gistfile1.txt

SPI stage 1 bootloader
SPI ID: c2:20:17:c2:20
header found at offset 0x2000
Image 1.2: address: 0xffffffffc0000000, header length: 192, data length: 363424
Validating data...
Starting next bootloader at 0xffffffff81000000
Board type: UBNT_E300

U-Boot 2013.07 (Build time: Jan 04 2018 - 17:14:08)

Octeon unique ID: 08c000318819f31e0548
N0.LMC0 Configuration Completed: 1024 MB
Warning: Board descriptor tuple not found in eeprom, using defaults
Core clock: 1000 MHz, IO clock: 400 MHz, DDR clock: 533 MHz (1066 Mhz DDR)
Start hw_watchdog_start!
Stop hw_watchdog_start!
Base DRAM address used by u-boot: 0x4fc00000, size: 0x400000
DRAM: 1 GiB
Clearing DRAM...... done

SF: Detected MX25L6405D with page size 256 Bytes, erase size 4 KiB, total 8 MiB
Found valid SPI bootloader at offset: 0x5c000, size: 1438728 bytes
Found valid SPI bootloader at offset: 0x200000, size: 1438728 bytes
Loading bootloader from SPI offset 0x200000, size: 1438728 bytes


U-Boot 2013.07 (UBNT Build Version: e300_003_6be37) (Jun 05 2019 - 08:57:57)

Octeon unique ID: 08c000318819f31e0548
Using DRAM size from environment: 1024 MBytes
Core clock: 1000 MHz, IO clock: 400 MHz, DDR clock: 533 MHz (1066 Mhz DDR)
Base DRAM address used by u-boot: 0x4f000000, size: 0x1000000
DRAM: 1 GiB
Clearing DRAM...... done
SF: Detected MX25L6405D with page size 256 Bytes, erase size 4 KiB, total 8 MiB
SF: Detected MX25L6405D with page size 256 Bytes, erase size 4 KiB, total 8 MiB



UBNT_E300 r1:0, r2:14, serial #: FCECDA03BF17
MPR 13-02427-14
Loading bootloader from SPI offset 0x200000, size: 1438728 bytes


U-Boot 2013.07 (UBNT Build Version: e300_003_6be37) (Jun 05 2019 - 08:57:57)

Octeon unique ID: 08c000318819f31e0548
Using DRAM size from environment: 1024 MBytes
Core clock: 1000 MHz, IO clock: 400 MHz, DDR clock: 533 MHz (1066 Mhz DDR)
Base DRAM address used by u-boot: 0x4f000000, size: 0x1000000
DRAM: 1 GiB
Clearing DRAM...... done
SF: Detected MX25L6405D with page size 256 Bytes, erase size 4 KiB, total 8 MiB
SF: Detected MX25L6405D with page size 256 Bytes, erase size 4 KiB, total 8 MiB



UBNT_E300 r1:0, r2:14, serial #: FCECDA03BF17
MPR 13-02427-14
Flash boot bus region not enabled, skipping NOR flash config
DLM0: QSGMII ports selected
DLM1: mini-PCIe slots selected
DLM2: mini-PCIe slots selected
SPI: SPI NOR enabled
MMC:   Octeon MMC/SD0: 0
PCIe: Link timeout on port 0, probably the slot is empty
PCIe: Port 1 not in PCIe mode, skipping
PCIe: Port 2 not in PCIe mode, skipping
PCI console init succeeded, 1 consoles, 1024 bytes each
Net:   octeth0, octeth1 [PRIME], octeth2, octeth3
Node 0 Interface 0 has 4 ports (QSGMII)
Node 0 Interface 1 has 4 ports (QSGMII)
Node 0 Interface 2 has 4 ports (NPI)
Node 0 Interface 3 has 4 ports (LOOP)
Node 0 Interface 4 has 1 ports (AGL)
Type the command 'usb start' to scan for USB storage devices.

Hit any key to stop autoboot:  0 
reading vmlinux.64
8812552 bytes read in 2190 ms (3.8 MiB/s)
reading vmlinux.64.md5
33 bytes read in 303 ms (0 Bytes/s)
Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x19b97e0
## Loading big-endian Linux kernel with entry point: 0xffffffff8173b840 ...
Bootloader: Done loading app on coremask:
 0xf
Starting cores:
 0xf
[    0.000000] Linux version 5.4.72 (vagrant@builder) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14741-6ccb91f578)) #0 SMP Tue Oct 27 04:32:54 2020
[    0.000000] Skipping L2 locking due to reduced L2 cache size
[    0.000000] CVMSEG size: 0 cache lines (0 bytes)
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 000d9602 (Cavium Octeon III)
[    0.000000] Checking for the multiply/shift bug... no.
[    0.000000] Checking for the daddiu bug... no.
[    0.000000] Kernel sections are not in the memory maps
[    0.000000] Wasting 278528 bytes for tracking 4352 unused pages
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Using appended Device Tree.
[    0.000000] software IO TLB: mapped [mem 0x02b0e000-0x02b4e000] (0MB)
[    0.000000] Primary instruction cache 78kB, virtually tagged, 39 way, 16 sets, linesize 128 bytes.
[    0.000000] Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes.
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000001100000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000001100000-0x0000000002ab9fff]
[    0.000000]   node   0: [mem 0x0000000002b00000-0x000000000fafffff]
[    0.000000]   node   0: [mem 0x0000000020000000-0x000000004ebfffff]
[    0.000000] Zeroed struct page in unavailable ranges: 10822 pages
[    0.000000] Initmem setup node 0 [mem 0x0000000001100000-0x000000004ebfffff]
[    0.000000] percpu: Embedded 18 pages/cpu s35872 r8192 d29664 u73728
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 247395
[    0.000000] Kernel command line:  root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait console=ttyS0,115200
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 960400K/1005288K available (6409K kernel code, 354K rwdata, 1556K rodata, 1332K init, 16677K bss, 44888K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     CONFIG_RCU_FANOUT set to non-default value of 32.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 127
[    0.000000] CIB interrupt controller probed: 800107000000e000 23
[    0.000000] CIB interrupt controller probed: 800107000000e200 12
[    0.000000] CIB interrupt controller probed: 800107000000e400 6
[    0.000000] CIB interrupt controller probed: 800107000000e600 4
[    0.000000] CIB interrupt controller probed: 800107000000e800 11
[    0.000000] CIB interrupt controller probed: 800107000000e900 11
[    0.000000] CIB interrupt controller probed: 800107000000ec00 15
[    0.000000] random: get_random_bytes called from start_kernel+0x320/0x578 with crng_init=0
[    0.337330] clocksource: OCTEON_CVMCOUNT: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.356476] Calibrating delay loop (skipped) preset value.. 2000.00 BogoMIPS (lpj=4000000)
[    0.364708] pid_max: default: 32768 minimum: 301
[    0.369405] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.376673] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.385083] Checking for the daddi bug... no.
[    0.389834] rcu: Hierarchical SRCU implementation.
[    0.394724] smp: Bringing up secondary CPUs ...
[    0.399370] SMP: Booting CPU01 (CoreId  1)...
[    0.403651] CPU1 revision is: 000d9602 (Cavium Octeon III)
[    0.404016] SMP: Booting CPU02 (CoreId  2)...
[    0.413724] CPU2 revision is: 000d9602 (Cavium Octeon III)
[    0.414065] SMP: Booting CPU03 (CoreId  3)...
[    0.423772] CPU3 revision is: 000d9602 (Cavium Octeon III)
[    0.423873] smp: Brought up 1 node, 4 CPUs
[    0.436076] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.445684] futex hash table entries: 1024 (order: 5, 131072 bytes, linear)
[    0.453102] NET: Registered protocol family 16
[    0.462678] PCIe: Initializing port 0
[    0.469520] PCIe: BIST2 FAILED for port 0 (0x0000000000000003)
[    0.635802] random: fast init done
[    2.475202] PCIe: Link timeout on port 0, probably the slot is empty
[    2.481547] PCIe: Initializing port 1
[    2.488526] PCIe: BIST FAILED for port 1 (0xffffffffffffffff)
[    4.501474] PCIe: Link timeout on port 1, probably the slot is empty
[    4.514394] SCSI subsystem initialized
[    4.518201] usbcore: registered new interface driver usbfs
[    4.523575] usbcore: registered new interface driver hub
[    4.528867] usbcore: registered new device driver usb
[    4.533853] EDAC MC: Ver: 3.0.0
[    4.537389] PCI host bridge to bus 0000:00
[    4.541354] pci_bus 0000:00: root bus resource [mem 0x1000000000000]
[    4.547659] pci_bus 0000:00: root bus resource [io  0x0000]
[    4.553213] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    4.559983] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    4.568823] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    4.575328] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[    4.585657] clocksource: Switched to clocksource OCTEON_CVMCOUNT
[    4.592246] NET: Registered protocol family 2
[    4.596882] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    4.605111] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    4.612872] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    4.620115] TCP: Hash tables configured (established 8192 bind 8192)
[    4.626422] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    4.632975] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    4.640154] NET: Registered protocol family 1
[    4.644376] PCI: CLS 0 bytes, default 128
[    4.648999] platform 1180068000000.uctl: clocks initialized.
[    4.655051] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    4.666988] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    4.672803] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    4.684375] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO driver probed.
[    4.691922] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    4.698562] printk: console [ttyS0] disabled
[    4.702713] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 45, base_baud = 25000000) is a OCTEON
[    4.712495] printk: console [ttyS0] enabled
[    4.712495] printk: console [ttyS0] enabled
[    4.720819] printk: bootconsole [early0] disabled
[    4.720819] printk: bootconsole [early0] disabled
[    4.730459] octeon_rng octeon_rng: Octeon Random Number Generator
[    4.740239] loop: module loaded
[    4.744307] spi-nor spi0.0: mx25l6405d (8192 Kbytes)
[    4.749325] 3 fixed-partitions partitions found on MTD device spi0.0
[    4.755682] Creating 3 MTD partitions on "spi0.0":
[    4.760479] 0x000000000000-0x000000300000 : "boot0"
[    4.766028] 0x000000300000-0x000000400000 : "dummy"
[    4.771509] 0x000000400000-0x000000410000 : "eeprom"
[    4.777108] spi-octeon 1070000001000.spi: OCTEON SPI bus driver
[    4.783289] libphy: mdio_octeon: probed
[    4.788168] mdio_octeon 1180000001800.mdio: Probed
[    4.793264] libphy: Fixed MDIO Bus: probed
[    4.798173] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.804722] ehci-pci: EHCI PCI platform driver
[    4.809213] ehci-platform: EHCI generic platform driver
[    4.814519] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.820719] ohci-platform: OHCI generic platform driver
[    4.826060] usbcore: registered new interface driver usb-storage
[    4.832347] i2c-octeon 1180000001000.i2c: probed
[    4.837064] octeon_wdt: Initial granularity 5 Sec
[    4.842180] EDAC DEVICE0: Giving out device to module octeon-cpu controller cache: DEV octeon_pc_edac (INTERRUPT)
[    4.852579] EDAC DEVICE1: Giving out device to module octeon-l2c controller octeon_l2c_err: DEV octeon_l2c_edac (POLLED)
[    4.863529] octeon_lmc_edac octeon_lmc_edac.0: Disabled (ECC not enabled)
[    4.895290] Interface 0 has 4 ports (SGMII)
[    4.899550] Interface 1 has 4 ports (SGMII)
[    4.904571] Interface 3 has 4 ports (LOOP)
[    4.915734] NET: Registered protocol family 10
[    4.922043] Segment Routing with IPv6
[    4.925816] NET: Registered protocol family 17
[    4.930312] 8021q: 802.1Q VLAN Support v1.8
[    4.935015] libphy: SFP I2C Bus: probed
[    4.938968] sfp sfp: Host maximum power 1.0W
[    4.943253] sfp sfp: No tx_disable pin: SFP modules will always be emitting.
[    4.950486] OF: fdt: not creating '/sys/firmware/fdt': CRC check failed
[    4.957333] Waiting for root device /dev/mmcblk0p2...
[    5.281145] sfp sfp: module 10Gtek           ASF-GE-T         rev V01  sn WTGETI20389      dc 180201  
[    8.781666] random: crng init done
[   14.321227] mmc0: new DDR MMC card at address 0001
[   14.326454] mmcblk0: mmc0:0001 SEM04G 3.69 GiB 
[   14.331151] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB
[   14.337219] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB
[   14.343233] mmcblk0rpmb: mmc0:0001 SEM04G partition 3 2.00 MiB, chardev (252:0)
[   14.351381]  mmcblk0: p1 p2
[   14.373072] VFS: Mounted root (squashfs filesystem) readonly on device 179:2.
[   14.380779] Freeing unused kernel memory: 1332K
[   14.385365] This architecture does not have kernel memory protection.
[   14.391810] Run /sbin/init as init process
[   14.769729] init: Console is alive
[   14.773262] init: - watchdog -
[   15.103862] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[   15.135145] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   15.140677] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[   15.148437] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f06d hci version 0x100 quirks 0x0000000002010010
[   15.157876] xhci-hcd xhci-hcd.0.auto: irq 44, io mem 0x1680000000000
[   15.164818] hub 1-0:1.0: USB hub found
[   15.168623] hub 1-0:1.0: 1 port detected
[   15.172812] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   15.178330] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[   15.186009] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[   15.192626] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[   15.201104] hub 2-0:1.0: USB hub found
[   15.204926] hub 2-0:1.0: 1 port detected
[   15.210946] usbcore: registered new interface driver uas
[   15.216426] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[   15.229805] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   16.289714] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[   16.315203] usb-storage 2-1:1.0: USB Mass Storage device detected
[   16.321535] scsi host0: usb-storage 2-1:1.0


[   17.330436] scsi 0:0:0:0: Direct-Access     SanDisk  Ultra Fit        1.00 PQ: 0 ANSI: 6
[   17.339405] sd 0:0:0:0: [sda] 60063744 512-byte logical blocks: (30.8 GB/28.6 GiB)
[   17.347807] sd 0:0:0:0: [sda] Write Protect is off
[   17.352888] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   17.366286]  sda: sda1
[   17.370488] sd 0:0:0:0: [sda] Attached SCSI removable disk

[   18.658527] mount_root: rootdisk overlay filesystem has not been formatted yet


[   31.560636] F2FS-fs (loop0): Found nat_bits in checkpoint
[   31.618324] F2FS-fs (loop0): Mounted with checkpoint version = 6eb89b81
[   31.625455] mount_root: overlay filesystem has not been fully initialized yet
[   31.632898] mount_root: switching to f2fs overlay
[   31.639775] overlayfs: "xino" feature enabled using 32 upper inode bits.
- config restore -
[   32.239967] urandom-seed: Seed file not found (/etc/urandom.seed)
[   32.312717] procd: - early -
[   32.315697] procd: - watchdog -
[   32.838852] procd: - watchdog -
[   32.842197] procd: - ubus -
[   32.895823] procd: - init -
Please press Enter to activate this console.


BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r14778-a13975cf24
 -----------------------------------------------------
root@(none):/# 
root@(none):/# [   33.225866] kmodloader: loading kernel modules from /etc/modules.d/*
[   33.227780] urngd: v1.0.2 started.
[   33.246287] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   33.261786] Mirror/redirect action on
[   33.269838] u32 classifier
[   33.272551]     input device check on
[   33.276233]     Actions configured
[   33.298643] xt_time: kernel timezone is -0000
[   33.312495] PPP generic driver version 2.4.2
[   33.317541] NET: Registered protocol family 24
[   33.331151] kmodloader: done loading kernel modules from /etc/modules.d/*

root@(none):/# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: lan3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:17 brd ff:ff:ff:ff:ff:ff
3: lan0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state UNKNOWN qlen 1000
    link/ether fc:ec:da:03:bf:18 brd ff:ff:ff:ff:ff:ff
4: lan1: <BROADCAST,MULTICAST> mtu 1500 qdisc fq_codel state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:19 brd ff:ff:ff:ff:ff:ff
5: lan2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:1a brd ff:ff:ff:ff:ff:ff
6: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 3a:cf:1d:2d:fb:d4 brd ff:ff:ff:ff:ff:ff
7: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 92:17:86:d3:5b:1b brd ff:ff:ff:ff:ff:ff
8: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 96:39:72:71:dd:ac brd ff:ff:ff:ff:ff:ff
9: eth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether b6:c1:00:ab:b2:ab brd ff:ff:ff:ff:ff:ff
10: loop0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether ee:e4:fb:94:6c:3f brd ff:ff:ff:ff:ff:ff
11: loop1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 02:ea:cb:26:1c:1c brd ff:ff:ff:ff:ff:ff
12: loop2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 42:d0:d9:17:44:7b brd ff:ff:ff:ff:ff:ff
13: loop3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether b6:94:f9:95:f0:5e brd ff:ff:ff:ff:ff:ff
14: bond0: <BROADCAST,MULTICAST400> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 8a:13:41:0a:db:1e brd ff:ff:ff:ff:ff:ff
15: lan3.110@lan3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN qlen 1000
    link/ether fc:ec:da:03:bf:17 brd ff:ff:ff:ff:ff:ff
16: lan3.10@lan3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN qlen 1000
    link/ether fc:ec:da:03:bf:17 brd ff:ff:ff:ff:ff:ff
19: TMP_IFB_4_SQM: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN qlen 32
    link/ether 96:02:36:a6:e7:47 brd ff:ff:ff:ff:ff:ff
root@er4:/# ip link | grep fc:ec -B 1
2: lan3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:17 brd ff:ff:ff:ff:ff:ff
3: lan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:18 brd ff:ff:ff:ff:ff:ff
4: lan1: <BROADCAST,MULTICAST> mtu 1500 qdisc fq_codel state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:19 brd ff:ff:ff:ff:ff:ff
5: lan2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether fc:ec:da:03:bf:1a brd ff:ff:ff:ff:ff:ff
--
15: lan3.110@lan3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN qlen 1000
    link/ether fc:ec:da:03:bf:17 brd ff:ff:ff:ff:ff:ff
16: lan3.10@lan3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state LOWERLAYERDOWN qlen 1000
    link/ether fc:ec:da:03:bf:17 brd ff:ff:ff:ff:ff:ff