Skip to content

Instantly share code, notes, and snippets.

@bogdanr

bogdanr/dmesg

Created December 28, 2013 13:16
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save bogdanr/8159402 to your computer and use it in GitHub Desktop.
Save bogdanr/8159402 to your computer and use it in GitHub Desktop.
Download ZIP
HLK-RM02 - Boot of the minimal image
Raw
dmesg
[ 0.000000] Linux version 3.10.13 (bogdan@osc) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38333) ) #5 Sat Dec 28 12:30:53 EET 2013
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is HILINK HLK-RM04
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 01000000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x00ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x00ffffff]
[ 0.000000] On node 0 totalpages: 4096
[ 0.000000] free_area_init_node: node 0, pgdat 8024e5a0, node_mem_map 802c0f20
[ 0.000000] Normal zone: 32 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 4096 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 mem=16M quiet
[ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
[ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Writing ErrCtl register=00058f10
[ 0.000000] Readback ErrCtl register=00058f10
[ 0.000000] Memory: 13364k/16384k available (2059k kernel code, 3020k reserved, 367k data, 196k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] CPU Clock: 360MHz
[ 0.060000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] pinctrl core: initialized pinctrl subsystem
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] rt2880-pinmux pinctrl.1: try to register 42 pins ...
[ 0.090000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
[ 0.090000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
[ 0.090000] pinctrl core: add 3 pinmux maps
[ 0.090000] rt2880-pinmux pinctrl.1: found group selector 4 for jtag
[ 0.090000] rt2880-pinmux pinctrl.1: invalid group "rgmii" for function "gpio"
[ 0.100000] rt2880-pinmux pinctrl.1: invalid group "mdio" for function "gpio"
[ 0.130000] bio: create slab <bio-0> at 0
[ 0.130000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.140000] Switching to clocksource MIPS
[ 0.150000] NET: Registered protocol family 2
[ 0.150000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.150000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.150000] TCP: Hash tables configured (established 512 bind 512)
[ 0.150000] TCP: reno registered
[ 0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.150000] NET: Registered protocol family 1
[ 0.150000] rt-timer 10000100.timer: maximum frequncy is 7324Hz
[ 0.150000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[ 0.190000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.190000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.190000] msgmni has been set to 26
[ 0.190000] io scheduler noop registered
[ 0.190000] io scheduler deadline registered (default)
[ 0.190000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.190000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[ 0.190000] pinctrl core: add 1 pinmux maps
[ 0.200000] rt2880-pinmux pinctrl.1: found group selector 3 for uartlite
[ 0.200000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for 10000c00.uartlite
[ 0.200000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for 10000c00.uartlite
[ 0.200000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.200000] console [ttyS0] enabled, bootconsole disabled
[ 0.200000] 10000500.uart: ttyS1 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.210000] m25p80 spi32766.0: found w25q32, expected s25fl064k
[ 0.210000] m25p80 spi32766.0: w25q32 (4096 Kbytes)
[ 0.210000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.210000] Creating 4 MTD partitions on "spi32766.0":
[ 0.210000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.210000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.220000] 0x000000040000-0x000000050000 : "factory"
[ 0.220000] 0x000000050000-0x000000400000 : "firmware"
[ 0.220000] 0x000000122b22-0x000000400000 : "rootfs"
[ 0.220000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.230000] mtd: partition "rootfs" set to be root filesystem
[ 0.230000] mtd: partition "rootfs_data" created automatically, ofs=0x250000, len=0x1b0000
[ 0.230000] 0x000000250000-0x000000400000 : "rootfs_data"
[ 0.240000] eth0: done loading
[ 0.240000] rt3xxx-usbphy ubsphy.3: loaded
[ 0.250000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.250000] TCP: cubic registered
[ 0.250000] NET: Registered protocol family 17
[ 0.250000] 8021q: 802.1Q VLAN Support v1.8
[ 0.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.270000] Freeing unused kernel memory: 196K (8025f000 - 80290000)
[ 5.090000] Button Hotplug driver version 0.4.1
[ 5.090000] leds-gpio gpio-leds.5: pins are not configured from the driver
[ 5.090000] rt2880-pinmux pinctrl.1: request pin 0 (io0) for pio:0
[ 5.100000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pio:14
[ 5.100000] rt2880-pinmux pinctrl.1: pin 14 is not set to gpio mux
[ 5.110000] rt2880-pinmux pinctrl.1: request() failed for pin 14
[ 5.120000] rt2880-pinmux pinctrl.1: pin-14 (pio:14) status -22
[ 5.130000] gpio-keys-polled gpio-keys-polled.4: unable to claim gpio 14, err=-22
[ 5.150000] gpio-keys-polled: probe of gpio-keys-polled.4 failed with error -22
[ 5.630000] rt305x-esw 10110000.esw: link changed 0x00
[ 7.220000] rt305x-esw 10110000.esw: link changed 0x08
[ 9.860000] NET: Registered protocol family 10
[ 9.880000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 9.880000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 9.910000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.910000] cfg80211: World regulatory domain updated:
[ 9.910000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.910000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.910000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.910000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.910000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.910000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.010000] rt2800_wmac 10180000.wmac: failed to load eeprom property
[ 10.030000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 10.210000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 10.210000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 10.210000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.670000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 15.670000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 21.160000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 32.990000] wlan0: authenticate with 58:6d:8f:02:34:83
[ 33.010000] wlan0: send auth to 58:6d:8f:02:34:83 (try 1/3)
[ 33.010000] wlan0: authenticated
[ 33.020000] wlan0: associate with 58:6d:8f:02:34:83 (try 1/3)
[ 33.020000] wlan0: RX AssocResp from 58:6d:8f:02:34:83 (capab=0x411 status=0 aid=7)
[ 33.020000] wlan0: associated
[ 33.020000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.670000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 34.850000] jffs2: notice: (551) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Raw
lsmod
arc4 1232 2
button_hotplug 2720 0
cfg80211 165088 2 rt2x00lib
compat 528 3 rt2800pci
crc_ccitt 944 1 rt2800lib
crypto_blkcipher 9616 1 arc4
crypto_hash 8304 0
eeprom_93cx6 1632 0
gpio_keys_polled 3376 0
input_core 22784 3 gpio_keys_polled
input_polldev 1696 1 gpio_keys_polled
ipv6 225120 14
leds_gpio 2896 0
ledtrig_gpio 1952 0
ledtrig_heartbeat 1056 0
ledtrig_morse 1728 0
ledtrig_oneshot 1488 0
mac80211 296400 3 rt2800lib
rt2800lib 71728 1 rt2800pci
rt2800pci 6768 0
rt2x00lib 29920 4 rt2800pci
rt2x00mmio 1712 1 rt2800pci
rt2x00soc 1104 1 rt2800pci
Raw
ps w
PID USER VSZ STAT COMMAND
1 root 1376 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW< [kworker/0:0H]
7 root 0 SW< [khelper]
8 root 0 SW [kworker/u2:1]
64 root 0 SW< [writeback]
66 root 0 SW< [bioset]
68 root 0 SW< [kblockd]
97 root 0 SW [kswapd0]
142 root 0 SW [fsnotify_mark]
168 root 0 SW [spi32766]
208 root 0 SW< [deferwq]
318 root 880 S < ubusd
319 root 1508 S /bin/ash --login
357 root 0 SW [kworker/0:2]
358 root 0 SW< [cfg80211]
455 root 1496 S /sbin/netifd
544 root 1496 S udhcpc -p /var/run/udhcpc-eth0.2.pid -s /lib/netifd/dhcp.script -f -t 0 -i eth0.2 -C
672 root 1588 S wpa_supplicant -B -P /var/run/wifi-wlan0.pid -D nl80211 -i wlan0 -c /var/run/wpa_supplicant-wlan0.conf
682 root 0 SW [kworker/u2:2]
696 root 0 SWN [jffs2_gcd_mtd5]
708 root 1508 S udhcpc -p /var/run/udhcpc-wlan0.pid -s /lib/netifd/dhcp.script -f -t 0 -i wlan0 -C
749 root 1496 S /usr/sbin/ntpd -n -p 0.ro.pool.ntp.org -p 1.ro.pool.ntp.org -p 2.ro.pool.ntp.org -p 3.ro.pool.ntp.org
752 root 804 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 wlan0
753 root 0 SW< [kworker/0:1H]
801 root 1156 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22
956 root 1492 R ps w
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment