/etc/teleport.yaml of Teleport cluster located inside of company

gistfile1.txt

# By default, this file should be stored in /etc/teleport.yaml
 
# This section of the configuration file applies to all teleport
# services.
teleport:
    # nodename allows to assign an alternative name this node can be reached by.
    # by default it's equal to hostname
    nodename: remote
 
    # Data directory where Teleport daemon keeps its data.
    # See "Filesystem Layout" section above for more details.
    data_dir: /var/lib/teleport
 
    # Invitation token used to join a cluster. it is not used on
    # subsequent starts
    auth_token: xxxx-token-xxxx
 
    # Optional CA pin of the auth server. This enables more secure way of adding new
    # nodes to a cluster. See "Adding Nodes" section above.
    ca_pin: "sha256:7e12c17c20d9cb504bbcb3f0236be3f446861f1396dcbb44425fe28ec1c108f1"
 
    # When running in multi-homed or NATed environments Teleport nodes need
    # to know which IP it will be reachable at by other nodes
    #
    # This value can be specified as FQDN e.g. host.example.com
    advertise_ip: remote.example.com
 
    # list of auth servers in a cluster. you will have more than one auth server
    # if you configure teleport auth to run in HA configuration
    auth_servers:
        - OFFICE_Private_IP:3025
 
    # Teleport throttles all connections to avoid abuse. These settings allow
    # you to adjust the default limits
    connection_limits:
        max_connections: 1000
        max_users: 250
 
    # Logging configuration. Possible output values are 'stdout', 'stderr' and
    # 'syslog'. Possible severity values are INFO, WARN and ERROR (default).
    log:
        output: stderr
        severity: DEBUG
 
    # Configuration for the storage back-end used for the cluster state and the
    # audit log. Several back-end types are supported. See "High Availability"
    # section of this Admin Manual below to learn how to configure DynamoDB,
    # S3, etcd and other highly available back-ends.
#    storage:
        # By default teleport uses the `data_dir` directory on a local filesystem
#        type: dir
 
        # Array of locations where the audit log events will be stored. by
        # default they are stored in `/var/lib/teleport/log`
#        audit_events_uri: ['file:///var/lib/teleport/log', 'dynamodb://events_table_name']
 
        # Use this setting to configure teleport to store the recorded sessions in
        # an AWS S3 bucket. see "Using Amazon S3" chapter for more information.
#        audit_sessions_uri: 's3://bucket/?region=us-east-1'
 
 
    # Cipher algorithms that the server supports. This section only needs to be
    # set if you want to override the defaults.
    ciphers:
      - aes128-ctr
      - aes192-ctr
      - aes256-ctr
      - aes128-gcm@openssh.com
#      - arcfour256
#      - arcfour128
 
    # Key exchange algorithms that the server supports. This section only needs
    # to be set if you want to override the defaults.
    kex_algos:
      - curve25519-sha256@libssh.org
      - ecdh-sha2-nistp256
      - ecdh-sha2-nistp384
      - ecdh-sha2-nistp521
      - diffie-hellman-group14-sha1
      - diffie-hellman-group1-sha1
 
    # Message authentication code (MAC) algorithms that the server supports.
    # This section only needs to be set if you want to override the defaults.
    mac_algos:
      - hmac-sha2-256-etm@openssh.com
      - hmac-sha2-256
      - hmac-sha1
      - hmac-sha1-96
 
    # List of the supported ciphersuites. If this section is not specified,
    # only the default ciphersuites are enabled.
    ciphersuites:
       - tls-rsa-with-aes-128-cbc-sha # default
       - tls-rsa-with-aes-256-cbc-sha # default
       - tls-rsa-with-aes-128-cbc-sha256
       - tls-rsa-with-aes-128-gcm-sha256
       - tls-rsa-with-aes-256-gcm-sha384
       - tls-ecdhe-ecdsa-with-aes-128-cbc-sha
       - tls-ecdhe-ecdsa-with-aes-256-cbc-sha
       - tls-ecdhe-rsa-with-aes-128-cbc-sha
       - tls-ecdhe-rsa-with-aes-256-cbc-sha
       - tls-ecdhe-ecdsa-with-aes-128-cbc-sha256
       - tls-ecdhe-rsa-with-aes-128-cbc-sha256
       - tls-ecdhe-rsa-with-aes-128-gcm-sha256
       - tls-ecdhe-ecdsa-with-aes-128-gcm-sha256
       - tls-ecdhe-rsa-with-aes-256-gcm-sha384
       - tls-ecdhe-ecdsa-with-aes-256-gcm-sha384
       - tls-ecdhe-rsa-with-chacha20-poly1305
       - tls-ecdhe-ecdsa-with-chacha20-poly1305
 
 
# This section configures the 'auth service':
auth_service:
    # Turns 'auth' role on. Default is 'yes'
    enabled: yes
 
    # A cluster name is used as part of a signature in certificates
    # generated by this CA.
    #
    # We strongly recommend to explicitly set it to something meaningful as it
    # becomes important when configuring trust between multiple clusters.
    #
    # By default an automatically generated name is used (not recommended)
    #
    # IMPORTANT: if you change cluster_name, it will invalidate all generated
    # certificates and keys (may need to wipe out /var/lib/teleport directory)
    cluster_name: "remote"
 
    authentication:
        # default authentication type. possible values are 'local', 'oidc' and 'saml'
        # only local authentication (Teleport's own user DB) is supported in the open
        # source version
        type: local
        # second_factor can be off, otp, or u2f
        second_factor: otp
        # this section is used if second_factor is set to 'u2f'
        u2f:
            # app_id must point to the URL of the Teleport Web UI (proxy) accessible
            # by the end users
            app_id: https://localhost:3080
            # facets must list all proxy servers if there are more than one deployed
            facets:
            - https://localhost:3080
 
    # IP and the port to bind to. Other Teleport nodes will be connecting to
    # this port (AKA "Auth API" or "Cluster API") to validate client
    # certificates
    listen_addr: OFFICE_Private_IP:3025
 
    # The optional DNS name the auth server if located behind a load balancer.
    # (see public_addr section below)
#    public_addr: teleport.example.com:3025
 
    # Pre-defined tokens for adding new nodes to a cluster. Each token specifies
    # the role a new node will be allowed to assume. The more secure way to
    # add nodes is to use `ttl node add --ttl` command to generate auto-expiring
    # tokens.
    #
    # We recommend to use tools like `pwgen` to generate sufficiently random
    # tokens of 32+ byte length.
    tokens:
        - "proxy,node:xxxxx"
        - "auth:yyyy"
 
    # Optional setting for configuring session recording. Possible values are:
    #    "node"  : sessions will be recorded on the node level  (the default)
    #    "proxy" : recording on the proxy level, see "recording proxy mode" section.
    #    "off"   : session recording is turned off
    session_recording: "node"
 
    # This setting determines if a Teleport proxy performs strict host key checks.
    # Only applicable if session_recording=proxy, see "recording proxy mode" for details.
    proxy_checks_host_keys: yes
 
    # Determines if SSH sessions to cluster nodes are forcefully terminated
    # after no activity from a client (idle client).
    # Examples: "30m", "1h" or "1h30m"
    client_idle_timeout: never
 
    # Determines if the clients will be forcefully disconnected when their
    # certificates expire in the middle of an active SSH session. (default is 'no')
    disconnect_expired_cert: no
 
    # License file to start auth server with. Note that this setting is ignored
    # in open-source Teleport and is required only for Teleport Pro, Business
    # and Enterprise subscription plans.
    #
    # The path can be either absolute or relative to the configured `data_dir`
    # and should point to the license file obtained from Teleport Download Portal.
    #
    # If not set, by default Teleport will look for the `license.pem` file in
    # the configured `data_dir`.
    license_file: /var/lib/teleport/license.pem
 
    # DEPRECATED in Teleport 3.2 (moved to proxy_service section)
#    kubeconfig_file: /home/ubuntu/.kube/config
 
# This section configures the 'node service':
ssh_service:
    # Turns 'ssh' role on. Default is 'yes'
    enabled: yes
 
    # IP and the port for SSH service to bind to.
    listen_addr: OFFICE_Private_IP:3022
 
    # The optional public address the SSH service. This is useful if administrators
    # want to allow users to connect to nodes directly, bypassing a Teleport proxy
    # (see public_addr section below)
#    public_addr: teleport.example.com:3022
 
    # See explanation of labels in "Labeling Nodes" section below
    labels:
        role: master
        type: postgres
 
    # List of the commands to periodically execute. Their output will be used as node labels.
    # See "Labeling Nodes" section below for more information and more examples.
    commands:
    # this command will add a label 'arch=x86_64' to a node
    - name: arch
      command: ['/bin/uname', '-p']
      period: 1h0m0s
 
    # enables reading ~/.tsh/environment before creating a session. by default
    # set to false, can be set true here or as a command line flag.
    permit_user_env: false
 
    # configures PAM integration. see below for more details.
    pam:
        enabled: no
        service_name: teleport
 
# This section configures the 'proxy service'
proxy_service:
    # Turns 'proxy' role on. Default is 'yes'
    enabled: yes
 
    # SSH forwarding/proxy address. Command line (CLI) clients always begin their
    # SSH sessions by connecting to this port
    listen_addr: OFFICE_Private_IP:3023
 
    # Reverse tunnel listening address. An auth server (CA) can establish an
    # outbound (from behind the firewall) connection to this address.
    # This will allow users of the outside CA to connect to behind-the-firewall
    # nodes.
    tunnel_listen_addr: OFFICE_Private_IP:3024
 
    # The HTTPS listen address to serve the Web UI and also to authenticate the
    # command line (CLI) users via password+HOTP
    web_listen_addr: OFFICE_Private_IP:3080
 
    # The DNS name the proxy HTTPS endpoint as accessible by cluster users.
    # Defaults to the proxy's hostname if not specified. If running multiple
    # proxies behind a load balancer, this name must point to the load balancer
    # (see public_addr section below)
#    public_addr: teleport.example.com:3080
 
    # The DNS name of the proxy SSH endpoint as accessible by cluster clients.
    # Defaults to the proxy's hostname if not specified. If running multiple proxies
    # behind a load balancer, this name must point to the load balancer.
    # Use a TCP load balancer because this port uses SSH protocol.
#    ssh_public_addr: teleport.example.com:3023
 
    # TLS certificate for the HTTPS connection. Configuring these properly is
    # critical for Teleport security.
    https_key_file: /var/lib/teleport/webproxy_key.pem
    https_cert_file: /var/lib/teleport/webproxy_cert.pem
 
    # This section configures the Kubernetes proxy service
    kubernetes:
        # Turns 'kubernetes' proxy on. Default is 'no'
        enabled: no
 
        # Kubernetes proxy listen address.
        listen_addr: OFFICE_Private_IP:3026
 
        # The DNS name of the Kubernetes proxy server that is accessible by cluster clients.
        # If running multiple proxies behind  a load balancer, this name must point to the
        # load balancer.
#        public_addr: ['teleport.example.com:3026']
 
        # This setting is not required if the Teleport proxy service is
        # deployed inside a Kubernetes cluster. Otherwise, Teleport proxy
        # will use the credentials from this file:
#        kubeconfig_file: /home/ubuntu/.kube/config