Created
October 25, 2013 16:08
-
-
Save fuyuanli/7157194 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.10.25 23:56:35 =~=~=~=~=~=~=~=~=~=~=~= | |
| Board: STx7105-PDK [32-bit mode] | |
| U-Boot 1.3.1 (Oct 6 2013 - 04:36:18) - stm23_0045 | |
| DRAM: 256 MiB | |
| SPI: ST M25P80 (1MiB) device (page=256,erase=4096) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| UBOOTWPDA version: 8365896 | |
| swUpdate.c:1024 RESET pressed, 'Red' LED trying external USB at first | |
| (Re)start USB... | |
| USB: scanning bus for devices... 2 USB Device(s) found | |
| scanning bus for storage devices... 1 Storage Device(s) found | |
| Failed to mount ext2 filesystem... | |
| reading uboot.sh | |
| ** Unable to read "uboot.sh" from usb 0:1 ** | |
| Failed to mount ext2 filesystem... | |
| reading iptvubootupdate.bin | |
| ................................................... | |
| 524360 bytes read | |
| swUpdate.c:772 UBOOT_Ver: File:8365896 Flash:8365896 | |
| swUpdate.c:980 skip upgrade same version iptvubootupdate.bin | |
| 843 bytes read | |
| load_uboot_env.c:31 = uboot.sh content= | |
| =# UBOOTWPDA config http://www.twpda.com/2013/08/uboot-code.html | |
| # NOTE: This file's length should under 988 bytes | |
| # bootargs(old): root=8:1 means sda1, sda2 8:2, sdb1 8:17, sdb2 8:18 | |
| # bootargs(new): root=/dev/sda2 | |
| # bootcmd: 0:1 first part, 0:2 2nd part | |
| # usbcfg: 0:internal, 1:external | |
| # boot settings for sh4twbox install disk | |
| # * bootargs: root=8:1 means sda1, sda2 8:2, sdb1 8:17, sdb2 8:18 | |
| # * bootcmd: 0:1 first usb parition, 0:2 2nd usb parition | |
| setenv bootargs 'console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:10:08:E2:12:06:BD phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048' | |
| #setenv bootcmd 'usbcfg 0; usb start; usb info; usb part; ext2load usb 0:1 80000000 vmlinux.ub; bootm 80000000' | |
| setenv bootcmd 'fatload usb 0:1 80000000 vmlinux.ub; bootm 80000000' | |
| = end of uboot.sh = | |
| Hit any key to stop autoboot: 0 | |
| reading vmlinux.ub | |
| ...................................................................................................................................................................................................................................................................................................... | |
| 3020623 bytes read | |
| ## Booting image at 80000000 ... | |
| Image Name: Linux-2.6.32.59-7641-PDK7105-32B | |
| Image Type: SuperH Linux Kernel Image (gzip compressed) | |
| Data Size: 3020559 Bytes = 2.9 MiB | |
| Load Address: 80800000 | |
| Entry Point: 80801000 | |
| Verifying Checksum ... OK | |
| Uncompressing Kernel Image ... OK | |
| CMDLen=186 | |
| There is "hwaddr" keywords! Position=112 | |
| Read MacAddr=24cf21b4f697 | |
| [iptv_kernel]:Starting kernel console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:f6:97 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 - 0x00000000 - 0 ... | |
| Linux version 2.6.32.59-7641-PDK7105-32BITS (dlin@u40) (gcc version 4.7.3 20130514 (STMicroelectronics/Linux Base 4.7.3-124) (GCC) ) #4 PREEMPT Thu Oct 24 15:10:15 CST 2013 | |
| Boot params: | |
| ... MOUNT_ROOT_RDONLY - 00000001 | |
| ... RAMDISK_FLAGS - 00000000 | |
| ... ORIG_ROOT_DEV - 00000200 | |
| ... LOADER_TYPE - 00000000 | |
| ... INITRD_START - 00000000 | |
| ... INITRD_SIZE - 00000000 | |
| Booting machvec: pdk7105 | |
| Node 0: start_pfn = 0x40000, low = 0x50000 | |
| Zone PFN ranges: | |
| Normal 0x00040000 -> 0x00050000 | |
| Movable zone start PFN for each node | |
| early_node_map[1] active PFN ranges | |
| 0: 0x00040000 -> 0x00050000 | |
| STMicroelectronics PDK7105-SDK board initialisation | |
| STx7105 version 3.x | |
| Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 | |
| Kernel command line: console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:f6:97 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 | |
| bpa2: partition 'bigphysarea' created at 0x40f2b000, size 8192 kB (0x00800000 B) | |
| PID hash table entries: 1024 (order: 0, 4096 bytes) | |
| Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
| PVR=04909200 CVR=60880000 PRR=00009e20 | |
| I-cache : n_ways=2 n_sets=512 way_incr=16384 | |
| I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
| D-cache : n_ways=2 n_sets=512 way_incr=16384 | |
| D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
| Memory: 238080k/262144k available (3610k kernel code, 1349k data, 148k init) | |
| Hierarchical RCU implementation. | |
| NR_IRQS:600 | |
| Failed to enable clk CLKA_REF, ignoring | |
| Failed to enable clk CLKA_PLL0LS, ignoring | |
| Console: colour dummy device 80x25 | |
| console [ttyAS0] enabled | |
| sh_tmu: TMU0 used for clock events | |
| sh_tmu: TMU0 used for periodic clock events | |
| sh_tmu: TMU1 used as clock source | |
| Calibrating delay loop... 448.51 BogoMIPS (lpj=897024) | |
| Mount-cache hash table entries: 512 | |
| CPU: STx7105 | |
| [STM][PM-Sys]: ilc3 @ 4096 | |
| NET: Registered protocol family 16 | |
| Configuring FLASH for boot-from-spi: boot_mode=2 | |
| bio: create slab <bio-0> at 0 | |
| SCSI subsystem initialized | |
| usbcore: registered new interface driver usbfs | |
| usbcore: registered new interface driver hub | |
| usbcore: registered new device driver usb | |
| DMA: Registering DMA API. | |
| Switching to clocksource TMU1 | |
| sh_tmu: TMU0 used for oneshot clock events | |
| Switched to NOHz mode on CPU #0 | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
| TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| TCP: Hash tables configured (established 8192 bind 8192) | |
| TCP reno registered | |
| NET: Registered protocol family 1 | |
| RPC: Registered udp transport module. | |
| RPC: Registered tcp transport module. | |
| RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| sq: Registering store queue API. | |
| [STM]: [CPUFreq] Registered | |
| [STM]: [PM]: Suspend support registered | |
| Slow work thread pool: Starting up | |
| Slow work thread pool: Ready | |
| NTFS driver 2.1.29 [Flags: R/O]. | |
| JFFS2 version 2.2. (NAND) 穢 2001-2006 Red Hat, Inc. | |
| ROMFS MTD (C) 2007 Red Hat, Inc. | |
| fuse init (API version 7.13) | |
| msgmni has been set to 465 | |
| alg: No test for stdrng (krng) | |
| io scheduler noop registered | |
| io scheduler anticipatory registered | |
| io scheduler deadline registered | |
| io scheduler cfq registered (default) | |
| lirc_dev: IR Remote Control driver registered, major 61 | |
| lirc-stm: probe found data for platform device lirc-stm | |
| lirc-stm: STM LIRC plugin using IRQ 125 in IR mode | |
| lirc_dev: lirc_register_driver: sample_rate: 0 | |
| STMicroelectronics LIRC driver initialized. | |
| STMicroelectronics ASC driver initialized | |
| stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc | |
| Uniform Multi-Platform E-IDE driver | |
| ide-gd driver 1.18 | |
| MiPHY driver style MiPHY3-65 probed successfully | |
| MiPHY3-65, c1.5 Claimed by sata-stm | |
| scsi0 : sata-stm | |
| ata1: SATA max UDMA/133 irq 72 | |
| ata1: SATA link down (SStatus 0 SControl 0) | |
| physmap platform flash device: 00000000 at 00000000 | |
| physmap-flash physmap-flash.0: Could not reserve memory region | |
| physmap-flash: probe of physmap-flash.0 failed with error -12 | |
| stmmac - user ID: 0x10, Synopsys ID: 0x33 | |
| No HW DMA feature register supported | |
| Enhanced/Alternate descriptors | |
| RX Checksum Offload Engine supported | |
| TX Checksum insertion supported | |
| Wake-Up On Lan supported | |
| nwhw_config: (eth0) setting mac address: 24:cf:21:b4:f6:97 | |
| usbmon: debugfs is not available | |
| ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| stm_usb_probe: usb_phy_clk clock not found for stm-usb.0 | |
| stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller | |
| stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1 | |
| stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00 | |
| stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00 | |
| usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
| usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb1: Product: STMicroelectronics EHCI Host Controller | |
| usb usb1: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ehci_hcd | |
| usb usb1: SerialNumber: stm-ehci.0 | |
| usb usb1: configuration #1 chosen from 1 choice | |
| hub 1-0:1.0: USB hub found | |
| hub 1-0:1.0: 1 port detected | |
| stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller | |
| stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2 | |
| stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00 | |
| usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 | |
| usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb2: Product: STMicroelectronics OHCI Host Controller | |
| usb usb2: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ohci_hcd | |
| usb usb2: SerialNumber: stm-ohci.0 | |
| usb usb2: configuration #1 chosen from 1 choice | |
| hub 2-0:1.0: USB hub found | |
| hub 2-0:1.0: 1 port detected | |
| Initializing USB Mass Storage driver... | |
| usbcore: registered new interface driver usb-storage | |
| USB Mass Storage support registered. | |
| i2c /dev entries driver | |
| cpuidle: using governor ladder | |
| cpuidle: using governor menu | |
| sh_tmu: TMU0 kept as earlytimer | |
| sh_tmu: TMU1 kept as earlytimer | |
| usbcore: registered new interface driver usbhid | |
| usbhid: v2.6:USB HID core driver | |
| [STM][PM-Sys]: emi @ 40 | |
| [STM][PM-Sys]: gpio @ 20 | |
| STMicroelectronics - Coprocessors st231 Init | |
| st-coprocessor-0: No RAM reserved | |
| st231.0 Coprocessor ------------------------------------------- | |
| not configured! | |
| --------------------------------------------------------------- | |
| st-coprocessor-1: No RAM reserved | |
| st231.1 Coprocessor ------------------------------------------- | |
| not configured! | |
| --------------------------------------------------------------- | |
| DMA: Registering fdma_dmac.0 handler (16 channels). | |
| IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs | |
| DMA: Registering fdma_dmac.1 handler (16 channels). | |
| IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs | |
| stm-rng hardware driver 1.0 configured | |
| stm-rtc stm-rtc: rtc core: registered stm-rtc as rtc0 | |
| ip_tables: (C) 2000-2006 Netfilter Core Team | |
| TCP cubic registered | |
| NET: Registered protocol family 17 | |
| stm-rtc stm-rtc: setting system clock to 2014-04-23 19:27:44 UTC (1398281264) | |
| usb 1-1: new high speed USB device using stm-ehci and address 2 | |
| usb 1-1: New USB device found, idVendor=090c, idProduct=1000 | |
| usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| usb 1-1: Product: USB Flash Disk | |
| usb 1-1: Manufacturer: General | |
| usb 1-1: SerialNumber: TT00000000040256 | |
| usb 1-1: configuration #1 chosen from 1 choice | |
| scsi1 : SCSI emulation for USB Mass Storage devices | |
| stm_usb_probe: usb_phy_clk clock not found for stm-usb.1 | |
| stm-ehci stm-ehci.1: STMicroelectronics EHCI Host Controller | |
| stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3 | |
| stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00 | |
| stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00 | |
| usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 | |
| usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb3: Product: STMicroelectronics EHCI Host Controller | |
| usb usb3: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ehci_hcd | |
| usb usb3: SerialNumber: stm-ehci.1 | |
| usb usb3: configuration #1 chosen from 1 choice | |
| hub 3-0:1.0: USB hub found | |
| hub 3-0:1.0: 1 port detected | |
| stm-ohci stm-ohci.1: STMicroelectronics OHCI Host Controller | |
| stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4 | |
| stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00 | |
| usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 | |
| usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb4: Product: STMicroelectronics OHCI Host Controller | |
| usb usb4: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ohci_hcd | |
| usb usb4: SerialNumber: stm-ohci.1 | |
| usb usb4: configuration #1 chosen from 1 choice | |
| hub 4-0:1.0: USB hub found | |
| hub 4-0:1.0: 1 port detected | |
| usb 3-1: new high speed USB device using stm-ehci and address 2 | |
| usb 3-1: New USB device found, idVendor=0781, idProduct=5571 | |
| usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| usb 3-1: Product: Cruzer Fit | |
| usb 3-1: Manufacturer: SanDisk | |
| usb 3-1: SerialNumber: 4C532000060317113330 | |
| usb 3-1: configuration #1 chosen from 1 choice | |
| scsi2 : SCSI emulation for USB Mass Storage devices | |
| scsi 2:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 5 | |
| scsi 1:0:0:0: Direct-Access General USB Flash Disk 1100 PQ: 0 ANSI: 0 CCS | |
| sd 2:0:0:0: Attached scsi generic sg0 type 0 | |
| sd 2:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB) | |
| sd 1:0:0:0: [sdb] 15679488 512-byte logical blocks: (8.02 GB/7.47 GiB) | |
| sd 1:0:0:0: Attached scsi generic sg1 type 0 | |
| sd 2:0:0:0: [sda] Write Protect is off | |
| sd 2:0:0:0: [sda] Assuming drive cache: write through | |
| sd 1:0:0:0: [sdb] Write Protect is off | |
| sd 1:0:0:0: [sdb] Assuming drive cache: write through | |
| sd 2:0:0:0: [sda] Assuming drive cache: write through | |
| sda: | |
| sda1 sda2 | |
| sd 1:0:0:0: [sdb] Assuming drive cache: write through | |
| sdb: | |
| sdb1 sdb2 | |
| sd 2:0:0:0: [sda] Assuming drive cache: write through | |
| sd 2:0:0:0: [sda] Attached SCSI removable disk | |
| sd 1:0:0:0: [sdb] Assuming drive cache: write through | |
| sd 1:0:0:0: [sdb] Attached SCSI removable disk | |
| EXT3-fs: sdb2: couldn't mount because of unsupported optional features (240). | |
| List of all partitions: | |
| 0800 15633408 sda driver: sd | |
| 0801 16384 sda1 | |
| 0802 12288 sda2 | |
| 0810 7839744 sdb driver: sd | |
| 0811 38254 sdb1 | |
| 0812 7794826 sdb2 | |
| No filesystem could mount root, tried: ext3 | |
| Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,18) | |
| | |
| Board: STx7105-PDK [32-bit mode] | |
| U-Boot 1.3.1 (Oct 6 2013 - 04:36:18) - stm23_0045 | |
| DRAM: 256 MiB | |
| SPI: ST M25P80 (1MiB) device (page=256,erase=4096) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| UBOOTWPDA version: 8365896 | |
| swUpdate.c:1031 'Purple' LED, trying internal USB at first | |
| (Re)start USB... | |
| USB: scanning bus for devices... 2 USB Device(s) found | |
| scanning bus for storage devices... 1 Storage Device(s) found | |
| Failed to mount ext2 filesystem... | |
| reading uboot.sh | |
| 695 bytes read | |
| load_uboot_env.c:31 = uboot.sh content= | |
| =# UBOOTWPDA config http://www.twpda.com/2013/08/uboot-code.html | |
| # bootargs(old): root=8:1 means sda1, sda2 8:2, sdb1 8:17, sdb2 8:18 | |
| # bootargs(new): root=/dev/sda2 | |
| # bootcmd: 0:1 first part, 0:2 2nd part | |
| # usbcfg: 0:internal, 1:external | |
| # boot settings for internal USB sda1:kernel+uboot.sh sda2:ext4 | |
| setenv bootargs 'console=ttyAS0,115200 rootdelay=0 root=/dev/sda2 rootfstype=ext4 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:10:08:E2:12:06:BD phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048' | |
| setenv bootcmd 'usbcfg 0; usb start; usb info; usb part; fatload usb 0:1 80000000 vmlinux.ub; bootm 80000000' | |
| #setenv bootcmd 'ext2load usb 0:2 80000000 boot/vmlinux.ub; bootm 80000000' | |
| = end of uboot.sh = | |
| Hit any key to stop autoboot: 0 | |
| set usbcfg=USB_INT_REGS | |
| (Re)start USB... | |
| USB: scanning bus for devices... 2 USB Device(s) found | |
| scanning bus for storage devices... 1 Storage Device(s) found | |
| 1: Hub, USB Revision 1.10 | |
| - OHCI Root Hub | |
| - Class: Hub | |
| - PacketSize: 8 Configurations: 1 | |
| - Vendor: 0x0000 Product 0x0000 Version 0.0 | |
| Configuration: 1 | |
| - Interfaces: 1 Self Powered 0mA | |
| Interface: 0 | |
| - Alternate Setting 0, Endpoints: 1 | |
| - Class Hub | |
| - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms | |
| 2: Mass Storage, USB Revision 2.0 | |
| - General USB Flash Disk TT00000000009625 | |
| - Class: (from Interface) Mass Storage | |
| - PacketSize: 64 Configurations: 1 | |
| - Vendor: 0x090c Product 0x1000 Version 17.0 | |
| Configuration: 1 | |
| - Interfaces: 1 Bus Powered 500mA | |
| Interface: 0 | |
| - Alternate Setting 0, Endpoints: 2 | |
| - Class Mass Storage, Transp. SCSI, Bulk only | |
| - Endpoint 1 In Bulk MaxPacket 64 | |
| - Endpoint 2 Out Bulk MaxPacket 64 | |
| print_part of 0 | |
| Partition Map for USB device 0 -- Partition Type: DOS | |
| Partition Start Sector Num Sectors Type | |
| 1 62 76508 1 | |
| 2 76570 1558965283 | |
| print_part of 1 | |
| ## Unknown partition table | |
| print_part of 2 | |
| ## Unknown partition table | |
| print_part of 3 | |
| ## Unknown partition table | |
| print_part of 4 | |
| ## Unknown partition table | |
| reading vmlinux.ub | |
| ...................................................................................................................................................................................................................................................................................................... | |
| 3020581 bytes read | |
| ## Booting image at 80000000 ... | |
| Image Name: Linux-2.6.32.59-0167-PDK7105-32B | |
| Image Type: SuperH Linux Kernel Image (gzip compressed) | |
| Data Size: 3020517 Bytes = 2.9 MiB | |
| Load Address: 80800000 | |
| Entry Point: 80801000 | |
| Verifying Checksum ... OK | |
| Uncompressing Kernel Image ... OK | |
| CMDLen=186 | |
| There is "hwaddr" keywords! Position=112 | |
| Read MacAddr=24cf21b4a016 | |
| [iptv_kernel]:Starting kernel console=ttyAS0,115200 rootdelay=0 root=/dev/sda2 rootfstype=ext4 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:a0:16 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 - 0x00000000 - 0 ... | |
| Linux version 2.6.32.59-0167-PDK7105-32BITS (dlin@t64) (gcc version 4.7.3 20130514 (STMicroelectronics/Linux Base 4.7.3-124) (GCC) ) #2 PREEMPT Sat Oct 19 22:50:19 CST 2013 | |
| Boot params: | |
| ... MOUNT_ROOT_RDONLY - 00000001 | |
| ... RAMDISK_FLAGS - 00000000 | |
| ... ORIG_ROOT_DEV - 00000200 | |
| ... LOADER_TYPE - 00000000 | |
| ... INITRD_START - 00000000 | |
| ... INITRD_SIZE - 00000000 | |
| Booting machvec: pdk7105 | |
| Node 0: start_pfn = 0x40000, low = 0x50000 | |
| Zone PFN ranges: | |
| Normal 0x00040000 -> 0x00050000 | |
| Movable zone start PFN for each node | |
| early_node_map[1] active PFN ranges | |
| 0: 0x00040000 -> 0x00050000 | |
| STMicroelectronics PDK7105-SDK board initialisation | |
| STx7105 version 3.x | |
| Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 | |
| Kernel command line: console=ttyAS0,115200 rootdelay=0 root=/dev/sda2 rootfstype=ext4 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:a0:16 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 | |
| bpa2: partition 'bigphysarea' created at 0x40f2b000, size 8192 kB (0x00800000 B) | |
| PID hash table entries: 1024 (order: 0, 4096 bytes) | |
| Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
| PVR=04909200 CVR=60880000 PRR=00009e20 | |
| I-cache : n_ways=2 n_sets=512 way_incr=16384 | |
| I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
| D-cache : n_ways=2 n_sets=512 way_incr=16384 | |
| D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
| Memory: 238080k/262144k available (3610k kernel code, 1349k data, 148k init) | |
| Hierarchical RCU implementation. | |
| NR_IRQS:600 | |
| Failed to enable clk CLKA_REF, ignoring | |
| Failed to enable clk CLKA_PLL0LS, ignoring | |
| Console: colour dummy device 80x25 | |
| console [ttyAS0] enabled | |
| sh_tmu: TMU0 used for clock events | |
| sh_tmu: TMU0 used for periodic clock events | |
| sh_tmu: TMU1 used as clock source | |
| Calibrating delay loop... 448.51 BogoMIPS (lpj=897024) | |
| Mount-cache hash table entries: 512 | |
| CPU: STx7105 | |
| [STM][PM-Sys]: ilc3 @ 4096 | |
| NET: Registered protocol family 16 | |
| Configuring FLASH for boot-from-spi: boot_mode=2 | |
| bio: create slab <bio-0> at 0 | |
| SCSI subsystem initialized | |
| usbcore: registered new interface driver usbfs | |
| usbcore: registered new interface driver hub | |
| usbcore: registered new device driver usb | |
| DMA: Registering DMA API. | |
| Switching to clocksource TMU1 | |
| sh_tmu: TMU0 used for oneshot clock events | |
| Switched to NOHz mode on CPU #0 | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
| TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| TCP: Hash tables configured (established 8192 bind 8192) | |
| TCP reno registered | |
| NET: Registered protocol family 1 | |
| RPC: Registered udp transport module. | |
| RPC: Registered tcp transport module. | |
| RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| sq: Registering store queue API. | |
| [STM]: [CPUFreq] Registered | |
| [STM]: [PM]: Suspend support registered | |
| Slow work thread pool: Starting up | |
| Slow work thread pool: Ready | |
| NTFS driver 2.1.29 [Flags: R/O]. | |
| JFFS2 version 2.2. (NAND) 穢 2001-2006 Red Hat, Inc. | |
| ROMFS MTD (C) 2007 Red Hat, Inc. | |
| fuse init (API version 7.13) | |
| msgmni has been set to 465 | |
| alg: No test for stdrng (krng) | |
| io scheduler noop registered | |
| io scheduler anticipatory registered | |
| io scheduler deadline registered | |
| io scheduler cfq registered (default) | |
| lirc_dev: IR Remote Control driver registered, major 61 | |
| lirc-stm: probe found data for platform device lirc-stm | |
| lirc-stm: STM LIRC plugin using IRQ 125 in IR mode | |
| lirc_dev: lirc_register_driver: sample_rate: 0 | |
| STMicroelectronics LIRC driver initialized. | |
| STMicroelectronics ASC driver initialized | |
| stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc | |
| Uniform Multi-Platform E-IDE driver | |
| ide-gd driver 1.18 | |
| MiPHY driver style MiPHY3-65 probed successfully | |
| MiPHY3-65, c1.5 Claimed by sata-stm | |
| scsi0 : sata-stm | |
| ata1: SATA max UDMA/133 irq 72 | |
| ata1: SATA link down (SStatus 0 SControl 0) | |
| physmap platform flash device: 00000000 at 00000000 | |
| physmap-flash physmap-flash.0: Could not reserve memory region | |
| physmap-flash: probe of physmap-flash.0 failed with error -12 | |
| stmmac - user ID: 0x10, Synopsys ID: 0x33 | |
| No HW DMA feature register supported | |
| Enhanced/Alternate descriptors | |
| RX Checksum Offload Engine supported | |
| TX Checksum insertion supported | |
| Wake-Up On Lan supported | |
| nwhw_config: (eth0) setting mac address: 24:cf:21:b4:a0:16 | |
| usbmon: debugfs is not available | |
| ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| stm_usb_probe: usb_phy_clk clock not found for stm-usb.0 | |
| stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller | |
| stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1 | |
| stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00 | |
| stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00 | |
| usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
| usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb1: Product: STMicroelectronics EHCI Host Controller | |
| usb usb1: Manufacturer: Linux 2.6.32.59-0167-PDK7105-32BITS ehci_hcd | |
| usb usb1: SerialNumber: stm-ehci.0 | |
| usb usb1: configuration #1 chosen from 1 choice | |
| hub 1-0:1.0: USB hub found | |
| hub 1-0:1.0: 1 port detected | |
| stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller | |
| stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2 | |
| stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00 | |
| usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 | |
| usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb2: Product: STMicroelectronics OHCI Host Controller | |
| usb usb2: Manufacturer: Linux 2.6.32.59-0167-PDK7105-32BITS ohci_hcd | |
| usb usb2: SerialNumber: stm-ohci.0 | |
| usb usb2: configuration #1 chosen from 1 choice | |
| hub 2-0:1.0: USB hub found | |
| hub 2-0:1.0: 1 port detected | |
| Initializing USB Mass Storage driver... | |
| usbcore: registered new interface driver usb-storage | |
| USB Mass Storage support registered. | |
| i2c /dev entries driver | |
| cpuidle: using governor ladder | |
| cpuidle: using governor menu | |
| sh_tmu: TMU0 kept as earlytimer | |
| sh_tmu: TMU1 kept as earlytimer | |
| usbcore: registered new interface driver usbhid | |
| usbhid: v2.6:USB HID core driver | |
| [STM][PM-Sys]: emi @ 40 | |
| [STM][PM-Sys]: gpio @ 20 | |
| STMicroelectronics - Coprocessors st231 Init | |
| st-coprocessor-0: No RAM reserved | |
| st231.0 Coprocessor ------------------------------------------- | |
| not configured! | |
| --------------------------------------------------------------- | |
| st-coprocessor-1: No RAM reserved | |
| st231.1 Coprocessor ------------------------------------------- | |
| not configured! | |
| --------------------------------------------------------------- | |
| DMA: Registering fdma_dmac.0 handler (16 channels). | |
| IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs | |
| DMA: Registering fdma_dmac.1 handler (16 channels). | |
| IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs | |
| stm-rng hardware driver 1.0 configured | |
| stm-rtc stm-rtc: rtc core: registered stm-rtc as rtc0 | |
| ip_tables: (C) 2000-2006 Netfilter Core Team | |
| TCP cubic registered | |
| NET: Registered protocol family 17 | |
| stm-rtc stm-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) | |
| usb 1-1: new high speed USB device using stm-ehci and address 2 | |
| usb 1-1: New USB device found, idVendor=090c, idProduct=1000 | |
| usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| usb 1-1: Product: USB Flash Disk | |
| usb 1-1: Manufacturer: General | |
| usb 1-1: SerialNumber: TT00000000009625 | |
| usb 1-1: configuration #1 chosen from 1 choice | |
| scsi1 : SCSI emulation for USB Mass Storage devices | |
| stm_usb_probe: usb_phy_clk clock not found for stm-usb.1 | |
| stm-ehci stm-ehci.1: STMicroelectronics EHCI Host Controller | |
| stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3 | |
| stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00 | |
| stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00 | |
| usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 | |
| usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb3: Product: STMicroelectronics EHCI Host Controller | |
| usb usb3: Manufacturer: Linux 2.6.32.59-0167-PDK7105-32BITS ehci_hcd | |
| usb usb3: SerialNumber: stm-ehci.1 | |
| usb usb3: configuration #1 chosen from 1 choice | |
| hub 3-0:1.0: USB hub found | |
| hub 3-0:1.0: 1 port detected | |
| stm-ohci stm-ohci.1: STMicroelectronics OHCI Host Controller | |
| stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4 | |
| stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00 | |
| usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 | |
| usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb4: Product: STMicroelectronics OHCI Host Controller | |
| usb usb4: Manufacturer: Linux 2.6.32.59-0167-PDK7105-32BITS ohci_hcd | |
| usb usb4: SerialNumber: stm-ohci.1 | |
| usb usb4: configuration #1 chosen from 1 choice | |
| hub 4-0:1.0: USB hub found | |
| hub 4-0:1.0: 1 port detected | |
| usb 3-1: new high speed USB device using stm-ehci and address 2 | |
| usb 3-1: New USB device found, idVendor=0781, idProduct=5571 | |
| usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| usb 3-1: Product: Cruzer Fit | |
| usb 3-1: Manufacturer: SanDisk | |
| usb 3-1: SerialNumber: 4C532000060317113330 | |
| usb 3-1: configuration #1 chosen from 1 choice | |
| scsi2 : SCSI emulation for USB Mass Storage devices | |
| scsi 1:0:0:0: Direct-Access General USB Flash Disk 1100 PQ: 0 ANSI: 0 CCS | |
| sd 1:0:0:0: Attached scsi generic sg0 type 0 | |
| sd 1:0:0:0: [sda] 15679488 512-byte logical blocks: (8.02 GB/7.47 GiB) | |
| 1a | |
| 00 | |
| 3f | |
| 00 | |
| scsi 2:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 5 | |
| c0 00 | |
| sd 1:0:0:0: [sda] Write Protect is off | |
| sd 1:0:0:0: [sda] Assuming drive cache: write through | |
| sd 2:0:0:0: Attached scsi generic sg1 type 0 | |
| sd 2:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB) | |
| sd 1:0:0:0: [sda] Assuming drive cache: write through | |
| sda: | |
| sd 2:0:0:0: [sdb] Write Protect is off | |
| sd 2:0:0:0: [sdb] Assuming drive cache: write through | |
| sda1 sda2 | |
| 1e | |
| 00 | |
| 00 00 01 00 | |
| sd 1:0:0:0: [sda] Assuming drive cache: write through | |
| sd 1:0:0:0: [sda] Attached SCSI removable disk | |
| sd 2:0:0:0: [sdb] Assuming drive cache: write through | |
| sdb: | |
| sdb1 sdb2 | |
| sd 2:0:0:0: [sdb] Assuming drive cache: write through | |
| sd 2:0:0:0: [sdb] Attached SCSI removable disk | |
| EXT4-fs (sda2): Ignoring delalloc option - requested data journaling mode | |
| EXT4-fs (sda2): 1 truncate cleaned up | |
| EXT4-fs (sda2): recovery complete | |
| EXT4-fs (sda2): mounted filesystem with journalled data mode | |
| VFS: Mounted root (ext4 filesystem) on device 8:2. | |
| Freeing unused kernel memory: 148k freed | |
| INIT: version 2.88 booting | |
| [info] Using makefile-style concurrent boot in runlevel S. | |
| [....] Starting the hotplug events dispatcher: udevd[ ok . | |
| [....] Synthesizing the initial hotplug events...[ ok done. | |
| 00 00 00 01 58 00 00 08 00 | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| 00 | |
| 00 | |
| 00 | |
| 03 98 00 00 08 00 | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| [....] Waiting for /dev to be fully populated... 16 70 00 | |
| 00 | |
| 08 | |
| 00 | |
| 00 | |
| 00 | |
| 00 | |
| 01 | |
| 10 | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| 28 | |
| 00 | |
| 00 | |
| 01 | |
| 2e | |
| 6a | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| 08 | |
| 00 | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| 2e ba 00 00 08 00 | |
| 08 | |
| 00 | |
| 28 | |
| 00 | |
| 00 | |
| 00 03 00 00 00 08 00 | |
| 00 | |
| 08 | |
| 00 | |
| 01 | |
| 2f | |
| 12 | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| 3a | |
| 00 | |
| 00 | |
| 08 | |
| 00 | |
| 03 | |
| 78 | |
| 00 | |
| 00 08 00 | |
| kjournald starting. Commit interval 5 seconds | |
| EXT3 FS on sdb2, internal journal | |
| EXT3-fs: mounted filesystem with writeback data mode. | |
| [ ok done. | |
| [....] Activating swap...[ ok done. | |
| [....] Cleaning up temporary files... /tmp[ ok . | |
| [....] Activating lvm and md swap...[ ok done. | |
| [....] Checking file systems...fsck from util-linux 2.20.1 | |
| [ ok done. | |
| [....] Mounting local filesystems...[ ok done. | |
| [....] Activating swapfile swap...[ ok done. | |
| [....] Cleaning up temporary files...[ ok . | |
| [....] Setting kernel variables ...[ ok done. | |
| [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.2.2 | |
| Copyright 2004-2011 Internet Systems Consortium. | |
| All rights reserved. | |
| For info, please visit https://www.isc.org/software/dhcp/ | |
| eth0: device MAC address 24:cf:21:b4:a0:16 | |
| STMMAC MII Bus: probed | |
| eth0: PHY ID 01018f2d at 17 IRQ 0 (0:11) active | |
| stmmac_timer: (eth0) sh_tmu Timer (freq 256Hz) | |
| No MAC Management Counters available | |
| Listening on LPF/eth0/24:cf:21:b4:a0:16 | |
| Sending on LPF/eth0/24:cf:21:b4:a0:16 | |
| Sending on Socket/fallback | |
| DHCPREQUEST on eth0 to 255.255.255.255 port 67 | |
| DHCPREQUEST on eth0 to 255.255.255.255 port 67 | |
| DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 | |
| DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 20 | |
| DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 20 | |
| DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 | |
| No DHCPOFFERS received. | |
| Trying recorded lease 192.168.0.9 | |
| PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. | |
| --- 192.168.0.1 ping statistics --- | |
| 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 4ms | |
| No working leases in persistent database - sleeping. | |
| [ ok done. | |
| [....] Cleaning up temporary files...[ ok . | |
| INIT: Entering runlevel: 2 | |
| [info] Using makefile-style concurrent boot in runlevel 2. | |
| [....] Starting enhanced syslogd: rsyslogd[ ok . | |
| [....] Starting periodic command scheduler: cron[ ok . | |
| Starting Dropbear SSH server: dropbear. | |
| Exiting, name server cannot be used: Temporary failure in name resolution (-3) 1 Jan 08:02:16 ntpdate[2009]: name server cannot be used: Temporary failure in name resolution (-3) | |
| [....] startpar: service(s) returned failure: rc.local ...[FAIL failed! | |
| Debian GNU/Linux 7.0 debian-wheezy-sh4 ttyAS0 | |
| debian-wheezy-sh4 login: | |
| Board: STx7105-PDK [32-bit mode] | |
| U-Boot 1.3.1 (Oct 6 2013 - 04:36:18) - stm23_0045 | |
| DRAM: 256 MiB | |
| SPI: ST M25P80 (1MiB) device (page=256,erase=4096) | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| UBOOTWPDA version: 8365896 | |
| swUpdate.c:1024 RESET pressed, 'Red' LED trying external USB at first | |
| (Re)start USB... | |
| USB: scanning bus for devices... 2 USB Device(s) found | |
| scanning bus for storage devices... 1 Storage Device(s) found | |
| Failed to mount ext2 filesystem... | |
| reading uboot.sh | |
| ** Unable to read "uboot.sh" from usb 0:1 ** | |
| Failed to mount ext2 filesystem... | |
| reading iptvubootupdate.bin | |
| ................................................... | |
| 524360 bytes read | |
| swUpdate.c:772 UBOOT_Ver: File:8365896 Flash:8365896 | |
| swUpdate.c:980 skip upgrade same version iptvubootupdate.bin | |
| 843 bytes read | |
| load_uboot_env.c:31 = uboot.sh content= | |
| =# UBOOTWPDA config http://www.twpda.com/2013/08/uboot-code.html | |
| # NOTE: This file's length should under 988 bytes | |
| # bootargs(old): root=8:1 means sda1, sda2 8:2, sdb1 8:17, sdb2 8:18 | |
| # bootargs(new): root=/dev/sda2 | |
| # bootcmd: 0:1 first part, 0:2 2nd part | |
| # usbcfg: 0:internal, 1:external | |
| # boot settings for sh4twbox install disk | |
| # * bootargs: root=8:1 means sda1, sda2 8:2, sdb1 8:17, sdb2 8:18 | |
| # * bootcmd: 0:1 first usb parition, 0:2 2nd usb parition | |
| setenv bootargs 'console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:10:08:E2:12:06:BD phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048' | |
| #setenv bootcmd 'usbcfg 0; usb start; usb info; usb part; ext2load usb 0:1 80000000 vmlinux.ub; bootm 80000000' | |
| setenv bootcmd 'fatload usb 0:1 80000000 vmlinux.ub; bootm 80000000' | |
| = end of uboot.sh = | |
| Hit any key to stop autoboot: 0 | |
| reading vmlinux.ub | |
| ...................................................................................................................................................................................................................................................................................................... | |
| 3020623 bytes read | |
| ## Booting image at 80000000 ... | |
| Image Name: Linux-2.6.32.59-7641-PDK7105-32B | |
| Image Type: SuperH Linux Kernel Image (gzip compressed) | |
| Data Size: 3020559 Bytes = 2.9 MiB | |
| Load Address: 80800000 | |
| Entry Point: 80801000 | |
| Verifying Checksum ... OK | |
| Uncompressing Kernel Image ... OK | |
| CMDLen=186 | |
| There is "hwaddr" keywords! Position=112 | |
| Read MacAddr=24cf21b4a016 | |
| [iptv_kernel]:Starting kernel console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:a0:16 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 - 0x00000000 - 0 ... | |
| Linux version 2.6.32.59-7641-PDK7105-32BITS (dlin@u40) (gcc version 4.7.3 20130514 (STMicroelectronics/Linux Base 4.7.3-124) (GCC) ) #4 PREEMPT Thu Oct 24 15:10:15 CST 2013 | |
| Boot params: | |
| ... MOUNT_ROOT_RDONLY - 00000001 | |
| ... RAMDISK_FLAGS - 00000000 | |
| ... ORIG_ROOT_DEV - 00000200 | |
| ... LOADER_TYPE - 00000000 | |
| ... INITRD_START - 00000000 | |
| ... INITRD_SIZE - 00000000 | |
| Booting machvec: pdk7105 | |
| Node 0: start_pfn = 0x40000, low = 0x50000 | |
| Zone PFN ranges: | |
| Normal 0x00040000 -> 0x00050000 | |
| Movable zone start PFN for each node | |
| early_node_map[1] active PFN ranges | |
| 0: 0x00040000 -> 0x00050000 | |
| STMicroelectronics PDK7105-SDK board initialisation | |
| STx7105 version 3.x | |
| Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 | |
| Kernel command line: console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:a0:16 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 | |
| bpa2: partition 'bigphysarea' created at 0x40f2b000, size 8192 kB (0x00800000 B) | |
| PID hash table entries: 1024 (order: 0, 4096 bytes) | |
| Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
| PVR=04909200 CVR=60880000 PRR=00009e20 | |
| I-cache : n_ways=2 n_sets=512 way_incr=16384 | |
| I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
| D-cache : n_ways=2 n_sets=512 way_incr=16384 | |
| D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 | |
| Memory: 238080k/262144k available (3610k kernel code, 1349k data, 148k init) | |
| Hierarchical RCU implementation. | |
| NR_IRQS:600 | |
| Failed to enable clk CLKA_REF, ignoring | |
| Failed to enable clk CLKA_PLL0LS, ignoring | |
| Console: colour dummy device 80x25 | |
| console [ttyAS0] enabled | |
| sh_tmu: TMU0 used for clock events | |
| sh_tmu: TMU0 used for periodic clock events | |
| sh_tmu: TMU1 used as clock source | |
| Calibrating delay loop... 448.51 BogoMIPS (lpj=897024) | |
| Mount-cache hash table entries: 512 | |
| CPU: STx7105 | |
| [STM][PM-Sys]: ilc3 @ 4096 | |
| NET: Registered protocol family 16 | |
| Configuring FLASH for boot-from-spi: boot_mode=2 | |
| bio: create slab <bio-0> at 0 | |
| SCSI subsystem initialized | |
| usbcore: registered new interface driver usbfs | |
| usbcore: registered new interface driver hub | |
| usbcore: registered new device driver usb | |
| DMA: Registering DMA API. | |
| Switching to clocksource TMU1 | |
| sh_tmu: TMU0 used for oneshot clock events | |
| Switched to NOHz mode on CPU #0 | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
| TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| TCP: Hash tables configured (established 8192 bind 8192) | |
| TCP reno registered | |
| NET: Registered protocol family 1 | |
| RPC: Registered udp transport module. | |
| RPC: Registered tcp transport module. | |
| RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| sq: Registering store queue API. | |
| [STM]: [CPUFreq] Registered | |
| [STM]: [PM]: Suspend support registered | |
| Slow work thread pool: Starting up | |
| Slow work thread pool: Ready | |
| NTFS driver 2.1.29 [Flags: R/O]. | |
| JFFS2 version 2.2. (NAND) 穢 2001-2006 Red Hat, Inc. | |
| ROMFS MTD (C) 2007 Red Hat, Inc. | |
| fuse init (API version 7.13) | |
| msgmni has been set to 465 | |
| alg: No test for stdrng (krng) | |
| io scheduler noop registered | |
| io scheduler anticipatory registered | |
| io scheduler deadline registered | |
| io scheduler cfq registered (default) | |
| lirc_dev: IR Remote Control driver registered, major 61 | |
| lirc-stm: probe found data for platform device lirc-stm | |
| lirc-stm: STM LIRC plugin using IRQ 125 in IR mode | |
| lirc_dev: lirc_register_driver: sample_rate: 0 | |
| STMicroelectronics LIRC driver initialized. | |
| STMicroelectronics ASC driver initialized | |
| stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc | |
| Uniform Multi-Platform E-IDE driver | |
| ide-gd driver 1.18 | |
| MiPHY driver style MiPHY3-65 probed successfully | |
| MiPHY3-65, c1.5 Claimed by sata-stm | |
| scsi0 : sata-stm | |
| ata1: SATA max UDMA/133 irq 72 | |
| ata1: SATA link down (SStatus 0 SControl 0) | |
| physmap platform flash device: 00000000 at 00000000 | |
| physmap-flash physmap-flash.0: Could not reserve memory region | |
| physmap-flash: probe of physmap-flash.0 failed with error -12 | |
| stmmac - user ID: 0x10, Synopsys ID: 0x33 | |
| No HW DMA feature register supported | |
| Enhanced/Alternate descriptors | |
| RX Checksum Offload Engine supported | |
| TX Checksum insertion supported | |
| Wake-Up On Lan supported | |
| nwhw_config: (eth0) setting mac address: 24:cf:21:b4:a0:16 | |
| usbmon: debugfs is not available | |
| ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| stm_usb_probe: usb_phy_clk clock not found for stm-usb.0 | |
| stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller | |
| stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1 | |
| stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00 | |
| stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00 | |
| usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 | |
| usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb1: Product: STMicroelectronics EHCI Host Controller | |
| usb usb1: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ehci_hcd | |
| usb usb1: SerialNumber: stm-ehci.0 | |
| usb usb1: configuration #1 chosen from 1 choice | |
| hub 1-0:1.0: USB hub found | |
| hub 1-0:1.0: 1 port detected | |
| stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller | |
| stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2 | |
| stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00 | |
| usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 | |
| usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb2: Product: STMicroelectronics OHCI Host Controller | |
| usb usb2: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ohci_hcd | |
| usb usb2: SerialNumber: stm-ohci.0 | |
| usb usb2: configuration #1 chosen from 1 choice | |
| hub 2-0:1.0: USB hub found | |
| hub 2-0:1.0: 1 port detected | |
| Initializing USB Mass Storage driver... | |
| usbcore: registered new interface driver usb-storage | |
| USB Mass Storage support registered. | |
| i2c /dev entries driver | |
| cpuidle: using governor ladder | |
| cpuidle: using governor menu | |
| sh_tmu: TMU0 kept as earlytimer | |
| sh_tmu: TMU1 kept as earlytimer | |
| usbcore: registered new interface driver usbhid | |
| usbhid: v2.6:USB HID core driver | |
| [STM][PM-Sys]: emi @ 40 | |
| [STM][PM-Sys]: gpio @ 20 | |
| STMicroelectronics - Coprocessors st231 Init | |
| st-coprocessor-0: No RAM reserved | |
| st231.0 Coprocessor ------------------------------------------- | |
| not configured! | |
| --------------------------------------------------------------- | |
| st-coprocessor-1: No RAM reserved | |
| st231.1 Coprocessor ------------------------------------------- | |
| not configured! | |
| --------------------------------------------------------------- | |
| DMA: Registering fdma_dmac.0 handler (16 channels). | |
| IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs | |
| DMA: Registering fdma_dmac.1 handler (16 channels). | |
| IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs | |
| stm-rng hardware driver 1.0 configured | |
| stm-rtc stm-rtc: rtc core: registered stm-rtc as rtc0 | |
| ip_tables: (C) 2000-2006 Netfilter Core Team | |
| TCP cubic registered | |
| NET: Registered protocol family 17 | |
| stm-rtc stm-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) | |
| usb 1-1: new high speed USB device using stm-ehci and address 2 | |
| usb 1-1: New USB device found, idVendor=090c, idProduct=1000 | |
| usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| usb 1-1: Product: USB Flash Disk | |
| usb 1-1: Manufacturer: General | |
| usb 1-1: SerialNumber: TT00000000009625 | |
| usb 1-1: configuration #1 chosen from 1 choice | |
| scsi1 : SCSI emulation for USB Mass Storage devices | |
| stm_usb_probe: usb_phy_clk clock not found for stm-usb.1 | |
| stm-ehci stm-ehci.1: STMicroelectronics EHCI Host Controller | |
| stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3 | |
| stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00 | |
| stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00 | |
| usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 | |
| usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb3: Product: STMicroelectronics EHCI Host Controller | |
| usb usb3: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ehci_hcd | |
| usb usb3: SerialNumber: stm-ehci.1 | |
| usb usb3: configuration #1 chosen from 1 choice | |
| hub 3-0:1.0: USB hub found | |
| hub 3-0:1.0: 1 port detected | |
| stm-ohci stm-ohci.1: STMicroelectronics OHCI Host Controller | |
| stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4 | |
| stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00 | |
| usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 | |
| usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 | |
| usb usb4: Product: STMicroelectronics OHCI Host Controller | |
| usb usb4: Manufacturer: Linux 2.6.32.59-7641-PDK7105-32BITS ohci_hcd | |
| usb usb4: SerialNumber: stm-ohci.1 | |
| usb usb4: configuration #1 chosen from 1 choice | |
| hub 4-0:1.0: USB hub found | |
| hub 4-0:1.0: 1 port detected | |
| usb 3-1: new high speed USB device using stm-ehci and address 2 | |
| usb 3-1: New USB device found, idVendor=0781, idProduct=5571 | |
| usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 | |
| usb 3-1: Product: Cruzer Fit | |
| usb 3-1: Manufacturer: SanDisk | |
| usb 3-1: SerialNumber: 4C532000060317113330 | |
| usb 3-1: configuration #1 chosen from 1 choice | |
| scsi2 : SCSI emulation for USB Mass Storage devices | |
| scsi 1:0:0:0: Direct-Access General USB Flash Disk 1100 PQ: 0 ANSI: 0 CCS | |
| scsi 2:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 5 | |
| sd 1:0:0:0: Attached scsi generic sg0 type 0 | |
| sd 1:0:0:0: [sda] 15679488 512-byte logical blocks: (8.02 GB/7.47 GiB) | |
| sd 2:0:0:0: Attached scsi generic sg1 type 0 | |
| sd 1:0:0:0: [sda] Write Protect is off | |
| sd 2:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB) | |
| sd 1:0:0:0: [sda] Assuming drive cache: write through | |
| sd 2:0:0:0: [sdb] Write Protect is off | |
| sd 2:0:0:0: [sdb] Assuming drive cache: write through | |
| sd 1:0:0:0: [sda] Assuming drive cache: write through | |
| sda: | |
| sd 2:0:0:0: [sdb] Assuming drive cache: write through | |
| sdb: | |
| sdb1 sdb2 | |
| sd 2:0:0:0: [sdb] Assuming drive cache: write through | |
| sd 2:0:0:0: [sdb] Attached SCSI removable disk | |
| sda1 sda2 | |
| sd 1:0:0:0: [sda] Assuming drive cache: write through | |
| sd 1:0:0:0: [sda] Attached SCSI removable disk | |
| kjournald starting. Commit interval 5 seconds | |
| EXT3 FS on sdb2, internal journal | |
| EXT3-fs: recovery complete. | |
| EXT3-fs: mounted filesystem with journal data mode. | |
| VFS: Mounted root (ext3 filesystem) on device 8:18. | |
| Freeing unused kernel memory: 148k freed | |
| *** running: /etc/init.d/rcS call_by_inittab | |
| dbg:mount fs | |
| dbg:proc/cmdline: console=ttyAS0,115200 rootdelay=0 root=/dev/sdb2 rootfstype=ext3 rw rootflags=data=journal nwhwconf=device:eth0,hwaddr:24:cf:21:b4:a0:16 phyaddr:0,watchdog:5000 mem=256M bigphysarea=2048 | |
| dbg:remount root rw | |
| dbg:get hostname | |
| dbg:mdev -s | |
| dbg:mount devpts | |
| dbg:sysctl -p | |
| net.ipv4.tcp_adv_win_scale = 7 | |
| net.ipv4.tcp_congestion_control = cubic | |
| net.ipv4.tcp_max_syn_backlog = 2048 | |
| net.ipv4.tcp_no_metrics_save = 1 | |
| net.ipv4.tcp_rmem = 10240 87380 262144 | |
| net.ipv4.tcp_wmem = 10240 87380 262144 | |
| net.ipv4.tcp_window_scaling = 1 | |
| net.core.wmem_max = 262144 | |
| net.core.rmem_max = 262144 | |
| net.ipv4.tcp_tw_recycle = 1 | |
| net.ipv4.tcp_fin_timeout = 15 | |
| net.ipv4.tcp_timestamps = 0 | |
| net.ipv4.tcp_sack = 0 | |
| dbg:net | |
| dbg:/etc/init.d/udhcpc | |
| eth0: device MAC address 24:cf:21:b4:a0:16 | |
| dbg:/etc/init.d/backupip backup ip=192.168.168.168 | |
| STMMAC MII Bus: probed | |
| eth0: PHY ID 01018f2d at 17 IRQ 0 (0:11) active | |
| stmmac_timer: (eth0) sh_tmu Timer (freq 256Hz) | |
| No MAC Management Counters available | |
| dbg:services | |
| dbg:starting service telnetd | |
| dbg:/etc/init.d/telnetd | |
| dbg:starting service ntpd | |
| dbg:/etc/init.d/ntpd in background Sat Jan 1 08:00:12 CST 2000 | |
| dbg:starting service crond | |
| dbg:/etc/init.d/crond in background Sat Jan 1 08:00:13 CST 2000 | |
| dbg:calling /etc/rc.local | |
| set to blue | |
| Please press Enter to activate this console. | |
| 08:00:24[0]root@sh4twbox / # | |
| 08:00:25[0]root@sh4twbox / # | |
| 08:00:26[0]root@sh4twbox / # |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment