Created
September 4, 2016 13:29
-
-
Save bigjosh/f4275679fd0629cb45592d28c1029d99 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| root@beaglebone:~# iw list | |
| Wiphy phy0 | |
| max # scan SSIDs: 4 | |
| max scan IEs length: 2257 bytes | |
| Retry short limit: 7 | |
| Retry long limit: 4 | |
| Coverage class: 0 (up to 0m) | |
| Device supports RSN-IBSS. | |
| Supported Ciphers: | |
| * WEP40 (00-0f-ac:1) | |
| * WEP104 (00-0f-ac:5) | |
| * TKIP (00-0f-ac:2) | |
| * CCMP (00-0f-ac:4) | |
| * 00-0f-ac:10 | |
| * GCMP (00-0f-ac:8) | |
| * 00-0f-ac:9 | |
| Available Antennas: TX 0 RX 0 | |
| Supported interface modes: | |
| * IBSS | |
| * managed | |
| * AP | |
| * AP/VLAN | |
| * WDS | |
| * monitor | |
| * mesh point | |
| Band 1: | |
| Capabilities: 0x172 | |
| HT20/HT40 | |
| Static SM Power Save | |
| RX Greenfield | |
| RX HT20 SGI | |
| RX HT40 SGI | |
| RX STBC 1-stream | |
| Max AMSDU length: 3839 bytes | |
| No DSSS/CCK HT40 | |
| Maximum RX AMPDU length 65535 bytes (exponent: 0x003) | |
| Minimum RX AMPDU time spacing: 2 usec (0x04) | |
| HT RX MCS rate indexes supported: 0-7, 32 | |
| TX unequal modulation not supported | |
| HT TX Max spatial streams: 1 | |
| HT TX MCS rate indexes supported may differ | |
| Bitrates (non-HT): | |
| * 1.0 Mbps | |
| * 2.0 Mbps (short preamble supported) | |
| * 5.5 Mbps (short preamble supported) | |
| * 11.0 Mbps (short preamble supported) | |
| * 6.0 Mbps | |
| * 9.0 Mbps | |
| * 12.0 Mbps | |
| * 18.0 Mbps | |
| * 24.0 Mbps | |
| * 36.0 Mbps | |
| * 48.0 Mbps | |
| * 54.0 Mbps | |
| Frequencies: | |
| * 2412 MHz [1] (20.0 dBm) | |
| * 2417 MHz [2] (20.0 dBm) | |
| * 2422 MHz [3] (20.0 dBm) | |
| * 2427 MHz [4] (20.0 dBm) | |
| * 2432 MHz [5] (20.0 dBm) | |
| * 2437 MHz [6] (20.0 dBm) | |
| * 2442 MHz [7] (20.0 dBm) | |
| * 2447 MHz [8] (20.0 dBm) | |
| * 2452 MHz [9] (20.0 dBm) | |
| * 2457 MHz [10] (20.0 dBm) | |
| * 2462 MHz [11] (20.0 dBm) | |
| * 2467 MHz [12] (20.0 dBm) (no IR) | |
| * 2472 MHz [13] (20.0 dBm) (no IR) | |
| * 2484 MHz [14] (20.0 dBm) (no IR) | |
| Supported commands: | |
| * new_interface | |
| * set_interface | |
| * new_key | |
| * start_ap | |
| * new_station | |
| * new_mpath | |
| * set_mesh_config | |
| * set_bss | |
| * authenticate | |
| * associate | |
| * deauthenticate | |
| * disassociate | |
| * join_ibss | |
| * join_mesh | |
| * set_tx_bitrate_mask | |
| * frame | |
| * frame_wait_cancel | |
| * set_wiphy_netns | |
| * set_channel | |
| * set_wds_peer | |
| * probe_client | |
| * set_noack_map | |
| * register_beacons | |
| * start_p2p_device | |
| * set_mcast_rate | |
| * Unknown command (104) | |
| * connect | |
| * disconnect | |
| Supported TX frame types: | |
| * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 | |
| Supported RX frame types: | |
| * IBSS: 0x40 0xb0 0xc0 0xd0 | |
| * managed: 0x40 0xd0 | |
| * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * mesh point: 0xb0 0xc0 0xd0 | |
| * P2P-client: 0x40 0xd0 | |
| * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 | |
| * P2P-device: 0x40 0xd0 | |
| software interface modes (can always be added): | |
| * AP/VLAN | |
| * monitor | |
| valid interface combinations: | |
| * #{ AP, mesh point } <= 8, | |
| total <= 8, #channels <= 1 | |
| HT Capability overrides: | |
| * MCS: ff ff ff ff ff ff ff ff ff ff | |
| * maximum A-MSDU length | |
| * supported channel width | |
| * short GI for 40 MHz | |
| * max A-MPDU length exponent | |
| * min MPDU start spacing | |
| Device supports TX status socket option. | |
| Device supports HT-IBSS. | |
| Device supports SAE with AUTHENTICATE command | |
| Device supports low priority scan. | |
| Device supports scan flush. | |
| Device supports AP scan. | |
| Device supports per-vif TX power setting | |
| Driver supports a userspace MPM |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment