Diff results for Marlin 1.1.5 Configuration files - set up for non-3D-printer use as a motor control board

Configuration.diff

77c77
< #define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
---
> #define STRING_CONFIG_H_AUTHOR "(Ed Nisley - KE4ZNU)" // Who made the changes.
113c113
< #define BAUDRATE 250000
---
> #define BAUDRATE 115200
126c126
< //#define CUSTOM_MACHINE_NAME "3D Printer"
---
> #define CUSTOM_MACHINE_NAME "Not a 3D Printer"
130c130
< //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
---
> #define MACHINE_UUID "89647f7b-2575-4809-bc90-5396f4376e02"
225c225
< #define POWER_SUPPLY 0
---
> #define POWER_SUPPLY 1
230c230
<   //#define PS_DEFAULT_OFF
---
> #define PS_DEFAULT_OFF
285c285
< #define TEMP_SENSOR_0 1
---
> #define TEMP_SENSOR_0 4
290c290
< #define TEMP_SENSOR_BED 0
---
> #define TEMP_SENSOR_BED 4
304c304
< #define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
---
> #define TEMP_WINDOW     2       // (degC) Window around target to start the residency timer x degC early.
309c309
< #define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
---
> #define TEMP_BED_WINDOW     2       // (degC) Window around target to start the residency timer x degC early.
324,325c324,325
< #define HEATER_0_MAXTEMP 275
< #define HEATER_1_MAXTEMP 275
---
> #define HEATER_0_MAXTEMP 75
> #define HEATER_1_MAXTEMP 75
329c329
< #define BED_MAXTEMP 150
---
> #define BED_MAXTEMP 75
417,418c417,418
< #define PREVENT_COLD_EXTRUSION
< #define EXTRUDE_MINTEMP 170
---
> //#define PREVENT_COLD_EXTRUSION
> #define EXTRUDE_MINTEMP 50
422c422
< #define PREVENT_LENGTHY_EXTRUDE
---
> //#define PREVENT_LENGTHY_EXTRUDE
441,442c441,442
< #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
< #define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
---
> //#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
> //#define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
476c476
< #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
---
> //#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
490,495c490,495
< #define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
< #define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
< #define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
< #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
< #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
< #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
---
> #define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
> #define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
> #define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
> #define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
> #define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
> #define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
527c527
< #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 4000, 500 }
---
> #define DEFAULT_AXIS_STEPS_PER_UNIT   { 100, 100, 100, 100 }
534c534
< #define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
---
> #define DEFAULT_MAX_FEEDRATE          { 100, 100, 100, 100 }
542c542
< #define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
---
> #define DEFAULT_MAX_ACCELERATION      { 1000, 1000, 1000, 1000 }
552,554c552,554
< #define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
< #define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
< #define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
---
> #define DEFAULT_ACCELERATION          1000    // X, Y, Z and E acceleration for printing moves
> #define DEFAULT_RETRACT_ACCELERATION  1000    // E acceleration for retracts
> #define DEFAULT_TRAVEL_ACCELERATION   1000    // X, Y, Z acceleration for travel (non printing) moves
566,567c566,567
< #define DEFAULT_ZJERK                  0.4
< #define DEFAULT_EJERK                  5.0
---
> #define DEFAULT_ZJERK                 20.0
> #define DEFAULT_EJERK                 20.0
744c744
< #define INVERT_X_DIR false
---
> #define INVERT_X_DIR true
746c746
< #define INVERT_Z_DIR false
---
> #define INVERT_Z_DIR true
774,775c774,775
< #define X_BED_SIZE 200
< #define Y_BED_SIZE 200
---
> #define X_BED_SIZE 2000
> #define Y_BED_SIZE 2000
778,783c778,783
< #define X_MIN_POS 0
< #define Y_MIN_POS 0
< #define Z_MIN_POS 0
< #define X_MAX_POS X_BED_SIZE
< #define Y_MAX_POS Y_BED_SIZE
< #define Z_MAX_POS 200
---
> #define X_MIN_POS -X_BED_SIZE/2
> #define Y_MIN_POS -Y_BED_SIZE/2
> #define Z_MIN_POS -1000
> #define X_MAX_POS X_BED_SIZE/2
> #define Y_MAX_POS Y_BED_SIZE/2
> #define Z_MAX_POS 1000
1013c1013
< //#define EEPROM_SETTINGS // Enable for M500 and M501 commands
---
> #define EEPROM_SETTINGS // Enable for M500 and M501 commands
1023c1023
< #define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
---
> //#define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
1046,1047c1046,1047
< #define PREHEAT_1_TEMP_BED     70
< #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
---
> #define PREHEAT_1_TEMP_BED     60
> #define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
1050,1051c1050,1051
< #define PREHEAT_2_TEMP_BED    110
< #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
---
> #define PREHEAT_2_TEMP_BED     90
> #define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
1275c1275
< //#define REVERSE_ENCODER_DIRECTION
---
> #define REVERSE_ENCODER_DIRECTION
1290c1290
< //#define INDIVIDUAL_AXIS_HOMING_MENU
---
> #define INDIVIDUAL_AXIS_HOMING_MENU
1307,1308c1307,1308
< //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
< //#define LCD_FEEDBACK_FREQUENCY_HZ 1000
---
> #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 50
> #define LCD_FEEDBACK_FREQUENCY_HZ 700
1379c1379
< //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
---
> #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER

Configuration_adv.diff

65,66c65,66
<   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
<   #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
---
>   #define THERMAL_PROTECTION_PERIOD 100        // Seconds
>   #define THERMAL_PROTECTION_HYSTERESIS 5     // Degrees Celsius
77c77
<   #define WATCH_TEMP_PERIOD 20                // Seconds
---
>   #define WATCH_TEMP_PERIOD 60                // Seconds
85c85
<   #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
---
>   #define THERMAL_PROTECTION_BED_PERIOD 120    // Seconds
97c97
<   #define WATCH_BED_TEMP_PERIOD 60                // Seconds
---
>   #define WATCH_BED_TEMP_PERIOD 120                // Seconds
225c225
<  * 
---
>  *
352c352
< #define HOMING_BUMP_DIVISOR {2, 2, 4}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
---
> #define HOMING_BUMP_DIVISOR {4, 4, 4}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
374c374
< #define DEFAULT_STEPPER_DEACTIVE_TIME 120
---
> #define DEFAULT_STEPPER_DEACTIVE_TIME 0
458c458
< //#define LCD_INFO_MENU
---
> #define LCD_INFO_MENU
461c461
< //#define STATUS_MESSAGE_SCROLLING
---
> #define STATUS_MESSAGE_SCROLLING
464c464
< //#define LCD_DECIMAL_SMALL_XY
---
> #define LCD_DECIMAL_SMALL_XY
467c467
< //#define LCD_TIMEOUT_TO_STATUS 15000
---
> #define LCD_TIMEOUT_TO_STATUS 10000
562c562
<   #define XYZ_HOLLOW_FRAME
---
>   //#define XYZ_HOLLOW_FRAME
565c565
<   #define MENU_HOLLOW_FRAME
---
>   //#define MENU_HOLLOW_FRAME
573c573
<   //#define USE_SMALL_INFOFONT
---
>   #define USE_SMALL_INFOFONT
752c752
< #define TX_BUFFER_SIZE 0
---
> #define TX_BUFFER_SIZE 128

More details on my blog at http://wp.me/poZKh-77d