N950 Firmware Upload Log

N950 Firmware Upload Log

brunql@brunql-desktop:~$ sudo ./Linux_OCF_34-2_EMMC_RM680-OEM1-916.bin 
[sudo] password for brunql: 

This is OneClickFlasher for release 34-2
 - it will erase previous EMMC from the device
 - install the RM680 OEM image
 - install the EMMC RM680 content

Extracting the archive from OneClickFlasher ...
Extracting started at 20:11:52
Extracting finished at 20:12:06

Running Installer

Please make sure your device is properly powered OFF prior to
connecting the USB cable.
You can power your device off by holding down the power button
for 8+ seconds.
Flashing your device will erase all data and reset the device
back to factory state.
Please make sure you have backups of your data before proceeding
with flashing.
Depending on amount of data to be securely erased, the erasing may
take as long as 30 minutes until the flashing starts.

Please, be patient.

Check first that device is powered OFF and then connect USB cable.

Start with erasing previous eMMC ... 20:12:07

flasher 3.12.0 (Jun 30 2011) Harmattan

Picked ape-algo from a FIASCO file
Suitable USB interface (bootloader/phonet) not found, waiting...
USB device found at bus 001, device address 016.
Device identifier: 357881040019459 (SN: N/A)
Found device RM-680, hardware revision 1124
NOLO version 2.0.37
Version of 'sw-release': DFL61_HARMATTAN_1.2011.22-6_PR_RM680
Sending ape-algo image (7020 kB)...
100% (7020 of 7020 kB, avg. 27857 kB/s)
Suitable USB interface (phonet) not found, waiting...
USB device found at bus 001, device address 017.
Device identifier: 5A5541303331343134 (SN: ZUA031414)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.5.26
Found product RM-680 rev. 1124
Server implements softupd protocol version 1.8

Battery level 58 %, continuing.
Erasing, this may take a while.
Erase done.
Success

Erasing finished at 20:32:41

Flashing image and eMMC ...
Flashing started at 20:32:41

flasher 3.12.0 (Jun 30 2011) Harmattan

USB device found at bus 001, device address 017.
Device identifier: 5A5541303331343134 (SN: ZUA031414)
Raw data transfer EP found at EP2.
Ping attempt 1 (250 ms)
Server application: 1.5.26
Found product RM-680 rev. 1124
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_1.2011.34-2_PR_RM680
Image moslo not present
Image tar skipped
Image config skipped

Battery level 64 %, continuing.

    image        [state    progress         transfer     flash speed]
---------------------------------------------------------------------
[x] cert-sw      [finished   100 %       1 /       1 kB      NA     ]
[x] cmt-2nd      [finished   100 %      95 /      95 kB      NA     ]
[x] cmt-algo     [finished   100 %     789 /     789 kB      NA     ]
[x] cmt-mcusw    [finished   100 %    6008 /    6008 kB    2948 kB/s]
[x] xloader      [finished   100 %      23 /      23 kB      NA     ]
[x] secondary    [finished   100 %      88 /      88 kB      NA     ]
[x] kernel       [finished   100 %    2708 /    2708 kB    1846 kB/s]
[x] rootfs       [finished   100 %  326205 /  326205 kB    7396 kB/s]
[x] mmc          [finished   100 %  204747 /  204747 kB   17203 kB/s]
Updating SW release
Success

Flashing finished at 20:33:50

Press Enter to exit
Unplug the USB cable from the device to boot new flashed image ...