gistfile1.txt

Copyright 2016-2017 rpi-open-firmware authors
BUILDATE  : Jan  1 1970 00:00:01
__cxx_init: calling 5 static constructors (0x14000 - 0x14014) ...
BCM2708UsbPhy::registerDriver(): driver registered on platform IO plane
BCM2708ArmControl::registerDriver(): driver registered on platform IO plane
BCM2708PLLB::init(): PLLB VCO registered
BCM2708PLLB::registerDriver(): driver registered on platform IO plane
BCM2708Gpio::registerDriver(): driver registered on platform IO plane
[SDRAM:sdram_init]: (0) SD_CS = 0x794200
[SDRAM:switch_to_cprman_clock]: switching sdram to cprman clock (src=1, div=1), waiting for busy (4011) ...
[SDRAM:switch_to_cprman_clock]: busy set, switch complete!
[SDRAM:reset_phy]: reset_phy: resetting SDRAM PHY ...
[SDRAM:reset_phy]: reset_phy: resetting DPHY CTRL ...
[SDRAM:reset_phy_dll]: resetting aphy and dphy dlls ...
[SDRAM:reset_phy_dll]: waiting for dphy master dll to lock ...
[SDRAM:reset_phy_dll]: dphy master dll locked!
[SDRAM:sdram_init]: waiting for SDUP (210E42) ...
[SDRAM:sdram_init]: SDRAM controller has arrived! (218E42)
[SDRAM:calibrate_pvt_early]: DPHY_CSR_DQ_PAD_DRV_SLEW_CTRL = 0x223
[SDRAM:calibrate_pvt_early]: waiting for address PVT calibration ...
[SDRAM:calibrate_pvt_early]: waiting for data PVT calibration ...
[SDRAM:calibrate_pvt_early]: waiting for SDRAM calibration command ...
[SDRAM:sdram_init]: SDRAM Type: Elpida 1GB LPDDR2 (BC=0x58)
[SDRAM:reset_with_timing]: waiting for SDRAM controller to go down (218E4A) ...
[SDRAM:reset_with_timing]: SDRAM controller down!
[SDRAM:reset_with_timing]: SDRAM clock disabled!
[SDRAM:reset_with_timing]: waiting for master ddr pll to lock ...
[SDRAM:reset_with_timing]: master ddr pll locked!
[SDRAM:reset_with_timing]: SDRAM Addressing Mode: Bank=3 Row=3 Col=3 SB=0xFF
[SDRAM:reset_phy_dll]: resetting aphy and dphy dlls ...
[SDRAM:reset_phy_dll]: waiting for dphy master dll to lock ...
[SDRAM:reset_phy_dll]: dphy master dll locked!
[SDRAM:reset_with_timing]: waiting for address dll to lock ...
[SDRAM:reset_with_timing]: address dll locked!
[SDRAM:selftest]: Starting self test ...
[SDRAM:selftest_at]: Testing region at 0xC0000000 ...
[SDRAM:selftest_at]: Testing region at 0xCFF00000 ...
[SDRAM:selftest_at]: Testing region at 0xDFF00000 ...
[SDRAM:selftest_at]: Testing region at 0xEFF00000 ...
[SDRAM:selftest_at]: Testing region at 0xFFF00000 ...
[SDRAM:selftest]: Self test successful!
SDRAM initialization completed successfully!
BCM2708PowerDomainUSB::stop(): stopping ...
BCM2708PowerDomainUSB::stop(): stopped
BCM2708PowerDomainImage::powerOn(): powering on, current PM_IMAGE state: 0x1000
BCM2708PowerDomainImage::beginPowerUpSequence(): starting power up sequence ...
BCM2708PowerDomainImage::waitForPOWOK(): waiting for POWOK ...
BCM2708PowerDomainImage::waitForPOWOK(): got POWOK with CFG=0x10000
BCM2708PowerDomainImage::powerOn(): stopping power up sequence ...
BCM2708PowerDomainImage::beginPowerUpSequence(): starting power up sequence ...
BCM2708PowerDomainImage::waitForPOWOK(): waiting for POWOK ...
BCM2708PowerDomainImage::waitForPOWOK(): got POWOK with CFG=0x30000
BCM2708PowerDomainImage::completePowerUpSequence(): waiting for MRDONE ...
BCM2708PowerDomainImage::resetPeripheralsUngated(): calling v16mov gated ...
BCM2708PowerDomainImage::resetPeripheralsUngated(): ungating and resetting ...
BCM2708PowerDomainImage::resetPeripheralsUngated(): done
BCM2708PowerDomainImage::start(): CM_PERIICTL = 0x40
BCM2708PowerDomainImage::start(): CM_PERIIDIV = 0x0
BCM2708PowerDomainImage::start(): PM_IMAGE    = 0x3107F
BCM2708PowerDomainImage::start(): started
BCM2708PowerDomainUSB::start(): starting ...
BCM2708PowerDomainUSB::start(): started
BCM2708UsbPhy::start(): starting ...
BCM2708UsbPhy::start(): LAN reset
BCM2708UsbPhy::start(): started
BCM2708ArmControl::start(): starting ...
BCM2708ArmControl::loadInitialCode(): copied 57412 bytes to 0xC0000000!
BCM2708ArmControl::start(): original memstart: 0xEA000039
BCM2708ArmControl::start(): mapped VC 0xC0000000 to ARM 0x0
BCM2708ArmControl::start(): mapped peripherals VC 0x7E000000 to ARM 0x3F000000
BCM2708ArmControl::start(): ARM ID: 0x364D5241 C0: 0x0
BCM2708ArmControl::start(): using C0: 0xA04B
BCM2708ArmControl::setupClock(): initializing PLLB ...
BCM2708PLLB::setDigValues(): setting DIG values for this VCO ...
BCM2708ArmControl::setupClock(): KAIP  = 0x228
BCM2708ArmControl::setupClock(): MULTI = 0x613277
BCM2708ArmControl::setupClock(): ARM clock succesfully initialized!
BCM2708PowerDomainARM::start(): starting ...
BCM2708PowerDomainARM::powerOn(): powering on (rstnMask=0xFFFFFFBF) ...
BCM2708PowerDomainARM::beginPowerUpSequence(): starting power up sequence ...
BCM2708PowerDomainARM::waitForPOWOK(): waiting for POWOK ...
BCM2708PowerDomainARM::waitForPOWOK(): got POWOK with CFG=0x0
BCM2708PowerDomainARM::completePowerUpSequence(): waiting for MRDONE ...
BCM2708PowerDomainARM::powerOn(): domain powered on succesfully
BCM2708PowerDomainARM::start(): started
BCM2708ArmControl::bridgeStart(): setting up async bridge ...
BCM2708PowerDomainARM::setReset(): setting RSTN bits to 0x40 ...
BCM2708ArmControl::bridgeCycleBresp(): cycling through bresp bits ...
BCM2708PowerDomainARM::setReset(): setting RSTN bits to 0x40 ...
BCM2708ArmControl::bridgeStart(): starting async bridge now!
BCM2708ArmControl::bridgeStart(): bridge init done, PM_PROC is now: 0x107F!
Starting IPC monitor ...
continuing boot from here ...
[BRINGUP:main]: Firmware data: SDRAM_SIZE=0, VPU_CPUID=0x4000140
[BRINGUP:main]: Security extensions are supported!
[BRINGUP:main]: Execution mode: Supervisor
[BRINGUP:heap_init]: Initializing heap at 0x24000 with size 0x100000
__cxx_init: calling 4 static constructors (0xE000 - 0xE010) ...
[EMMC:restart_controller]: hcfg 0xE, cdiv 0x0, edm 0x8C01, hsts 0x0
[EMMC:restart_controller]: Restarting the eMMC controller ...
[EMMC:configure_pinmux]: waiting for pinmux pull update ...
[EMMC:configure_pinmux]: waiting for pinmux clock update ...
[EMMC:configure_pinmux]: ok ...
[EMMC:configure_pinmux]: pinmux configured for aux0
[EMMC:reset]: resetting controller ...
[EMMC:query_voltage_and_type]: waiting for SD (0x40ff8000) ...
[EMMC:query_voltage_and_type]: waiting for SD (0x40ff8000) ...
[EMMC:query_voltage_and_type]: waiting for SD (0x40ff8000) ...
[EMMC:query_voltage_and_type]: waiting for SD (0x40ff8000) ...
[EMMC:query_voltage_and_type]: SD card has arrived!
[EMMC:query_voltage_and_type]: This is an SDHC card!
[EMMC:identify_card]: identifying card ...
[EMMC:identify_card]: RCA = 0xaaaa
[EMMC:init_card]: Detected SD card:
    Product : SC16G 
    CSD     : Ver 2.0
    Capacity: 31116288
    Size    : 30386 
    BlockLen: 0x200 
[EMMC:init_card]: Card initialization complete: SC16G 2905MB SDHC Card
[EMMC:init_card]: Identification complete, changing clock to 50MHz for data mode ...
[EMMC:BCM2708SDHost]: eMMC driver sucessfully started!
[MBRDISK:read_mbr]: Reading master boot record ...
[MBRDISK:read_mbr]: MBR contents:
    0: FAT32-INT13 at:8192 size:524288
    1: Linux (ext2/ext3) at:532480 size:30583808
    2: <Unknown> at:0 size:0
    3: <Unknown> at:0 size:0
[MBRDISK:MbrImpl]: Disk ready!
[LDR:LoaderImpl]: Mounting boot partitiion ...
[LDR:LoaderImpl]: Boot partition mounted!
panic(): "attempted to read cmdline.txt, but it does not exist"@loader.cc:49