Skip to content

Instantly share code, notes, and snippets.

@ebta

ebta/Software RAID 1 setup on Ubuntu Server 20.04.md

Forked from fevangelou/Software RAID 1 setup on Ubuntu Server 20.04.md
Last active February 10, 2022 04:42
Show Gist options
  • Save ebta/d9c49cd19d7bce66d7645b8e1f0be036 to your computer and use it in GitHub Desktop.
Save ebta/d9c49cd19d7bce66d7645b8e1f0be036 to your computer and use it in GitHub Desktop.
Download ZIP
Raw
Software RAID 1 setup on Ubuntu Server 20.04.md

Create a Software RAID 1 setup for your 2-disk server on Ubuntu Server 20.04

Let's start with the basics: the official guide by Ubuntu (https://ubuntu.com/server/docs/installation-advanced) is outdated/wrong.

Now on to the solution:

  • Select "Custom storage layout" when you reach the storage step of the installer
  • If the disks have existing partitions, click on each disk under AVAILABLE DEVICES and then select REFORMAT. This will (temporarily) wipe out the partitions.
  • Now select the 1st disk to add as "boot" disk (same menu that had REFORMAT in).
  • Do the same with the 2nd disk.
  • You should now see two 1.000M bios_grub partitions created under USED DEVICES. These small partitions will be used by GRUB for booting the server.
  • Now, the trick to setup a softRAID array is to create partitions for /boot, swap and / on each disk, but WITHOUT formatting them (an as such, there won't be a mount point for now).
  • So go ahead and "Add GPT Partition" on the 1st disk, give it a 1G size and choose to leave it unformatted. Do the same for the 2nd disk. These will be the /boot partitions for the softRAID array. Under each disk on AVAILABLE DEVICES you will now see "partition 2".
  • Now we'll prepare the swap partitions. "Add GPT Partition" on the 1st disk, give it the same or half the size of your RAM (e.g. let's say 16G cause we have 16G of actual RAM) and choose to leave it unformatted. Do the same for the 2nd disk. Under each disk on AVAILABLE DEVICES you will now see "partition 3".
  • Now we'll prepare the / partitions. "Add GPT Partition" on the 1st disk, do not set a size (so it uses all available) and choose to leave it unformatted as with all others you did so far. Do the same for the 2nd disk. Under each disk on AVAILABLE DEVICES you will now see "partition 4".
  • Now click on "Create software RAID (md)" under AVAILABLE DEVICES. We'll create the first softRAID partition (md0) by selecting the two "partition 2" entries (one from each disk). Click "Save".
  • Repeat the process for md1 and select the two "partition 3" entries. Hit "Save".
  • Repeat the process for md2 and select the two "partition 4" entries. Hit "Save".
  • We now have 3 pairs of AVAILABLE DEVICES which will now format as the actual softRAID partitions. So select md0 and then "Add GPT Partition", format as EXT4 and mount on /boot.
  • Select md1 and then "Add GPT Partition", format as SWAP.
  • Select md2 and then "Add GPT Partition", format as EXT4 and mount on /.
  • All these mdX softRAID partitions will now appear under USED DEVICES and you are ready to proceed with Ubuntu's installation.
  • At the very bottom, you should now see "Done" enabled so hit it and proceed.

Discuss here: https://gist.github.com/fevangelou/2f7aa0d9b5cb42d783302727665bf80a

Check RAID configuration is Working

cat /etc/mdadm.conf

or

cat /proc/mdstat
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment