gistfile1.txt

[0000.158] Processing in cold boot mode Bootloader 2
[0000.163] A02 Bootrom Patch rev = 63
[0000.166] Power-up reason: software reset
[0000.170] No Battery Present
[0000.173] RamCode = 0
[0000.175] Platform has Ddr4 type ram
[0000.178] max77620 disabling SD1 Remote Sense
[0000.183] Setting Ddr voltage to 1125mv
[0000.186] Serial Number of Pmic Max77663: 0x2712ae
[0000.194] Entering ramdump check
[0000.197] Get RamDumpCarveOut = 0x0
[0000.200] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.206] Last reboot was clean, booting normally!
[0000.210] Sdram initialization is successful 
[0000.214] SecureOs Carveout Base=0xff800000 Size=0x00800000
[0000.220] GSC1 Carveout Base=0xff700000 Size=0x00100000
[0000.225] GSC2 Carveout Base=0xff600000 Size=0x00100000
[0000.230] GSC3 Carveout Base=0xff500000 Size=0x00100000
[0000.235] GSC4 Carveout Base=0xff400000 Size=0x00100000
[0000.240] GSC5 Carveout Base=0xff300000 Size=0x00100000
[0000.245] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000
[0000.251] Lp0 Carveout Base=0xff2bf000 Size=0x00001000
[0000.266] RamDump Carveout Base=0xff23f000 Size=0x00080000
[0000.271] Platform-DebugCarveout: 0
[0000.275] Nck Carveout Base=0xff03f000 Size=0x00200000
[0000.280] Non secure mode. Disable rollback prevention
[0000.285] AOTAG Init Done
[0000.312] Using GPT Primary to query partitions 
[0000.317] Loading Tboot-CPU binary
[0000.366] Verifying bootloader in OdmNonSecureSBK mode
[0000.376] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.383] Bootloader downloaded successfully.
[0000.387] Downloaded Tboot-CPU binary to 0xa0000258
[0000.392] MAX77620_GPIO1 Configured.
[0000.396] MAX77620_GPIO5 Configured.
[0000.399] CPU power rail is up
[0000.402] CPU clock enabled
[0000.406] Performing RAM repair
[0000.409] Updating A64 Warmreset Address to 0xa00002e9
[0000.426] Bootloader DTB Load Address: 0x83000000
[0000.443] Kernel DTB Load Address: 0x83080000
[0000.448] Loading cboot binary
[0000.541] Verifying bootloader in OdmNonSecureSBK mode
[0000.644] Bootloader load address is 0x8010fda8, entry address is 0x80110000
[0000.651] Bootloader downloaded successfully.
[0000.655] GPT: Partition NOT found ! 
[0000.658] Find Partition via GPT Failed
[0000.662] Find Partition via PT Failed
[0000.666] function NvTbootGetBinaryOffsets: 0x1 error
[0000.670] Error in NvTbootLoadBinary: 0x1 !
[0000.674] Next binary entry address: 0x80110000 
[0000.679] BoardId: 2180
[0000.705] NvTbootI2cProbe(): error code 0x00045100 Error while read
[0000.711] Display board id is not available 
[0000.715] dram memory type is 3
[0000.719] WB0 init successful
[0000.745] Bpmp FW successfully loaded
[0000.749] Set NvDecSticky Bits
[0000.752] GSC1 address : ff700000
[0000.755] GSC2 address ff63fffc value c0edbbcc
[0000.760] GSC2 address : ff600000
[0000.764] GSC3 address : ff500000
[0000.768] GSC4 address : ff400000
[0000.771] GSC5 address : ff300000
[0000.774] GSC MC Settings done
[0000.778] TOS old plaintext Image length 65536
[0000.784] *** Secure OS image signature not verified ***
[0000.789] Loading and Validation of Secure OS Successful
[0000.794] NvTbootPackSdramParams: start. 
[0000.800] NvTbootPackSdramParams: done. 
[0000.803] Tegraboot started after 132085 us
[0000.807] Basic modules init took 292457 us
[0000.811] Sec Bootdevice Read Time = 193 ms, Read Size = 8464 KB
[0000.817] Sec Bootdevice Write Time = -1940251267 ms, Write Size = 343597383 KB
[0000.824] Next stage binary read took 12211 us
[0000.829] Carveout took 261168 us
[0000.832] CPU initialization took 125099 us
[0000.836] Total time taken by TegraBoot 690935 us

[0000.840] Starting CPU & Halting co-processor 

64b[0000.948] RamCode = 0
[0000.963] LPDDR4 Training: Read DT: Number of tables = 10
[0000.968] EMC Training (SRC-freq: 204000; DST-freq: 40800)
[0000.973] EMC Training Skipped
[0000.976] EMC Training (SRC-freq: 204000; DST-freq: 68000)
[0000.981] EMC Training Skipped
[0000.984] EMC Training (SRC-freq: 204000; DST-freq: 102000)
[0000.989] EMC Training Skipped
[0000.992] EMC Training (SRC-freq: 204000; DST-freq: 204000)
[0000.997] EMC Training Skipped
[0001.000] EMC Training (SRC-freq: 204000; DST-freq: 408000)
[0001.006] EMC Training Successful
[0001.009] EMC Training (SRC-freq: 204000; DST-freq: 665600)
[0001.015] EMC Training Successful
[0001.018] EMC Training (SRC-freq: 204000; DST-freq: 800000)
[0001.029] EMC Training Successful
[0001.032] EMC Training (SRC-freq: 204000; DST-freq: 1065600)
[0001.055] EMC Training Successful
[0001.058] EMC Training (SRC-freq: 204000; DST-freq: 1331200)
[0001.080] EMC Training Successful
[0001.083] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.102] EMC Training Successful
[0001.106] Switching to 800000 KHz Success
[0001.112] DT Write: emc-table@40800 succeeded
[0001.118] DT Write: emc-table@68000 succeeded
[0001.125] DT Write: emc-table@102000 succeeded
[0001.131] DT Write: emc-table@204000 succeeded
[0001.137] DT Write: emc-table@408000 succeeded
[0001.144] DT Write: emc-table@665600 succeeded
[0001.150] DT Write: emc-table@800000 succeeded
[0001.156] DT Write: emc-table@1065600 succeeded
[0001.163] DT Write: emc-table@1331200 succeeded
[0001.169] DT Write: emc-table@1600000 succeeded
[0001.173] LPDDR4 Training: Write DT: Number of tables = 10


U-Boot 2016.11+dfsg1-4 (Mar 27 2017 - 18:39:51 +0000)

TEGRA210
Model: NVIDIA P2371-2180
Board: NVIDIA P2371-2180
DRAM:  3.5 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
tegra_mmc_send_cmd_bounced: MMC Timeout
    Interrupt status        0x00000001
    Interrupt status enable 0xffff003b
    Interrupt signal enable 0xffff0002
    Present status          0x01fb0206
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
977 bytes read in 76 ms (11.7 KiB/s)
p2371-2180 eMMC boot options
1:      primary kernel
Enter choice: 1:        primary kernel
Retrieving file: /boot/initrd
6902654 bytes read in 209 ms (31.5 MiB/s)
Retrieving file: /boot/Image
20048144 bytes read in 507 ms (37.7 MiB/s)
append: fbcon=map:0 console=tty0 console=ttyS0,115200n8 androidboot.modem=none androidboot.serialno=P2180A00P00940c003fd androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec= nvdumper_reserved= core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootreason=pmc:software_reset,pmic:0x0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait
Retrieving file: /boot/tegra210-jetson-tx1-p2597-2180-a01-devkit.dtb
423986 bytes read in 65 ms (6.2 MiB/s)
## Flattened Device Tree blob at 82000000
   Booting using the fdt blob at 0x82000000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000082000000, end 000000008206a831

Starting kernel ...

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.96-tegra (buildbrain@mobile-u64-1072) (gcc version 4.8.2 (GCC) ) #1 SMP PREEMPT Wed Nov 9 19:42:57 PST 2016
[    0.000000] CPU: Cortex A57 Processor [411fd071] revision 1
[    0.000000] alternative: enabling workaround for ARM erratum 832075
[    0.000000] Machine: jetson_tx1
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Reserved memory: initialized node iram-carveout, compatible id nvidia,iram-carveout
[    0.000000] Tegra reserved memory:
[    0.000000] LP0:                    00000000 - 00000000
[    0.000000] Bootloader framebuffer: 00000000 - 00000000
[    0.000000] Bootloader framebuffer2: 00000000 - 00000000
[    0.000000] Framebuffer:            00000000 - 00000000
[    0.000000] 2nd Framebuffer:        00000000 - 00000000
[    0.000000] Carveout:               00000000 - 00000000
[    0.000000] Vpr:                    00000000 - 00000000
[    0.000000] Tsec:                   00000000 - 00000000
[    0.000000] Bootloader Debug Data:  00000000 - 00000000
[    0.000000] cma: CMA: reserved 16 MiB at df000000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/arch/arm64/boot/dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts
[    0.000000] DTB Build time: Nov  9 2016 19:40:03
[    0.000000] Tegra21: Speedo/IDDQ fuse revision 4
[    0.000000] Tegra21: CPU Speedo ID 7, Soc Speedo ID 0, Gpu Speedo ID 2
[    0.000000] Tegra21: CPU Process ID 0, Soc Process ID 1, Gpu Process ID 0
[    0.000000] Tegra21: CPU Speedo value 2039, Soc Speedo value 1953, Gpu Speedo value 2038
[    0.000000] Tegra21: CPU IDDQ 2016, Soc IDDQ 2076, Gpu IDDQ 2600
[    0.000000] Tegra Revision: A02 SKU: 0x17 CPU Process: 0 Core Process: 1 Bootrom patch v0x3f
[    0.000000] tegra: PLLP fixed rate: 408000000
[    0.000000] pll_x boot misc1 0x0 : expected 0x20
[    0.000000]  (comparison mask = 0xffffff)
[    0.000000] pll_c4 rates match 204000000 max sdmmc: vco=998400000 out0=998400000 out3=998400000
[    0.000000] BUG: failure at /dvs/git/dirty/git-master_linux/kernel/drivers/platform/tegra/tegra21_clocks.c:4309/tegra21_periph_clk_init()!
[    0.000000] Enter nvdumper_crash_setup_regs
[    0.000000] nvdumper_cpu_data is not initialized!
[    0.000000] Kernel panic - not syncing: BUG!
[    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.96-tegra #1
[    0.000000] Call trace:
[    0.000000] [<ffffffc000089df4>] dump_backtrace+0x0/0xf4
[    0.000000] [<ffffffc00008a0f4>] show_stack+0x14/0x1c
[    0.000000] [<ffffffc00032a59c>] dump_stack+0x20/0x28
[    0.000000] [<ffffffc0000a6fbc>] panic+0x110/0x268
[    0.000000] [<ffffffc00088b860>] tegra21_periph_clk_init+0x12c/0x230
[    0.000000] [<ffffffc0008695f4>] clk_init+0x6c/0xf4
[    0.000000] [<ffffffc00088eeb0>] tegra21_init_one_clock+0x14/0x88
[    0.000000] [<ffffffc0011901d0>] tegra21x_init_clocks+0x58/0x230
[    0.000000] [<ffffffc001156564>] tegra21x_init_early+0x24/0x80
[    0.000000] [<ffffffc001156164>] tegra_t210ref_init_early+0xc/0x14
[    0.000000] [<ffffffc001153748>] setup_arch+0xd4/0xe0
[    0.000000] [<ffffffc00114f65c>] start_kernel+0x4c/0x2a4
[    0.000000] Rebooting in 30 seconds..