Diff on bugfix-2.0.* branch of Marlin for X5SA. It stops extruding for some reason.

x5sa.diff

diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 9d1f7862b..f131371f5 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -21,6 +21,8 @@
  */
 #pragma once
 
+#define CONFIG_EXAMPLES_DIR "Tronxy/X5SA"
+
 /**
  * Configuration.h
  *
@@ -71,7 +73,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "cab404" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -104,13 +106,13 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT 0
+#define SERIAL_PORT 1
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-//#define SERIAL_PORT_2 -1
+#define SERIAL_PORT_2 3
 
 /**
  * This setting determines the communication speed of the printer.
@@ -128,11 +130,11 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_CHITU3D_V6
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#define CUSTOM_MACHINE_NAME "GreenCube"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -424,7 +426,7 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 
@@ -610,7 +612,7 @@
 
 // Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
 // either in the usual order or reversed
-//#define COREXY
+#define COREXY
 //#define COREXZ
 //#define COREYZ
 //#define COREYX
@@ -634,7 +636,7 @@
 //#define USE_ZMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
-#define ENDSTOPPULLUPS
+//#define ENDSTOPPULLUPS
 #if DISABLED(ENDSTOPPULLUPS)
   // Disable ENDSTOPPULLUPS to set pullups individually
   //#define ENDSTOPPULLUP_XMAX
@@ -660,13 +662,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
 #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -684,15 +686,15 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-//#define X_DRIVER_TYPE  A4988
-//#define Y_DRIVER_TYPE  A4988
-//#define Z_DRIVER_TYPE  A4988
+#define X_DRIVER_TYPE  TMC2208_STANDALONE
+#define Y_DRIVER_TYPE  TMC2208_STANDALONE
+#define Z_DRIVER_TYPE  TMC2208_STANDALONE
 //#define X2_DRIVER_TYPE A4988
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
 //#define Z3_DRIVER_TYPE A4988
 //#define Z4_DRIVER_TYPE A4988
-//#define E0_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE TMC2208_STANDALONE
 //#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
@@ -747,7 +749,9 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 4000, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 160, 160, 800, 185.22 }
+//TITAN EXTRUDER:
+//#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 92.6 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -767,7 +771,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 1500, 1500, 100, 5000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -782,9 +786,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_ACCELERATION          1500    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1500    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   1500    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk limits (mm/s)
@@ -831,7 +835,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+// #define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -889,7 +893,7 @@
  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  *   (e.g., an inductive probe or a nozzle-based probe-switch.)
  */
-//#define FIX_MOUNTED_PROBE
+#define FIX_MOUNTED_PROBE
 
 /**
  * Use the nozzle as the probe, as with a conductive
@@ -993,11 +997,11 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -40, 0, 0 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-#define PROBING_MARGIN 10
+#define PROBING_MARGIN 50
 
 // X and Y axis travel speed (mm/m) between probes
 #define XY_PROBE_SPEED 8000
@@ -1046,7 +1050,7 @@
 #define Z_PROBE_OFFSET_RANGE_MAX 20
 
 // Enable the M48 repeatability test to test probe accuracy
-//#define Z_MIN_PROBE_REPEATABILITY_TEST
+#define Z_MIN_PROBE_REPEATABILITY_TEST
 
 // Before deploy/stow pause for user confirmation
 //#define PAUSE_BEFORE_DEPLOY_STOW
@@ -1093,7 +1097,7 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
+#define INVERT_X_DIR true
 #define INVERT_Y_DIR true
 #define INVERT_Z_DIR false
 
@@ -1115,7 +1119,7 @@
 
 //#define UNKNOWN_Z_NO_RAISE      // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 10        // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                                   // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
 
 //#define Z_AFTER_HOMING  10      // (mm) Height to move to after homing Z
@@ -1129,8 +1133,8 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+#define X_BED_SIZE 330
+#define Y_BED_SIZE 330
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS 0
@@ -1138,7 +1142,7 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#define Z_MAX_POS 400
 
 /**
  * Software Endstops
@@ -1176,11 +1180,11 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_STATE     LOW   // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
+  #define FIL_RUNOUT_STATE     HIGH  // Pin state indicating that filament is NOT present.
+  //#define FIL_RUNOUT_PULLUP        // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
@@ -1241,14 +1245,14 @@
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
+#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable
  * this option to have G28 restore the prior leveling state.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 
 /**
  * Enable detailed logging of G28, G29, M48, etc.
@@ -1287,7 +1291,7 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 4
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1317,10 +1321,10 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
-  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+  #define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
 
   #define MESH_INSET 1              // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
+  #define GRID_MAX_POINTS_X 4      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
@@ -1336,7 +1340,7 @@
   //===========================================================================
 
   #define MESH_INSET 10          // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 3    // Don't use more than 7 points per axis, implementation limited.
+  #define GRID_MAX_POINTS_X 10   // Don't use more than 7 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
@@ -1347,7 +1351,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
@@ -1356,7 +1360,7 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1391,7 +1395,7 @@
 // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
 // - Prevent Z homing when the Z probe is outside bed area.
 //
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -1477,12 +1481,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS       // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1510,12 +1514,12 @@
 // Preheat Constants
 #define PREHEAT_1_LABEL       "PLA"
 #define PREHEAT_1_TEMP_HOTEND 180
-#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_TEMP_BED     50
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
 #define PREHEAT_2_TEMP_HOTEND 240
-#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_TEMP_BED    90
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 /**
@@ -1529,7 +1533,7 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
@@ -1605,10 +1609,6 @@
 
   // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
   //#define NOZZLE_CLEAN_NO_Z
-
-  // Explicit wipe G-code script applies to a G12 with no arguments.
-  //#define WIPE_SEQUENCE_COMMANDS "G1 X-17 Y25 Z10 F4000\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X-10.0 Y-9.0"
-
 #endif
 
 /**
@@ -1682,7 +1682,7 @@
  *
  * :['JAPANESE', 'WESTERN', 'CYRILLIC']
  */
-#define DISPLAY_CHARSET_HD44780 JAPANESE
+#define DISPLAY_CHARSET_HD44780 CYRILLIC
 
 /**
  * Info Screen Style (0:Classic, 1:Prusa)
@@ -1698,7 +1698,7 @@
  * you must uncomment the following option or it won't work.
  *
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: SPI SPEED
@@ -1715,7 +1715,7 @@
  *
  * Use CRC checks and retries on the SD communication.
  */
-//#define SD_CHECK_AND_RETRY
+#define SD_CHECK_AND_RETRY
 
 /**
  * LCD Menu Items
@@ -1786,7 +1786,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -2176,7 +2176,7 @@
 // FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, REXYZ A1, etc.)
 // Upscaled 128x64 Marlin UI
 //
-//#define FSMC_GRAPHICAL_TFT
+#define FSMC_GRAPHICAL_TFT
 
 //
 // TFT LVGL UI
@@ -2206,19 +2206,30 @@
 //
 // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
 //
-//#define TOUCH_SCREEN
+
+#define TOUCH_SCREEN
+//DONE BY CHITU BOARD
 #if ENABLED(TOUCH_SCREEN)
+  #define TOUCH_SCREEN_CALIBRATION
   #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
   #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
 
-  #define TOUCH_SCREEN_CALIBRATION
-
-  //#define XPT2046_X_CALIBRATION 12316
-  //#define XPT2046_Y_CALIBRATION -8981
-  //#define XPT2046_X_OFFSET        -43
-  //#define XPT2046_Y_OFFSET        257
+  #define XPT2046_X_CALIBRATION  -12316
+  #define XPT2046_Y_CALIBRATION   8981
+  #define XPT2046_X_OFFSET        340
+  #define XPT2046_Y_OFFSET        -20
 #endif
 
+// Change colors
+// some colors are predefined, see /src/lcd/dogm/u8g_dev_tft_480~.cpp Line 160
+// or use 16bit color (e.g. 0x0000 = black, 0xFFE0 = yellow)
+// see https://ee-programming-notepad.blogspot.com/2016/10/16-bit-color-generator-picker.html
+#define TFT_MARLINUI_COLOR COLOR_WHITE  // main foreground color
+#define TFT_MARLINBG_COLOR COLOR_BLACK  // background color
+#define TFT_BTCANCEL_COLOR COLOR_RED    // cancel button
+#define TFT_BTARROWS_COLOR COLOR_WHITE  // arrows up/down
+#define TFT_BTOKMENU_COLOR COLOR_GREEN  // enter button
+
 //
 // RepRapWorld REPRAPWORLD_KEYPAD v1.1
 // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
@@ -2238,7 +2249,7 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 37c997977..c26d5bbc5 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -21,6 +21,8 @@
  */
 #pragma once
 
+#define CONFIG_EXAMPLES_DIR "Tronxy/X5SA"
+
 /**
  * Configuration_adv.h
  *
@@ -371,7 +373,7 @@
  * The fan turns on automatically whenever any driver is enabled and turns
  * off (or reduces to idle speed) shortly after drivers are turned off.
  */
-//#define USE_CONTROLLER_FAN
+#define USE_CONTROLLER_FAN
 #if ENABLED(USE_CONTROLLER_FAN)
   //#define CONTROLLER_FAN_PIN -1        // Set a custom pin for the controller fan
   //#define CONTROLLER_FAN_USE_Z_ONLY    // With this option only the Z axis is considered
@@ -450,7 +452,7 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
+#define E0_AUTO_FAN_PIN FAN_PIN_2
 #define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
@@ -1200,7 +1202,7 @@
   #endif
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
   //#define SCROLL_LONG_FILENAMES
@@ -1553,17 +1555,17 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
-  #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
+  #define BABYSTEP_MULTIPLICATOR_Z  10       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
@@ -1574,9 +1576,9 @@
     #endif
   #endif
 
-  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+  #define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
     //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
@@ -1600,10 +1602,10 @@
  *
  * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  */
-//#define LIN_ADVANCE
+#define LIN_ADVANCE
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.22    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0       // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
   //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif
@@ -2037,7 +2039,7 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2407,7 +2409,7 @@
    */
   #define STEALTHCHOP_XY
   #define STEALTHCHOP_Z
-  #define STEALTHCHOP_E
+  //#define STEALTHCHOP_E
 
   /**
    * Optimize spreadCycle chopper parameters by using predefined parameter sets
@@ -2424,7 +2426,7 @@
    * Define you own with
    * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
    */
-  #define CHOPPER_TIMING CHOPPER_DEFAULT_12V
+  #define CHOPPER_TIMING CHOPPER_DEFAULT_24V
 
   /**
    * Monitor Trinamic drivers
@@ -2532,7 +2534,7 @@
    * Enable M122 debugging command for TMC stepper drivers.
    * M122 S0/1 will enable continous reporting.
    */
-  //#define TMC_DEBUG
+  #define TMC_DEBUG
 
   /**
    * You can set your own advanced settings by filling in predefined functions.
@@ -3111,8 +3113,6 @@
 //#define M114_REALTIME       // Real current position based on forward kinematics
 //#define M114_LEGACY         // M114 used to synchronize on every call. Enable if needed.
 
-//#define REPORT_FAN_CHANGE   // Report the new fan speed when changed by M106 (and others)
-
 /**
  * Set the number of proportional font spaces required to fill up a typical character space.
  * This can help to better align the output of commands like `G29 O` Mesh Output.