Beelink GS1 boot logs

gistfile1.txt

[62]HELLO! BOOT0 is starting!
[66]boot0 commit : 6e906496ae7186126cfdade189def3128c9f3f79

[84]PMU: AXP806
[87]vdd-sys vol:980mv
[91]set pll start
[93]set pll end
[95]rtc[0] value = 0x00000000
[98]rtc[1] value = 0x00000000
[101]rtc[2] value = 0x00000000
[104]rtc[3] value = 0x00000000
[107]rtc[4] value = 0x00000000
[110]rtc[5] value = 0x00000000
[113]DRAM VERSION IS V2_5
[116]PMU:Set DDR Vol 1200mV OK.
[119]DRAM CLK =744 MHZ
[121]DRAM Type =7 (3:DDR3,4:DDR4,6:LPDDR2,7:LPDDR3)
[126]DRAM zq value: 003b3bfb
[133]IPRD=00710071--PGCR0=00000f5d--PLL=b0003d00
[138]DRAM SIZE =2048 M,para1 = 000030fa,para2 = 08001000
[149]DRAM simple test OK.
[152]dram size =2048
[155]card no is 2
[156]sdcard 2 line count 8
[159][mmc]: mmc driver ver 2017-03-14 13:56
[163][mmc]: mmc 2 bias 00000004
[172][mmc]: ***Try MMC card 2***
[185][mmc]: MMC 5.0
[187][mmc]: HSDDR52/DDR50 8 bit
[190][mmc]: 50000000 Hz
[193][mmc]: 15032 MB
[195][mmc]: ***SD/MMC 2 init OK!!!***
[284]Loading boot-pkg Succeed(index=0).
[288]Entry_name        = u-boot
[303]Entry_name        = parameter
[307]Entry_name        = monitor
[310]Entry_name        = scp
[320]set arisc reset to de-assert state
[323]Entry_name        = soc-cfg
[327]Entry_name        = dtb
[331]Entry_name        = board-cfg
[334]Entry_name        = board-fex
[338]Entry_name        = esm-img
[342]Entry_name        = logo
[345]Ready to disable icache.
[348]0xffffffff 0xffffffff
[351]0xff1fffff 0xffffffff
[354]0xff0f1aff 0xffffffff
[356]0x1a1affff 0xffffff19
[359]0x1221ffff 0xffffffff
[362]0x1d1dffff 0xffffffff
INFO:    Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):7408d88
NOTICE:  BL3-1: Built : 20:42:28, Aug 29 2017
NOTICE:  BL3-1 commit: 7408d88f80cb14038350a8f55a280fd0c4caf626

INFO:    BL3-1: Initializing runtime services
ERROR:   Error initializing runtime service tspd_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x4a000000
INFO:    BL3-1: Next image spsr = 0x1d3


U-Boot 2014.07 (Sep 26 2017 - 11:03:30) Allwinner Technology

uboot commit : 7cc54180a96363596d4b1fe11cc781c48b5002f7

secure enable bit: 0
normal mode: with secure monitor
I2C:   ready
[0.412]pmbus:   ready
u0:e3c81c79
[0.412][ARISC] :arisc initialize
[0.437][ARISC] :arisc para ok
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc version: [v0.3.13]
[SCP] :sunxi-arisc driver v1.10 is starting
[0.451][ARISC] :sunxi-arisc driver startup succeeded
[0.452]PMU: AXP806
[0.452]PMU: AXP806 found
[0.452]bat_vol=0, ratio=0
axp=axp806, supply=bldo2, vol=1800
axp=, supply=, vol=0
[0.457]set power on vol to default
[0.457]dcdca_vol = 1000, onoff=1
[0.461]dcdcd_vol = 1000, onoff=1
[0.465]aldo2_vol = 3300, onoff=1
[0.469]aldo3_vol = 3300, onoff=1
[0.473]bldo2_vol = 1800, onoff=1
[0.477]cldo1_vol = 3300, onoff=1
[0.481]cldo2_vol = 3300, onoff=1
[0.485]cldo3_vol = 3300, onoff=1
[0.489]find power_sply to end
[0.493]dcdca_vol = 1100, onoff=1
[0.493]PMU: cpux 888 Mhz,AXI=296 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=150Mhz MBus=400Mhz
DRAM:  2 GiB
[0.495]fdt addr: 0xb6cce920
[0.495]gd->fdt_size: 0x18aa0
Relocation Offset is: 75d77000
gic: sec monitor mode
[box standby] read rtc = 0x0
[box standby] start_type = 0x1
[box standby] to kernel
ir boot recovery not used
[0.602][key recovery] no key press.
[0.602]power on cpu1
[0.603][cpu1]task entry
[0.603][cpu1]PowerBus = 0( 2:vBus 3:acBus other: not exist)
[0.603][cpu1]no battery exist
[0.603]start
[cpu1]drv_disp_init
[cpu1]init_clocks: finish init_clocks.
[0.612]power on cpu2
workmode = 0,storage type = 2
[0.613]MMC:      2
[0.613][mmc]: mmc driver ver 2017-09-4 10:12:00
[0.613][cpu2]task entry
[0.614][cpu1]HDMI 2.0 driver init start!
[0.614][cpu2]ready to work
[0.615][mmc]: get sdc_ex_dly_used 2, use auto tuning sdly
[cpu1]__clk_enable: clk is null.
[0.625][mmc]: card2 io is 1.8V.
[0.628][cpu1]hdmi cec clk enable failed!
[0.631][mmc]: get sdc2 sdc_tm4_hs200_max_freq 150.
[0.635][cpu1]enable ddc_scl pin
[0.639][mmc]: get sdc2 sdc_tm4_hs400_max_freq 100.
[0.642][cpu1]enable ddc_sda pin
SUNXI SD/MMC: 2[0.650][cpu1]enable hmid cec pin

[0.642][cpu2]cpu 2 enter wfi mode
[0.659][mmc]: media type 0x8000000
[0.660][mmc]: Try MMC card 2
[0.669][mmc]: host caps: 0x1ef
[0.669][mmc]: MID 000013 PSN 1c43cb6f
[0.669][mmc]: PNM R1J56L -- 0x52-31-4a-35-36
[0.673][mmc]: PRV 1.0
[0.675][mmc]: MDT m-4 y-2018
[0.677][mmc]: MMC v5.0
[0.680][mmc]: bus_width      : 8 bit
[0.683][mmc]: user capacity  : 15032 MB
[0.686][mmc]: SD/MMC 2 init OK!!!
[0.690][mmc]: Best spd md: 4-HS400, freq: 3-100000000
[0.695][mmc]: EOL Info(Rev blks): Normal
[0.698][mmc]: Wear out(type A): [0.701][mmc]: 0%-10% life time used
[0.704][mmc]: Wear out(type B): [0.707][mmc]: 0%-10% life time used
[0.710][mmc]: End mmc_init_boot
[0.713]sunxi flash init ok
used mbr [0], count = 14
[0.717]try to burn key
--------fastboot partitions--------
-total partitions:14-
-name-        -start-       -size-
bootloader  : 1000000       1000000
env         : 2000000       1000000
boot        : 3000000       2000000
system      : 5000000       60000000
verity_block: 65000000      1000000
misc        : 66000000      1000000
recovery    : 67000000      2000000
private     : 69000000      1000000
[cpu1]pwm_request: reg = 0x300a000. pwm = 1.
alog        : 6a000000      4000000
[cpu1]request pwm success, pwm = 1.
Reserve0    : 6e000000      1000000
Reserve1    : 6f000000      2000000
[cpu1]speed=200000, slave=16
Reserve2    : 71000000      1000000
cache       : 72000000      30000000
UDISK       : a2000000      0
-----------------------------------
not suppert programmer
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
misc partition found
[0.802]to be run cmd=run setargs_mmc boot_normal
mac string is 00:00:00:00:00:00
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
no item name wifi_mac in the map
sunxi storage read fail
no item name bt_mac in the map
sunxi storage read fail
no item name selinux in the map
sunxi storage read fail
no item name specialstr in the map
sunxi storage read fail
check user data form private
the user data'magic is bad
[0.855][mmc]: hsddr 2-50000000
[0.856][mmc]: hs200 4-150000000
[0.859][mmc]: hs400 3-100000000
[0.862][mmc]: get max-frequency ok 150000000 Hz
[0.866][mmc]: 0 0 0: 0 0 0
[0.869][mmc]: get max-frequency ok 100000000 Hz
[0.876]update dtb dram start
[0.877]update dtb dram  end
serial is: 1c000141406d347c200d
Net:   phy_mode=rgmii, phy_interface=6
eth0
Warning: failed to set MAC address

[0.891]inter uboot shell
Hit any key to stop autoboot:  0
[0.894]read partition: boot or recovery
[cpu1]drv_disp_init finish
[cpu1]hdmi hdcp not enable!
[cpu1]get format[40a] for type[4]
[cpu1]get format[20b] for type[2]
[cpu1]hdmi hpd out, force open?
[cpu1]save_int_to_kernel disp.init_disp(0x20b040a) code:<no error>
[cpu1]get hdmi config from bootparam success.
[cpu1]hdmi config: format-1 bits-0 cs-257 eotf-4
[cpu1]size=0x384000, ram_size=0x80000000, FRAME_BUFFER_SIZE=0x1000000
[0.998]end
[cpu1]advert_enable not set
[cpu1]save_string_to_kernel disp.boot_fb0(bf000000,500,2d0,20,1400,64,0,49c,2d0>
[1.007]sunxi flash read :offset 3000000, 18523903 bytes OK
[1.010][cpu1]boot logo from boot_package/toc1 item display ok
Kernel load addr 0x40080000 size 13736 KiB
Kernel command line: selinux=1 androidboot.selinux=permissive cma=64M, use it ts
RAM disk load addr 0x41000000 size 3331 KiB
[1.052]ready to boot
[1.052]check cpu power status
[1.052]cpu2 has poweroff
[1.071][cpu1]cpu 1 enter wfi mode
[1.071]cpu1 has poweroff
[1.078]prepare for kernel
[1.078]check cpu power status
[1.078]cpu2 has poweroff
[1.078]cpu1 has poweroff
[1.078][mmc]: mmc exit start
[1.087][mmc]: mmc 2 exit ok
[1.087]
Starting kernel ...

INFO:    BL3-1: Next image address = 0x40080000
INFO:    BL3-1: Next image spsr = 0x3c5
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.65 (lfk@AZW) (gcc version 4.9.3 20150113 (pre8
[    0.000000] CPU: AArch64 Processor [410fd034] revision 4
[    0.000000] Machine: sun50iw6
[    0.000000] bootconsole [earlycon0] enabled
petrel-p1:/ $ ls
Reserve0          init.environ.rc             sdcard
acct              init.rc                     seapp_contexts
cache             init.recovery.sun50iw6p1.rc selinux_version
charger           init.sun50iw6p1.rc          sepolicy
config            init.sun50iw6p1.usb.rc      service_contexts
d                 init.usb.configfs.rc        storage
data              init.usb.rc                 sunxi-ir-rx.ko
default.prop      init.zygote32.rc            sys
dev               mnt                         system
etc               nand.ko                     tmp-mksh
file_contexts.bin oem                         ueventd.rc
fivm.ko           proc                        ueventd.sun50iw6p1.rc
fstab.sun50iw6p1  property_contexts           vendor
init              root                        verity_key
init.common.rc    rsa.pk
init.debug.rc     sbin
petrel-p1:/ $