    Cache PM size: 0x15BA
    MIU of Cache: 0x664800
HAL_AUDSP_DspLoadCode finished(type=tshd(0x46))
MDrv_PNL_Init u32PnlRiuBaseAddr = A0200000
MDrv_PNL_Init u32PMRiuBaseAddr = A0000000
[_MDrv_PNL_Init_LPLL][295]pstPanelInitData->u16Width=800, pstPanelInitData->u16Height=480
[_MDrv_PNL_Init_LPLL][297]u16HTotal=825,u16VTotal=1240,pstPanelInitData->u16HTotal=825,pstPanelInitData->u16VTotal=1240, u16DefaultVFreq=600
[_MDrv_PNL_Init_Output_Dclk][340]pstPanelInitData->u16Width=800, pstPanelInitData->u16Height=480
[_MDrv_PNL_Init_Output_Dclk][342]u16HTotal=825,u16VTotal=1240,pstPanelInitData->u16HTotal=825,pstPanelInitData->u16VTotal=1240, u16DefaultVFreq=600
[XC,Version] 00442327
 MApi_XC_Init, 552, pXC_InitData->stPanelInfo.eLPLL_Type=1

HDMI port status: --------------------------------------------
0 Hpd=2, Clk=2
1 Hpd=2, Clk=2
2 Hpd=2, Clk=2
3 Hpd=2, Clk=2
----------------------------------------------------------------
>> MDrv_DVI_Software_Reset(eInputPort=81, BIT5)
>> MDrv_DVI_Software_Reset(eInputPort=83, BIT5)
MApi_XC_SetupFrameBuffer(src=41)
=> XC-Main = SCALER_DNR_BUF
 u32MainAddr=0x20E0000, u32MainSize=0xC00000
driver IR init ok

Keypad Initialize OK

[GOP_ALL, PID 0][Driver Version]: 0088, BuildNum: 0488, ChangeList: 2147483647
====================
First GOP driver instance, flush GWIN HW
====================

....0x102F1A=0....
MApp_Init_LCD
MApp_InputSrc_Set_PrevUiInputSrcType(src=8)
u32ReadBuffVirAddr = 80CE0000, u32IntBuffVirAddr = 813E0000, u32OutBuffVirAddr = 82CE0000
verJPD_SetStatus >>>>>>>>>>> w:800,  h:480,  p:800

[GOP0, PID 0][Driver Version]: 0088, BuildNum: 0488, ChangeList: 2147483647

-----I2C_Write_Len error------R840_Init error
[Error]device/tuner/R_R840.c,630
DSP code loaded successfully
 >> MApp_InputSource_SwitchSource(8[HDMI1])
 OldUiSrc=15(NONE), eOldInputSrc=41

---------- spkrMute ----------
 eNewInputSrc=23
MApp_PCMode_Reset()
MApp_PCMODE_Reset_TimingMonitor()
    ====== HAL_AUDSP_DspLoadCode: 0x4 ======
Load Audio DSP code (ac3p)
    PM addr: 0x1AC0
    PM buf addr: 0x4799B2
    PM size: 0x3
  Dsp code verify ok!!
    CM addr: 0xC60
    CM buf addr: 0x477EA0
    CM size: 0x1B0C
  Dsp code verify ok!!
    Cache PM addr: 0x5800
    Cache PM buf addr: 0x4799BB
    Cache PM size: 0xB118
    MIU of Cache: 0x658800
    PreFetch PM addr: 0xA700
    PreFetch PM buf addr: 0x484AD9
    PreFetch PM size: 0xA1A0
    MIU of PreFetch: 0x667500
HAL_AUDSP_DspLoadCode finished(type=ac3p(0x4))

 enInputSourceType = 23
>> MDrv_DVI_Software_Reset(eInputPort=81, BIT5)
MApi_XC_SetupFrameBuffer(src=23)
=> XC-Main = SCALER_DNR_BUF
 u32MainAddr=0x20E0000, u32MainSize=0xC00000
MApp_Audio_Set_AmpMute(0)
unsupport N51 FS compress
MApp_PreInit_Others_Init()
[Unsupported Resolution: 800 x 480
]
===== Enter main loop at 11098

===== Timestamp Oct 11 2019, 17:12:55
MiscSetting setting changed(E1F0,F1D1)
VideoMute[0]=0x4 Freerun,
 DB_GEN: Write flash done~ => UnitIdx=12, wt=365, use 5ms

 BlueScreen Open when Source Change
VideoMute[0]=0x4 Freerun,
VideoMute[0]=0x4 Freerun,
VideoMute[0]=0x4 Freerun,
VideoMute[0]=0x4 Freerun,
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 MultiTask 455582 use 98 at 36050!
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
VideoMute[0]=0x4 Freerun,
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
 CH[0] = 00
MApp_Audio_Set_AmpMute(1)
MApp_Audio_Set_AmpOnOff(bAmpOn=0)
 CH[0] = 00
MApp_LCD_SPLIN
MApp_DB_SaveDataBase_RightNow(0x1)
 DB_GEN: Write flash done~ => UnitIdx=13, wt=366, use 5ms
MApp_DB_SaveDataBase_RightNow() done~
 CH[0] = 00
 msAPI_Power_SetPowerMode = 0x3412

 ~~~ POWER DOWN ~~~

MDrv_Power_ExecutePowerDown
=> StandBy
1. wPM_WakeUpDevice = 0x85
WakeUpFlag=0x85 {}
2.wPM_WakeUpDevice = 0x85
WakeUpFlag=0x85 {}
 msAPI_Power_SetWakeUpDevice = 0x85
MApp_Audio_Set_AmpMute(1)
Disable Aeon
isable Aeon Done
[PM_MELODY] Hello
[PM_MELODY] Console Initial OK
[msKeypad_Init]: Allocated channel number > 1 !!!
                                                 [PM_MELODY] Enter Standby Loop
[PM_MELODY] Looping...
[PM_MELODY] Looping...
[PM_MELODY] Looping...
[PM_MELODY] Looping...
[PM_MELODY] Looping...
[PM_MELODY] Looping...
[PM_MELODY] Looping...