Created
August 21, 2019 07:49
-
-
Save christianlupus/5f0bd324c78d4f69c16d487873569fbc to your computer and use it in GitHub Desktop.
Smart output of hdd
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-5.2.2-arch1-1-ARCH] (local build) | |
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org | |
=== START OF INFORMATION SECTION === | |
Model Family: Hitachi Ultrastar A7K2000 | |
Device Model: Hitachi HUA722020ALA331 | |
Serial Number: YBKVP82F | |
LU WWN Device Id: 5 000cca 221f667f8 | |
Firmware Version: JKAOA3NH | |
User Capacity: 2.000.398.934.016 bytes [2,00 TB] | |
Sector Size: 512 bytes logical/physical | |
Rotation Rate: 7200 rpm | |
Form Factor: 3.5 inches | |
Device is: In smartctl database [for details use: -P show] | |
ATA Version is: ATA8-ACS T13/1699-D revision 4 | |
SATA Version is: SATA 2.6, 3.0 Gb/s | |
Local Time is: Wed Aug 21 09:48:07 2019 CEST | |
SMART support is: Available - device has SMART capability. | |
SMART support is: Enabled | |
=== START OF READ SMART DATA SECTION === | |
SMART overall-health self-assessment test result: PASSED | |
General SMART Values: | |
Offline data collection status: (0x84) Offline data collection activity | |
was suspended by an interrupting command from host. | |
Auto Offline Data Collection: Enabled. | |
Self-test execution status: ( 0) The previous self-test routine completed | |
without error or no self-test has ever | |
been run. | |
Total time to complete Offline | |
data collection: (23065) seconds. | |
Offline data collection | |
capabilities: (0x5b) SMART execute Offline immediate. | |
Auto Offline data collection on/off support. | |
Suspend Offline collection upon new | |
command. | |
Offline surface scan supported. | |
Self-test supported. | |
No Conveyance Self-test supported. | |
Selective Self-test supported. | |
SMART capabilities: (0x0003) Saves SMART data before entering | |
power-saving mode. | |
Supports SMART auto save timer. | |
Error logging capability: (0x01) Error logging supported. | |
General Purpose Logging supported. | |
Short self-test routine | |
recommended polling time: ( 1) minutes. | |
Extended self-test routine | |
recommended polling time: ( 384) minutes. | |
SCT capabilities: (0x003d) SCT Status supported. | |
SCT Error Recovery Control supported. | |
SCT Feature Control supported. | |
SCT Data Table supported. | |
SMART Attributes Data Structure revision number: 16 | |
Vendor Specific SMART Attributes with Thresholds: | |
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
1 Raw_Read_Error_Rate 0x000b 086 086 016 Pre-fail Always - 8257536 | |
2 Throughput_Performance 0x0005 131 131 054 Pre-fail Offline - 107 | |
3 Spin_Up_Time 0x0007 148 148 024 Pre-fail Always - 431 (Average 545) | |
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 14 | |
5 Reallocated_Sector_Ct 0x0033 086 086 005 Pre-fail Always - 420 | |
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 | |
8 Seek_Time_Performance 0x0005 119 119 020 Pre-fail Offline - 36 | |
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1006 | |
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 | |
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 14 | |
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 173 | |
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 173 | |
194 Temperature_Celsius 0x0002 162 162 000 Old_age Always - 37 (Min/Max 20/57) | |
196 Reallocated_Event_Count 0x0032 086 086 000 Old_age Always - 428 | |
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 10 | |
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 | |
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 1 | |
SMART Error Log Version: 1 | |
ATA Error Count: 107 (device log contains only the most recent five errors) | |
CR = Command Register [HEX] | |
FR = Features Register [HEX] | |
SC = Sector Count Register [HEX] | |
SN = Sector Number Register [HEX] | |
CL = Cylinder Low Register [HEX] | |
CH = Cylinder High Register [HEX] | |
DH = Device/Head Register [HEX] | |
DC = Device Command Register [HEX] | |
ER = Error register [HEX] | |
ST = Status register [HEX] | |
Powered_Up_Time is measured from power on, and printed as | |
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, | |
SS=sec, and sss=millisec. It "wraps" after 49.710 days. | |
Error 107 occurred at disk power-on lifetime: 1001 hours (41 days + 17 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
40 51 0b 25 fb be 00 Error: WP at LBA = 0x00befb25 = 12516133 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
61 08 48 70 f9 fd 40 08 6d+05:26:11.433 WRITE FPDMA QUEUED | |
61 08 40 50 f9 fd 40 08 6d+05:26:11.432 WRITE FPDMA QUEUED | |
61 08 38 18 f9 fd 40 08 6d+05:26:11.432 WRITE FPDMA QUEUED | |
61 20 30 b8 37 e7 40 08 6d+05:26:11.432 WRITE FPDMA QUEUED | |
61 08 28 a8 37 e7 40 08 6d+05:26:11.432 WRITE FPDMA QUEUED | |
Error 106 occurred at disk power-on lifetime: 1001 hours (41 days + 17 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
40 51 08 20 fb be 00 Error: UNC at LBA = 0x00befb20 = 12516128 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
60 08 c0 20 fb be 40 08 6d+05:25:45.177 READ FPDMA QUEUED | |
ea 00 00 00 00 00 a0 08 6d+05:25:45.175 FLUSH CACHE EXT | |
ea 00 00 00 00 00 a0 08 6d+05:25:45.056 FLUSH CACHE EXT | |
61 08 68 10 08 00 40 08 6d+05:25:45.054 WRITE FPDMA QUEUED | |
ea 00 00 00 00 00 a0 08 6d+05:25:45.053 FLUSH CACHE EXT | |
Error 105 occurred at disk power-on lifetime: 1001 hours (41 days + 17 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
40 51 08 20 fb be 00 Error: WP at LBA = 0x00befb20 = 12516128 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
61 10 f0 a0 60 f0 40 08 6d+05:25:27.440 WRITE FPDMA QUEUED | |
61 10 80 40 f2 d8 40 08 6d+05:25:27.390 WRITE FPDMA QUEUED | |
60 08 78 60 dd ee 40 08 6d+05:25:27.327 READ FPDMA QUEUED | |
60 08 70 20 fb be 40 08 6d+05:25:27.322 READ FPDMA QUEUED | |
61 00 e8 00 50 08 40 08 6d+05:25:27.305 WRITE FPDMA QUEUED | |
Error 104 occurred at disk power-on lifetime: 1001 hours (41 days + 17 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
40 51 08 58 f8 be 00 Error: UNC at LBA = 0x00bef858 = 12515416 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
60 08 18 58 f8 be 40 08 6d+05:14:58.990 READ FPDMA QUEUED | |
60 08 00 50 be ee 40 08 6d+05:14:58.711 READ FPDMA QUEUED | |
ea 00 00 00 00 00 a0 08 6d+05:14:58.603 FLUSH CACHE EXT | |
61 00 d0 00 25 e1 40 08 6d+05:14:58.598 WRITE FPDMA QUEUED | |
61 00 a0 00 e5 b0 40 08 6d+05:14:58.506 WRITE FPDMA QUEUED | |
Error 103 occurred at disk power-on lifetime: 1001 hours (41 days + 17 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
40 51 05 eb f8 be 00 Error: UNC at LBA = 0x00bef8eb = 12515563 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
60 08 f8 b0 f8 be 40 08 6d+05:13:54.756 READ FPDMA QUEUED | |
61 20 b8 00 6f 98 40 08 6d+05:13:54.749 WRITE FPDMA QUEUED | |
60 08 a8 e8 f8 be 40 08 6d+05:13:54.738 READ FPDMA QUEUED | |
60 28 a0 f0 58 c3 40 08 6d+05:13:54.696 READ FPDMA QUEUED | |
61 10 40 30 05 20 40 08 6d+05:13:54.690 WRITE FPDMA QUEUED | |
SMART Self-test log structure revision number 1 | |
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
# 1 Short offline Completed without error 00% 971 - | |
# 2 Short offline Completed without error 00% 947 - | |
# 3 Short offline Completed without error 00% 923 - | |
# 4 Short offline Completed without error 00% 899 - | |
# 5 Short offline Completed without error 00% 875 - | |
# 6 Short offline Completed without error 00% 851 - | |
# 7 Extended offline Completed: read failure 30% 834 2897739927 | |
# 8 Short offline Completed without error 00% 803 - | |
# 9 Short offline Completed without error 00% 779 - | |
#10 Short offline Completed without error 00% 755 - | |
#11 Short offline Completed without error 00% 731 - | |
#12 Short offline Completed without error 00% 707 - | |
#13 Extended offline Completed: read failure 30% 691 2939574803 | |
#14 Short offline Completed without error 00% 635 - | |
#15 Short offline Completed without error 00% 611 - | |
#16 Short offline Completed without error 00% 587 - | |
#17 Short offline Completed without error 00% 563 - | |
#18 Short offline Completed without error 00% 539 - | |
#19 Short offline Completed without error 00% 515 - | |
#20 Extended offline Completed without error 00% 505 - | |
#21 Short offline Completed without error 00% 467 - | |
SMART Selective self-test log data structure revision number 1 | |
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
1 0 0 Not_testing | |
2 0 0 Not_testing | |
3 0 0 Not_testing | |
4 0 0 Not_testing | |
5 0 0 Not_testing | |
Selective self-test flags (0x0): | |
After scanning selected spans, do NOT read-scan remainder of disk. | |
If Selective self-test is pending on power-up, resume after 0 minute delay. | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment