jetson-nano-uboot

[0000.126] [TegraBoot] (version 00.00.2018.01-l4t-33e7fa82)
[0000.131] Processing in cold boot mode Bootloader 2
[0000.135] A02 Bootrom Patch rev = 1023
[0000.139] Power-up reason: pmc por
[0000.142] No Battery Present
[0000.145] pmic max77620 reset reason
[0000.148] pmic max77620 NVERC : 0x40
[0000.152] RamCode = 0
[0000.154] Platform has DDR4 type RAM
[0000.157] max77620 disabling SD1 Remote Sense
[0000.161] Setting DDR voltage to 1125mv
[0000.165] Serial Number of Pmic Max77663: 0x91fc4
[0000.173] Entering ramdump check
[0000.176] Get RamDumpCarveOut = 0x0
[0000.179] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.184] Last reboot was clean, booting normally!
[0000.189] Sdram initialization is successful
[0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.256] Platform-DebugCarveout: 0
[0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.265] Non secure mode, and RB not enabled.
[0000.272] Invalid GPT Partition
[0000.287] Using BFS PT to query partitions
[0000.291] failed to load NvTbootTbootCpu from (2:0)
[0000.296] re-load NvTbootTbootCpu from (4:0)
[0000.508] Csd NumOfBlocks=60637184
[0000.567] Using GPT Primary to query partitions
[0000.576] Loading Tboot-CPU binary
[0000.957] Verifying TBC in OdmNonSecureSBK mode
[0000.967] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.974] Bootloader downloaded successfully.
[0000.978] Downloaded Tboot-CPU binary to 0xa0000258
[0000.983] MAX77620_GPIO5 configured
[0000.986] CPU power rail is up
[0000.989] CPU clock enabled
[0000.993] Performing RAM repair
[0000.996] Updating A64 Warmreset Address to 0xa00002e9
[0001.001] Loading NvTbootBootloaderDTB
[0002.324] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0002.385] Bootloader DTB Load Address: 0x83000000
[0002.390] Loading NvTbootKernelDTB
[0003.712] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0003.774] Kernel DTB Load Address: 0x83100000
[0003.782] Loading cboot binary
[0005.481] Verifying EBT in OdmNonSecureSBK mode
[0005.523] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0005.530] Bootloader downloaded successfully.
[0005.724] Using BFS PT to query partitions
[0005.728] Next binary entry address: 0x92c00258
[0005.733] BoardId: 3448
[0005.737] Overriding pmu board id with proc board id
[0005.742] Display board id is not available
[0007.254] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0007.307] /bpmp deleted
[0007.310] SC7EntryFw header found loaded at 0xff700000
[0007.501] OVR2 PMIC
[0007.503] Bpmp FW successfully loaded
[0007.520] WB0 init successfully at 0xff780000
[0007.524] Set NvDecSticky Bits
[0007.527] GSC2 address ff53fffc value c0edbbcc
[0007.534] GSC MC Settings done
[0007.540] TOS Image length 53680
[0007.543]  Monitor size 53680
[0007.545]  OS size 0
[0007.708] Secure Os AES-CMAC Verification Success!
[0007.713] TOS image cipher info: plaintext
[0007.717] Loading and Validation of Secure OS Successful
[0007.733] SC7 Entry Firmware - 0xff700000, 0x4000
[0007.737] NvTbootPackSdramParams: start.
[0007.743] NvTbootPackSdramParams: done.
[0007.746] Tegraboot started after 53279 us
[0007.750] Basic modules init took 5831622 us
[0007.754] NvTbootQspiFlashIoctl: Opcode = 1 not supported
[0007.760] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0007.765] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0007.771] Storage Device Read Time = 6804 ms, Read Size = 2306 KB
[0007.776] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0007.782] Next stage binary read took 1543988 us
[0007.786] Carveout took -1555667 us
[0007.790] CPU initialization took 2059431 us
[0007.794] Total time taken by TegraBoot 7879374 us

[0007.799] Starting CPU & Halting co-processor

64NOTICE:  BL31: v1.3(release):eca0c5e
NOTICE:  BL31: Built : 00:21:27, Mar 13 2019
ERROR:   Error initializing runtime service trusty_fast
[0007.921] RamCode = 0
[0007.925] LPDDR4 Training: Read DT: Number of tables = 2
[0007.930] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0007.943] EMC Training Successful
[0007.946] 408000 not found in DVFS table
[0007.953] RamCode = 0
[0007.956] DT Write: emc-table@204000 succeeded
[0007.961] DT Write: emc-table@1600000 succeeded
[0007.966] LPDDR4 Training: Write DT: Number of tables = 2
[0008.166]
[0008.167] Debug Init done
[0008.170] Marked DTB cacheable
[0008.172] Bootloader DTB loaded at 0x83000000
[0008.177] Marked DTB cacheable
[0008.180] Kernel DTB loaded at 0x83100000
[0008.184] DeviceTree Init done
[0008.196] Pinmux applied successfully
[0008.201] gicd_base: 0x50041000
[0008.204] gicc_base: 0x50042000
[0008.207] Interrupts Init done
[0008.211] Using base:0x60005090 & irq:208 for tick-timer
[0008.217] Using base:0x60005098 for delay-timer
[0008.221] platform_init_timer: DONE
[0008.224] Timer(tick) Init done
[0008.228] osc freq = 38400 khz
[0008.232]
[0008.233] welcome to cboot
[0008.236]
[0008.237] Cboot Version: 00.00.2018.01-t210-f76b856b
[0008.242] calling constructors
[0008.245] initializing heap
[0008.248] initializing threads
[0008.250] initializing timers
[0008.253] creating bootstrap completion thread
[0008.258] top of bootstrap2()
[0008.261] CPU: ARM Cortex A57
[0008.263] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0008.268] initializing platform
[0008.271] Scratch reg 37 & 271 initial value set..
[0008.278] cboot:secure-pmc present
[0008.281] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0008.285] ID LSB = 0x36, ID-CFI len = 194 bytes
[0008.290] Macronix QSPI chip present
[0008.293] SPI device register
[0008.296] init boot device
[0008.299] allocating memory for boot device(SPI)
[0008.303] registering boot device
[0008.313] sdmmc node status = okay
[0008.316] sdcard instance = 0
[0008.319] sdcard gpio handle 0x5d
[0008.322] sdcard gpio pin 0xc9
[0008.325] sdcard gpio flags 0x0
[0008.328] vmmc-supply 0x9d
[0008.331] Instance: 0
[0008.333] Allocating memory for context
[0008.337] enabling clock
[0008.339] sd card init
[0008.341] Check card present and stable
[0008.345] Send command 0
[0008.362] Send command 3
[0008.366] Set RCA for the card
[0008.369] Query card specific data by command 9
[0008.375] Parse CSD data
[0008.378] Send command 7
[0008.388] Calling sd device register
[0008.391] Init sdcard
[0008.394] Allocating memory for boot device
[0008.398] Registering user device
[0008.411] Enable APE clock
[0008.414] Un-powergate APE partition
[0008.417] of_register: registering tegra_udc to of_hal
[0008.422] of_register: registering tegra_udc to of_hal
[0008.427] of_register: registering inv20628-driver to of_hal
[0008.433] of_register: registering ads1015-driver to of_hal
[0008.438] of_register: registering lp8557-bl-driver to of_hal
[0008.444] of_register: registering bq2419x_charger to of_hal
[0008.450] of_register: registering cpc to of_hal
[0008.454] of_register: registering bq27441_fuel_gauge to of_hal
[0008.466] gpio framework initialized
[0008.469] of_register: registering tca9539_gpio to of_hal
[0008.475] of_register: registering tca9539_gpio to of_hal
[0008.480] of_register: registering i2c_bus_driver to of_hal
[0008.486] of_register: registering i2c_bus_driver to of_hal
[0008.491] of_register: registering i2c_bus_driver to of_hal
[0008.497] of_register: registering i2c_bus_driver to of_hal
[0008.502] pmic framework initialized
[0008.506] of_register: registering max77620_pmic to of_hal
[0008.511] regulator framework initialized
[0008.515] of_register: registering tps65132_bl_driver to of_hal
[0008.521] initializing target
[0008.527] gpio_driver_register: register 'tegra_gpio_driver' driver
[0008.535] fixed regulator driver initialized
[0008.553] initializing OF layer
[0008.556] NCK carveout not present
[0008.559] Skipping dts_overrides
[0008.563] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.579] I2C Bus Init done
[0008.582] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.592] I2C Bus Init done
[0008.595] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.605] I2C Bus Init done
[0008.608] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.618] I2C Bus Init done
[0008.621] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.631] I2C Bus Init done
[0008.633] of_children_init: Ops found for compatible string maxim,max77620
[0008.644] max77620_init using irq 118
[0008.649] register 'maxim,max77620' pmic
[0008.653] gpio_driver_register: register 'max77620-gpio' driver
[0008.659] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.670] I2C Bus Init done
[0008.673] NCK carveout not present
[0008.676] shim_invoke: No NCT, Calling dts updates
[0008.687] Find /i2c@7000c000's alias i2c0
[0008.691] get eeprom at 1-a0, size 256, type 0
[0008.700] Find /i2c@7000c500's alias i2c2
[0008.704] get eeprom at 3-a0, size 256, type 0
[0008.708] get eeprom at 3-ae, size 256, type 0
[0008.713] pm_ids_update: Updating 1,a0, size 256, type 0
[0008.718] I2C slave not started
[0008.721] I2C write failed
[0008.724] Writing offset failed
[0008.727] eeprom_init: EEPROM read failed
[0008.731] pm_ids_update: eeprom init failed
[0008.735] pm_ids_update: Updating 3,a0, size 256, type 0
[0008.765] pm_ids_update: The pm board id is 3448-0000-200
[0008.771] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0008.779] pm_ids_update: pm id update successful
[0008.784] pm_ids_update: Updating 3,ae, size 256, type 0
[0008.814] pm_ids_update: The pm board id is 3449-0000-200
[0008.820] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0008.828] pm_ids_update: pm id update successful
[0008.858] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0008.864] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0008.872] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0008.878] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0008.886] updating /chosen/nvidia,ethernet-mac node --:--:--:--:--:--
[0008.892] Plugin Manager: Parse ODM data 0x00084000
[0008.903] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0008.923] Find /i2c@7000c000's alias i2c0
[0008.927] get eeprom at 1-a0, size 256, type 0
[0008.936] Find /i2c@7000c500's alias i2c2
[0008.939] get eeprom at 3-a0, size 256, type 0
[0008.944] get eeprom at 3-ae, size 256, type 0
[0008.948] pm_ids_update: Updating 1,a0, size 256, type 0
[0008.953] I2C slave not started
[0008.956] I2C write failed
[0008.959] Writing offset failed
[0008.962] eeprom_init: EEPROM read failed
[0008.966] pm_ids_update: eeprom init failed
[0008.970] pm_ids_update: Updating 3,a0, size 256, type 0
[0009.000] pm_ids_update: The pm board id is 3448-0000-200
[0009.007] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0009.013] pm_ids_update: pm id update successful
[0009.018] pm_ids_update: Updating 3,ae, size 256, type 0
[0009.048] pm_ids_update: The pm board id is 3449-0000-200
[0009.054] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0009.061] pm_ids_update: pm id update successful
[0009.092] Chip UID is --------------------------------
[0009.097] Add serial number:-------------------- as DT property
[0009.105] Applying platform configs
[0009.111] platform-init is not present. Skipping
[0009.116] calling apps_init()
[0009.141] Found 12 GPT partitions in "sd0"
[0009.145] Proceeding to Cold Boot
[0009.148] starting app android_boot_app
[0009.152] Device state: unlocked
[0009.155] display console init
[0009.164] could not find regulator
[0009.167] hdmi cable connected
[0009.182] edid read success
[0009.185] width = 640, height = 480, frequency = 25174825
[0009.190] width = 640, height = 480, frequency = 25174825
[0009.198] width = 1920, height = 1080, frequency = 148500000
[0009.204] Best mode Width = 640, Height = 480, freq = 25174825
[0009.212] tmds-config node not found
[0009.216] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0009.230] setting 'vdd-1v8' regulator to 1800000 micro volts
[0009.238] could not find regulator
[0009.241] could not find regulator
[0009.245] could not find regulator
[0009.273] using default cmu settings
[0009.277] dc_hdmi_enable, starting HDMI initialisation
[0009.283] dc_hdmi_enable, HDMI initialisation complete
[0009.288] list and configure display window
[0009.293] display console init completed
[0009.300] subnode volume_up is not found !
[0009.304] subnode back is not found !
[0009.307] subnode volume_down is not found !
[0009.312] subnode menu is not found !
[0009.315] Gpio keyboard init success
[0009.360] found decompressor handler: lz4-legacy
[0009.374] decompressing blob (type 1)...
[0009.408] load_bmp_blob: panelresolution=480 type=0
[0009.459] decompressor handler not found
[0009.463] load_firmware_blob: Firmware blob loaded, entries=2
[0009.469] se_aes_verify_sbk_clear: Error
[0009.473] bl_battery_charging: connected to external power supply
[0009.480] xusb is supported
[0009.486] error while finding nvidia,portmap
[0009.491] could not find regulator
[0009.994] xusb blob version 0 size 126464
[0009.998] firmware size 126464
[0010.003] Firmware timestamp: 0x59fc70d3, Version: 50.20 release
[0010.013] xhci0: 64 bytes context size, 32-bit DMA
[0010.053] usbus0: 5.0Gbps Super Speed USB v3.0
[0010.073] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0010.723] uhub0: 9 ports with 9 removable, self powered
[0011.723] failed to get HID devices
[0011.727] failed to init xhci or no usb device attached
[0011.737] device_query_partition_size: failed to open partition sd0:MSC !
[0011.744] MSC Partition not found
[0011.750] device_query_partition_size: failed to open partition sd0:USP !
[0011.757] USP partition read failed!
[0011.760] blob_init: blob-partition USP header read failed
[0011.766] android_boot Unable to update recovery partition
[0011.771] kfs_getpartname: name = LNX
[0011.775] Loading kernel from LNX
[0011.835] Verifying boot image in OdmNonSecureSBK mode
[0011.878] kernel load address: 0x80080000, size: 476960 bytes
[0011.884] ramdisk load address: 0x84100000, size: 0 bytes
[0011.889] load kernel from storage
[0011.901] decompressor handler not found
[0011.959] Successfully loaded kernel and ramdisk images
[0011.965] load_bmp_blob: panelresolution=480 type=0
[0012.038] display bmp image done
[0012.041] NCK carveout not present
[0012.044] Skipping dts_overrides
[0012.048] NCK carveout not present
[0012.051] shim_invoke: No NCT, Calling dts updates
[0012.062] Find /i2c@7000c000's alias i2c0
[0012.066] get eeprom at 1-a0, size 256, type 0
[0012.075] Find /i2c@7000c500's alias i2c2
[0012.078] get eeprom at 3-a0, size 256, type 0
[0012.083] get eeprom at 3-ae, size 256, type 0
[0012.087] pm_ids_update: Updating 1,a0, size 256, type 0
[0012.093] I2C slave not started
[0012.096] I2C write failed
[0012.098] Writing offset failed
[0012.101] eeprom_init: EEPROM read failed
[0012.105] pm_ids_update: eeprom init failed
[0012.109] pm_ids_update: Updating 3,a0, size 256, type 0
[0012.139] pm_ids_update: The pm board id is 3448-0000-200
[0012.146] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0012.154] pm_ids_update: pm id update successful
[0012.158] pm_ids_update: Updating 3,ae, size 256, type 0
[0012.188] pm_ids_update: The pm board id is 3449-0000-200
[0012.195] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0012.202] pm_ids_update: pm id update successful
[0012.233] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0012.238] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0012.246] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0012.252] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0012.261] updating /chosen/nvidia,ethernet-mac node --:--:--:--:--:--
[0012.267] Plugin Manager: Parse ODM data 0x00084000
[0012.278] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0012.291] Add serial number:-------------------- as DT property
[0012.300] "bpmp" doesn't exist, creating
[0012.306] Updated bpmp info to DTB
[0012.310] Updated initrd info to DTB
[0012.314] "proc-board" doesn't exist, creating
[0012.320] Updated board info to DTB
[0012.323] "pmu-board" doesn't exist, creating
[0012.329] Updated board info to DTB
[0012.332] "display-board" doesn't exist, creating
[0012.338] Updated board info to DTB
[0012.341] "reset" doesn't exist, creating
[0012.346] Updated reset info to DTB
[0012.349] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb6000 is_hdmi_initialised=1
[0012.388] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0012.399] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0012.410] Updated bootarg info to DTB
[0012.414] Adding uuid -------------------------------- to DT
[0012.424] device_query_partition_size: failed to open partition sd0:RP6 !
[0012.430] RP6 partition read failed!
[0012.435] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0012.441] Updated memory info to DTB
[0012.446] Updated system-lp0-disable info to DTB
[0012.454] set vdd_core voltage to 1125 mv
[0012.458] setting 'vdd-core' regulator to 1125000 micro volts
[0012.483] could not find regulator
[0012.487] Found secure-pmc; disable BPMP


U-Boot 2016.07-g541e96c (May 31 2019 - 15:44:14 -0700)

TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0