Various system information about the Billion BiPAC 8800NL

BiPAC 8800NL.txt

# cat /proc/version
Linux version 2.6.30 (root@Casper-Desktop) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Mon Jun 1 17:11:27 CST 2015

# cat /proc/cpuinfo
system type             : 963168MBV_17AZZ
processor               : 0
cpu model               : Broadcom4350 V8.0
BogoMIPS                : 399.36
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : no
hardware watchpoint     : no
ASEs implemented        :
shadow register sets    : 1
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

unaligned exceptions            : 4805514
processor               : 1
cpu model               : Broadcom4350 V8.0
BogoMIPS                : 402.43
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : no
hardware watchpoint     : no
ASEs implemented        :
shadow register sets    : 1
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

unaligned exceptions            : 4805514
# cat /proc/meminfo
MemTotal:         124596 kB
MemFree:           46412 kB
Buffers:            6416 kB
Cached:            22416 kB
SwapCached:            0 kB
Active:            12236 kB
Inactive:          22364 kB
Active(anon):       5768 kB
Inactive(anon):        0 kB
Active(file):       6468 kB
Inactive(file):    22364 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:          5796 kB
Mapped:             5440 kB
Slab:              36680 kB
SReclaimable:       1188 kB
SUnreclaim:        35492 kB
PageTables:          456 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:       62296 kB
Committed_AS:      13592 kB
VmallocTotal:    1032148 kB
VmallocUsed:        6168 kB
VmallocChunk:     994488 kB

# cat /tmp/bootupmessages
<5>OS (17:11:28, Jun  1 2015)
<4>HS Serial flash device: name ID_W25X128, id 0xef18 size 16384KB
<4>963168MBV_17AZZ prom init
<6>CPU revision is: 0002a080 (Broadcom4350)
<4>DSL SDRAM reserved: 0x132000
<6>Determined physical RAM map:
<6> memory: 07ece000 @ 00000000 (usable)
<4>Zone PFN ranges:
<4>  DMA      0x00000000 -> 0x00001000
<4>  Normal   0x00001000 -> 0x00007ece
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4>    0: 0x00000000 -> 0x00007ece
<7>On node 0 totalpages: 32462
<7>free_area_init_node: node 0, pgdat 803c0fd0, node_mem_map 81000000
<7>  DMA zone: 32 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 4064 pages, LIFO batch:0
<7>  Normal zone: 222 pages used for memmap
<7>  Normal zone: 28144 pages, LIFO batch:7
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32208
<5>Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
<4>wait instruction: enabled
<4>Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
<4>Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
<6>NR_IRQS:128
<4>PID hash table entries: 512 (order: 9, 2048 bytes)
<6>console [ttyS0] enabled
<6>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
<6>Memory: 124272k/129848k available (3041k kernel code, 5404k reserved, 755k data, 152k init, 0k highmem)
<6>Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
<4>Mount-cache hash table entries: 512
<6>--Kernel Config--
<6>  SMP=1
<6>  PREEMPT=1
<6>  DEBUG_SPINLOCK=0
<6>  DEBUG_MUTEXES=0
<4>Broadcom Logger v0.1 Jun  1 2015 17:04:00
<6>CPU revision is: 0002a080 (Broadcom4350)
<4>Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
<4>Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
<6>Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
<6>Brought up 2 CPUs
<6>net_namespace: 1140 bytes
<6>NET: Registered protocol family 16
<4>Total Flash size: 16384K with 4096 sectors
<4>Flash not used for Auxillary File System
<4>Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (000091fe-000091f6=8<300)
<4>registering PCI controller with io_map_base unset
<4>registering PCI controller with io_map_base unset
<4>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<7>pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff]
<7>pci 0000:00:00.0: supports D1 D2
<6>pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
<6>pci 0000:00:00.0: PME# disabled
<7>pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
<7>pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
<6>pci 0000:01:00.0: PME# supported from D0 D3hot
<6>pci 0000:01:00.0: PME# disabled
<6>pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
<6>pci 0000:01:00.0:   IO window: disabled
<6>pci 0000:01:00.0:   MEM window: disabled
<6>pci 0000:01:00.0:   PREFETCH window: disabled
<7>PCI: Setting latency timer of device 0000:01:00.0 to 64
<4>skbFreeTask created successfully
<4>BLOG v3.0 Initialized
<4>BLOG Rule v1.0 Initialized
<4>Broadcom IQoS v0.1 Jun  1 2015 17:08:55 initialized
<4>Broadcom GBPM v0.1 Jun  1 2015 17:08:55 initialized
<6>NET: Registered protocol family 8
<6>NET: Registered protocol family 20
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP: Hash tables configured (established 4096 bind 4096)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>squashfs: version 4.0 with LZMA457 ported by BRCM
<6>fuse init (API version 7.11)
<6>msgmni has been set to 243
<6>io scheduler noop registered (default)
<7>PCI: Setting latency timer of device 0000:01:00.0 to 64
<4>Driver 'sd' needs updating - please use bus_type methods
<6>PPP generic driver version 2.4.2
<6>PPP Deflate Compression module registered
<6>PPP BSD Compression module registered
<6>NET: Registered protocol family 24
<4>bcm963xx_mtd driver v2.0
<4>File system address: 0xb8010100
<4>Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8010100,9068544]
<6>usbcore: registered new interface driver usblp
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<4>brcmboard: brcm_board_init entry
<4>SES: Button Interrupt 0x1 is enabled
<4>sesBtn_mapIntr: is_sesBtn_irq_shared=0, sesBtn_irq=1
<4>SES: LED GPIO 0x8001 is enabled
<4>PCIe: No device found - Powering down
<4>brcm_board_init: isShared=0, rstToDflt_irq=0
<6>Serial: BCM63XX driver $Revision: 3.00 $
<6>Magic SysRq enabled (type ^ h for list of supported commands)
<6>ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
<6>ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
<4>Total # RxBds=1448
<4>bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
<4>
<4>bcmPktDma_init: Broadcom Packet DMA Library initialized
<4>bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.5 Jun  1 2015 17:07:47
<4>GACT probability NOT on
<4>Mirror/redirect action on
<4>u32 classifier
<4>    input device check on
<4>    Actions configured
<6>TCP cubic registered
<6>Initializing XFRM netlink socket
<6>NET: Registered protocol family 10
<6>IPv6 over IPv4 tunneling driver
<6>NET: Registered protocol family 17
<6>NET: Registered protocol family 15
<6>Initializing MCPD Module
<6>Ebtables v2.0 registered
<6>ebt_time registered
<6>ebt_ftos registered
<6>ebt_wmm_mark registered
<6>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
<6>All bugs added by David S. Miller <davem@redhat.com>
<4>VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
<6>Freeing unused kernel memory: 152k freed
<4>chipinfo: module license 'proprietary' taints kernel.
<4>Disabling lock debugging due to kernel taint
<4>brcmchipinfo: brcm_chipinfo_init entry
<4>Broadcom Ingress QoS Module  Char Driver v0.1 Jun  1 2015 17:07:04 Registered<243>
<4>
<4>Broadcom Ingress QoS ver 0.1 initialized
<4>BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128
<4>Broadcom BPM Module Char Driver v0.1 Jun  1 2015 17:06:50 Registered<244>
<4>[NTC bpm] bpm_set_status: BPM status : enabled
<4>
<4>NBUFF v1.0 Initialized
<4>Initialized fcache state
<4>Broadcom Packet Flow Cache  Char Driver v2.2 Jun  1 2015 17:07:05 Registered<242>
<4>Created Proc FS /procfs/fcache
<4>Broadcom Packet Flow Cache registered with netdev chain
<4>Broadcom Packet Flow Cache learning via BLOG enabled.
<4>Constructed Broadcom Packet Flow Cache v2.2 Jun  1 2015 17:07:05
<4>chipId 0x631680D0
<4>Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jun  1 2015 17:06:52 Registered <241>
<4>Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
<4>FAP Soft Reset Done
<4>4ke Reset Done
<4>Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
<4>FAP Soft Reset Done
<4>4ke Reset Done
<4>FAP Debug values at 0xa5d1dfb0 0xa5d9dfb0
<4>Allocated FAP0 GSO Buffers (0xA5D2F038) : 1048576 bytes @ 0xA5E00000
<4>Allocated FAP1 GSO Buffers (0xA5DAF038) : 1048576 bytes @ 0xA5F00000
<4>Allocated FAP0 TM SDRAM Queue Storage (a5d2f03c) : 341376 bytes @ a5800000
<4>Allocated FAP1 TM SDRAM Queue Storage (a5daf03c) : 341376 bytes @ a5880000
<4>[NTC fapProto] fapReset  : Reset FAP Protocol layer
<4>fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes
<4>fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes
<4>bcmPktDma_bind: FAP Driver binding successfull
<4>[FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3960>, free <2696>, total<8192>
<4>[FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3960>, free <2696>, total<8192>
<4>[FAP0] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576>
<4>[FAP1] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576>
<4>[FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948
<4>[FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948
<4>[FAP0] GSO Buffer set to 0xA5E00000
<4>[FAP1] GSO Buffer set to 0xA5F00000
<4>[FAP0] FAP BPM Initialized.
<4>[FAP1] FAP BPM Initialized.
<4>[FAP0] FAP TM: ON
<4>[FAP1] FAP TM: ON
<4>bcmxtmcfg: bcmxtmcfg_init entry
<4>adsl: adsl_init entry
<4>Broadcom BCM63168D0 Ethernet Network Device v0.1 Jun  1 2015 17:07:33
<4>Broadcom GMAC Char Driver v0.1 Jun  1 2015 17:07:43 Registered<249>
<4>Broadcom GMAC Driver v0.1 Jun  1 2015 17:07:43 Initialized
<4>fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000
<4>ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650
<4>fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000
<4>ETH Init: Ch:1 - 200 tx BDs at 0xb0820650
<4>fapDrv_psmAlloc: wastage 8 bytes
<4>fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184
<4>ETH Init: Ch:0 - 600 rx BDs at 0xb0821910
<4>fapDrv_psmAlloc: wastage 8 bytes
<4>fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184
<4>ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910
<4>dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
<4>eth0: MAC Address: 60:03:47:26:BF:B3
<4>eth1: MAC Address: 60:03:47:26:BF:B3
<4>eth2: MAC Address: 60:03:47:26:BF:B3
<4>eth3: MAC Address: 60:03:47:26:BF:B3
<6>NComm TMS V6.80 Kernel Module loaded.
<4>[NTC arl] arlEnable : Enabled ARL binding to FAP
<4>Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Jun  1 2015 17:06:49 Registered <245>
<4>--SMP support
<4>wl: dsl_tx_pkt_flush_len=338
<4>wl: high_wmark_tot=6149
<7>PCI: Setting latency timer of device 0000:00:00.0 to 64
<4>wl: passivemode=1
<4>wl: napimode=0
<4>wl0: allocskbmode=1 currallocskbsz=512
<4>Neither SPROM nor OTP has valid image
<4>wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
<4>wl:loading /etc/wlan/bcm6362_map.bin
<4>srom rev:8
<4>wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
<4>wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L08.4
<4>dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
<4>Loading DECT Shim driver
<4>Initialize DECT Shim layer....
<4>p8021ag: p8021ag_init entry
<6>Broadcom 802.1Q VLAN Interface, v0.1