Simplify3D Configuration file for the Original Prusa i3 MK 2

Original Prusa i3 MK2.fff

<?xml version="1.0"?>
<profile name="Original Prusa i3 MK2" version="2017-07-16 09:26:29" app="S3D-Software 3.1.1">
  <baseProfile>Default</baseProfile>
  <printMaterial>PLA</printMaterial>
  <printQuality>Normal 0.2</printQuality>
  <printExtruders></printExtruders>
  <extruder name="Primary Extruder">
    <toolheadNumber>0</toolheadNumber>
    <diameter>0.4</diameter>
    <autoWidth>0</autoWidth>
    <width>0.44</width>
    <extrusionMultiplier>0.95</extrusionMultiplier>
    <useRetract>1</useRetract>
    <retractionDistance>1</retractionDistance>
    <extraRestartDistance>0</extraRestartDistance>
    <retractionZLift>0.5</retractionZLift>
    <retractionSpeed>1800</retractionSpeed>
    <useCoasting>1</useCoasting>
    <coastingDistance>0.5</coastingDistance>
    <useWipe>1</useWipe>
    <wipeDistance>2</wipeDistance>
  </extruder>
  <primaryExtruder>0</primaryExtruder>
  <layerHeight>0.2</layerHeight>
  <topSolidLayers>5</topSolidLayers>
  <bottomSolidLayers>4</bottomSolidLayers>
  <perimeterOutlines>3</perimeterOutlines>
  <printPerimetersInsideOut>1</printPerimetersInsideOut>
  <startPointOption>2</startPointOption>
  <startPointOriginX>230</startPointOriginX>
  <startPointOriginY>0</startPointOriginY>
  <startPointOriginZ>210</startPointOriginZ>
  <sequentialIslands>0</sequentialIslands>
  <spiralVaseMode>0</spiralVaseMode>
  <firstLayerHeightPercentage>100</firstLayerHeightPercentage>
  <firstLayerWidthPercentage>100</firstLayerWidthPercentage>
  <firstLayerUnderspeed>0.7</firstLayerUnderspeed>
  <useRaft>0</useRaft>
  <raftExtruder>0</raftExtruder>
  <raftLayers>3</raftLayers>
  <raftOffset>3</raftOffset>
  <raftSeparationDistance>0.14</raftSeparationDistance>
  <raftInfill>85</raftInfill>
  <disableRaftBaseLayers>0</disableRaftBaseLayers>
  <useSkirt>0</useSkirt>
  <skirtExtruder>0</skirtExtruder>
  <skirtLayers>1</skirtLayers>
  <skirtOutlines>1</skirtOutlines>
  <skirtOffset>3</skirtOffset>
  <usePrimePillar>0</usePrimePillar>
  <primePillarExtruder>999</primePillarExtruder>
  <primePillarWidth>12</primePillarWidth>
  <primePillarLocation>7</primePillarLocation>
  <primePillarSpeedMultiplier>1</primePillarSpeedMultiplier>
  <useOozeShield>0</useOozeShield>
  <oozeShieldExtruder>999</oozeShieldExtruder>
  <oozeShieldOffset>2</oozeShieldOffset>
  <oozeShieldOutlines>1</oozeShieldOutlines>
  <oozeShieldSidewallShape>1</oozeShieldSidewallShape>
  <oozeShieldSidewallAngle>30</oozeShieldSidewallAngle>
  <oozeShieldSpeedMultiplier>1</oozeShieldSpeedMultiplier>
  <infillExtruder>0</infillExtruder>
  <internalInfillPattern>Grid</internalInfillPattern>
  <externalInfillPattern>Rectilinear</externalInfillPattern>
  <infillPercentage>20</infillPercentage>
  <outlineOverlapPercentage>25</outlineOverlapPercentage>
  <infillExtrusionWidthPercentage>100</infillExtrusionWidthPercentage>
  <minInfillLength>2</minInfillLength>
  <infillLayerInterval>1</infillLayerInterval>
  <infillAngles>45,-45</infillAngles>
  <overlapInfillAngles>1</overlapInfillAngles>
  <generateSupport>0</generateSupport>
  <supportExtruder>0</supportExtruder>
  <supportInfillPercentage>15</supportInfillPercentage>
  <supportExtraInflation>0.2</supportExtraInflation>
  <denseSupportLayers>0</denseSupportLayers>
  <denseSupportInfillPercentage>75</denseSupportInfillPercentage>
  <supportLayerInterval>1</supportLayerInterval>
  <supportHorizontalPartOffset>0.15</supportHorizontalPartOffset>
  <supportUpperSeparationLayers>1</supportUpperSeparationLayers>
  <supportLowerSeparationLayers>1</supportLowerSeparationLayers>
  <supportType>1</supportType>
  <supportGridSpacing>3</supportGridSpacing>
  <maxOverhangAngle>35</maxOverhangAngle>
  <supportAngles>0,90</supportAngles>
  <temperatureController name="Primary Extruder">
    <temperatureNumber>0</temperatureNumber>
    <isHeatedBed>0</isHeatedBed>
    <relayBetweenLayers>0</relayBetweenLayers>
    <relayBetweenLoops>0</relayBetweenLoops>
    <stabilizeAtStartup>1</stabilizeAtStartup>
    <setpoint layer="1" temperature="215"/>
    <setpoint layer="2" temperature="206"/>
  </temperatureController>
  <temperatureController name="Heated Bed">
    <temperatureNumber>1</temperatureNumber>
    <isHeatedBed>1</isHeatedBed>
    <relayBetweenLayers>0</relayBetweenLayers>
    <relayBetweenLoops>0</relayBetweenLoops>
    <stabilizeAtStartup>1</stabilizeAtStartup>
    <setpoint layer="1" temperature="55"/>
  </temperatureController>
  <fanSpeed>
    <setpoint layer="1" speed="0"/>
    <setpoint layer="2" speed="100"/>
  </fanSpeed>
  <blipFanToFullPower>1</blipFanToFullPower>
  <adjustSpeedForCooling>1</adjustSpeedForCooling>
  <minSpeedLayerTime>12</minSpeedLayerTime>
  <minCoolingSpeedSlowdown>15</minCoolingSpeedSlowdown>
  <increaseFanForCooling>0</increaseFanForCooling>
  <minFanLayerTime>45</minFanLayerTime>
  <maxCoolingFanSpeed>100</maxCoolingFanSpeed>
  <increaseFanForBridging>1</increaseFanForBridging>
  <bridgingFanSpeed>100</bridgingFanSpeed>
  <use5D>1</use5D>
  <relativeEdistances>1</relativeEdistances>
  <allowEaxisZeroing>1</allowEaxisZeroing>
  <independentExtruderAxes>0</independentExtruderAxes>
  <includeM10123>0</includeM10123>
  <stickySupport>1</stickySupport>
  <applyToolheadOffsets>0</applyToolheadOffsets>
  <gcodeXoffset>0</gcodeXoffset>
  <gcodeYoffset>0</gcodeYoffset>
  <gcodeZoffset>0</gcodeZoffset>
  <overrideMachineDefinition>1</overrideMachineDefinition>
  <machineTypeOverride>0</machineTypeOverride>
  <strokeXoverride>250</strokeXoverride>
  <strokeYoverride>210</strokeYoverride>
  <strokeZoverride>200</strokeZoverride>
  <originOffsetXoverride>0</originOffsetXoverride>
  <originOffsetYoverride>0</originOffsetYoverride>
  <originOffsetZoverride>0</originOffsetZoverride>
  <homeXdirOverride>-1</homeXdirOverride>
  <homeYdirOverride>-1</homeYdirOverride>
  <homeZdirOverride>-1</homeZdirOverride>
  <flipXoverride>1</flipXoverride>
  <flipYoverride>-1</flipYoverride>
  <flipZoverride>1</flipZoverride>
  <toolheadOffsets>0,0|0,0|0,0|0,0|0,0|0,0</toolheadOffsets>
  <overrideFirmwareConfiguration>0</overrideFirmwareConfiguration>
  <firmwareTypeOverride>RepRap (Marlin/Repetier/Sprinter)</firmwareTypeOverride>
  <GPXconfigOverride>r2</GPXconfigOverride>
  <baudRateOverride>115200</baudRateOverride>
  <overridePrinterModels>0</overridePrinterModels>
  <printerModelsOverride></printerModelsOverride>
  <startingGcode>M115 U3.0.12 ; tell the printer latest firmware varsion available,M104 S[extruder0_temperature] T0 ; this will take the layer 1 temperature for extruder 0,M140 S[bed1_temperature] ; this will take the layer 1 temperature for bed 0,M190 S[bed1_temperature] ; wait for bed temp,M109 S[extruder0_temperature] T0 ; wait for extruder temp,G28 W ; home all without mesh bed level,G80 ; mesh bed leveling,G1 Y-3.0 F1000.0 ; go outside printing area,G1 X60.0 E9.0  F1000.0 ; intro line,G1 X100.0 E12.5  F1000.0 ; intro line,</startingGcode>
  <layerChangeGcode></layerChangeGcode>
  <retractionGcode></retractionGcode>
  <toolChangeGcode></toolChangeGcode>
  <endingGcode>M104 S0 ; turn off extruder,M140 S0 ; turn off bed,M107 ; turn off fan,G1 X0 Y200; home X axis,M84 ; disable motors</endingGcode>
  <exportFileFormat>gcode</exportFileFormat>
  <celebration>0</celebration>
  <celebrationSong>Random Song</celebrationSong>
  <postProcessing>{REPLACE &quot;; outer perimeter\n&quot; &quot;; outer perimeter\nM204 S800\n&quot;},{REPLACE &quot;; inner perimeter\n&quot; &quot;; inner perimeter\nM204 S1000\n&quot;},{REPLACE &quot;; solid layer\n&quot; &quot;; solid layer\nM204 S1000\n&quot;},{REPLACE &quot;; infill\n&quot; &quot;; infill\nM204 S2000\n&quot;}</postProcessing>
  <defaultSpeed>3600</defaultSpeed>
  <outlineUnderspeed>0.6</outlineUnderspeed>
  <solidInfillUnderspeed>0.6</solidInfillUnderspeed>
  <supportUnderspeed>0.8</supportUnderspeed>
  <rapidXYspeed>6000</rapidXYspeed>
  <rapidZspeed>720</rapidZspeed>
  <minBridgingArea>25</minBridgingArea>
  <bridgingExtraInflation>2</bridgingExtraInflation>
  <bridgingExtrusionMultiplier>0.8</bridgingExtrusionMultiplier>
  <bridgingSpeedMultiplier>0.75</bridgingSpeedMultiplier>
  <filamentDiameter>1.75</filamentDiameter>
  <filamentPricePerKg>46</filamentPricePerKg>
  <filamentDensity>1.25</filamentDensity>
  <useMinPrintHeight>0</useMinPrintHeight>
  <minPrintHeight>0</minPrintHeight>
  <useMaxPrintHeight>0</useMaxPrintHeight>
  <maxPrintHeight>0</maxPrintHeight>
  <useDiaphragm>0</useDiaphragm>
  <diaphragmLayerInterval>20</diaphragmLayerInterval>
  <robustSlicing>1</robustSlicing>
  <mergeAllIntoSolid>0</mergeAllIntoSolid>
  <onlyRetractWhenCrossingOutline>1</onlyRetractWhenCrossingOutline>
  <retractBetweenLayers>1</retractBetweenLayers>
  <useRetractionMinTravel>1</useRetractionMinTravel>
  <retractionMinTravel>2</retractionMinTravel>
  <retractWhileWiping>1</retractWhileWiping>
  <onlyWipeOutlines>1</onlyWipeOutlines>
  <avoidCrossingOutline>1</avoidCrossingOutline>
  <maxMovementDetourFactor>3</maxMovementDetourFactor>
  <toolChangeRetractionDistance>12</toolChangeRetractionDistance>
  <toolChangeExtraRestartDistance>-0.5</toolChangeExtraRestartDistance>
  <toolChangeRetractionSpeed>600</toolChangeRetractionSpeed>
  <allowThinWallGapFill>1</allowThinWallGapFill>
  <thinWallAllowedOverlapPercentage>20</thinWallAllowedOverlapPercentage>
  <horizontalSizeCompensation>0</horizontalSizeCompensation>
  <autoConfigureMaterial name="PLA">
    <temperatureController name="Primary Extruder">
      <temperatureNumber>0</temperatureNumber>
      <isHeatedBed>0</isHeatedBed>
      <relayBetweenLayers>0</relayBetweenLayers>
      <relayBetweenLoops>0</relayBetweenLoops>
      <stabilizeAtStartup>1</stabilizeAtStartup>
      <setpoint layer="1" temperature="215"/>
      <setpoint layer="2" temperature="206"/>
    </temperatureController>
    <globalBedTemperature>55</globalBedTemperature>
    <globalExtrusionMultiplier>0.95</globalExtrusionMultiplier>
    <fanSpeed>
      <setpoint layer="1" speed="0"/>
      <setpoint layer="2" speed="100"/>
    </fanSpeed>
  </autoConfigureMaterial>
  <autoConfigureMaterial name="ABS">
    <temperatureController name="Primary Extruder">
      <temperatureNumber>0</temperatureNumber>
      <isHeatedBed>0</isHeatedBed>
      <relayBetweenLayers>0</relayBetweenLayers>
      <relayBetweenLoops>0</relayBetweenLoops>
      <stabilizeAtStartup>1</stabilizeAtStartup>
      <setpoint layer="1" temperature="255"/>
      <setpoint layer="2" temperature="250"/>
    </temperatureController>
    <globalBedTemperature>100</globalBedTemperature>
    <globalExtrusionMultiplier>0.95</globalExtrusionMultiplier>
    <fanSpeed>
      <setpoint layer="1" speed="0"/>
      <setpoint layer="2" speed="0"/>
    </fanSpeed>
  </autoConfigureMaterial>
  <autoConfigureQuality name="Fast 0.35">
    <layerHeight>0.35</layerHeight>
    <topSolidLayers>4</topSolidLayers>
    <bottomSolidLayers>3</bottomSolidLayers>
    <perimeterOutlines>2</perimeterOutlines>
    <skirtLayers>1</skirtLayers>
    <infillPercentage>15</infillPercentage>
    <firstLayerHeightPercentage>60</firstLayerHeightPercentage>
    <firstLayerWidthPercentage>90</firstLayerWidthPercentage>
    <firstLayerUnderspeed>0.7</firstLayerUnderspeed>
    <defaultSpeed>3600</defaultSpeed>
    <outlineUnderspeed>0.6</outlineUnderspeed>
    <solidInfillUnderspeed>1</solidInfillUnderspeed>
    <supportUnderspeed>0.8</supportUnderspeed>
    <rapidXYspeed>7200</rapidXYspeed>
    <rapidZspeed>720</rapidZspeed>
    <postProcessing>{REPLACE &quot;; outer perimeter\n&quot; &quot;; outer perimeter\nM204 S800\n&quot;},{REPLACE &quot;; inner perimeter\n&quot; &quot;; inner perimeter\nM204 S1000\n&quot;},{REPLACE &quot;; solid layer\n&quot; &quot;; solid layer\nM204 S1000\n&quot;},{REPLACE &quot;; infill\n&quot; &quot;; infill\nM204 S2000\n&quot;}</postProcessing>
    <extruder name="Primary Extruder">
      <toolheadNumber>0</toolheadNumber>
      <diameter>0.4</diameter>
      <autoWidth>0</autoWidth>
      <width>0.44</width>
      <extrusionMultiplier>0.95</extrusionMultiplier>
      <useRetract>1</useRetract>
      <retractionDistance>1</retractionDistance>
      <extraRestartDistance>0</extraRestartDistance>
      <retractionZLift>0.5</retractionZLift>
      <retractionSpeed>1800</retractionSpeed>
      <useCoasting>1</useCoasting>
      <coastingDistance>0.5</coastingDistance>
      <useWipe>1</useWipe>
      <wipeDistance>2</wipeDistance>
    </extruder>
  </autoConfigureQuality>
  <autoConfigureQuality name="Normal 0.2">
    <layerHeight>0.2</layerHeight>
    <topSolidLayers>5</topSolidLayers>
    <bottomSolidLayers>4</bottomSolidLayers>
    <perimeterOutlines>3</perimeterOutlines>
    <skirtLayers>1</skirtLayers>
    <infillPercentage>20</infillPercentage>
    <firstLayerHeightPercentage>100</firstLayerHeightPercentage>
    <firstLayerWidthPercentage>100</firstLayerWidthPercentage>
    <firstLayerUnderspeed>0.7</firstLayerUnderspeed>
    <defaultSpeed>3600</defaultSpeed>
    <outlineUnderspeed>0.6</outlineUnderspeed>
    <solidInfillUnderspeed>0.6</solidInfillUnderspeed>
    <supportUnderspeed>0.8</supportUnderspeed>
    <rapidXYspeed>6000</rapidXYspeed>
    <rapidZspeed>720</rapidZspeed>
    <postProcessing>{REPLACE &quot;; outer perimeter\n&quot; &quot;; outer perimeter\nM204 S800\n&quot;},{REPLACE &quot;; inner perimeter\n&quot; &quot;; inner perimeter\nM204 S1000\n&quot;},{REPLACE &quot;; solid layer\n&quot; &quot;; solid layer\nM204 S1000\n&quot;},{REPLACE &quot;; infill\n&quot; &quot;; infill\nM204 S2000\n&quot;}</postProcessing>
    <extruder name="Primary Extruder">
      <toolheadNumber>0</toolheadNumber>
      <diameter>0.4</diameter>
      <autoWidth>0</autoWidth>
      <width>0.44</width>
      <extrusionMultiplier>0.95</extrusionMultiplier>
      <useRetract>1</useRetract>
      <retractionDistance>1</retractionDistance>
      <extraRestartDistance>0</extraRestartDistance>
      <retractionZLift>0.5</retractionZLift>
      <retractionSpeed>1800</retractionSpeed>
      <useCoasting>1</useCoasting>
      <coastingDistance>0.5</coastingDistance>
      <useWipe>1</useWipe>
      <wipeDistance>2</wipeDistance>
    </extruder>
  </autoConfigureQuality>
  <autoConfigureQuality name="Optimal 0.15">
    <layerHeight>0.15</layerHeight>
    <topSolidLayers>6</topSolidLayers>
    <bottomSolidLayers>5</bottomSolidLayers>
    <perimeterOutlines>3</perimeterOutlines>
    <skirtLayers>1</skirtLayers>
    <infillPercentage>20</infillPercentage>
    <firstLayerHeightPercentage>134</firstLayerHeightPercentage>
    <firstLayerWidthPercentage>100</firstLayerWidthPercentage>
    <firstLayerUnderspeed>0.7</firstLayerUnderspeed>
    <defaultSpeed>3600</defaultSpeed>
    <outlineUnderspeed>0.5</outlineUnderspeed>
    <solidInfillUnderspeed>0.6</solidInfillUnderspeed>
    <supportUnderspeed>0.8</supportUnderspeed>
    <rapidXYspeed>6000</rapidXYspeed>
    <rapidZspeed>720</rapidZspeed>
    <postProcessing>{REPLACE &quot;; outer perimeter\n&quot; &quot;; outer perimeter\nM204 S800\n&quot;},{REPLACE &quot;; inner perimeter\n&quot; &quot;; inner perimeter\nM204 S1000\n&quot;},{REPLACE &quot;; solid layer\n&quot; &quot;; solid layer\nM204 S1000\n&quot;},{REPLACE &quot;; infill\n&quot; &quot;; infill\nM204 S2000\n&quot;}</postProcessing>
    <extruder name="Primary Extruder">
      <toolheadNumber>0</toolheadNumber>
      <diameter>0.4</diameter>
      <autoWidth>0</autoWidth>
      <width>0.44</width>
      <extrusionMultiplier>0.95</extrusionMultiplier>
      <useRetract>1</useRetract>
      <retractionDistance>1</retractionDistance>
      <extraRestartDistance>0</extraRestartDistance>
      <retractionZLift>0.5</retractionZLift>
      <retractionSpeed>1800</retractionSpeed>
      <useCoasting>1</useCoasting>
      <coastingDistance>0.5</coastingDistance>
      <useWipe>1</useWipe>
      <wipeDistance>2</wipeDistance>
    </extruder>
  </autoConfigureQuality>
  <autoConfigureQuality name="Detail 0.1">
    <layerHeight>0.1</layerHeight>
    <topSolidLayers>7</topSolidLayers>
    <bottomSolidLayers>6</bottomSolidLayers>
    <perimeterOutlines>3</perimeterOutlines>
    <skirtLayers>1</skirtLayers>
    <infillPercentage>20</infillPercentage>
    <firstLayerHeightPercentage>200</firstLayerHeightPercentage>
    <firstLayerWidthPercentage>100</firstLayerWidthPercentage>
    <firstLayerUnderspeed>0.7</firstLayerUnderspeed>
    <defaultSpeed>3600</defaultSpeed>
    <outlineUnderspeed>0.4</outlineUnderspeed>
    <solidInfillUnderspeed>0.6</solidInfillUnderspeed>
    <supportUnderspeed>0.8</supportUnderspeed>
    <rapidXYspeed>6000</rapidXYspeed>
    <rapidZspeed>720</rapidZspeed>
    <postProcessing>{REPLACE &quot;; outer perimeter\n&quot; &quot;; outer perimeter\nM204 S800\n&quot;},{REPLACE &quot;; inner perimeter\n&quot; &quot;; inner perimeter\nM204 S1000\n&quot;},{REPLACE &quot;; solid layer\n&quot; &quot;; solid layer\nM204 S1000\n&quot;},{REPLACE &quot;; infill\n&quot; &quot;; infill\nM204 S2000\n&quot;}</postProcessing>
    <extruder name="Primary Extruder">
      <toolheadNumber>0</toolheadNumber>
      <diameter>0.4</diameter>
      <autoWidth>0</autoWidth>
      <width>0.44</width>
      <extrusionMultiplier>0.95</extrusionMultiplier>
      <useRetract>1</useRetract>
      <retractionDistance>1</retractionDistance>
      <extraRestartDistance>0</extraRestartDistance>
      <retractionZLift>0.5</retractionZLift>
      <retractionSpeed>1800</retractionSpeed>
      <useCoasting>1</useCoasting>
      <coastingDistance>0.5</coastingDistance>
      <useWipe>1</useWipe>
      <wipeDistance>2</wipeDistance>
    </extruder>
  </autoConfigureQuality>
  <autoConfigureQuality name="Ultra Detail 0.05">
    <layerHeight>0.05</layerHeight>
    <topSolidLayers>8</topSolidLayers>
    <bottomSolidLayers>7</bottomSolidLayers>
    <perimeterOutlines>4</perimeterOutlines>
    <skirtLayers>1</skirtLayers>
    <infillPercentage>25</infillPercentage>
    <firstLayerHeightPercentage>200</firstLayerHeightPercentage>
    <firstLayerWidthPercentage>100</firstLayerWidthPercentage>
    <firstLayerUnderspeed>0.7</firstLayerUnderspeed>
    <defaultSpeed>1800</defaultSpeed>
    <outlineUnderspeed>0.6</outlineUnderspeed>
    <solidInfillUnderspeed>1</solidInfillUnderspeed>
    <supportUnderspeed>1</supportUnderspeed>
    <rapidXYspeed>6000</rapidXYspeed>
    <rapidZspeed>720</rapidZspeed>
    <postProcessing>{REPLACE &quot;; outer perimeter\n&quot; &quot;; outer perimeter\nM204 S300\n&quot;},{REPLACE &quot;; inner perimeter\n&quot; &quot;; inner perimeter\nM204 S500\n&quot;},{REPLACE &quot;; solid layer\n&quot; &quot;; solid layer\nM204 S500\n&quot;},{REPLACE &quot;; infill\n&quot; &quot;; infill\nM204 S800\n&quot;}</postProcessing>
    <extruder name="Primary Extruder">
      <toolheadNumber>0</toolheadNumber>
      <diameter>0.4</diameter>
      <autoWidth>0</autoWidth>
      <width>0.44</width>
      <extrusionMultiplier>0.95</extrusionMultiplier>
      <useRetract>1</useRetract>
      <retractionDistance>1</retractionDistance>
      <extraRestartDistance>0</extraRestartDistance>
      <retractionZLift>0.5</retractionZLift>
      <retractionSpeed>1800</retractionSpeed>
      <useCoasting>1</useCoasting>
      <coastingDistance>0.5</coastingDistance>
      <useWipe>1</useWipe>
      <wipeDistance>2</wipeDistance>
    </extruder>
  </autoConfigureQuality>
</profile>

Things to do:

• Support is a bit dodgy, maybe it's generated too distant from the object or maybe the density is too low, more testing needed
• Improve quality at 0.05, possibly extrusion and retraction has to be better calibrated
• Check quality for ABS
• Add more materials

Note:

• you may need to adjust the extrusion multiplier to meet your machine needs

I have fixed speed to better match original prusa settings and raised retraction a little to reduce stringing.

Remember that you may need to check your extrusion multiplier.

Optimized retraction, speeds and accelerations

Are you able to set it up to allow drop down selection of materials like original prusa profile? I generally use the same settings but have different temps for different filaments.

Thanks for your hard work on this!

Are you able to set it up to allow drop down selection of materials like original prusa profile?

yes, currently you can select between PLA and ABS, all it changes are the temperatures but some optimization with the speeds would be needed too