Model: GFLT100 HW: 2.0 Date: Dec. 8th 2013
UART / Serial connection (pinouts next to fiber I/O, C45, C46, J5):
WG
RB
W = RX G = TX B = GND R = VCC
115200.8.N.1 Boot = output.txt
Photos: http://imetchrischris.com/GFLT100.html
Finding serial ports on embedded systems:
Other/misc:
| HELO | |
| CPUI | |
| L1CI | |
| HELO | |
| CPUI | |
| L1CI | |
| DRAM | |
| ---- | |
| PHYS | |
| 400H | |
| PHYE | |
| DDR2 | |
| SIZ4 | |
| SIZ3 | |
| SIZ2 | |
| SIZ1 | |
| DINT | |
| USYN | |
| LSYN | |
| MFAS | |
| LMBE | |
| RACE | |
| PASS | |
| ---- | |
| ZBSS | |
| CODE | |
| DATA | |
| L12F | |
| MAIN | |
| CFE version 1.0.38-114.170.13 for BCM96818 (32bit,SP,BE) | |
| Build Date: Tue Mar 5 13:46:08 CST 2013 (tempest@POWERSERVER2) | |
| Copyright (C) 2000-2011 Broadcom Corporation. | |
| HS Serial flash device: name MX25L128, id 0xc218 size 16384KB | |
| Total Flash size: 16384K with 4096 sectors | |
| Flash not used for Auxillary File System | |
| Chip ID: BCM6812R_A1, MIPS: 360MHz, DDR: 300MHz, Bus: 180MHz | |
| Main Thread: TP0 | |
| Memory Test(DDR double refresh rate) Passed | |
| Total Memory: 67108864 bytes (64MB) | |
| Boot Address: 0xb8000000 | |
| Board IP address : 192.168.1.1 | |
| Host IP address : 192.168.1.100 | |
| Gateway IP address : | |
| Run from flash/host (f/h) : f | |
| Default host run file name : vmlinux | |
| Default host flash file name : bcmXO572_6818B_cfe_fs_kernel | |
| Boot delay (0-9 seconds) : 1 | |
| Boot image (0=latest, 1=previous) : 0 | |
| Board Id (0-6) : XO572 | |
| Number of MAC Addresses (1-32) : 1 | |
| Base MAC Address : f8:8f:ca:01:ff:3c | |
| PSI Size (1-64) KBytes : 24 | |
| Enable Backup PSI [0|1] : 0 | |
| System Log Size (0-256) KBytes : 0 | |
| Auxillary File System Size Percent: 0 | |
| Main Thread Number [0|1] : 0 | |
| GPON Serial Number : "GFAA35004734" | |
| GPON Password : "2222222222" | |
| Hardware Version : 2.0 | |
| Mindspeed M02098 detected! change Vbr 43 -> 41. | |
| *** Press C for lazer driver calibration, | |
| *** Any other key to stop auto run (1 seconds) *** | |
| Auto run second count down: 0 | |
| Booting from latest image (0xb8020000) ... | |
| Code Address: 0x80010000, Entry Address: 0x8023f800 | |
| Decompression OK! | |
| Entry at 0x8023f800 | |
| Closing network. | |
| Disabling Switch ports. | |
| Flushing Receive Buffers... | |
| 0 buffers found. | |
| Closing DMA Channels. | |
| Starting program at 0x8023f800 | |
| Linux version 2.6.30 (matt@POWERSERVER2) (gcc version 4.4.2 (Buildroot 2010.02-g | |
| it) ) #1 SMP PREEMPT Mon Feb 10 09:20:17 CST 2014 | |
| HS Serial flash device: name MX25L128, id 0xc218 size 16384KB | |
| XO572 prom init | |
| CPU revision is: 0002a080 (Broadcom4350) | |
| Determined physical RAM map: | |
| memory: 04000000 @ 00000000 (usable) | |
| Zone PFN ranges: | |
| DMA 0x00000000 -> 0x00001000 | |
| Normal 0x00001000 -> 0x00004000 | |
| Movable zone start PFN for each node | |
| early_node_map[1] active PFN ranges | |
| 0: 0x00000000 -> 0x00004000 | |
| On node 0 totalpages: 16384 | |
| free_area_init_node: node 0, pgdat 802befb0, node_mem_map 81000000 | |
| DMA zone: 32 pages used for memmap | |
| DMA zone: 0 pages reserved | |
| DMA zone: 4064 pages, LIFO batch:0 | |
| Normal zone: 96 pages used for memmap | |
| Normal zone: 12192 pages, LIFO batch:1 | |
| Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 | |
| Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 | |
| wait instruction: enabled | |
| Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. | |
| Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes | |
| NR_IRQS:128 | |
| PID hash table entries: 256 (order: 8, 1024 bytes) | |
| console [ttyS0] enabled | |
| Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) | |
| Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) | |
| Allocating memory for GPON DDR offload buffers. | |
| Allocated GPON DDRO memory - Address=0x81095400 SIZE=8192KB | |
| Memory: 53528k/65536k available (2268k kernel code, 11988k reserved, 497k data, | |
| 136k init, 0k highmem) | |
| Calibrating delay loop... 358.40 BogoMIPS (lpj=179200) | |
| Mount-cache hash table entries: 512 | |
| --Kernel Config-- | |
| SMP=1 | |
| PREEMPT=1 | |
| DEBUG_SPINLOCK=0 | |
| DEBUG_MUTEXES=0 | |
| Broadcom Logger v0.1 Feb 10 2014 09:17:48 | |
| CPU revision is: 0002a080 (Broadcom4350) | |
| Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. | |
| Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes | |
| Calibrating delay loop... 362.49 BogoMIPS (lpj=181248) | |
| Brought up 2 CPUs | |
| net_namespace: 800 bytes | |
| NET: Registered protocol family 16 | |
| Total Flash size: 16384K with 4096 sectors | |
| Flash not used for Auxillary File System | |
| registering PCI controller with io_map_base unset | |
| registering PCI controller with io_map_base unset | |
| bio: create slab <bio-0> at 0 | |
| pci 0000:01:00.0: PME# supported from D0 D3hot | |
| pci 0000:01:00.0: PME# disabled | |
| pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 | |
| pci 0000:01:00.0: IO window: disabled | |
| pci 0000:01:00.0: MEM window: disabled | |
| pci 0000:01:00.0: PREFETCH window: disabled | |
| PCI: Setting latency timer of device 0000:01:00.0 to 64 | |
| BLOG v3.0 Initialized | |
| BLOG Rule v1.0 Initialized | |
| Broadcom IQoS v0.1 Feb 10 2014 09:19:52 initialized | |
| Broadcom GBPM v0.1 Feb 10 2014 09:19:52 initialized | |
| NET: Registered protocol family 8 | |
| NET: Registered protocol family 20 | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | |
| TCP established hash table entries: 2048 (order: 2, 16384 bytes) | |
| TCP bind hash table entries: 2048 (order: 2, 16384 bytes) | |
| TCP: Hash tables configured (established 2048 bind 2048) | |
| TCP reno registered | |
| NET: Registered protocol family 1 | |
| squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| squashfs: version 4.0 with LZMA457 ported by BRCM | |
| msgmni has been set to 104 | |
| io scheduler noop registered (default) | |
| pcieport-driver 0000:01:00.0: device [14e4:6818] has invalid IRQ; check vendor B | |
| IOS | |
| PCI: Setting latency timer of device 0000:01:00.0 to 64 | |
| PPP generic driver version 2.4.2 | |
| PPP Deflate Compression module registered | |
| PPP BSD Compression module registered | |
| NET: Registered protocol family 24 | |
| bcm963xx_mtd driver v2.0 | |
| File system address: 0xb8020100 | |
| Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8020100,3584000] | |
| i2c /dev entries driver | |
| brcmboard: brcm_board_init entry | |
| PCIe: No device found - Powering down | |
| brcm_board_init: isShared=0, rstToDflt_irq=4 | |
| Serial: BCM63XX driver $Revision: 3.00 $ | |
| Magic SysRq enabled (type ^ h for list of supported commands) | |
| ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX | |
| ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX | |
| Total # RxBds=1200 | |
| bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized | |
| bcmPktDma_init: Broadcom Packet DMA Library initialized | |
| TCP cubic registered | |
| NET: Registered protocol family 10 | |
| IPv6 over IPv4 tunneling driver | |
| NET: Registered protocol family 17 | |
| Initializing MCPD Module | |
| Ebtables v2.0 registered | |
| ebt_time registered | |
| ebt_ftos registered | |
| 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> | |
| All bugs added by David S. Miller <davem@redhat.com> | |
| VFS: Mounted root (squashfs filesystem) readonly on device 31:0. | |
| Freeing unused kernel memory: 136k freed | |
| init started: BusyBox v1.17.2 (2014-02-10 09:23:57 CST) | |
| starting pid 133, tty '': '/etc/init.d/rcS' | |
| mount: mounting sysfs on /sys failed: No such device | |
| starting pid 138, tty '': '-/bin/sh' | |
| BusyBox v1.17.2 (2014-02-10 09:23:57 CST) built-in shell (ash) | |
| Enter 'help' for a list of built-in commands. | |
| Loading drivers and kernel modules... | |
| chipinfo: module license 'proprietary' taints kernel. | |
| Disabling lock debugging due to kernel taint | |
| brcmchipinfo: brcm_chipinfo_init entry | |
| Broadcom Ingress QoS Module Char Driver v0.1 Feb 10 2014 09:19:05 Registered<24 | |
| 3> | |
| Broadcom Ingress QoS ver 0.1 initialized | |
| BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers | |
| =4730, buf size=2128 | |
| Broadcom BPM Module Char Driver v0.1 Feb 10 2014 09:18:00 Registered<244> | |
| [NTC bpm] bpm_set_status: BPM status : enabled | |
| NBUFF v1.0 Initialized | |
| Initialized fcache state | |
| Broadcom Packet Flow Cache Char Driver v2.2 Feb 10 2014 09:19:06 Registered<242 | |
| > | |
| Created Proc FS /procfs/fcache | |
| Broadcom Packet Flow Cache registered with netdev chain | |
| Broadcom Packet Flow Cache learning via BLOG enabled. | |
| Constructed Broadcom Packet Flow Cache v2.2 Feb 10 2014 09:19:06 | |
| [NTC pktcmf] cmfConstruct: Broadcom Packet [6811-A1] v0.1 Sep 25 2012 18:13:46 | |
| Loaded | |
| [NTC pktcmf] pktCmfDisableSwitch: Checking Switch Ports | |
| IRQ 8/brcm_8: IRQF_DISABLED is not guaranteed on shared IRQs | |
| [NTC cmfffe] pktCmfFfe_construct: Initialized FFE Layer | |
| [NTC cmfhw] pktCmfHwReset: Reset to 0 all CMF HW registers and RAMs. | |
| [NTC cmfhw] pktCmfHwMiss: Set FIR<512..639> MISS to DROP <0x00000000 0x08000000 | |
| 0x00000000 0x00000000 0x00000000>. | |
| [NTC cmfhw] pktCmfHwConstruct: Reset and initialized CMF HW Layer. | |
| [NTC cmfhwif] pktCmfHwIfInit: Initialized HWIF layer. | |
| [NTC cmfhal] pktCmfHalInit: Initialized HAL layer. | |
| [NTC pktcmf] pktCmfParser_construct: Initialized Packet CMF Parser | |
| [NTC cmfnat] pktCmfNatReset: Reset CMF NAT layer. | |
| [NTC cmfnat] pktCmfNatConstruct: Reset and initialized CMF NAT Layer. | |
| [NTC pktcmf] pktCmfDrv_construct: Broadcom Packet Char Driver v0.1 Feb 10 2014 | |
| 09:19:06 Registered<232> | |
| chipId 0x681100A1 | |
| Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Feb 10 2014 09:18:02 | |
| Registered <241> | |
| Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 | |
| FAP Soft Reset Done | |
| 4ke Reset Done | |
| Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 | |
| FAP Soft Reset Done | |
| 4ke Reset Done | |
| FAP Debug values at 0xa2496ca0 0xa24d6ca0 | |
| Allocated FAP0 GSO Buffers (0xA24A8528) : 1048576 bytes @ 0xA2500000 | |
| Allocated FAP1 GSO Buffers (0xA24E8528) : 1048576 bytes @ 0xA2600000 | |
| Allocated FAP0 TM SDRAM Queue Storage (a24a852c) : 341376 bytes @ a2700000 | |
| Allocated FAP1 TM SDRAM Queue Storage (a24e852c) : 341376 bytes @ a2780000 | |
| [NTC fapProto] fapReset : Reset FAP Protocol layer | |
| bcmPktDma_bind: FAP Driver binding successfull | |
| [FAP0] GSO Buffer set to 0xA2500000 | |
| [FAP1] GSO Buffer set to 0xA2600000 | |
| [FAP0] FAP BPM Initialized. | |
| [FAP1] FAP BPM Initialized. | |
| [FAP0] FAP TM: ON | |
| [FAP1] FAP TM: ON | |
| [NTC cmfffe] pktCmfFfe_iMemWrite: FFE iMem Write: PortMask<0x2F> Instructions<84 | |
| 5> | |
| [NTC cmfffe] pktCmfFfe_iMemWrite: FFE iMem Write: PortMask<0x80> Instructions<72 | |
| 7> | |
| [NTC cmfffe] pktCmfFfe_iMemWrite: FFE iMem Write: PortMask<0x10> Instructions<10 | |
| 56> | |
| [NTC cmfffe] pktCmfFfe_iMemWrite: FFE iMem Write: PortMask<0x40> Instructions<10 | |
| 56> | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<0> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<1> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<2> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<3> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<4> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<5> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<6> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgLabels: Configured Port<7> FFE Labels | |
| [NTC cmfffe] pktCmfFfe_CfgSnoop: Configured FFE Snooping | |
| [NTC cmfffe] pktCmfFfe_CfgPatch: Patched FFE Code | |
| [NTC cmfffe] initInstMem: FFEs Enabled | |
| cmfcfg: Enabling CMF | |
| [NTC cmfhw] pktCmfHwCtxSigMiss: Set SIG MISS CTX<768..63> <0x83400200> = matchTa | |
| g<0> ffeEntryPt<0x0004>. | |
| [NTC cmfffe] ffeEnable : FFE Layer: ENABLE | |
| [NTC cmfhal] pktCmfHalEnable: Enabled HAL layer. | |
| [NTC pktcmf] parserIf_Enable: Parser Layer: ENABLE | |
| [NTC cmfnat] pktCmfNatEnable: Enabled CMF to PktFlow binding. | |
| cmfcfg: Setting Default Flow Miss action to PASS | |
| [NTC cmfhw] pktCmfHwMiss: Set FIR<512..639> MISS to NONE <0x00000000 0x00000000 | |
| 0x00000000 0x00000000 0x00000000>. | |
| cmfcfg: Setting UNI Port Global Default ASPF actions to ACCEPT | |
| Broadcom BCM6812R_A1 Ethernet Network Device v0.1 Feb 10 2014 09:19:20 | |
| bcmPktDma_psmAlloc channel (0 / 1)!! | |
| bcmPktDma_psmAlloc size=32 totalSize=6400)!! | |
| fapDrv_psmAlloc: fapIdx=0, size: 6400, offset=b0820030 bytes remaining 5408 | |
| ETH Init: Ch:0 - 200 tx BDs at 0xb0820030 | |
| bcmPktDma_psmAlloc channel (1 / 2)!! | |
| bcmPktDma_psmAlloc size=32 totalSize=6400)!! | |
| fapDrv_psmAlloc: fapIdx=1, size: 6400, offset=b0a20030 bytes remaining 5408 | |
| ETH Init: Ch:1 - 200 tx BDs at 0xb0a20030 | |
| fapDrv_psmAlloc: wastage 8 bytes | |
| fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821930 bytes remaining 592 | |
| ETH Init: Ch:0 - 600 rx BDs at 0xb0821930 | |
| fapDrv_psmAlloc: wastage 8 bytes | |
| fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21930 bytes remaining 592 | |
| ETH Init: Ch:1 - 600 rx BDs at 0xb0a21930 | |
| dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered | |
| eth0: MAC Address: F8:8F:CA:01:FF:3C | |
| eth1: MAC Address: F8:8F:CA:01:FF:3C | |
| Broadcom PLOAM Driver version: v0.8 Feb 10 2014 09:18:54 | |
| [NTC ploamFsm] printSerialPasswd: SN=47:46:41:41:35:00:47:34 | |
| [NTC ploamFsm] printSerialPasswd: PW=32:32:32:32:32:32:32:32:32:32 | |
| [NTC ploamFsm] printBanner: EQ=0x9ea2, TO1=10000 ms, TO2=100 ms | |
| [NTC ploamFsm] printBanner: PLOAMGEMPORTMAP=0, URGENT=1, KEEP_CONFIG=1 NUM_GEM_P | |
| ORTS=128 | |
| [NTC ploam] bcm_ploamUsrCreate: ploam device bcm_ploam (major=237) created. | |
| [NTC ploamFsm] bcm_ploamCreate: GPON DDRO Total Q Size 8192 | |
| dgasp: kerSysRegisterDyingGaspHandler: gpon0 registered | |
| [NTC ploamFsm] bcm_ploamCreate: ploam driver created. | |
| Broadcom OMCI Driver (Feb 10 2014 09:18:57) | |
| [NTC ploamFsm] bcm_ploamInit: ploam driver initialized. | |
| Broadcom 802.1Q VLAN Interface, v0.1 | |
| ===== Release Version 4.12L.07 (build timestamp 140210_0920) ===== | |
| Host MIPS Clock divider pwrsaving is enabled | |
| Adaptive Voltage Scaling is now enabled | |
| Netfilter messages via NETLINK v0.30. | |
| device eth0 entered promiscuous mode | |
| ADDRCONF(NETDEV_UP): eth0: link is not ready | |
| ADDRCONF(NETDEV_UP): eth1: link is not ready | |
| A certificate with the same name already exists | |
| A certificate with the same name already exists | |
| monitor task is initialized pid= 254 | |
| Broadcom Packet CMF Daemon v0.1 (Feb 10 2014, 09:24:39) | |
| 0xB0000000 : 681100A1 | |
| [VAPD] init Vbr=43 | |
| Threshold for LD Protection Mode: | |
| --------------------------------- | |
| Bias current: 70.0 mA | |
| Modulation current: 90.0 mA | |
| --------------------------------- | |
| [XAVi BOSA Monitor Thread] spawned! | |
| Note: Loading 6816 MDK driver for 6811 chip | |
| Switch MDK: num_switches = 1 | |
| Switch MDK: unit = 0; phy_pbmp = 0x1; config_pbmp = 0x91 | |
| Switch MDK link poll thread: unit=0; phypbmp=0x1 | |
| tr69c:error:11.494:updateTr69cCfgInfo:813:could not build full path to (null) | |
| Active partition = 1, Next partition = 1 | |
| ASCII version string 1.11_GFLT100 extracted from software image 0 | |
| Hexadecimal version string 312E31315F47464C543130300000 added to software image | |
| ME 0 | |
| ASCII version string 1.10_GFLT100 extracted from software image 1 | |
| Hexadecimal version string 312E31305F47464C543130300000 added to software image | |
| ME 1 | |
| Enable all port to accept jumbo frame | |
| [NTC cmfhw] pktCmfHwMiss: Set FIR<512..639> MISS to DROP <0x00000000 0x08000000 | |
| 0x00000000 0x00000000 0x00000000>. | |
| Broadcom Packet Flow Cache learning via BLOG disabled. | |
| Broadcom GPON OMCI Stack v0.1 (Feb 10 2014, 09:24:35) | |
| OMCI message capture enabled. | |
| BCM96818 Broadband Router | |
| Login: br0: no IPv6 routers present |
Model: GFLT110 Hardware Version: Rev 2A
https://wikidevi.com/wiki/Google_Fiber_Jack_v2_(GFLT110)
setenv bootargs "${bootargs} root=rootfs0 debug=1";
sf read ${loadaddr} ${image_address} 0xE00000; bootm
Stats from GFLT operation normally sent to Google Fiber's networkbox: https://github.com/DentonGentry/gfiber-platform/blob/master/cmds/statcatcher.cc
| __ __ _ _ | |
| | \/ | __ _ _ ____ _____| | | | |
| | |\/| |/ _` | '__\ \ / / _ \ | | | |
| | | | | (_| | | \ V / __/ | | | |
| |_| |_|\__,_|_| \_/ \___|_|_| | |
| _ _ ____ _ | |
| | | | | | __ ) ___ ___ | |_ | |
| | | | |___| _ \ / _ \ / _ \| __| | |
| | |_| |___| |_) | (_) | (_) | |_ | |
| \___/ |____/ \___/ \___/ \__| | |
| ** LOADER ** | |
| U-Boot 2009.08 (Aug 04 2014 - 13:00:56) Marvell version: 4.1.2_PQ | |
| Board: GFLT110 | |
| SoC: 88F6601 A0 | |
| CPU: Marvell Feroceon (Rev 1) - LE | |
| CPU @ 400Mhz, | |
| DDR3 @ 400Mhz, TClock @ 200Mhz | |
| DRAM: 256 MB | |
| CS 0: base 0x00000000 size 256 MB | |
| Addresses 21M - 0M are saved for the U-Boot usage. | |
| SF: Enabling 4-Byte address mode | |
| SF: Detected MX25L25635E with page size 256, total 33554432 bytes | |
| SF: Enabling 4-Byte address mode | |
| SF: Detected MX25L25635E with page size 256, total 33554432 bytes | |
| SV: System variables(RW) has been loaded | |
| SV: Recovering data | |
| SV: System variables(RO) has been loaded | |
| ## SYSVAR: 'BOOT_SIDE' not found | |
| Shutting down unused interfaces: | |
| Modules Detected: | |
| GPON module detected. | |
| GE-PHY on MAC0. | |
| Net: egiga0 [PRIME], egiga1 | |
| Hit any key to stop autoboot: 0 | |
| ## Booting kernel from Legacy Image at 03000000 ... | |
| Image Name: gflt110-42.33 | |
| Created: 2015-12-06 4:10:04 UTC | |
| Image Type: ARM Linux Kernel Image (uncompressed) | |
| Data Size: 13244596 Bytes = 12.6 MB | |
| Load Address: 00008000 | |
| Entry Point: 00008000 | |
| Verifying Checksum ... OK | |
| Loading Kernel Image ... OK | |
| OK | |
| Starting kernel ... | |
| Uncompressing Linux..................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................... done, booting the kernel. | |
| [ 0.000000] Linux version 2.6.32.11 (dgentry@dgentry.mtv.corp.google.com) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC branch-4.6.3. Marvell GCC 201206-1216.caf91d97) ) #2 Sat Dec 5 20:09:59 PST 2015 | |
| [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 | |
| [ 0.000000] CPU: VIVT data cache, VIVT instruction cache | |
| [ 0.000000] Machine: Feroceon-KW2 | |
| [ 0.000000] Using UBoot passing parameters structure | |
| [ 0.000000] Memory policy: ECC disabled, Data cache writeback | |
| [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 | |
| [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:768k(loader),256k(env),128k(var1),128k(var2),128k(sysvar1),128k(sysvar2),14m(kernel0),14m(kernel1),-(user_data) root=rootfs0 console=ttyS0,115200 log_buf_len=1048576 | |
| [ 0.000000] log_buf_len: 1048576 | |
| [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) | |
| [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
| [ 0.000000] Memory: 256MB = 256MB total | |
| [ 0.000000] Memory: 240896KB available (4912K code, 2077K data, 10684K init, 0K highmem) | |
| [ 0.000000] Hierarchical RCU implementation. | |
| [ 0.000000] NR_IRQS:208 | |
| [ 0.000000] Console: colour dummy device 80x30 | |
| [ 0.000000] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656) | |
| [ 0.210000] Mount-cache hash table entries: 512 | |
| [ 0.210000] CPU: Testing write buffer coherency: ok | |
| [ 0.210000] devtmpfs: initialized | |
| [ 0.220000] NET: Registered protocol family 16 | |
| [ 0.220000] No L2-Cache. | |
| [ 0.230000] | |
| [ 0.230000] CPU Interface | |
| [ 0.230000] ------------- | |
| [ 0.230000] SDRAM_CS0 ....base 00000000, size 256MB | |
| [ 0.230000] SDRAM_CS1 ....no such | |
| [ 0.230000] SDRAM_CS2 ....no such | |
| [ 0.230000] SDRAM_CS3 ....no such | |
| [ 0.230000] DEVICE_CS0 ....no such | |
| [ 0.230000] DEVICE_CS1 ....no such | |
| [ 0.230000] DEVICE_CS2 ....no such | |
| [ 0.230000] DEVICE_CS3 ....no such | |
| [ 0.230000] PEX0_MEM ....no such | |
| [ 0.230000] PEX0_IO ....no such | |
| [ 0.230000] PEX1_MEM ....no such | |
| [ 0.230000] PEX1_IO ....no such | |
| [ 0.230000] INTER_REGS ....base f1000000, size 1MB | |
| [ 0.230000] NAND_NOR_CS ....no such | |
| [ 0.230000] SPI_CS0 ....base f6000000, size 32MB | |
| [ 0.230000] SPI_CS1 ....no such | |
| [ 0.230000] SPI_CS2 ....no such | |
| [ 0.230000] SPI_CS3 ....no such | |
| [ 0.230000] SPI_CS4 ....no such | |
| [ 0.230000] SPI_CS5 ....no such | |
| [ 0.230000] SPI_CS6 ....no such | |
| [ 0.230000] SPI_CS7 ....no such | |
| [ 0.230000] SPI_B_CS0 ....no such | |
| [ 0.230000] BOOT_ROM_CS ....no such | |
| [ 0.230000] DEV_BOOTCS ....no such | |
| [ 0.230000] CRYPT1_ENG ....no such | |
| [ 0.230000] CRYPT2_ENG ....no such | |
| [ 0.230000] PNC_BM ....base f5000000, size 1MB | |
| [ 0.230000] ETH_CTRL ....base f5100000, size 1MB | |
| [ 0.230000] PON_CTRL ....base f5200000, size 1MB | |
| [ 0.230000] NFC_CTRL ....no such | |
| [ 0.230000] | |
| [ 0.230000] Marvell Development Board (LSP Version KW2_LSP_3.3.1_p12_PQ_uPON_2.7.25_RC22)-- GFLT110 Soc: 88F6601 A0 LE | |
| [ 0.230000] | |
| [ 0.230000] Detected Tclk 200000000 and SysClk 400000000 | |
| [ 0.230000] | |
| [ 0.230000] Warning PCI-E is Powered Off | |
| [ 0.260000] bio: create slab <bio-0> at 0 | |
| [ 0.260000] vgaarb: loaded | |
| [ 0.270000] Switching to clocksource kw_clocksource | |
| [ 0.270000] NET: Registered protocol family 2 | |
| [ 0.270000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| [ 0.270000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
| [ 0.270000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| [ 0.270000] TCP: Hash tables configured (established 8192 bind 8192) | |
| [ 0.270000] TCP reno registered | |
| [ 0.270000] NET: Registered protocol family 1 | |
| [ 0.280000] RPC: Registered udp transport module. | |
| [ 0.280000] RPC: Registered tcp transport module. | |
| [ 0.280000] RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| [ 3.520000] = PON Module Init = | |
| [ 3.540000] = PON Module Init ended successfully = | |
| [ 3.540000] (tpm_init_ioctl_mempools:3574) init tpm_ioctl_mpools.mpool_s, number_of_entries=21, entry_size=268 pool=0xcf8a2000 | |
| [ 3.540000] (tpm_init_ioctl_mempools:3604) init tpm_ioctl_mpools.mpool_m, number_of_entries=2, entry_size=836 pool=0xcd58e800 | |
| [ 3.540000] (tpm_init_ioctl_mempools:3634) init tpm_ioctl_mpools.mpool_l, number_of_entries=2, entry_size=1616 pool=0xcf81f000 | |
| [ 3.540000] (tpm_init_ioctl_mempools:3664) init tpm_ioctl_mpools.mpool_h, number_of_entries=1, entry_size=3620 pool=0xcd58f000 | |
| [ 3.570000] = SW Module SYS FS Init ended successfully = | |
| [ 3.570000] init_tpm_pkt_frwd_db: Clearing DB | |
| [ 3.570000] init_tpm_vlan_db: Clearing DB | |
| [ 3.570000] init_tpm_mod_db: Clearing DB | |
| [ 3.570000] init_tpm_l2_key_db: Clearing DB | |
| [ 3.570000] init_tpm_l2_rule_db: Clearing DB | |
| [ 3.570000] init_tpm_l3_key_db: Clearing DB | |
| [ 3.570000] init_tpm_ipv4_key_db: Clearing DB | |
| [ 3.570000] init_tpm_ipv6_key_db: Clearing DB | |
| [ 3.570000] init_tpm_ipv6_dip_key_db: Clearing DB | |
| [ 3.570000] init_tpm_ipv6_gen_key_db: Clearing DB | |
| [ 3.570000] init_tpm_ipv6_l4_ports_key_db: Clearing DB | |
| [ 3.580000] = SW Module SYS FS Init for tpm ended successfully = | |
| [ 3.580000] = TPM Module Init ended successfully = | |
| [ 3.600000] Registered led device: sys-blue | |
| [ 3.610000] Registered led device: sys-red | |
| [ 3.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| [ 3.650000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. | |
| [ 3.650000] msgmni has been set to 471 | |
| [ 3.680000] alg: No test for stdrng (krng) | |
| [ 3.680000] io scheduler noop registered | |
| [ 3.680000] io scheduler anticipatory registered (default) | |
| [ 6.490000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled | |
| [ 6.780000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | |
| [ 6.790000] console [ttyS0] enabled | |
| [ 7.000000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | |
| [ 7.660000] brd: module loaded | |
| [ 8.070000] loop: module loaded | |
| [ 8.160000] mvSFlashInit: Enabling 4-Byte address mode | |
| [ 8.160000] SPI Serial flash detected @ 0xf6000000, 32768KB (512sec x 64KB) | |
| [ 8.170000] 9 cmdlinepart partitions found on MTD device spi_flash | |
| [ 8.180000] Creating 9 MTD partitions on "spi_flash": | |
| [ 8.180000] 0x000000000000-0x0000000c0000 : "loader" | |
| [ 8.560000] 0x0000000c0000-0x000000100000 : "env" | |
| [ 8.630000] 0x000000100000-0x000000120000 : "var1" | |
| [ 8.660000] 0x000000120000-0x000000140000 : "var2" | |
| [ 8.690000] 0x000000140000-0x000000160000 : "sysvar1" | |
| [ 8.720000] 0x000000160000-0x000000180000 : "sysvar2" | |
| [ 8.750000] 0x000000180000-0x000000f80000 : "kernel0" | |
| [ 8.780000] 0x000000f80000-0x000001d80000 : "kernel1" | |
| [ 8.810000] 0x000001d80000-0x000002000000 : "user_data" | |
| [ 8.860000] mv_eth_probe: port_mask=0x7, cpu_mask=0x1 | |
| [ 8.860000] 0 - Base 0x00000000 , Size = 0x10000000. | |
| [ 8.870000] 12 - Base 0xf1000000 , Size = 0x00100000. | |
| [ 8.870000] 14 - Base 0xf6000000 , Size = 0x02000000. | |
| [ 8.880000] 27 - Base 0xf5000000 , Size = 0x00100000. | |
| [ 8.880000] 28 - Base 0xf5100000 , Size = 0x00100000. | |
| [ 8.890000] 29 - Base 0xf5200000 , Size = 0x00100000. | |
| [ 8.890000] mvPncVirtBase = 0xd0c00000 | |
| [ 8.900000] o 3 Giga ports supported | |
| [ 8.900000] o Giga PON port is #2: - 8 TCONTs supported | |
| [ 8.910000] o SKB recycle supported (Enabled) | |
| [ 8.910000] o NETA acceleration mode 4 | |
| [ 8.910000] o PnC supported (Enabled) | |
| [ 8.920000] o HWF supported | |
| [ 8.920000] o PMT supported | |
| [ 8.920000] o RX Queue support: 8 Queues * 128 Descriptors | |
| [ 8.930000] o TX Queue support: 8 Queues * 3072 Descriptors | |
| [ 8.940000] o Receive checksum offload supported | |
| [ 8.940000] o Transmit checksum offload supported | |
| [ 8.940000] o Driver ERROR statistics enabled | |
| [ 8.950000] o Driver INFO statistics enabled | |
| [ 8.950000] o Driver DEBUG statistics enabled | |
| [ 8.960000] o Switch support enabled | |
| [ 8.960000] | |
| [ 8.970000] o Loading network interface(s) | |
| [ 8.970000] | |
| [ 8.970000] o Port 0 is connected to Linux netdevice | |
| [ 8.980000] giga p=0: mtu=1500, mac=cf821e74 | |
| [ 9.550000] o eth0, ifindex = 2, GbE port = 0 | |
| [ 9.560000] | |
| [ 9.560000] o Port 1 is connected to Linux netdevice | |
| [ 9.560000] giga p=1: mtu=1500, mac=cf821e74 | |
| [ 9.580000] o eth1, ifindex = 3, GbE port = 1 | |
| [ 9.580000] | |
| [ 9.580000] o Port 2 is connected to Linux netdevice | |
| [ 9.590000] pon p=2: mtu=1500, mac=cf821e74 | |
| [ 9.610000] o eth2, ifindex = 4, GbE port = 2 | |
| [ 9.610000] | |
| [ 9.610000] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI | |
| [ 9.620000] Copyright (c) 1999-2006 Intel Corporation. | |
| [ 9.700000] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 | |
| [ 9.710000] e1000e: Copyright (c) 1999-2008 Intel Corporation. | |
| [ 9.730000] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI | |
| [ 9.730000] e100: Copyright(c) 1999-2006 Intel Corporation | |
| [ 9.760000] PPP generic driver version 2.4.2 | |
| [ 9.780000] NET: Registered protocol family 24 | |
| [ 9.800000] mice: PS/2 mouse device common for all mice | |
| [ 9.800000] i2c /dev entries driver | |
| [ 9.860000] Orion Watchdog Timer: Initial timeout 21 sec | |
| [ 9.860000] Orion Watchdog Timer: running at boot (6 sec left), resetting | |
| [ 9.910000] cpuidle: using governor ladder | |
| [ 10.060000] TCP cubic registered | |
| [ 10.060000] NET: Registered protocol family 10 | |
| [ 10.070000] IPv6 over IPv4 tunneling driver | |
| [ 10.090000] NET: Registered protocol family 17 | |
| [ 10.090000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> | |
| [ 10.100000] All bugs added by David S. Miller <davem@redhat.com> | |
| [ 10.220000] CPH: misc device cph registered with minor: 61 | |
| [ 10.260000] = MC MAC LEARN Module SYS FS Init ended successfully = | |
| [ 10.260000] Marvell Kirkwood2 Power Management Initializing | |
| [ 10.370000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) | |
| [ 10.380000] Freeing init memory: 10684K | |
| [ 10.390000] Warning: unable to open an initial console. | |
| [ 10.510000] ---- initramfs ('/init') | |
| [ 10.530000] mounted /proc | |
| [ 10.540000] mounted /sys | |
| [ 10.560000] mounted /dev/pts | |
| [ 10.580000] mounted /dev/shm | |
| INIT: version 2.88 booting | |
| INIT: Entering runlevel: 1 | |
| [ 10.760000] mkdir failed for /tmp/run, File exists | |
| [ 10.810000] ---- S01logging | |
| [ 10.980000] ---- S01watchdog | |
| [ 11.020000] ---- S02gfiber | |
| [ 11.130000] WATCHDOG: Device closed unexpectedly - timer will not stop | |
| [ 11.210000] <<ERROR CODE>>: -8 | |
| [ 11.270000] ---- S03coredumps | |
| [ 11.340000] ---- S03prodticker | |
| [ 11.490000] ---- S03resetmonitor | |
| [ 11.540000] ---- S03rtwatcher | |
| [ 11.550000] rtwatcher is disabled for crashiness testing | |
| [ 11.610000] ---- S04sysmgr | |
| [ 11.700000] ---- S07leds | |
| [ 11.950000] ---- S10time | |
| [ 12.210000] ---- S20ssl | |
| [ 12.590000] ---- S20urandom | |
| [ 12.600000] Initializing random number generator... done. | |
| [ 12.660000] ---- S40lan | |
| [ 12.690000] Starting LAN. | |
| [ 12.830000] pool #0: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added | |
| [ 12.830000] BM pool #0 for HWF: bufSize=2016 - 2048 of 2048 buffers added | |
| [ 12.830000] BM pool #1 for HWF: bufSize= 256 - 4096 of 4096 buffers added | |
| [ 12.840000] eth0: started | |
| [ 12.860000] ADDRCONF(NETDEV_UP): eth0: link is not ready | |
| [ 12.940000] ---- S41staticip | |
| [ 12.970000] ---- S50dropbear | |
| [ 13.000000] ---- S50telnetd | |
| [ 13.120000] ---- S70pon | |
| [ 13.130000] Adding devices. | |
| [ 13.160000] Starting XPON. | |
| [ 13.240000] ---- S71data | |
| [ 13.270000] Switching to GPON mode. | |
| [ 13.520000] Starting data configuration. | |
| [ 13.540000] /dev/mem opened. | |
| [ 13.540000] Memory mapped at address 0x40006000. | |
| [ 13.540000] Value at address 0xF10D0050 (0x40006050): 0x0 | |
| [ 13.550000] Written 0x0; readback 0x0 | |
| [ 13.560000] /dev/mem opened. | |
| [ 13.560000] Memory mapped at address 0x40006000. | |
| [ 13.570000] Value at address 0xF10C802C (0x4000602c): 0x0 | |
| [ 13.570000] Written 0x3FFFFFF; readback 0x3FFFFFF | |
| [ 13.590000] /dev/mem opened. | |
| [ 13.590000] Memory mapped at address 0x40006000. | |
| [ 13.590000] Value at address 0xF10C8030 (0x40006030): 0x0 | |
| [ 13.600000] Written 0x3FFFFFF; readback 0x3FFFFFF | |
| [ 13.610000] /dev/mem opened. | |
| [ 13.620000] Memory mapped at address 0x40006000. | |
| [ 13.620000] Value at address 0xF10C8034 (0x40006034): 0x0 | |
| [ 13.630000] Written 0x3FFFFFF; readback 0x3FFFFFF | |
| [ 13.640000] /dev/mem opened. | |
| [ 13.640000] Memory mapped at address 0x40006000. | |
| [ 13.650000] Value at address 0xF10C8038 (0x40006038): 0x0 | |
| [ 13.650000] Written 0x3FFFFFF; readback 0x3FFFFFF | |
| [ 13.660000] /dev/mem opened. | |
| [ 13.670000] Memory mapped at address 0x40006000. | |
| [ 13.670000] Value at address 0xF10C8000 (0x40006000): 0x77777 | |
| [ 13.680000] Written 0x377777; readback 0x377777 | |
| [ 13.700000] ---- S72wan | |
| [ 13.760000] Starting WAN. | |
| [ 13.920000] Starting interface. | |
| [ 13.950000] pool #2: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added | |
| [ 13.950000] BM pool #2 for HWF: bufSize=2016 - 2048 of 2048 buffers added | |
| [ 13.950000] BM pool #3 for HWF: bufSize= 256 - 4096 of 4096 buffers added | |
| [ 13.950000] pon_link_status_polling_func is uninitialized | |
| [ 13.960000] pon0: started | |
| [ 14.000000] ADDRCONF(NETDEV_UP): pon0: link is not ready | |
| [ 14.070000] Configuring data path. | |
| [ 14.090000] Starting sycl | |
| [ 14.230000] Starting DHCP on man | |
| [ 14.440000] ---- S73glaser | |
| [ 14.740000] dhclient6: Warning: Experiment 'BigInitRwnd' not registered. | |
| [ 14.890000] <<ERROR CODE>>: -8 | |
| [ 14.970000] ---- S75ntpd | |
| [ 15.120000] ---- S85catawampus | |
| [ 15.420000] WARNING: using default (module_tpmSetup:792) cfg file path: /etc/xml_params/tpm_xml_cfg_file.xml | |
| [ 15.530000] validEn = 1 | |
| [ 15.830000] pon_type = GPON | |
| [ 15.830000] ============================ | |
| [ 15.830000] Reg# VLAN etype | |
| [ 15.840000] ============================ | |
| [ 15.840000] 0 0x8100 | |
| [ 15.840000] 1 0x88a8 | |
| [ 15.850000] 2 0x9100 | |
| [ 15.850000] 3 0xaabb | |
| [ 15.850000] ============================ | |
| [ 15.860000] wifi_vir_uni_enable => en= 0 | |
| [ 15.860000] cfgPncParse = 1 | |
| [ 15.860000] cfgCpuLoopback = 0 | |
| [ 15.870000] trace_debug_info = 0xe000ffff | |
| [ 16.030000] OMCI ETY = 0xABCD | |
| [ 16.040000] IGMP snooping: enable 1 | |
| [ 16.040000] IGMP snooping: que 7 | |
| [ 16.040000] igmp_mode port(0), mode(2) | |
| [ 16.050000] igmp_mode port(1), mode(2) | |
| [ 16.050000] igmp_mode port(2), mode(2) | |
| [ 16.050000] igmp_mode port(3), mode(2) | |
| [ 16.060000] igmp_mode port(4), mode(2) | |
| [ 16.060000] igmp_mode port(5), mode(2) | |
| [ 16.070000] igmp_mode port(6), mode(2) | |
| [ 16.070000] igmp_mode port(7), mode(2) | |
| [ 16.070000] igmp_mode port(8), mode(2) | |
| [ 16.080000] igmp_mode port(9), mode(2) | |
| [ 16.080000] mc_filter_mode 3 | |
| [ 16.080000] mc_per_uni_vlan_xlat 0 | |
| [ 16.090000] mc_pppoe_enable 1 | |
| [ 16.090000] mc_hwf_queue 7 | |
| [ 16.090000] mc_cpu_queue 0 | |
| [ 16.100000] ipv4_mc_support 1 | |
| [ 16.100000] ipv6_mc_support 1 | |
| [ 16.100000] IPV4_MTU: mtu 1978 | |
| [ 16.110000] IPV4_PPPOE_MTU: mtu 1970 | |
| [ 16.110000] IPV6_MTU: mtu 0 | |
| [ 16.110000] IPV6_PPPOE_MTU: mtu 0 | |
| [ 16.120000] IPV6_MTU: mtu 0 | |
| [ 16.120000] IPV4_MTU: mtu 1978 | |
| [ 16.120000] PPPOE_ENABLE: enable 1 | |
| [ 16.130000] num_vlan_tags 2 | |
| [ 16.130000] US_XML_MTU_SETTING_ENABLE_E: enable 0 | |
| [ 16.130000] cpu_rx_queue 0 | |
| [ 16.140000] ttl_illegal_action 2 | |
| [ 16.140000] tcp_flag_check 1 | |
| [ 16.140000] SW port FC Disabled | |
| [ 16.150000] ====================================== | |
| [ 16.150000] ETH COMPLEX | |
| [ 16.160000] ====================================== | |
| [ 16.160000] eth_cmplx_profile 10 | |
| [ 16.160000] ====================================== | |
| [ 16.170000] ETH PORTS | |
| [ 16.170000] ====================================== | |
| [ 16.180000] 0) src_port 0 switch_port 0 | |
| [ 16.180000] 1) src_port 1 switch_port 1 | |
| [ 16.190000] 2) src_port 2 switch_port 2 | |
| [ 16.190000] 3) src_port 3 switch_port 3 | |
| [ 16.190000] ====================================== | |
| [ 16.200000] ====================================== | |
| [ 16.200000] GMAC PORTS | |
| [ 16.210000] ====================================== | |
| [ 16.210000] port 0 port_src 0 | |
| [ 16.220000] ====================================== | |
| [ 16.220000] ====================================== | |
| [ 16.230000] ETH COMPLEX | |
| [ 16.230000] ====================================== | |
| [ 16.240000] active_wan 2 | |
| [ 16.240000] ====================================== | |
| [ 16.240000] GMAC connection | |
| [ 16.250000] ====================================== | |
| [ 16.250000] num_tcont_llid 8 | |
| [ 16.260000] ====================================== | |
| [ 16.260000] GMAC RXQs | |
| [ 16.270000] ====================================== | |
| [ 16.270000] gmac 0 rxq 0 size 128 | |
| [ 16.280000] gmac 0 rxq 1 size 128 | |
| [ 16.280000] gmac 0 rxq 2 size 128 | |
| [ 16.280000] gmac 0 rxq 3 size 128 | |
| [ 16.290000] gmac 0 rxq 4 size 128 | |
| [ 16.290000] gmac 0 rxq 5 size 128 | |
| [ 16.290000] gmac 0 rxq 6 size 128 | |
| [ 16.300000] gmac 0 rxq 7 size 128 | |
| [ 16.300000] gmac 1 rxq 0 size 128 | |
| [ 16.300000] gmac 1 rxq 1 size 128 | |
| [ 16.310000] gmac 1 rxq 2 size 128 | |
| [ 16.310000] gmac 1 rxq 3 size 128 | |
| [ 16.310000] gmac 1 rxq 4 size 128 | |
| [ 16.320000] gmac 1 rxq 5 size 128 | |
| [ 16.320000] gmac 1 rxq 6 size 128 | |
| [ 16.320000] gmac 1 rxq 7 size 128 | |
| [ 16.330000] gmac 2 rxq 0 size 128 | |
| [ 16.330000] gmac 2 rxq 1 size 128 | |
| [ 16.330000] gmac 2 rxq 2 size 128 | |
| [ 16.340000] gmac 2 rxq 3 size 128 | |
| [ 16.340000] gmac 2 rxq 4 size 128 | |
| [ 16.340000] gmac 2 rxq 5 size 128 | |
| [ 16.350000] gmac 2 rxq 6 size 128 | |
| [ 16.350000] gmac 2 rxq 7 size 128 | |
| [ 16.350000] ====================================== | |
| [ 16.360000] ====================================== | |
| [ 16.360000] GMAC TX | |
| [ 16.370000] ====================================== | |
| [ 16.370000] TX port 0 | |
| [ 16.370000] ------------ | |
| [ 16.380000] TX queue 0: valid 1 owner 0 owner num 0 size 256 weight 0 sched 0 | |
| [ 16.380000] TX queue 1: valid 1 owner 3 owner num 0 size 256 weight 0 sched 0 | |
| [ 16.390000] TX queue 2: valid 1 owner 0 owner num 1 size 256 weight 0 sched 0 | |
| [ 16.400000] TX queue 3: valid 1 owner 3 owner num 1 size 256 weight 0 sched 0 | |
| [ 16.410000] TX queue 4: valid 1 owner 0 owner num 2 size 256 weight 0 sched 0 | |
| [ 16.410000] TX queue 5: valid 1 owner 3 owner num 2 size 256 weight 0 sched 0 | |
| [ 16.420000] TX queue 6: valid 1 owner 0 owner num 3 size 256 weight 0 sched 0 | |
| [ 16.430000] TX queue 7: valid 1 owner 3 owner num 3 size 256 weight 0 sched 0 | |
| [ 16.440000] ====================================== | |
| [ 16.440000] TX port 1 | |
| [ 16.440000] ------------ | |
| [ 16.450000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.450000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.460000] ====================================== | |
| [ 16.460000] TX port 2 | |
| [ 16.470000] ------------ | |
| [ 16.470000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.480000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.480000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.490000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.500000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.510000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.510000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.520000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.530000] ====================================== | |
| [ 16.530000] TX port 3 | |
| [ 16.540000] ------------ | |
| [ 16.540000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.550000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.550000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.560000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.570000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.570000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.580000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.590000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.600000] ====================================== | |
| [ 16.600000] TX port 4 | |
| [ 16.600000] ------------ | |
| [ 16.610000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.610000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.620000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.630000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.640000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.640000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.650000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.660000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.670000] ====================================== | |
| [ 16.670000] TX port 5 | |
| [ 16.670000] ------------ | |
| [ 16.680000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.680000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.690000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.700000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.700000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.710000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.720000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.730000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.730000] ====================================== | |
| [ 16.740000] TX port 6 | |
| [ 16.740000] ------------ | |
| [ 16.740000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.750000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.760000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.770000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.770000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.780000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.790000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.790000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.800000] ====================================== | |
| [ 16.810000] TX port 7 | |
| [ 16.810000] ------------ | |
| [ 16.810000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.820000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.830000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.830000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.840000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.850000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.860000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.860000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.870000] ====================================== | |
| [ 16.880000] TX port 8 | |
| [ 16.880000] ------------ | |
| [ 16.880000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.890000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.890000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.900000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.910000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.920000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.920000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.930000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 16.940000] ====================================== | |
| [ 16.940000] TX port 9 | |
| [ 16.950000] ------------ | |
| [ 16.950000] TX queue 0: valid 1 owner 0 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.960000] TX queue 1: valid 1 owner 1 owner num 0 size 1024 weight 0 sched 0 | |
| [ 16.960000] TX queue 2: valid 1 owner 0 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.970000] TX queue 3: valid 1 owner 1 owner num 1 size 1024 weight 0 sched 0 | |
| [ 16.980000] TX queue 4: valid 1 owner 0 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.990000] TX queue 5: valid 1 owner 1 owner num 2 size 1024 weight 0 sched 0 | |
| [ 16.990000] TX queue 6: valid 1 owner 0 owner num 3 size 1024 weight 0 sched 0 | |
| [ 17.000000] TX queue 7: valid 1 owner 1 owner num 3 size 1024 weight 0 sched 0 | |
| [ 17.010000] ====================================== | |
| [ 17.010000] ====================================== | |
| [ 17.020000] GMAC Marvell Header Enable | |
| [ 17.020000] ====================================== | |
| [ 17.030000] gmac0_mh_en 0 | |
| [ 17.030000] gmac1_mh_en 0 | |
| [ 17.030000] ====================================== | |
| [ 17.040000] GMAC BUFS | |
| [ 17.040000] ====================================== | |
| [ 17.050000] gmac 0 large_bufs 2048 small_bufs 4096 | |
| [ 17.050000] gmac 1 large_bufs 2048 small_bufs 4096 | |
| [ 17.060000] gmac 2 large_bufs 128 small_bufs 512 | |
| [ 17.060000] ====================================== | |
| [ 17.070000] ====================================== | |
| [ 17.070000] PnC range | |
| [ 17.080000] ====================================== | |
| [ 17.080000] 0: num 0 type 0 size 1 cntr_grp 0 lu_mask 1 min_res_level 1 | |
| [ 17.090000] 1: num 1 type 0 size 0 cntr_grp 3 lu_mask 1 min_res_level 0 | |
| [ 17.090000] 2: num 2 type 0 size 5 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.100000] 3: num 3 type 0 size 9 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.110000] 4: num 4 type 0 size 0 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.110000] 5: num 5 type 0 size 20 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.120000] 6: num 6 type 0 size 13 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.130000] 7: num 7 type 0 size 3 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.140000] 8: num 8 type 0 size 154 cntr_grp 1 lu_mask 1 min_res_level 0 | |
| [ 17.140000] 9: num 9 type 0 size 16 cntr_grp 2 lu_mask 1 min_res_level 0 | |
| [ 17.150000] 10: num 10 type 0 size 6 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.160000] 11: num 11 type 1 size 16 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.160000] 12: num 12 type 1 size 64 cntr_grp 3 lu_mask 0 min_res_level 0 | |
| [ 17.170000] 13: num 13 type 0 size 12 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.180000] 14: num 14 type 0 size 4 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.180000] 15: num 15 type 0 size 3 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.190000] 16: num 16 type 0 size 4 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.200000] 17: num 17 type 0 size 3 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.200000] 18: num 18 type 1 size 16 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.210000] 19: num 19 type 1 size 16 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.220000] 20: num 20 type 1 size 2 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.220000] 21: num 21 type 1 size 17 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.230000] 22: num 22 type 1 size 3 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.240000] 23: num 23 type 1 size 8 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.250000] 24: num 24 type 1 size 22 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.250000] 25: num 25 type 1 size 32 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.260000] 26: num 26 type 1 size 22 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.270000] 27: num 27 type 1 size 0 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.270000] 28: num 28 type 0 size 0 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.280000] 29: num 29 type 0 size 1 cntr_grp 0 lu_mask 1 min_res_level 0 | |
| [ 17.290000] ====================================== | |
| [ 17.290000] catch_all_pkt_action 1 | |
| [ 17.300000] dsMhConf = 0 | |
| [ 17.300000] ety_dsa_enable 0 | |
| [ 17.300000] ipv6_5t_enable 1 | |
| [ 17.300000] split_mod_enable 1 | |
| [ 17.310000] split_mod_p_bit: 0 1 2 3 4 5 6 7 | |
| [ 17.310000] split_vlan_num 16 | |
| [ 17.320000] split_mod_mode 1 | |
| [ 17.320000] ctc_cnm_enable 0 | |
| [ 17.320000] ipv6_parse_window_t 0 | |
| [ 17.320000] pnc_mac_learn_enable 0 | |
| [ 17.330000] switch_init = 0 | |
| [ 17.330000] ds_mac_based_trunking enable 0 | |
| [ 17.340000] (error) tpm_init_igmp_get(382): IGMP pkt_frwd_mod port: 5 - missing initialization. | |
| [ 17.340000] (error) tpm_init_igmp_get(382): IGMP pkt_frwd_mod port: 6 - missing initialization. | |
| [ 17.350000] (error) tpm_init_igmp_get(382): IGMP pkt_frwd_mod port: 7 - missing initialization. | |
| [ 17.360000] (error) tpm_init_igmp_get(382): IGMP pkt_frwd_mod port: 8 - missing initialization. | |
| [ 17.360000] (warn) tpm_init_info_validate(2121): | |
| [ 17.370000] CTC CM: Since CTC CnM is disabled, CNM_IPV4_PRE range size should be Zero! | |
| [ 17.380000] (warn) tpm_init_info_validate(2125): | |
| [ 17.380000] CTC CM: Since CTC CnM is disabled, CNM_MAIN range size should be Zero! | |
| [ 17.390000] TPM_SRC_PORT: 0, value: 2 | |
| [ 17.390000] TPM_SRC_PORT: 1, value: 2 | |
| [ 17.400000] TPM_SRC_PORT: 2, value: 2 | |
| [ 17.400000] TPM_SRC_PORT: 3, value: 2 | |
| [ 17.400000] TPM_SRC_PORT: 4, value: 2 | |
| [ 17.410000] TPM_SRC_PORT: 5, value: 2 | |
| [ 17.410000] TPM_SRC_PORT: 6, value: 2 | |
| [ 17.410000] TPM_SRC_PORT: 7, value: 2 | |
| [ 17.420000] TPM_SRC_PORT: 8, value: 2 | |
| [ 17.420000] TPM_SRC_PORT: 9, value: 2 | |
| [ 17.430000] (warn) tpm_init_api_rng_init(2481): PNC Range(1) was not created - rc(6) | |
| [ 17.430000] (warn) tpm_init_api_rng_init(2481): PNC Range(28) was not created - rc(6) | |
| [ 17.440000] (warn) tpm_init_api_rng_init(2481): PNC Range(4) was not created - rc(6) | |
| [ 17.450000] (warn) tpm_init_txq_size_set(2973): port0 already started, tx_queue sizes will not be updated | |
| [ 17.460000] (warn) tpm_init_txq_size_set(2973): port2 already started, tx_queue sizes will not be updated | |
| [ 17.470000] (warn) tpm_init_rxq_size_set(3015): port0 already started, rx_queue sizes will not be updated | |
| [ 17.480000] (warn) tpm_init_rxq_size_set(3015): port2 already started, rx_queue sizes will not be updated | |
| [ 17.490000] GMAC(0) mh_en(0) amber_port_num(-1) | |
| [ 17.500000] GMAC(2) mh_en(1) amber_port_num(-1) | |
| [ 17.500000] (warn) tpm_init_bm_pool(3655): port0 already started, port bm_pools will not be updated | |
| [ 17.510000] (warn) tpm_init_bm_pool(3655): port2 already started, port bm_pools will not be updated | |
| [ 17.520000] ===== chain_area: base entry 0x20e ===== | |
| [ 17.530000] [GMAC0]: | |
| [ 17.530000] chain-1, 0x20e - 0x22d, chain_num: 32 | |
| [ 17.540000] chain-2, 0x22e - 0x2ed, chain_num: 64 | |
| [ 17.540000] chain-3, 0x2ee - 0x545, chain_num: 300 | |
| [ 17.550000] chain-4, 0x546 - 0x555, chain_num: 8 | |
| [ 17.550000] chain-5, 0x556 - 0x573, chain_num: 6 | |
| [ 17.560000] chain-6, 0x574 - 0x81b, chain_num: 170 | |
| [ 17.560000] chain-7, 0x81c - 0xd3f, chain_num: 94 | |
| [ 17.570000] chain-8, 0xd40 - 0xdbf, chain_num: 16 | |
| [ 17.570000] chain-9, 0xdc0 - 0xf7f, chain_num: 64 | |
| [ 17.580000] chain-10, 0xf80 - 0xfff, chain_num: 16 | |
| [ 17.580000] ===== chain_area: base entry 0x20e ===== | |
| [ 17.590000] [GMAC1]: | |
| [ 17.590000] chain-1, 0x20e - 0x22d, chain_num: 32 | |
| [ 17.600000] chain-2, 0x22e - 0x2ed, chain_num: 64 | |
| [ 17.600000] chain-3, 0x2ee - 0x545, chain_num: 300 | |
| [ 17.610000] chain-4, 0x546 - 0x555, chain_num: 8 | |
| [ 17.610000] chain-5, 0x556 - 0x573, chain_num: 6 | |
| [ 17.620000] chain-6, 0x574 - 0x81b, chain_num: 170 | |
| [ 17.620000] chain-7, 0x81c - 0xd3f, chain_num: 94 | |
| [ 17.630000] chain-8, 0xd40 - 0xdbf, chain_num: 16 | |
| [ 17.630000] chain-9, 0xdc0 - 0xf7f, chain_num: 64 | |
| [ 17.640000] chain-10, 0xf80 - 0xfff, chain_num: 16 | |
| [ 17.650000] ===== chain_area: base entry 0x20e ===== | |
| [ 17.650000] [GMAC2]: | |
| [ 17.650000] chain-1, 0x20e - 0x22d, chain_num: 32 | |
| [ 17.660000] chain-2, 0x22e - 0x2ed, chain_num: 64 | |
| [ 17.660000] chain-3, 0x2ee - 0x545, chain_num: 300 | |
| [ 17.670000] chain-4, 0x546 - 0x555, chain_num: 8 | |
| [ 17.680000] chain-5, 0x556 - 0x573, chain_num: 6 | |
| [ 17.680000] chain-6, 0x574 - 0x81b, chain_num: 170 | |
| [ 17.690000] chain-7, 0x81c - 0xd3f, chain_num: 94 | |
| [ 17.690000] chain-8, 0xd40 - 0xdbf, chain_num: 16 | |
| [ 17.700000] chain-9, 0xdc0 - 0xf7f, chain_num: 64 | |
| [ 17.700000] chain-10, 0xf80 - 0xfff, chain_num: 16 | |
| [ 17.710000] (warn) tpm_init_system_mib_reset(4022): TPM_PNC_IPV6_L4_MC_DS SIZE should be 1, too big now, it is a waste | |
| [ 17.720000] (warn) tpm_proc_mtu_init(1116): PNC range(17) too big, current size(3). it is a waste with MTU disabled, size should be 2 | |
| [ 17.730000] (warn) tpm_proc_mtu_init(1132): mtu check is not enabled! | |
| [ 17.730000] | |
| [ 17.730000] = TPM Module Init ended successfully = | |
| [ 18.110000] ---- S94psstat | |
| [ 18.290000] ---- S94startupmods | |
| [ 18.510000] ---- S95uploadlog | |
| [ 18.850000] ---- S99diags | |
| [ 19.170000] diag is not set: skipping. | |
| [ 19.260000] ---- S99isoping | |
| [ 19.400000] ---- S99onustats | |
| [ 19.690000] ---- S99readallfiles | |
| [ 19.890000] ---- S99xprintk | |
| Not running getty on 'ttyS0'. To activate, boot with debug=1 or login=1. |