#Gcodes for my i3 style printer
#Homing, step 1 M852 S-0.0118108; G28; G0 Z8; G0 X110 Y110
#Homing, after manual touch of the bed G92 Z0; G0 Z5; G0 X0
#Gcodes for my i3 style printer
#Homing, step 1 M852 S-0.0118108; G28; G0 Z8; G0 X110 Y110
#Homing, after manual touch of the bed G92 Z0; G0 Z5; G0 X0
# This file contains common pin mappings for RAMPS (v1.3 and later) | |
# boards. RAMPS boards typically use a firmware compiled for the AVR | |
# atmega2560 (though other AVR chips are also possible). | |
# See the example.cfg file for a description of available parameters. | |
[stepper_x] | |
step_pin: ar54 | |
dir_pin: !ar55 | |
enable_pin: !ar38 | |
step_distance: .0125 | |
endstop_pin: ^ar3 | |
#endstop_pin: ^ar2 | |
position_endstop: -12 | |
position_min: -12 | |
position_max: 240 | |
homing_speed: 50 | |
[stepper_y] | |
step_pin: ar60 | |
dir_pin: ar61 | |
enable_pin: !ar56 | |
step_distance: .0125 | |
endstop_pin: ^ar14 | |
#endstop_pin: ^ar15 | |
position_endstop: -11 | |
position_min: -11 | |
position_max: 200 | |
homing_speed: 50 | |
[stepper_z] | |
step_pin: ar46 | |
dir_pin: !ar48 | |
enable_pin: !ar62 | |
step_distance: .0025 | |
endstop_pin: ^ar18 | |
#endstop_pin: ^ar19 | |
position_endstop: 0.0 | |
position_max: 200 | |
[extruder] | |
step_pin: ar26 | |
dir_pin: ar28 | |
enable_pin: !ar24 | |
step_distance: .0012 | |
nozzle_diameter: 0.600 | |
filament_diameter: 1.750 | |
heater_pin: ar10 | |
sensor_type: ATC Semitec 104GT-2 | |
sensor_pin: analog13 | |
control: pid | |
pid_Kp: 23.56 | |
pid_Ki: 1.61 | |
pid_Kd: 86.63 | |
min_temp: 0 | |
max_temp: 280 | |
#[extruder1] | |
#step_pin: ar36 | |
#dir_pin: ar34 | |
#enable_pin: !ar30 | |
#heater_pin: ar9 | |
#sensor_pin: analog15 | |
#... | |
[heater_bed] | |
heater_pin: ar8 | |
sensor_type: EPCOS 100K B57560G104F | |
sensor_pin: analog14 | |
control: watermark | |
min_temp: 0 | |
max_temp: 120 | |
[fan] | |
pin: ar9 | |
[mcu] | |
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0 | |
pin_map: arduino | |
[printer] | |
kinematics: cartesian | |
max_velocity: 300 | |
max_accel: 3000 | |
max_z_velocity: 5 | |
max_z_accel: 100 | |
# "RepRapDiscount 2004 Smart Controller" type displays | |
[display] | |
lcd_type: hd44780 | |
rs_pin: ar16 | |
e_pin: ar17 | |
d4_pin: ar23 | |
d5_pin: ar25 | |
d6_pin: ar27 | |
d7_pin: ar29 | |
encoder_pins: ^ar31, ^ar33 | |
click_pin: ^!ar35 | |
[force_move] | |
enable_force_move: True | |
# Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION | |
# extended G-Code commands. The default is false. | |