Aerohive AP230 boot log

ap230-1.boot.txt

U-Boot 2012.10 (Apr 27 2019 - 23:36:59)

I2C:   ready
Wait.
Done.
DEV ID= 0000cf12
REV ID= 00000000
SKU ID = 0
OTP status: eca00018
MEMC 0 DDR speed = 800MHz
Log: ddr40_phy_init.c: Configuring DDR Controller PLLs
Log: offset = 0x18010800
Log: VCO_FREQ is 1600 which is greater than 1Ghz.
Log: DDR Phy PLL polling for lock
Log: DDR Phy PLL locked.
Log: ddr40_phy_init::DDR PHY step size calibration complete.
Log: ddr40_phy_init:: Virtual VttSetup onm CONNECT=0x01CF7FFF, OVERRIDE=0x00077FFF
Log: ddr40_phy_init:: Virtual Vtt Enabled
Log: DDR Controller PLL Configuration Complete
PHY register dump after DDR PHY init
PHY register dump after mode register write
DRAM:  256 MiB
WARNING: Caches not enabled
GPIO Init ... Done
Power Input Detection: POE AT, Drive GPIO17(USB 5V enable) success
NAND:   NAND_FLASH_DEVICE_ID_ADDR = 18028194
Done that
(ONFI),  S34ML04G1, blocks per lun: 1000 lun count: 1

*WARNING* Invalid strap options for this NAND: page=1 type=2
Overriding invalid strap options: strap_type=2
128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND:   chipsize 512 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Unlocking L2 Cache ...Done
arm_clk=1000MHz, axi_clk=500MHz, apb_clk=250MHz, arm_periph_clk=500MHz
Net:   Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC1 (0x18025000)
et0: ethHw_chipAttach: Chip ID: 0xcf12; phyaddr: 0x1e
bcm_robo_attach: devid: 0x53012
bcmiproc_eth-0
MAC address is 9c5d:1246:2200

Reset TPM chip...
Hit any key to stop autoboot:  0

Loading kernel from device 0: nand0 (offset 0xa80000) ... done
Loading rootfs from device 0: nand0 (offset 0x3780000) ... done
## Booting kernel from Legacy Image at 01005000 ...
   Image Name:   Linux-3.16.36
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2581805 Bytes = 2.5 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02005000 ...
   Image Name:   uboot initramfs rootfs
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    28110848 Bytes = 26.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
Power off two PHY...
   Loading Kernel Image ... OK
OK
boot_prep_linux commandline: root=/dev/ram console=ttyS0,9600 ramdisk_size=70000 cache-sram-size=0x10000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
L2C: platform provided aux values match the hardware, so have no effect.  Please remove them.
L2C: platform provided aux values permit register corruption.
Mounting local file systems...
Do the DB init,please wait...
ah_net: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
jffs2: notice: (61) check_node_data: wrong data CRC in data node at 0x10bc3098: read 0xf215eedf, calculated 0x5716b112.
Updating system config database...
System cPOE Input Detection -> onfiAT
g update complete.
jffs2: notice: (61) check_node_data: wrong data CRC in data node at 0x17f40a94: read 0xf0f752c3, calculated 0x8cafbb63.
gmac_var_init: NAPI2_POLL mode
Jumbo disabled
Total Memory: 268435456B, Max number of active packets: 11650 cache->name: kmalloc-2304
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 10.10.80.505_e5.1.2.3 (r659762)
register sniffer device on interface eth0.
eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 10.10.80.505_e5.1.2.3 (r659762)
register sniffer device on interface eth1.
Jumbo disabled
Total Memory: 268435456B, Max number of active packets: 11650 cache->name: kmalloc-2304
Aerohive Wireless Extension 2.0.0 ... INIT!
Jumbo disabled
Jumbo disabled
Aerohive Forwarding Engine module ... INIT!
Image L7 repository version 5, checking existing L7 repository... ...
Existing L7 repository version 5
Nothing to be done or verified with L7 repository version 5

kddr enable



Welcome to Aerohive Product

ap230-1 login: