Created
April 9, 2020 20:30
-
-
Save flipy/3156df102ee970fd5c6190a37a5f8b99 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Format: Log Type - Time(microsec) - Message - Optional Info | |
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic | |
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 | |
S - IMAGE_VARIANT_STRING=DAACANAZA | |
S - OEM_IMAGE_VERSION_STRING=CRM | |
S - Boot Config, 0x00000025 | |
S - Reset status Config, 0x00000010 | |
S - Core 0 Frequency, 0 MHz | |
B - 262 - PBL, Start | |
B - 1342 - bootable_media_detect_entry, Start | |
B - 2626 - bootable_media_detect_success, Start | |
B - 2641 - elf_loader_entry, Start | |
B - 4055 - auth_hash_seg_entry, Start | |
B - 6236 - auth_hash_seg_exit, Start | |
B - 71792 - elf_segs_hash_verify_entry, Start | |
B - 194956 - PBL, End | |
B - 194981 - SBL1, Start | |
B - 287162 - pm_device_init, Start | |
D - 7 - pm_device_init, Delta | |
B - 288667 - boot_flash_init, Start | |
D - 87906 - boot_flash_init, Delta | |
B - 380890 - boot_config_data_table_init, Start | |
D - 14080 - boot_config_data_table_init, Delta - (419 Bytes) | |
B - 397678 - clock_init, Start | |
D - 7574 - clock_init, Delta | |
B - 408691 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:6 | |
B - 412104 - sbl1_ddr_set_params, Start | |
B - 417197 - cpr_init, Start | |
D - 2 - cpr_init, Delta | |
B - 421579 - Pre_DDR_clock_init, Start | |
D - 4 - Pre_DDR_clock_init, Delta | |
D - 13170 - sbl1_ddr_set_params, Delta | |
B - 434882 - pm_driver_init, Start | |
D - 2 - pm_driver_init, Delta | |
B - 505198 - sbl1_wait_for_ddr_training, Start | |
D - 28 - sbl1_wait_for_ddr_training, Delta | |
B - 521356 - Image Load, Start | |
D - 143912 - QSEE Image Loaded, Delta - (268920 Bytes) | |
B - 665698 - Image Load, Start | |
D - 2117 - SEC Image Loaded, Delta - (2048 Bytes) | |
B - 675873 - Image Load, Start | |
D - 195611 - APPSBL Image Loaded, Delta - (462999 Bytes) | |
B - 871879 - QSEE Execution, Start | |
D - 56 - QSEE Execution, Delta | |
B - 878101 - SBL1, End | |
D - 685120 - SBL1, Delta | |
S - Flash Throughput, 2089 KB/s (734386 Bytes, 351445 us) | |
S - DDR Frequency, 672 MHz | |
U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] WNC_VELOP_V2_20180718_V1.4 (Jul 18 2018 - 11:26:52) | |
smem ram ptable found: ver: 1 len: 3 | |
DRAM: 512 MiB | |
machid : 0x8010006 | |
NAND: ID = 9590dcc2 | |
Vendor = c2 | |
Device = dc | |
ONFI device found | |
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff | |
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) | |
512 MiB | |
MMC: qca_mmc: 0 | |
[devinfo_relocate] devinfo_relocate[146] malloced DEVINFO at 86ff11c0 | |
[devinfo_relocate_spec] ret: 0 , total: 262144 , CONFIG_DEVINFO_SIZE: 262144 | |
PCI0 Link Intialized | |
In: serial | |
Out: serial | |
Err: serial | |
machid: 8010006 | |
flash_type: 2 | |
#### auto_recovery #### | |
enabled:1, boot_part:1, maxpartialboots:3 | |
boot_count_buffer_size = 2048, total number = 128 | |
i=41, offset = 0x694800, last_offset = 0x694000 | |
Updating boot_count... | |
boot->Count:1 ,boot->CheckSum:20110812, offset:0x694800 | |
#### ~~~~~~~~~~~~~ #### | |
#### auto_recovery check #### | |
Hit any key to stop autoboot: 10 0 | |
Net: MAC0 addr:30:23:3:33:18:70 | |
PHY ID1: 0x4d | |
PHY ID2: 0xd0b2 | |
ipq40xx_ess_sw_init done | |
eth0 | |
(IPQ40xx) # run loadtftp | |
eth0 PHY0 Down Speed :10 Half duplex | |
eth0 PHY1 Down Speed :10 Half duplex | |
eth0 PHY2 Down Speed :10 Half duplex | |
eth0 PHY3 Down Speed :10 Half duplex | |
eth0 PHY4 up Speed :1000 Full duplex | |
Using eth0 device | |
TFTP from server 192.168.100.6; our IP address is 192.168.100.200 | |
Filename '/tftpboot/initramfs.itb'. | |
Load address: 0x81000000 | |
Loading: *T ################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
###################### | |
done | |
Bytes transferred = 5081412 (4d8944 hex) | |
## Booting kernel from FIT Image at 81000000 ... | |
Using 'config@1' configuration | |
Trying 'kernel@1' kernel subimage | |
Description: ARM OpenWrt Linux-4.19.108 | |
Type: Kernel Image | |
Compression: uncompressed | |
Data Start: 0x810000e4 | |
Data Size: 5061632 Bytes = 4.8 MiB | |
Architecture: ARM | |
OS: Linux | |
Load Address: 0x80208000 | |
Entry Point: 0x80208000 | |
Hash algo: crc32 | |
Hash value: 71ddcaa9 | |
Hash algo: sha1 | |
Hash value: 40f3e82812d5df0480fe9a6982f1bea4af76d3cf | |
Verifying Hash Integrity ... crc32+ sha1+ OK | |
## Flattened Device Tree from FIT Image at 81000000 | |
Using 'config@1' configuration | |
Trying 'fdt@1' FDT blob subimage | |
Description: ARM OpenWrt linksys_whw03v2 device tree blob | |
Type: Flat Device Tree | |
Compression: uncompressed | |
Data Start: 0x814d3e20 | |
Data Size: 17908 Bytes = 17.5 KiB | |
Architecture: ARM | |
Hash algo: crc32 | |
Hash value: 41e82cd5 | |
Hash algo: sha1 | |
Hash value: 2e74e0c96379d86995c547b905d3e7bbaae5833b | |
Verifying Hash Integrity ... crc32+ sha1+ OK | |
Booting using the fdt blob at 0x814d3e20 | |
Loading Kernel Image ... OK | |
OK | |
Loading Device Tree to 86fe8000, end 86fef5f3 ... OK | |
Andrew: mtdparts="mtdparts=nand0:1024K@0x0(0:SBL1),1024K@0x100000(0:MIBIB),1024K@0x200000(0:QSEE),512K@0x300000(0:CDT),2M@0x380000(0:APPSBL),512K@0x580000(0:ART),512K@0x600000(u_env),256K@0x680000(s_env),256K@0x6c0000(devinfo),161M@0x700000(kernel),155M@0xd00000(rootfs),161M@0xa800000(alt_kernel),155M@0xae00000(alt_rootfs),2M@0x14900000(sysdiag),181M@0x14b00000(syscfg)," | |
Device nand2 not found! | |
Using machid 0x8010006 from environment | |
Starting kernel ... | |
[ 0.000000] Booting Linux on physical CPU 0x0 | |
[ 0.000000] Linux version 4.19.108 (acalvo@gentoo) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r12738+4-9e6a27e81a)) #0 SMP Wed Apr 8 15:35:08 2020 | |
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d | |
[ 0.000000] CPU: div instructions available: patching division code | |
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache | |
[ 0.000000] OF: fdt: Machine model: Linksys WHW03 V2 (Velop) | |
[ 0.000000] Memory policy: Data cache writealloc | |
[ 0.000000] random: get_random_bytes called from start_kernel+0x7c/0x434 with crng_init=0 | |
[ 0.000000] percpu: Embedded 15 pages/cpu s29964 r8192 d23284 u61440 | |
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129408 | |
[ 0.000000] Kernel command line: root=/dev/ubiblock0_0 rootfstype=squashfs ro | |
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) | |
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) | |
[ 0.000000] Memory: 501120K/522240K available (4850K kernel code, 174K rwdata, 1328K rodata, 8192K init, 230K bss, 21120K reserved, 0K cma-reserved, 0K highmem) | |
[ 0.000000] Virtual kernel memory layout: | |
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) | |
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) | |
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) | |
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) | |
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) | |
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) | |
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (5843 kB) | |
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (8192 kB) | |
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 175 kB) | |
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 231 kB) | |
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 | |
[ 0.000000] rcu: Hierarchical RCU implementation. | |
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 | |
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). | |
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns | |
[ 0.000009] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns | |
[ 0.000023] Switching to timer-based delay loop, resolution 20ns | |
[ 0.000263] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) | |
[ 0.000282] pid_max: default: 32768 minimum: 301 | |
[ 0.000463] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.000482] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.001315] CPU: Testing write buffer coherency: ok | |
[ 0.002287] Setting up static identity map for 0x80300000 - 0x80300060 | |
[ 0.002449] rcu: Hierarchical SRCU implementation. | |
[ 0.003172] smp: Bringing up secondary CPUs ... | |
[ 0.006130] smp: Brought up 1 node, 4 CPUs | |
[ 0.006149] SMP: Total of 4 processors activated (384.00 BogoMIPS). | |
[ 0.006159] CPU: All CPU(s) started in SVC mode. | |
[ 0.010931] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 | |
[ 0.011092] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns | |
[ 0.011115] futex hash table entries: 1024 (order: 4, 65536 bytes) | |
[ 0.011368] pinctrl core: initialized pinctrl subsystem | |
[ 0.012366] NET: Registered protocol family 16 | |
[ 0.012681] DMA: preallocated 256 KiB pool for atomic coherent allocations | |
[ 0.013832] cpuidle: using governor ladder | |
[ 0.013878] cpuidle: using governor menu | |
[ 0.032358] cryptd: max_cpu_qlen set to 1000 | |
[ 0.033134] usbcore: registered new interface driver usbfs | |
[ 0.033198] usbcore: registered new interface driver hub | |
[ 0.033281] usbcore: registered new device driver usb | |
[ 0.033338] pps_core: LinuxPPS API ver. 1 registered | |
[ 0.033348] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> | |
[ 0.033375] PTP clock support registered | |
[ 0.034808] clocksource: Switched to clocksource arch_sys_counter | |
[ 0.035830] NET: Registered protocol family 2 | |
[ 0.036505] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) | |
[ 0.036548] TCP established hash table entries: 4096 (order: 2, 16384 bytes) | |
[ 0.036607] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) | |
[ 0.036697] TCP: Hash tables configured (established 4096 bind 4096) | |
[ 0.036817] UDP hash table entries: 256 (order: 1, 8192 bytes) | |
[ 0.036854] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) | |
[ 0.037086] NET: Registered protocol family 1 | |
[ 0.137624] No memory allocated for crashlog | |
[ 0.137820] workingset: timestamp_bits=14 max_order=17 bucket_order=3 | |
[ 0.142557] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
[ 0.142574] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
[ 0.148321] io scheduler noop registered | |
[ 0.148341] io scheduler deadline registered (default) | |
[ 0.149974] qcom-pcie 40000000.pci: host bridge /soc/pci@40000000 ranges: | |
[ 0.150016] qcom-pcie 40000000.pci: IO 0x40200000..0x402fffff -> 0x40200000 | |
[ 0.150044] qcom-pcie 40000000.pci: MEM 0x40300000..0x40ffffff -> 0x40300000 | |
[ 0.426375] qcom-pcie 40000000.pci: Link up | |
[ 0.426537] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00 | |
[ 0.426558] pci_bus 0000:00: root bus resource [bus 00-ff] | |
[ 0.426577] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff]) | |
[ 0.426590] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] | |
[ 0.428489] PCI: bus0: Fast back to back transfers disabled | |
[ 0.431501] PCI: bus1: Fast back to back transfers disabled | |
[ 0.431558] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] | |
[ 0.431575] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] | |
[ 0.431603] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] | |
[ 0.431680] pci 0000:00:00.0: PCI bridge to [bus 01-ff] | |
[ 0.431698] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] | |
[ 0.434136] pcieport 0000:00:00.0: AER enabled with IRQ 96 | |
[ 0.435899] bam-dma-engine 8e04000.dma: num-channels unspecified in dt | |
[ 0.435916] bam-dma-engine 8e04000.dma: num-ees unspecified in dt | |
[ 0.437172] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 | |
[ 0.437256] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 | |
[ 0.437330] tcsr 1953000.ess_tcsr: setting ess interface select = 0 | |
[ 0.437407] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 | |
[ 0.437737] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled | |
[ 0.438290] msm_serial 78af000.serial: msm_serial: detected port #0 | |
[ 0.438334] msm_serial 78af000.serial: uartclk = 1843200 | |
[ 0.438385] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM | |
[ 0.438412] msm_serial: console setup on port #0 | |
[ 1.058316] console [ttyMSM0] enabled | |
[ 1.063246] msm_serial 78b0000.serial: msm_serial: detected port #1 | |
[ 1.066596] msm_serial 78b0000.serial: uartclk = 48000000 | |
[ 1.072651] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 26, base_baud = 3000000) is a MSM | |
[ 1.078445] msm_serial: driver initialized | |
[ 1.091227] loop: module loaded | |
[ 1.092650] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xdc | |
[ 1.093790] nand: Macronix MX30LF4G18AC | |
[ 1.100440] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 | |
[ 1.104039] 15 fixed-partitions partitions found on MTD device qcom_nand.0 | |
[ 1.111610] Creating 15 MTD partitions on "qcom_nand.0": | |
[ 1.118491] 0x000000000000-0x000000100000 : "0:SBL1" | |
[ 1.125699] 0x000000100000-0x000000200000 : "0:MIBIB" | |
[ 1.130505] 0x000000200000-0x000000300000 : "0:QSEE" | |
[ 1.135484] 0x000000300000-0x000000380000 : "0:CDT" | |
[ 1.139984] 0x000000380000-0x000000580000 : "0:APPSBL" | |
[ 1.146149] 0x000000580000-0x000000600000 : "0:ART" | |
[ 1.149792] 0x000000600000-0x000000680000 : "u_env" | |
[ 1.154548] 0x000000680000-0x0000006c0000 : "s_env" | |
[ 1.159283] 0x0000006c0000-0x000000700000 : "devinfo" | |
[ 1.164030] 0x000000700000-0x00000a800000 : "kernel" | |
[ 1.177298] random: fast init done | |
[ 1.324103] 0x000000d00000-0x00000a800000 : "rootfs" | |
[ 1.474203] mtd: device 10 (rootfs) set to be root filesystem | |
[ 1.474536] mtdsplit: no squashfs found in "rootfs" | |
[ 1.478986] 0x00000a800000-0x000014900000 : "alt_kernel" | |
[ 1.638780] 0x00000ae00000-0x000014900000 : "alt_rootfs" | |
[ 1.788531] 0x000014900000-0x000014b00000 : "sysdiag" | |
[ 1.791193] 0x000014b00000-0x000020000000 : "syscfg" | |
[ 1.968870] libphy: ipq40xx_mdio: probed | |
[ 2.015114] ar40xx c000000.ess-switch: Probe failed - Missing PHYs! | |
[ 2.015530] libphy: Fixed MDIO Bus: probed | |
[ 2.024412] i2c /dev entries driver | |
[ 2.024681] i2c_qup 78b7000.i2c: using default clock-frequency 100000 | |
[ 2.030535] sdhci: Secure Digital Host Controller Interface driver | |
[ 2.034338] sdhci: Copyright(c) Pierre Ossman | |
[ 2.040462] sdhci-pltfm: SDHCI platform and OF driver helper | |
[ 2.048162] NET: Registered protocol family 10 | |
[ 2.052107] Segment Routing with IPv6 | |
[ 2.054970] NET: Registered protocol family 17 | |
[ 2.058796] 8021q: 802.1Q VLAN Support v1.8 | |
[ 2.062973] Registering SWP/SWPB emulation handler | |
[ 2.073754][ 2.089822] Freeing unused kernel memory: 8192K | |
[ 2.127493] Run /init as init process | |
[ 2.156950] init: Console is alive | |
[ 2.157162] init: - watchdog - | |
[ 2.167812] kmodloader: loading kernel modules from /etc/modules-boot.d/* | |
[ 2.177163] dwc3 8a00000.dwc3: Failed to get clk 'ref': -2 | |
[ 2.329506] dwc3 6000000.dwc3: Failed to get clk 'ref': -2 | |
[ 2.485317] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller | |
[ 2.485383] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 | |
[ 2.489938] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000000002010010 | |
[ 2.497401] xhci-hcd xhci-hcd.0.auto: irq 98, io mem 0x08a00000 | |
[ 2.507577] hub 1-0:1.0: USB hub found | |
[ 2.512602] hub 1-0:1.0: 1 port detected | |
[ 2.516743] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller | |
[ 2.520443] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 | |
[ 2.525792] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed | |
[ 2.533421] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. | |
[ 2.540466] hub 2-0:1.0: USB hub found | |
[ 2.548188] hub 2-0:1.0: 1 port detected | |
[ 2.552147] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller | |
[ 2.555824] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 | |
[ 2.561315] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010 | |
[ 2.568706] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x06000000 | |
[ 2.578858] hub 3-0:1.0: USB hub found | |
[ 2.583929] hub 3-0:1.0: 1 port detected | |
[ 2.588072] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller | |
[ 2.591798] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 | |
[ 2.597124] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed | |
[ 2.604760] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. | |
[ 2.611803] hub 4-0:1.0: USB hub found | |
[ 2.619539] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) | |
[ 2.627144] kmodloader: done loading kernel modules from /etc/modules-boot.d/* | |
[ 2.639139] init: - preinit - | |
[ 2.830576] random: crng init done | |
[ 3.054482] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready | |
[ 3.054569] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
Press the [f] key and hit [enter] to enter failsafe mode | |
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | |
[ 7.275593] procd: - early - | |
[ 7.275731] procd: - watchdog - | |
[ 7.940758] procd: - watchdog - | |
[ 7.943811] procd: - ubus - | |
[ 7.997862] procd: - init - | |
Please press Enter to activate this console. | |
[ 8.273455] kmodloader: loading kernel modules from /etc/modules.d/* | |
[ 8.282173] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc | |
[ 8.282211] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 | |
[ 8.301287] xt_time: kernel timezone is -0000 | |
[ 8.311208] urngd: v1.0.2 started. | |
[ 8.334434] PPP generic driver version 2.4.2 | |
[ 8.335466] NET: Registered protocol family 24 | |
[ 8.355019] ath10k 5.1 driver, optimized for CT firmware, probing pci device: 0x56. | |
[ 8.355767] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) | |
[ 8.362144] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 | |
[ 8.562798] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed | |
[ 8.742087] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed | |
[ 8.846135] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed | |
[ 8.957923] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed | |
[ 8.959922] ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000 | |
[ 8.965890] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 | |
[ 8.982242] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-013-b63cea875 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 00805a21 | |
[ 9.295224] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:23 crc32 0e0f75fd | |
[ 11.331810] ath10k_pci 0000:01:00.0: unsupported HTC service id: 1536 | |
[ 11.333107] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 | |
[ 11.337306] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 | |
[ 11.392581] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' | |
[ 11.393500] ath10k_pci 0000:01:00.0: wmi print 'free: 117912 iram: 12612 sram: 26276' | |
[ 11.641965] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 | |
[ 12.266919] firmware ath10k!fwcfg-ahb-a000000.wifi.txt: firmware_loading_store: map pages failed | |
[ 12.507848] firmware ath10k!QCA4019!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed | |
[ 12.612966] firmware ath10k!QCA4019!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed | |
[ 12.726159] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed | |
[ 12.727910] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 | |
[ 12.734057] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 | |
[ 12.749739] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-013-b63cea875 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 a09ca172 | |
[ 12.799856] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 0e4c84dc | |
[ 14.107241] ath10k_ahb a000000.wifi: unsupported HTC service id: 1536 | |
[ 14.108425] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 | |
[ 14.112676] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 | |
[ 14.160648] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' | |
[ 14.161605] ath10k_ahb a000000.wifi: wmi print 'free: 56568 iram: 13400 sram: 32520' | |
[ 14.307664] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 | |
[ 15.169137] firmware ath10k!fwcfg-ahb-a800000.wifi.txt: firmware_loading_store: map pages failed | |
[ 15.414074] firmware ath10k!QCA4019!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed | |
[ 15.514522] firmware ath10k!QCA4019!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed | |
[ 15.604587] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed | |
[ 15.604951] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 | |
[ 15.612476] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 | |
[ 15.627616] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-013-b63cea875 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 a09ca172 | |
[ 15.677934] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 0e4c84dc | |
[ 16.985706] ath10k_ahb a800000.wifi: unsupported HTC service id: 1536 | |
[ 16.987237] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 | |
[ 16.991150] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 | |
[ 17.039620] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' | |
[ 17.042754] ath10k_ahb a800000.wifi: wmi print 'free: 56568 iram: 13400 sram: 32520' | |
[ 17.179042] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 | |
[ 17.378342] kmodloader: done loading kernel modules from /etc/modules.d/* | |
[ 26.894143] br-lan: port 1(eth0) entered blocking state | |
[ 26.894183] br-lan: port 1(eth0) entered disabled state | |
[ 26.898588] device eth0 entered promiscuous mode | |
[ 26.906580] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready | |
[ 26.927812] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready | |
[ 27.915875] br-lan: port 1(eth0) entered blocking state | |
[ 27.916200] br-lan: port 1(eth0) entered forwarding state | |
[ 27.926848] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready | |
[ 27.937071] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment