List of parts to print for Voron 2.4 organized by the Assembly Manuals order of assembly, allowing for just-in-time printing of parts while building the printer. Configuration is standard Voron 2.4 (Afterburner Direct Feed, DIN rail mounts) with choices for E3D, Dragon or Mosquito hot ends on a 250mm, 300mm or 350mm frame. No parts for the drag chain are included, as often these are purchased parts rather than printed.
Names of the sections (such as Gantry/X_Axis/XY Joints) match the name of the STL directory that contains the prints. Note that Voron Design uses filenames starting with [a]_ at the start of a filename to indicate parts that can be printed in an accent color.
Credit to krobertson for making a Gist of all parts. This Gist is a modified version of that list, organized by order of assembly, removed parts that don't need printing, identified parts that are optional or specific to a build, and fixed a few incorrect part listings.
[ ] [ ] rail_installation_guide_center_x2.stl
[ ] [ ] [a]_belt_tensioner_a_x2.stl
[ ] [ ] [a]_belt_tensioner_b_x2.stl
[ ] [ ] [a]_z_drive_baseplate_a_x2.stl
[ ] [ ] [a]_z_drive_baseplate_b_x2.stl
[ ] [ ] z_drive_main_a_x2.stl
[ ] [ ] z_drive_main_b_x2.stl
[ ] [ ] z_drive_retainer_a_x2.stl
[ ] [ ] z_drive_retainer_b_x2.stl
[ ] [ ] z_motor_mount_a_x2.stl
[ ] [ ] z_motor_mount_b_x2.stl
There are two different GT20 20T pully files; only one set of them should be printed
[ ] [ ] [ ] [ ] [a]_z_tensioner_x4_6mm.stl <- select one vvv (6mm pully)
[ ] [ ] [ ] [ ] [a]_z_tensioner_x4_9mm.stl <- select one ^^^ (9mm pully)
[ ] [ ] z_tensioner_bracket_a_x2.stl
[ ] [ ] z_tensioner_bracket_b_x2.stl
[ ] nozzle_probe.stl
[ ] [a]_tensioner_left.stl
[ ] [a]_tensioner_right.stl
[ ] front_idler_left_lower.stl
[ ] front_idler_left_upper.stl
[ ] front_idler_right_lower.stl
[ ] front_idler_right_upper.stl
[ ] [a]_cable_cover.stl
[ ] [ ] [a]_z_chain_retainer_bracket_x2.stl
[ ] a_drive_frame_lower.stl
[ ] a_drive_frame_upper.stl
[ ] b_drive_frame_lower.stl
[ ] b_drive_frame_upper.stl
Select one endstop_pod* , and one xy_joint_cable_bridge_* depending on your hardware kit_
[ ] [a]_endstop_pod_hall_effect.stl <- select one vvv (hall effect XY endstops)
[ ] [a]_endstop_pod_microswitch.stl <- select one ^^^ (microswitch XY endstops)
[ ] [a]_xy_joint_cable_bridge_generic.stl <= select one vvv (generic drag chain)
[ ] [a]_xy_joint_cable_bridge_igus.stl <= select one ^^^ (igus drag chain)
[ ] xy_joint_left_lower.stl
[ ] xy_joint_left_upper.stl
[ ] xy_joint_right_lower.stl
[ ] xy_joint_right_upper.stl
[ ] [ ] [ ] [ ] [a]_z_belt_clip_lower_x4.stl
[ ] [ ] [ ] [ ] [a]_z_belt_clip_upper_x4.stl
[ ] z_chain_bottom_anchor.stl
[ ] z_chain_guide.stl <-- Not in CAD or documentation
[ ] [ ] [a]_belt_clamp_x2.stl
[ ] [a]_blower_housing_front.stl
[ ] blower_housing_rear.stl
[ ] hotend_fan_mount.stl
[ ] probe_retainer_bracket.stl
[ ] x_carriage_frame_left.stl
[ ] x_carriage_frame_right.stl
[ ] x_carriage_pivot_block.stl
Select only one printhead; this is for E3D
[ ] printhead_front_e3dv6.stl
[ ] printhead_rear_e3dv6.stl
Select only one printhead; this is for Slice Mosquito
[ ] printhead_front_mosquito.stl
[ ] printhead_rear_mosquito.stl
Select only one printhead; this is for Phaetus Dragon
[ ] printhead_front_dragon.stl
[ ] printhead_rear_dragon.stl
Select the chain anchor (generic or igus) that matches your drag chain choice
[ ] [a]_connector_cover.stl
[ ] [a]_guidler.stl
[ ] [a]_latch.stl
[ ] chain_anchor_generic.stl <-- select one vvv (generic drag chain)
[ ] chain_anchor_igus.stl <-- select one ^^^ (igus drag chain)
[ ] extruder_body.stl
[ ] extruder_motor_plate.stl
[ ] latch_shuttle.stl
[ ] [ ] [ ] [ ] z_joint_lower_x4.stl
[ ] z_joint_upper_hall_effect.stl <-- if using hall effect XY
[ ] [ ] [ ] [ ] z_joint_upper_x4.stl <-- use x3 if using hall effect XY
[ ] [a]_mini12864_case_hinge.stl
[ ] mini12864_case_front.stl
[ ] mini12864_case_rear.stl
[ ] mini12864_spacer.stl
[ ] plug_panel_filtered_mains.stl
[ ] [ ] [a]_60mm_fan_blank_insert_x2.stl
[ ] [ ] [a]_belt_guard_a_x2.stl
[ ] [ ] [a]_belt_guard_b_x2.stl
[ ] [ ] side_fan_support_x2.stl
Use these skirts when printing a 250mm frame
[ ] [ ] front_rear_skirt_a_250_x2.stl
[ ] [ ] front_rear_skirt_b_250_x2.stl
[ ] [ ] side_skirt_a_250_x2.stl
[ ] [ ] side_skirt_b_250_x2.stl
Use these skirts when printing a 300mm frame
[ ] [ ] front_rear_skirt_a_300_x2.stl
[ ] [ ] front_rear_skirt_b_300_x2.stl
[ ] [ ] side_skirt_a_300_x2.stl
[ ] [ ] side_skirt_b_300_x2.stl
Use these skirts when printing a 350mm frame
[ ] [ ] front_rear_skirt_a_350_x2.stl
[ ] [ ] front_rear_skirt_b_350_x2.stl
[ ] [ ] side_skirt_a_350_x2.stl
[ ] [ ] side_skirt_b_350_x2.stl
[ ] [ ] [ ] [ ] door_hinge_x4.stl
[ ] [ ] handle_a_x2.stl
[ ] [ ] handle_b_x2.stl
[ ] [ ] latch_x2.stl
[ ] [ ] [ ] [ ] bottom_panel_clip_x4.stl
[ ] [ ] bottom_panel_hinge_x2.stl
[ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] corner_panel_clip_3mm_x12.stl <-- 3mm no foam, 6mm w/foam
[ ] [ ] [ ] [ ] corner_panel_clip_6mm_x4.stl <-- print either the 3mm or
[ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] midspan_panel_clip_3mm_x12.stl <-- the 6mm set
[ ] [ ] [ ] midspan_panel_clip_6mm_x3.stl <--
[ ] [ ] z_belt_cover_a_x2.stl
[ ] [ ] z_belt_cover_b_x2.stl
[ ] bowen_retainer.stl
[ ] spool_holder.stl
[ ] [a]_filter_access_cover.stl
[ ] [ ] [a]_exhaust_filter_mount_x2.stl
[ ] exhaust_filter_grill.stl
[ ] exhaust_filter_housing.stl
There are a number of different brackets here depending on your electronics selection.
[ ] [ ] duet_duex_bracket_x2.stl
[ ] lrs_psu_bracket_clip.stl
[ ] [ ] [ ] pcb_din_clip_x3.stl
[ ] [ ] ramps_bracket_x2.stl
[ ] raspberrypi_bracket.stl
[ ] rs25_psu_bracket_clip.stl
[ ] [ ] skr_1.3_bracket_x2.stl
[ ] [ ] skr_mini_e2_bracket_x2.stl
[ ] [ ] skr_mini_e3_bracket_x2.stl
V2.4r2 has renamed some things like
rail_installation_guide_center_x2.stltoMGN9_rail_guide_x2.stl, see this diffrail_installation_guide_center_x2.stl → STLs/Tools/MGN9_rail_guide_x2.stl
And I think page numbers are now off due to many improvements in the manual.