-
-
Save cmoulliard/17eba8ed42b81afb064d to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| https://gist.github.com/anonymous/0d1759adad6c58602ddf |
# Basic configuration
interface=wlp0s20u2
driver=nl80211
### IEEE 802.11
ssid=fuselab
hw_mode=a
# channel=11
channel=48
# channel=64
# channel=0
# WPA and WPA2 configuration
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=3
wpa_passphrase=fuselab987
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP
### DFS
ieee80211h=1
ieee80211d=1
country_code=BE
# WMM
wme_enabled=1
### IEEE 802.11n
ieee80211n=1
ht_capab=[HT20][HT40]
### IEEE 802.11ac
ieee80211ac=1
vht_oper_chwidth=1
iw list
dabou@localhost Temp$ iw list
Wiphy phy6
max # scan SSIDs: 9
max scan IEs length: 2304 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* monitor
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS)
* 2472 MHz [13] (20.0 dBm) (passive scanning, no IBSS)
* 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS)
Band 2:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5170 MHz [34] (disabled)
* 5180 MHz [36] (20.0 dBm) (passive scanning, no IBSS)
* 5190 MHz [38] (20.0 dBm) (passive scanning, no IBSS)
* 5200 MHz [40] (20.0 dBm) (passive scanning, no IBSS)
* 5210 MHz [42] (20.0 dBm) (passive scanning, no IBSS)
* 5220 MHz [44] (20.0 dBm) (passive scanning, no IBSS)
* 5230 MHz [46] (20.0 dBm) (passive scanning, no IBSS)
* 5240 MHz [48] (20.0 dBm)
* 5260 MHz [52] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5280 MHz [56] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5300 MHz [60] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5320 MHz [64] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5500 MHz [100] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5520 MHz [104] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5540 MHz [108] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5560 MHz [112] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5580 MHz [116] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5600 MHz [120] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5620 MHz [124] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5640 MHz [128] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5660 MHz [132] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5680 MHz [136] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5700 MHz [140] (20.0 dBm) (passive scanning, no IBSS, radar detection)
DFS state: usable (for 1907 sec)
* 5745 MHz [149] (disabled)
* 5765 MHz [153] (disabled)
* 5785 MHz [157] (disabled)
* 5805 MHz [161] (disabled)
* 5825 MHz [165] (disabled)
* 5920 MHz [184] (disabled)
* 5940 MHz [188] (disabled)
* 5960 MHz [192] (disabled)
* 5980 MHz [196] (disabled)
* 6000 MHz [200] (disabled)
* 6020 MHz [204] (disabled)
* 6040 MHz [208] (disabled)
* 6060 MHz [212] (disabled)
* 6080 MHz [216] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* join_ibss
* set_pmksa
* del_pmksa
* flush_pmksa
* remain_on_channel
* frame
* set_channel
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
software interface modes (can always be added):
* monitor
interface combinations are not supported
Device supports scan flush.
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
rfkill: initial event: idx=1 type=2 op=0 soft=0 hard=0
rfkill: initial event: idx=2 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=7 type=2 op=0 soft=0 hard=0
rfkill: initial event: idx=9 type=1 op=0 soft=0 hard=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Using driver-based off-channel TX
nl80211: interface wlp0s20u2 in phy phy6
nl80211: Set mode ifindex 9 iftype 3 (AP)
nl80211: Setup AP(wlp0s20u2) - device_ap_sme=1 use_monitor=1
nl80211: Enable Probe Request reporting nl_preq=0x6e64d0
nl80211: Register frame type=0x40 nl_handle=0x6e64d0 match=
nl80211: Add own interface ifindex 9
nl80211: if_indices[16]: 9
phy: phy6
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
wlp0s20u2: interface state UNINITIALIZED->COUNTRY_UPDATE
Previous country code 00, new country code BE
Continue interface setup after channel list update
ctrl_iface not configured!
random: Got 20/20 bytes from /dev/random
Channel list update timeout - try to continue anyway
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 160 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
hw vht capab: 0x0, conf vht capab: 0x0
DFS support is enabled
Completing interface initialization
Mode: IEEE 802.11a Channel: 48 Frequency: 5240 MHz
DFS chan_idx seems wrong; num-ch: 37 ch-no: -6 conf-ch-no: 48 11n: 1 sec-ch: 0 vht-oper-width: 1
Available channel: 34
Available channel: 36
Available channel: 38
Available channel: 40
Available channel: 42
Available channel: 44
Available channel: 46
Available channel: 48
Available channel: 52
Available channel: 56
Available channel: 60
Available channel: 64
Available channel: 100
Available channel: 104
Available channel: 108
Available channel: 112
Available channel: 116
Available channel: 120
Available channel: 124
Available channel: 128
Available channel: 132
Available channel: 136
Available channel: 140
Available channel: 149
Available channel: 153
Available channel: 157
Available channel: 161
Available channel: 165
Available channel: 0
Available channel: 30208
Available channel: 0
Available channel: 0
Available channel: 0
Available channel: 0
Available channel: 0
Available channel: 0
Available channel: 0
Interface initialization failed
wlp0s20u2: interface state COUNTRY_UPDATE->DISABLED
wlp0s20u2: AP-DISABLED
hostapd_interface_deinit_free(0x6e47f0)
hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
hostapd_interface_deinit(0x6e47f0)
hostapd_bss_deinit: deinit bss wlp0s20u2
wlp0s20u2: Deauthenticate all stations
nl80211: sta_remove -> DEL_STATION wlp0s20u2 ff:ff:ff:ff:ff:ff --> -22 (Invalid argument)
hostapd_cleanup(hapd=0x6e5a20 (wlp0s20u2))
hostapd_free_hapd_data: Interface wlp0s20u2 wasn't started
hostapd_interface_deinit_free: driver=0x47b960 drv_priv=0x6e6850 -> hapd_deinit
nl80211: Skip disabling of Probe Request reporting nl_preq=0x8888888888e6ec59 while in AP mode
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=9)
netlink: Operstate: ifindex=9 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211: Set mode ifindex 9 iftype 2 (STATION)
nl80211: Teardown AP(wlp0s20u2) - device_ap_sme=1 use_monitor=1
nl80211: Disable Probe Request reporting nl_preq=0x8888888888e6ec59
hostapd_interface_free(0x6e47f0)
hostapd_interface_free: free hapd 0x6e5a20
hostapd_cleanup_iface(0x6e47f0)
hostapd_cleanup_iface_partial(0x6e47f0)
hostapd_cleanup_iface: free iface=0x6e47f0