nextvod-pdk7105-215-xbmc-12.3-Frodo-20150209.tar.xz
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.07.04 21:16:27 =~=~=~=~=~=~=~=~=~=~=~= | |
Board: STx7105-PDK [32-bit mode] | |
U-Boot 1.3.1 (Oct 6 2013 - 04:36:18) - stm23_0045 | |
DRAM: 256 MiB | |
SPI: ST M25P80 (1MiB) device (page=256,erase=4096) | |
In: serial | |
Out: serial | |
Err: serial | |
UBOOTWPDA version: 8365896 | |
swUpdate.c:1031 'Purple' LED, trying internal USB at first | |
(Re)start USB... | |
USB: scanning bus for devices... 2 USB Device(s) found | |
scanning bus for storage devices... 1 Storage Device(s) found | |
313 bytes read | |
load_uboot_env.c:31 = uboot.sh content= | |
=setenv bootargs 'console=ttyAS0,115200 rootdelay=10 root=/dev/sda2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:10:08:E2:12:06:BD phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048' | |
setenv bootcmd 'usbcfg 0; usb start; usb info; usb part; ext2load usb 0:1 80000000 uImage; bootm 80000000' | |
= end of uboot.sh = | |
Hit any key to stop autoboot: 0 | |
set usbcfg=USB_INT_REGS | |
(Re)start USB... | |
USB: scanning bus for devices... 2 USB Device(s) found | |
scanning bus for storage devices... 1 Storage Device(s) found | |
1: Hub, USB Revision 1.10 | |
- OHCI Root Hub | |
- Class: Hub | |
- PacketSize: 8 Configurations: 1 | |
- Vendor: 0x0000 Product 0x0000 Version 0.0 | |
Configuration: 1 | |
- Interfaces: 1 Self Powered 0mA | |
Interface: 0 | |
- Alternate Setting 0, Endpoints: 1 | |
- Class Hub | |
- Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms | |
2: Mass Storage, USB Revision 2.0 | |
- General USB Flash Disk TT00000000009625 | |
- Class: (from Interface) Mass Storage | |
- PacketSize: 64 Configurations: 1 | |
- Vendor: 0x090c Product 0x1000 Version 17.0 | |
Configuration: 1 | |
- Interfaces: 1 Bus Powered 500mA | |
Interface: 0 | |
- Alternate Setting 0, Endpoints: 2 | |
- Class Mass Storage, Transp. SCSI, Bulk only | |
- Endpoint 1 In Bulk MaxPacket 64 | |
- Endpoint 2 Out Bulk MaxPacket 64 | |
print_part of 0 | |
Partition Map for USB device 0 -- Partition Type: DOS | |
Partition Start Sector Num Sectors Type | |
1 63 514017 83 | |
2 514080 2008125 83 | |
3 2522205 12691350 83 | |
4 15213555 465885 5 Extd | |
5 15213618 465822 82 | |
print_part of 1 | |
## Unknown partition table | |
print_part of 2 | |
## Unknown partition table | |
print_part of 3 | |
## Unknown partition table | |
print_part of 4 | |
## Unknown partition table | |
3337547 bytes read | |
## Booting image at 80000000 ... | |
Image Name: Linux-2.6.32.61_stm24_0215 | |
Image Type: SuperH Linux Kernel Image (gzip compressed) | |
Data Size: 3337483 Bytes = 3.2 MiB | |
Load Address: 80800000 | |
Entry Point: 80801000 | |
Verifying Checksum ... OK | |
Uncompressing Kernel Image ... OK | |
CMDLen=187 | |
There is "hwaddr" keywords! Position=113 | |
Read MacAddr=24cf21b633f8 | |
[iptv_kernel]:Starting kernel console=ttyAS0,115200 rootdelay=10 root=/dev/sda2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b6:33:f8 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 - 0x00000000 - 0 ... | |
Linux version 2.6.32.61_stm24_0215 (user@NextVOD-Dev) (gcc version 4.6.3 20120613 (STMicroelectronics/Linux Base 4.6.3-111) (GCC) ) #1 PREEMPT Sun Feb 8 23:15:56 PST 2015 | |
Boot params: | |
... MOUNT_ROOT_RDONLY - 00000001 | |
... RAMDISK_FLAGS - 00000000 | |
... ORIG_ROOT_DEV - 00000200 | |
... LOADER_TYPE - 00000000 | |
... INITRD_START - 00000000 | |
... INITRD_SIZE - 00000000 | |
Booting machvec: pdk7105 | |
Node 0: start_pfn = 0x40000, low = 0x50000 | |
Zone PFN ranges: | |
Normal 0x00040000 -> 0x00050000 | |
Movable zone start PFN for each node | |
early_node_map[1] active PFN ranges | |
0: 0x00040000 -> 0x00050000 | |
STMicroelectronics PDK7105-SDK board initialisation | |
STx7105 version 3.x | |
bpa2: partition 'bigphysarea' created at 0x48000000, size 32768 kB (0x02000000 B) | |
bpa2: partition 'LMI_IO' created at 0x4a000000, size 98304 kB (0x06000000 B) | |
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 | |
Kernel command line: console=ttyAS0,115200 rootdelay=10 root=/dev/sda2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b6:33:f8 phyaddr:0,watchdog:5000 mem=256M printk=1 coprocessor_mem=4m@0x40000000,4m@0x40400000 | |
PID hash table entries: 1024 (order: 0, 4096 bytes) | |
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
PVR=04909200 CVR=60880000 PRR=00009e20 | |
I-cache : n_ways=2 n_sets=512 way_incr=16384 | |
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
D-cache : n_ways=2 n_sets=512 way_incr=16384 | |
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
Memory: 114560k/262144k available (4073k kernel code, 1577k data, 148k init) | |
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 | |
Hierarchical RCU implementation. | |
NR_IRQS:600 | |
Failed to enable clk CLKA_PLL0LS, ignoring | |
console [ttyAS0] enabled | |
sh_tmu: TMU0 used for clock events | |
sh_tmu: TMU0 used for periodic clock events | |
sh_tmu: TMU1 used as clock source | |
Calibrating delay loop... 448.51 BogoMIPS (lpj=897024) | |
Mount-cache hash table entries: 512 | |
CPU: STx7105 | |
devtmpfs: initialized | |
NET: Registered protocol family 16 | |
Configuring FLASH for boot-from-spi: boot_mode=2 | |
bio: create slab <bio-0> at 0 | |
SCSI subsystem initialized | |
usbcore: registered new interface driver usbfs | |
usbcore: registered new interface driver hub | |
usbcore: registered new device driver usb | |
DMA: Registering DMA API. | |
cfg80211: Calling CRDA to update world regulatory domain | |
Switching to clocksource TMU1 | |
NET: Registered protocol family 2 | |
IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
TCP: Hash tables configured (established 8192 bind 8192) | |
TCP reno registered | |
NET: Registered protocol family 1 | |
RPC: Registered udp transport module. | |
RPC: Registered tcp transport module. | |
RPC: Registered tcp NFSv4.1 backchannel transport module. | |
[STM]: [CPUFreq] Registered | |
Installing knfsd (copyright (C) 1996 okir@monad.swb.de). | |
Slow work thread pool: Starting up | |
Slow work thread pool: Ready | |
NTFS driver 2.1.29 [Flags: R/W]. | |
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. | |
fuse init (API version 7.13) | |
JFS: nTxBlock = 895, nTxLock = 7166 | |
msgmni has been set to 223 | |
alg: No test for stdrng (krng) | |
io scheduler noop registered | |
io scheduler anticipatory registered (default) | |
lirc_dev: IR Remote Control driver registered, major 61 | |
lirc-stm: probe found data for platform device lirc-stm | |
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode | |
lirc_dev: lirc_register_driver: sample_rate: 0 | |
STMicroelectronics LIRC driver initialized. | |
STMicroelectronics ASC driver initialized | |
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc | |
loop: module loaded | |
MiPHY driver style MiPHY3-65 probed successfully | |
MiPHY3-65, c1.5 Claimed by sata-stm | |
scsi0 : sata-stm | |
ata1: SATA max UDMA/133 irq 72 | |
ata1: SATA link down (SStatus 0 SControl 0) | |
m25p80 spi8.0: w25q80bl (1024 Kbytes) | |
Creating 1 MTD partitions on "m25p80": | |
0x000000000000-0x000000100000 : "u-boot" | |
stmmac - user ID: 0x10, Synopsys ID: 0x33 | |
No HW DMA feature register supported | |
Enhanced/Alternate descriptors | |
RX Checksum Offload Engine supported | |
TX Checksum insertion supported | |
Wake-Up On Lan supported | |
STMMAC MII Bus: probed | |
eth0: PHY ID 01018f2d at 17 IRQ 0 (0:11) active | |
nwhw_config: (eth0) setting mac address: 24:cf:21:b6:33:f8 | |
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0 | |
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller | |
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1 | |
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00 | |
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00 | |
usb usb1: configuration #1 chosen from 1 choice | |
hub 1-0:1.0: USB hub found | |
hub 1-0:1.0: 1 port detected | |
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller | |
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2 | |
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00 | |
usb usb2: configuration #1 chosen from 1 choice | |
hub 2-0:1.0: USB hub found | |
hub 2-0:1.0: 1 port detected | |
Initializing USB Mass Storage driver... | |
usbcore: registered new interface driver usb-storage | |
USB Mass Storage support registered. | |
mice: PS/2 mouse device common for all mice | |
i2c /dev entries driver | |
Linux video capture interface: v2.00 | |
Registered led device: BLUE_LED | |
Registered led device: RED_LED | |
sh_tmu: TMU0 kept as earlytimer | |
sh_tmu: TMU1 kept as earlytimer | |
usbcore: registered new interface driver usbkbd | |
usbkbd: :USB HID Boot Protocol keyboard driver | |
usbcore: registered new interface driver usbmouse | |
usbmouse: v1.6:USB HID Boot Protocol mouse driver | |
STMicroelectronics - Coprocessors st231 Init | |
st231.0 Coprocessor ------------------------------------------- | |
flags 0001 RAM start at 0xbf000000 size 0x00400000 | |
cop. addr 0x40000000 | |
Channels : Not defined | |
IRQ : not used | |
--------------------------------------------------------------- | |
st231.1 Coprocessor ------------------------------------------- | |
flags 0001 RAM start at 0xbf400000 size 0x00400000 | |
cop. addr 0x40400000 | |
Channels : Not defined | |
IRQ : not used | |
--------------------------------------------------------------- | |
DMA: Registering fdma_dmac.0 handler (16 channels). | |
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs | |
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7105_0.elf | |
DMA: Registering fdma_dmac.1 handler (16 channels). | |
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.3 | |
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs | |
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7105_1.elf | |
stm-rng hardware driver 1.0 configured | |
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.6 | |
Advanced Linux Sound Architecture Driver Version 1.0.21. | |
ALSA device list: | |
#0: STMicroelectronics STx7105 cut 3.x SOC audio subsystem | |
TCP cubic registered | |
NET: Registered protocol family 17 | |
lib80211: common routines for IEEE802.11 drivers | |
Waiting 10sec before mounting root device... | |
usb 1-1: new high speed USB device using stm-ehci and address 2 | |
usb 1-1: configuration #1 chosen from 1 choice | |
scsi1 : SCSI emulation for USB Mass Storage devices | |
stm_usb_probe: usb_phy_clk clock not found for stm-usb.1 | |
stm-ehci stm-ehci.1: STMicroelectronics EHCI Host Controller | |
stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3 | |
stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00 | |
stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00 | |
usb usb3: configuration #1 chosen from 1 choice | |
hub 3-0:1.0: USB hub found | |
hub 3-0:1.0: 1 port detected | |
stm-ohci stm-ohci.1: STMicroelectronics OHCI Host Controller | |
stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4 | |
stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00 | |
usb usb4: configuration #1 chosen from 1 choice | |
hub 4-0:1.0: USB hub found | |
hub 4-0:1.0: 1 port detected | |
scsi 1:0:0:0: Direct-Access General USB Flash Disk 1100 PQ: 0 ANSI: 0 CCS | |
sd 1:0:0:0: [sda] 15679488 512-byte logical blocks: (8.02 GB/7.47 GiB) | |
sd 1:0:0:0: [sda] Write Protect is off | |
sd 1:0:0:0: [sda] Assuming drive cache: write through | |
sd 1:0:0:0: [sda] Assuming drive cache: write through | |
sda: sda1 sda2 sda3 sda4 < sda5 > | |
sd 1:0:0:0: [sda] Assuming drive cache: write through | |
sd 1:0:0:0: [sda] Attached SCSI removable disk | |
kjournald starting. Commit interval 5 seconds | |
EXT3 FS on sda2, internal journal | |
EXT3-fs: recovery complete. | |
EXT3-fs: mounted filesystem with journal data mode. | |
VFS: Mounted root (ext3 filesystem) on device 8:2. | |
devtmpfs: mounted | |
Freeing unused kernel memory: 148k freed | |
INIT: version 2.86 booting | |
Initializing network interface... | |
eth0: device MAC address 24:cf:21:b6:33:f8 | |
No MAC Management Counters available | |
Mounting filesystems... | |
Setting up mdev... | |
Setting up front panel LEDs... | |
Initializing stmfb... | |
stmcore-display: using HDMI hotplug | |
stmcore-display: STi7105 display: probed | |
device probe found 2 display pipelines | |
requesting frm: 'component.fw', c11758ac/87019b10 | |
stm-awg: firmware: using built-in firmware component.fw | |
frm 'component.fw' successfully loaded | |
requesting frm: 'fdvo0.fw', c11758ac/87019d90 | |
stm-awg: firmware: using built-in firmware fdvo0.fw | |
frm 'fdvo0.fw' successfully loaded | |
stmfb: fb0 parameters = "1920x1080-32@60:24m:12m:ntsc-m:yuv:yuv" | |
trying to alloc 12582912 bytes (align: 0000, still needed: 12582912) from 'gfx-memory' for GFX0 auxmem | |
success: base: 4a000000, still needed: 0 | |
stmfb: fb1 parameters = "<NULL>" | |
Loading co-processor drivers... | |
Loading audio firmware... | |
copLoadFile (file /boot/audio_dts.elf) | |
ustslave: Kernel Version: 24 | |
base_address 0x40400000 | |
seeking to 0 | |
seeking to 400 | |
seeking to 5c18 | |
seeking to b058 | |
seeking to ff08 | |
seeking to 136f0 | |
seeking to 15008 | |
seeking to 15018 | |
seeking to 3bcc0 | |
seeking to 3dfb8 | |
seeking to 46558 | |
seeking to 48a58 | |
seeking to 71e68 | |
seeking to 75fe8 | |
seeking to 77878 | |
seeking to 77c88 | |
seeking to 90ef0 | |
seeking to a16c0 | |
seeking to 139f28 | |
seeking to 139ff0 | |
seeking to 13b6b0 | |
seeking to 13ed70 | |
seeking to 1427b0 | |
seeking to 145408 | |
seeking to 14b3c8 | |
seeking to 159f58 | |
seeking to 177b78 | |
seeking to 17a378 | |
seeking to 184460 | |
seeking to 18c9a8 | |
seeking to 221208 | |
seeking to 26e400 | |
seeking to 26e438 | |
seeking to 26e470 | |
seeking to 275820 | |
seeking to 275828 | |
seeking to 275830 | |
seeking to 275840 | |
seeking to 2955c0 | |
Loading video firmware... | |
copLoadFile (file /boot/video.elf) | |
ustslave: Kernel Version: 24 | |
base_address 0x40000000 | |
seeking to 0 | |
seeking to e2dc0 | |
seeking to e2df8 | |
seeking to e2e30 | |
seeking to e8fe8 | |
seeking to e8ff4 | |
seeking to e9000 | |
seeking to 115710 | |
seeking to 117800 | |
Initializing embx... | |
Initializing AVS... | |
Initializing player 191... | |
Init of MME log wrapper | |
stm_v4l2_register_driver: driver 'stmvout' registered | |
stm_v4l2_register_driver: driver 'stmvbi' registered | |
snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw | |
pseudocard: 1 pseudo soundcard(s) found | |
pti loaded | |
no swts ->routing streams from dvr0 direct to the player | |
DVB: registering new adapter (STM Streamer) | |
0: DeviceContext 871e0088, DvbDemux 871e038c, DmxDevice 871e0574 | |
CaInit() | |
Initializing CI Controller | |
ptiInit context = 871e0088, demux = 871e038c | |
[TSM] init stream routing... | |
Bypass ci | |
TsinMode = Parallel *st-merger* | |
TsinMode = Parallel *st-merger* | |
TsinMode = Parallel *st-merger* | |
TsinMode = Parallel *st-merger* | |
pti ioremap 0xfe230000 -> 0xfe230000 | |
Load TC ... | |
loadtc: > | |
loadtc: < | |
Load TC done | |
PHY: 0:11 - Link is Up - 100/Full | |
i2c-stm: arbitration error | |
i2c-stm: arbitration error | |
DVB: registering adapter 0 frontend 3 (Dummy DVB-T)... | |
pI2c = 0x0 | |
pI2c = 0x87eb1818 | |
priv_mem->i2c_adap = 87eb1818 | |
Read error, Reg=[0xa3], Status=-121 | |
############nim_s3501_get_type temp = 0x87121e54, m_Value = 0x0 | |
Read error, Reg=[0xc0], Status=-121 | |
Read error, Reg=[0xa4], Status=-121 | |
spark_dvb_attach_s: error attaching d3501 | |
DVB: registering adapter 0 frontend 0 (Dummy DVB-S)... | |
session 2, demux 871e038c | |
Descrambler Handler = 1 | |
1: DeviceContext 871e0610, DvbDemux 871e0914, DmxDevice 871e0afc | |
CaInit() | |
ptiInit context = 871e0610, demux = 871e0914 | |
session 1, demux 871e0914 | |
Descrambler Handler = 1 | |
2: DeviceContext 871e0b98, DvbDemux 871e0e9c, DmxDevice 871e1084 | |
CaInit() | |
ptiInit context = 871e0b98, demux = 871e0e9c | |
session 0, demux 871e0e9c | |
Descrambler Handler = 1 | |
3: DeviceContext 871e1120, DvbDemux 871e1424, DmxDevice 871e160c | |
ptiInit context = 871e1120, demux = 871e1424 | |
session 3, demux 871e1424 | |
Descrambler Handler = 1 | |
stm_v4l2_register_driver: driver 'Linux DVB Overlay' registered | |
Player:DisplayInit: Pipeline 0 Device c1176420, Name = STi7105-main, Preferred video plane = 2 | |
Player:DisplayInit: Pipeline 1 Device c1176420, Name = STi7105-aux, Preferred video plane = 4 | |
SetPolicy - 00000000 00000000 PolicyPlayoutAlwaysPlayout 0 | |
SetPolicy - 00000000 00000000 PolicyPlayoutAlwaysDiscard 1 | |
SetPolicy - 00000000 00000000 PolicyMasterClock 0 | |
SetPolicy - 00000000 00000000 PolicyManifestFirstFrameEarly 1 | |
SetPolicy - 00000000 00000000 PolicyExternalTimeMapping 0 | |
SetPolicy - 00000000 00000000 PolicyExternalTimeMappingVsyncLocked 0 | |
SetPolicy - 00000000 00000000 PolicyAVDSynchronization 1 | |
SetPolicy - 00000000 00000000 PolicyClampPlaybackIntervalOnPlaybackDirectionChange 1 | |
SetPolicy - 00000000 00000000 PolicyTrickModeDomain 0 | |
SetPolicy - 00000000 00000000 PolicyStatisticsOnAudio 0 | |
SetPolicy - 00000000 00000000 PolicyStatisticsOnVideo 0 | |
SetPolicy - 00000000 00000000 PolicyDiscardLateFrames 2 | |
SetPolicy - 00000000 00000000 PolicyVideoStartImmediate 1 | |
SetPolicy - 00000000 00000000 PolicySyncStartImmediate 0 | |
SetPolicy - 00000000 00000000 PolicyRebaseOnFailureToDeliverDataInTime 1 | |
SetPolicy - 00000000 00000000 PolicyRebaseOnFailureToDecodeInTime 1 | |
SetPolicy - 00000000 00000000 PolicyH264AllowNonIDRResynchronization 1 | |
SetPolicy - 00000000 00000000 PolicyH264AllowBadPreProcessedFrames 1 | |
SetPolicy - 00000000 00000000 PolicyH264TreatDuplicateDpbValuesAsNonReferenceFrameFirst 1 | |
SetPolicy - 00000000 00000000 PolicyH264ForcePicOrderCntIgnoreDpbDisplayFrameOrdering 0 | |
SetPolicy - 00000000 00000000 PolicyH264TreatTopBottomPictureStructAsInterlaced 1 | |
SetPolicy - 00000000 00000000 PolicyMPEG2ApplicationType 2 | |
SetPolicy - 00000000 00000000 PolicyMPEG2DoNotHonourProgressiveFrameFlag 0 | |
SetPolicy - 00000000 00000000 PolicyClockPullingLimit2ToTheNPartsPerMillion 8 | |
SetPolicy - 00000000 00000000 PolicyLimitInputInjectAhead 0 | |
SetPolicy - 00000000 00000000 PolicyDecimateDecoderOutput 0 | |
SetPolicy - 00000000 00000000 PolicySymmetricJumpDetection 0 | |
SetPolicy - 00000000 00000000 PolicyPtsForwardJumpDetectionThreshold 4 | |
SetPolicy - 00000000 00000000 PolicyPixelAspectRatioCorrection 100 | |
SetPolicy - 00000000 00000000 PolicyAllowFrameDiscardAtNormalSpeed 0 | |
SetPolicy - 00000000 00000000 PolicyOperateCollator2InReversibleMode 0 | |
SetPolicy - 00000000 00000000 PolicyVideoOutputWindowResizeSteps 1 | |
SetPolicy - 00000000 00000000 PolicyIgnoreStreamUnPlayableCalls 0 | |
SetPolicy - 00000000 00000000 PolicyUsePTSDeducedDefaultFrameRates 1 | |
SetPolicy - 00000000 00000000 PolicyDiscardLateFrames 2 | |
SetPolicy - 00000000 00000000 PolicyVideoStartImmediate 1 | |
SetPolicy - 00000000 00000000 PolicyMPEG2DoNotHonourProgressiveFrameFlag 1 | |
Player:Mixer0AudioFactory: Performing JIT mixer0 (main room) instanciation. | |
OSDEV_LinkDevice - /dev/allocator, Major 245, Minor 0 | |
AllocatorLoadModule : Allocator device loaded | |
Switching Preprocessor clock to full speed. | |
OSDEV_LinkDevice - /dev/h264pp, Major 246, Minor 0 | |
H264ppLoadModule : H264pp device loaded | |
[CEC] init - starting | |
[CEC] allocating and registering button device | |
input: TDT RC event driver as /devices/virtual/input/input0 | |
mknod: /dev/dvb/adapter0/frontend1: File exists | |
INIT: Entering runlevel: 3 | |
Mount /dev in tmpfs | |
Copying device nodes to /dev | |
Mounting local filesystems... | |
kjournald starting. Commit interval 5 seconds | |
EXT3 FS on sda3, internal journal | |
EXT3-fs: recovery complete. | |
EXT3-fs: mounted filesystem with writeback data mode. | |
Unable to find swap-space signature | |
Cleaning /tmp. | |
Hostname: NextVOD. | |
Starting DHCP client: udhcpcudhcpc (v1.22.1) started | |
Sending discover... | |
Sending select for 192.168.0.14... | |
Lease of 192.168.0.14 obtained, lease time 86400 | |
route: SIOCDELRT: No such process | |
adding dns 192.168.0.1 | |
. | |
Starting lirc daemon: lircd. | |
lircd-0.9.0[745]: lircd(default) ready, using /var/run/lirc/lircd | |
Starting irexec daemon: irexeclircd-0.9.0[745]: accepted new client on /var/run/lirc/lircd | |
. | |
Starting NTP daemon: ntpd. | |
Starting telnet daemon: telnetd. | |
Starting FTP server: vsftpd. | |
Starting dbus daemon: dbus-daemon. | |
Starting the Avahi Daemon...Process 788 died: No such process; trying to remove PID file. (/var/run/avahi-daemon//pid) | |
done. | |
Starting the Avahi mDNS/DNS-SD Configuration Daemon...Process 791 died: No such process; trying to remove PID file. (/var/run//avahi-dnsconfd.pid) | |
done. | |
Detecting XBMC profile setting folder... | |
rm: can't remove '/.xbmc': No such file or directory | |
Creating symbolic link /.xbmc -> /media/hdd/.xbmc | |
Starting XBMClircd-0.9.0[745]: accepted new client on /var/run/lirc/lircd | |
commandline read: xbmc.bin | |
~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.12 |~~~~~~~~~~~~~~~~~~~~~~~~~~ | |
(c) 2001-2010 The world wide DirectFB Open Source Community | |
(c) 2000-2004 Convergence (integrated media) GmbH | |
---------------------------------------------------------------- | |
(*) DirectFB/Core: Single Application Core. (2015-02-09 07:24) | |
(*) DirectFB/STMfbdev: Found 'STi7105-main' (ID 102) with frame buffer at 0x48390000, 24576k (MMIO 0xfe20b000, 4k) | |
(*) Direct/Thread: Started 'Linux Input' (-1) [INPUT OTHER/OTHER 0/0] <8388608>... | |
(*) DirectFB/Input: TDT RC event driver 0.1 (directfb.org) | |
(*) DirectFB/Genefx: No software fallbacks supported | |
(*) DirectFB/stgfx2: stdev/stdrv: 0x10ba2c0 / 0x10b9f38 | |
(*) DirectFB/stgfx2: running in stmfbdev | |
(*) BDisp/BLT: shared area phys/size: 0x48331000/188416 | |
(*) BDisp/BLT: blitter is a 'STi7200c2/7111/7141/7105' (6) | |
(*) BDisp/BLT: nodes area phys/size: 0x48332000/184320 (184320 usable -> 768 noproc_video_videomode_choices_read 254 | |
des) -> ends @ 0proc_video_videomode_choices_read 20 | |
x4835f000 | |
(*) BDisp/BLT: shared area/nodes mmap()ed to proc_video_videomode_read | |
0x29575000 / 0x2Found mode to set 1080p60 at 9 | |
c73e000 | |
(*) BDiproc_video_videomode_read | |
sp/BLT: reservedFound mode to set 1080p60 at 9 | |
12397 bytes for CLUT & filters @ 0x48390000 + 0x017fcf00 = 0x49b8cf00 | |
proc_video_videomode_write 7 - (*) DirectFB/stg1080i50 | |
fx2: CLUT mmap()Found mode to set 1080i50 at 19 | |
ed to 0x2bf03700detected fb_set_par error, error code: -16 | |
(*) DirectFB/serror setting new resolution -16 | |
tgfx2: CLUT mmap()ed to 0x2bf02700 | |
(*) DirectFB/stgfx2: CLUT mmap()ed to 0x2bf02b00 | |
(*) DirectFB/stgfx2: CLUT mmap()ed to 0x2bf02f00 | |
(*) DirectFB/stgfx2: CLUT mmap()ed to 0x2bf03300 | |
(*) BDisp/Surfaces: using 24563kB of video memory (12544 bytes reserved)! | |
(*) BDisp/Surfaces: found auxmem @ 4a000000 (12288kB)! | |
(*) BDisp/Surfaces: 12288kB of auxmem! | |
(*) DirectFB/Graphics: ST Microelectronics BDispII w/ user space AQs 0.9 (ST Microelectronics) | |
(*) DirectFB/Core/WM: Default 0.3 (directfb.org) | |
proc_video_alpha_write 3 - 255 | |
proc_video_videomode_read | |
Found mode to set 1080p60 at 9 | |
proc_video_videomode_read | |
Found mode to set 1080p60 at 9 | |
login[814]: root login on 'pts/0' | |
Adding 232900k swap on /dev/sda5. Priority:-1 extents:1 across:232900k | |
login[846]: root login on 'pts/0' | |
INIT: Switching to runlevel: 0 | |
INIT: Sending processes the TERM signal | |
(!) [ 778: 0.000] --> Caught signal 15 (sent by pid 1, uid 0) <-- | |
(!!!) *** WARNING [still objects in 'Layer Region Pool'] *** [object.c:241 in fusion_object_pool_destroy()] | |
(!!!) *** WARNING [still objects in 'Layer Context Pool'] *** [object.c:241 in fusion_object_pool_destroy()] | |
(!) STMfbdev/Screen: Could not restore output config | |
--> Invalid argument | |
(!!!) *** WARNING [still objects in 'Surface Pool'] *** [object.c:241 in fusion_object_pool_destroy()] | |
(*) DirectFB/stgfx2: 250455 starts, 241988 (1516/241730) interrupts, 1671 wait_idle, 0 wait_next, 241730 idle | |
(*) DirectFB/stgfx2: 291163 ops, 1 ops/start, 1 ops/idle, 1 starts/idle | |
lircd-0.9.0[745]: removed client | |
Sending all processes the TERM signal...done. | |
lircd-0.9.0[745]: caught signal | |
Sending all processes the KILL signal...done. | |
Deactivating swap...umount: tmpfs busy - remounted read-only | |
done. | |
Unmounting local filesystems...umount: tmpfs busy - remounted read-only | |
umount: can't umount /dev/pts: Invalid argument | |
umount: devtmpfs busy - remounted read-only | |
done. | |
/bin/fp_control: SW Version 1.04 | |
Model: spark7162 | |
vBoxType: 11 | |
Selected Model: Edision Spark frontpanel control utility | |
Spark_init | |
cannot open /dev/vfd | |
No such file or directory | |
checkConfig | |
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S | |
, WAKEUPDECREMENT 300 | |
setled: : Bad file descriptor | |
/bin/fp_control: SW Version 1.04 | |
Model: spark7162 | |
vBoxType: 11 | |
Selected Model: Edision Spark frontpanel control utility | |
Spark_init | |
cannot open /dev/vfd | |
No such file or directory | |
checkConfig | |
configs: proc_progress_write 2 - DISPLAY = 1, DIS0 | |
PLAYCUSTOM = 1, CUSTOM = %H:%M:%S | |
, WAKEUPDECREMENT 300 | |
setled: : Bad file descriptor | |
/bin/fp_control: SW Version 1.04 | |
Model: spark7162 | |
vBoxType: 11 | |
Selected Model: Edision Spark frontpanel control utility | |
Spark_init | |
cannot open /dev/vfd | |
No such file or directory | |
checkConfig | |
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S | |
, WAKEUPDECREMENT 300 | |
Setting Clock to current time: 21:20:54 04-07-2015 | |
settime: : Bad file descriptor | |
/bin/fp_control: SW Version 1.04 | |
Model: spark7162 | |
vBoxType: 11 | |
Selected Model: Edision Spark frontpanel control utility | |
Spark_init | |
cannot open /dev/vfd | |
No such file or directory | |
checkConfig | |
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S | |
, WAKEUPDECREMENT 300 | |
Current Time: 21:20:54 04-07-2015 | |
Getting enigma2 wakeup time - Done | |
Getting neutrino wakeup time - Error reading /var/tuxbox/config/timerd.conf | |
no e2 timer found clearing fp wakeup time ... good bye ... | |
standby: : Bad file descriptor | |
halt: invalid number '-f' | |
INIT: no more processes left in this runlevel | |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment