this is the boot log of booting kernel linux linaro stable 3.10.52 on arndale exynos 5250 board. Display & networking is not working.

dmesg.log

U-Boot 2013.01.-rc1 (Jul 10 2013 - 15:16:09) for ARNDALE5250


CPU:	Exynos5250@1000MHz


Board:  for ARNDALE5250

I2C:   ready

DRAM:  2 GiB

WARNING: Caches not enabled


Checking Boot Mode ... SDMMC

MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1, EXYNOS DWMMC: 2

In:    serial

Out:   serial

Err:   serial

Net:   No ethernet found.

(Re)start USB...

USB0:   USB EHCI 1.00

scanning bus 0 for devices... 4 USB Device(s) found

       scanning usb for storage devices... 0 Storage Device(s) found

       scanning usb for ethernet devices... 1 Ethernet Device(s) found

Hit any key to stop autoboot:  3  2  1  0 

reading uImage

4275976 bytes read

reading uInitrd

2605921 bytes read

reading board.dtb

28774 bytes read

## Booting kernel from Legacy Image at 40007000 ...

   Image Name:   Linux kernel 3.10-52

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    4275912 Bytes = 4.1 MiB

   Load Address: 40008000

   Entry Point:  40008000

   Verifying Checksum ... OK

## Loading init Ramdisk from Legacy Image at 42000000 ...

   Image Name:   initramfs

   Image Type:   ARM Linux RAMDisk Image (uncompressed)

   Data Size:    2605857 Bytes = 2.5 MiB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

## Flattened Device Tree blob at 41f00000

   Booting using the fdt blob at 0x41f00000

   Loading Kernel Image ... OK

OK

   Using Device Tree in place at 41f00000, end 41f0a065


Starting kernel ...


[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.10.52 (slabs@slabs-UX31E) (gcc version 4.8.3 20140401 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.04 - Linaro GCC 4.8-2014.04) ) #1 SMP Tue May 19 18:03:16 IST 2015
[    0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: SAMSUNG EXYNOS5 (Flattened Device Tree), model: Insignal Arndale evaluation board based on EXYNOS5250
[    0.000000] NR_BANKS too low, ignoring high memory
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU EXYNOS5250 (id 0x43520010)
[    0.000000] PERCPU: Embedded 9 pages/cpu @817a6000 s14464 r8192 d14208 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 514576
[    0.000000] Kernel command line: console=tty0 console=ttySAC2,115200n8 drm_kms_helper.edid_firmware=edid-1920x1080.fw  root=UUID=a9b2def7-9fa1-423f-acb0-3725791a719b rootwait ro mac=02:0c:cc:99:a9:04
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Memory: 48MB 216MB 1504MB 256MB = 2024MB total
[    0.000000] Memory: 2044164k/2060548k available, 28412k reserved, 262144K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xef800000   (1784 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f800000 - 0x7fe00000   (   6 MB)
[    0.000000]       .text : 0x80008000 - 0x80646934   (6395 kB)
[    0.000000]       .init : 0x80647000 - 0x806a0880   ( 359 kB)
[    0.000000]       .data : 0x806a2000 - 0x8070f7e8   ( 438 kB)
[    0.000000]        .bss : 0x8070f7e8 - 0x807864a8   ( 476 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:549
[    0.000000] Exynos5250: clock setup completed, armclk=1000000000
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[    0.000000] sched_clock: 32 bits at 200 Hz, resolution 5000000ns, wraps every 4294967291ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty0] enabled
[    0.000942] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000)
[    0.000979] pid_max: default: 32768 minimum: 301
[    0.001121] Security Framework initialized
[    0.001151] AppArmor: AppArmor initialized
[    0.001214] Mount-cache hash table entries: 512
[    0.012821] CPU: Testing write buffer coherency: ok
[    0.012867] ftrace: allocating 22872 entries in 45 pages
[    0.033185] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.033230] Setting up static identity map for 0x80435bc8 - 0x80435c14
[    0.034283] CPU1: Booted secondary processor
[    0.034311] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.034425] Brought up 2 CPUs
[    0.034453] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.034463] CPU: All CPU(s) started in HYP mode.
[    0.034473] CPU: Virtualization extensions available.
[    0.035043] devtmpfs: initialized
[    0.046107] xor: measuring software checksum speed
[    0.092073]    arm4regs  :  1764.800 MB/sec
[    0.141312]    8regs     :  1743.200 MB/sec
[    0.190550]    32regs    :  1424.000 MB/sec
[    0.190562] xor: using function: arm4regs (1764.800 MB/sec)
[    0.190575] pinctrl core: initialized pinctrl subsystem
[    0.191073] regulator-dummy: no parameters
[    0.191358] NET: Registered protocol family 16
[    0.191527] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.200727] of_clk_src_onecell_get: invalid clock index 346
[    0.200743] ERROR: could not get clock /amba/mdma@10800000:apb_pclk(0)
[    0.202644] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.202661] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.202701] S3C Power Management, Copyright 2004 Simtec Electronics
[    0.202799] EXYNOS5250 PMU Initialize
[    0.202809] EXYNOS: Initializing architecture
[    0.219045] bio: create slab <bio-0> at 0
[    0.299114] raid6: int32x1    196 MB/s
[    0.382734] raid6: int32x2    300 MB/s
[    0.466509] raid6: int32x4    328 MB/s
[    0.550169] raid6: int32x8    473 MB/s
[    0.550179] raid6: using algorithm int32x8 (473 MB/s)
[    0.550190] raid6: using intx1 recovery algorithm
[    0.550602] VDD_33ON_2.8V: 2800 mV 
[    0.550812] hdmi-en: no parameters
[    0.551706] SCSI subsystem initialized
[    0.552547] usbcore: registered new interface driver usbfs
[    0.552660] usbcore: registered new interface driver hub
[    0.552811] usbcore: registered new device driver usb
[    0.553347] s3c-i2c 12c60000.i2c: slave address 0x66
[    0.553364] s3c-i2c 12c60000.i2c: bus frequency set to 18 KHz
[    0.553948] sec_pmic 0-0066: No interrupt specified, no interrupts
[    0.599370] VDD_ALIVE_1.0V: 1100 mV 
[    0.624016] VDD_28IO_DP_1.35V: 1200 mV 
[    0.648664] VDD_COMMON1_1.8V: 1800 mV 
[    0.668382] VDD_IOPERI_1.8V: 1800 mV 
[    0.693031] VDD_EXT_1.8V: 1800 mV 
[    0.717668] VDD_MPLL_1.1V: 1100 mV 
[    0.742312] VDD_XPLL_1.1V: 1100 mV 
[    0.766963] VDD_COMMON2_1.0V: 1000 mV 
[    0.786677] VDD_33ON_3.0V: 3000 mV 
[    0.811322] VDD_COMMON3_1.8V: 1800 mV 
[    0.835965] VDD_ABB2_1.8V: 1800 mV 
[    0.860610] VDD_USB_3.0V: 3000 mV 
[    0.885253] VDDQ_C2C_W_1.8V: 1800 mV 
[    0.909899] VDD18_ABB0_3_1.8V: 1800 mV 
[    0.934543] VDD10_COMMON4_1.0V: 1000 mV 
[    0.959186] VDD18_HSIC_1.8V: 1800 mV 
[    0.983828] VDDQ_MMC2_3_2.8V: 2800 mV 
[    1.003546] VDD_33ON_2.8V: 2800 mV 
[    1.008496] VDD_33ON_2.8V: Failed to create debugfs directory
[    1.023266] EXT_33_OFF: 3300 mV 
[    1.042980] EXT_28_OFF: 2800 mV 
[    1.062696] PVDD_LDO25: 1200 mV 
[    1.082412] EXT_18_OFF: 1800 mV 
[    1.097197] vdd_mif: 950 <--> 1200 mV at 1000 mV 
[    1.111984] vdd_arm: 925 <--> 1300 mV at 1100 mV 
[    1.126792] vdd_int: 900 <--> 1200 mV at 1000 mV 
[    1.151417] vdd_g3d: 1000 mV 
[    1.166211] VDD_MEM_1.35V: 750 <--> 1350 mV at 1200 mV 
[    1.176063] VDD_33_OFF_EXT1: 750 <--> 3000 mV at 2850 mV 
[    1.181177] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter
[    1.181262] s3c-i2c 12ce0000.i2c: slave address 0x00
[    1.181278] s3c-i2c 12ce0000.i2c: bus frequency set to 65 KHz
[    1.181446] s3c-i2c 12ce0000.i2c: i2c-8: S3C I2C adapter
[    1.182546] NetLabel: Initializing
[    1.182559] NetLabel:  domain hash size = 128
[    1.182568] NetLabel:  protocols = UNLABELED CIPSOv4
[    1.182628] NetLabel:  unlabeled traffic allowed by default
[    1.182726] Switching to clocksource arch_sys_counter
[    1.195892] AppArmor: AppArmor Filesystem Enabled
[    1.207328] NET: Registered protocol family 2
[    1.207766] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.208040] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
[    1.208345] TCP: Hash tables configured (established 16384 bind 16384)
[    1.208394] TCP: reno registered
[    1.208411] UDP hash table entries: 1024 (order: 3, 49152 bytes)
[    1.208477] UDP-Lite hash table entries: 1024 (order: 3, 49152 bytes)
[    1.208695] NET: Registered protocol family 1
[    1.208914] RPC: Registered named UNIX socket transport module.
[    1.208928] RPC: Registered udp transport module.
[    1.208938] RPC: Registered tcp transport module.
[    1.208948] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.209091] Trying to unpack rootfs image as initramfs...
[    1.321709] Freeing initrd memory: 2540K (82001000 - 8227c000)
[    1.321908] hw perfevents: enabled with ARMv7_Cortex_A15 PMU driver, 7 counters available
[    1.322913] audit: initializing netlink socket (disabled)
[    1.322945] type=2000 audit(1.330:1): initialized
[    1.324017] bounce pool size: 64 pages
[    1.324171] VFS: Disk quotas dquot_6.5.2
[    1.324280] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.324990] NFS: Registering the id_resolver key type
[    1.325025] Key type id_resolver registered
[    1.325036] Key type id_legacy registered
[    1.325068] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.325530] bio: create slab <bio-1> at 1
[    1.325838] Btrfs loaded
[    1.325858] msgmni has been set to 3485
[    1.326400] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.326418] io scheduler noop registered
[    1.326429] io scheduler deadline registered
[    1.326461] io scheduler cfq registered (default)
[    1.335383] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-2364208
[    1.335403] dma-pl330 121a0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.339531] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-2364208
[    1.339551] dma-pl330 121b0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.340749] dma-pl330 11c10000.mdma: Loaded driver for PL330 DMAC-2364208
[    1.340766] dma-pl330 11c10000.mdma: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    1.414412] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.415644] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 83) is a S3C6400/10
[    1.415925] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 84) is a S3C6400/10
[    1.416191] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 85) is a S3C6400/10
[    2.268573] console [ttySAC2] enabled
[    2.272502] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 86) is a S3C6400/10
[    2.280172] [drm] Initialized drm 1.1.0 20060810
[    2.291284] exynos-mixer 14450000.mixer: probe start
[    2.294738] exynos-mixer 14450000.mixer: failed to get clock 'mixer'
[    2.300958] [drm:mixer_probe] *ERROR* mixer_resources_init failed
[    2.306937] exynos-mixer 14450000.mixer: probe failed
[    2.313055] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    2.318391] [drm] No driver support for vblank timestamp query.
[    2.324191] [drm:hdmi_subdrv_probe] *ERROR* mixer context not initialized.
[    2.331408] exynos-drm: probe of exynos-drm failed with error -22
[    2.343652] brd: module loaded
[    2.348775] loop: module loaded
[    2.351597] mtdoops: mtd device (mtddev=name/number) must be supplied
[    2.356757] tun: Universal TUN/TAP device driver, 1.6
[    2.361812] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.368208] usbcore: registered new interface driver asix
[    2.373168] usbcore: registered new interface driver ax88179_178a
[    2.379136] usbcore: registered new interface driver cdc_ether
[    2.384858] usbcore: registered new interface driver net1080
[    2.390418] usbcore: registered new interface driver cdc_subset
[    2.396216] usbcore: registered new interface driver zaurus
[    2.401715] usbcore: registered new interface driver cdc_ncm
[    2.407140] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.413558] ehci-s5p: EHCI s5p driver
[    2.417191] unable to find transceiver of type USB2 PHY
[    2.422263] s5p-ehci 12110000.usb: no platform data or transceiver defined
[    2.429013] platform 12110000.usb: Driver s5p-ehci requests probe deferral
[    2.435861] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.442015] unable to find transceiver of type USB2 PHY
[    2.446959] exynos-ohci 12120000.usb: no platform data or transceiver defined
[    2.453954] platform 12120000.usb: Driver exynos-ohci requests probe deferral
[    2.461813] mousedev: PS/2 mouse device common for all mice
[    2.467738] Exynos: Kernel Thermal management registered
[    2.471985] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    2.480140] cpuidle: using governor ladder
[    2.484006] cpuidle: using governor menu
[    2.487892] Synopsys Designware Multimedia Card Interface Driver
[    2.494051] dwmmc_exynos 12200000.dwmmc0: Using internal DMA controller.
[    2.500258] dwmmc_exynos 12200000.dwmmc0: Version ID is 241a
[    2.505883] dwmmc_exynos 12200000.dwmmc0: DW MMC controller at irq 107, 32 bit host data width, 128 deep fifo
[    2.525938] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[    2.545662] dwmmc_exynos 12200000.dwmmc0: 1 slots initialized
[    2.550048] dwmmc_exynos 12220000.dwmmc2: Using internal DMA controller.
[    2.556458] dwmmc_exynos 12220000.dwmmc2: Version ID is 241a
[    2.562084] dwmmc_exynos 12220000.dwmmc2: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo
[    2.584983] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[    2.593067] mmc0: BKOPS_EN bit is not set
[    2.598174] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[    2.606675] dwmmc_exynos 12220000.dwmmc2: 1 slots initialized
[    2.606882] mmc0: new high speed DDR MMC card at address 0001
[    2.607489] mmcblk0: mmc0:0001 M8G1WA 7.28 GiB 
[    2.607701] mmcblk0boot0: mmc0:0001 M8G1WA partition 1 2.00 MiB
[    2.607895] mmcblk0boot1: mmc0:0001 M8G1WA partition 2 2.00 MiB
[    2.608082] mmcblk0rpmb: mmc0:0001 M8G1WA partition 3 128 KiB
[    2.609067]  mmcblk0: p1 p2 p3 p4
[    2.612807]  mmcblk0boot1: unknown partition table
[    2.614093]  mmcblk0boot0: unknown partition table
[    2.652735] usbcore: registered new interface driver usbhid
[    2.657706] usbhid: USB HID core driver
[    2.661974] oprofile: using timer interrupt.
[    2.662721] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 50000000Hz, actual 50000000HZ div = 1)
[    2.662794] mmc1: new high speed SDHC card at address 1234
[    2.663356] mmcblk1: mmc1:1234 SA16G 14.4 GiB 
[    2.665062]  mmcblk1: p1 p2 p3
[    2.688228] TCP: cubic registered
[    2.691264] Initializing XFRM netlink socket
[    2.695511] NET: Registered protocol family 10
[    2.700277] sit: IPv6 over IPv4 tunneling driver
[    2.704938] NET: Registered protocol family 17
[    2.708710] NET: Registered protocol family 15
[    2.713152] Key type dns_resolver registered
[    2.717298] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    2.724764] Registering SWP/SWPB emulation handler
[    2.729753] mfc-power-domain: Power-off latency exceeded, new value 260167 ns
[    2.736461] gsc-power-domain: Power-off latency exceeded, new value 6997875 ns
[    2.745301] EXT_28_OFF: disabling
[    2.753406] VDD_33ON_2.8V: disabling
[    2.761765] hdmi-en: disabling
[    2.763329] regulator-dummy: disabling
[    2.767266] s5p-ehci 12110000.usb: EHCI Host Controller
[    2.772137] s5p-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    2.779431] s5p-ehci 12110000.usb: irq 103, io mem 0x12110000
[    2.791623] s5p-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    2.796363] hub 1-0:1.0: USB hub found
[    2.799516] hub 1-0:1.0: 3 ports detected
[    2.803737] samsung-usb2phy 12130000.usbphy: Already power on PHY
[    2.809415] exynos-ohci 12120000.usb: EXYNOS OHCI Host Controller
[    2.815399] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    2.822934] exynos-ohci 12120000.usb: irq 103, io mem 0x12120000
[    2.884634] hub 2-0:1.0: USB hub found
[    2.886891] hub 2-0:1.0: 3 ports detected
[    2.891713] input: gpio_keys.3 as /devices/gpio_keys.3/input/input0
[    2.897295] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    2.916118] Freeing unused kernel memory: 356K (80647000 - 806a0000)
Loading, please wait...
[    2.944722] systemd-udevd[1208]: starting version 204
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[    3.190963] EXT4-fs (mmcblk1p3): mounted filesystem with ordered data mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
[    3.911152] init: plymouth-upstart-bridge main process (1259) terminated with status 1
[    3.917919] init: plymouth-upstart-bridge main process ended, respawning
[    4.070539] init: plymouth-upstart-bridge main process (1269) terminated with status 1
[    4.077280] init: plymouth-upstart-bridge main process ended, respawning
[    4.095194] init: ureadahead main process (1262) terminated with status 5
[    4.178014] init: plymouth-upstart-bridge main process (1273) terminated with status 1
[    4.184754] init: plymouth-upstart-bridge main process ended, respawning
 * Stopping Send an event to indicate plymouth is up[ OK ]

 * Starting Mount filesystems on boot[ OK ]

 * Starting Populate /dev filesystem[ OK ]

 * Starting Populate and link to /run filesystem[ OK ]

 * Stopping Populate /dev filesystem[ OK ]

 * Stopping Populate and link to /run filesystem[ OK ]

 * Stopping Track if upstart is running in a container[ OK ]

 * Starting Fix-up /sys/kernel/debug filesystem[ OK ]

 * Stopping Fix-up /sys/kernel/debug filesystem[ OK ]

 * Starting Initialize or finalize resolvconf[ OK ]

 * Starting set console keymap[ OK ]

 * Starting Signal sysvinit that virtual filesystems are mounted[ OK ]

 * Starting Signal sysvinit that virtual filesystems are mounted[ OK ]

 * Starting Bridge udev events into upstart[ OK ]

 * Stopping set console keymap[ OK ]

 * Starting Signal sysvinit that remote filesystems are mounted[ OK ]

 * Starting device node and kernel event manager[ OK ]

 * Starting load modules from /etc/modules[ OK ]

 * Starting cold plug devices[ OK ]

 * Starting log initial device creation[ OK ]

 * Starting Signal sysvinit that the rootfs is mounted[ OK ]

 * Stopping load modules from /etc/modules[ OK ]

 * Starting Clean /tmp directory[ OK ]

 * Starting configure network device security[ OK ]

 * Starting configure network device security[ OK ]

 * Starting configure network device[ OK ]

 * Stopping Clean /tmp directory[ OK ]

 * Starting Mount network filesystems[ OK ]

 * Starting Signal sysvinit that local filesystems are mounted[ OK ]

 * Stopping Mount filesystems on boot[ OK ]

 * Starting Failsafe Boot Delay[ OK ]

 * Starting flush early job output to logs[ OK ]

 * Stopping cold plug devices[ OK ]

 * Stopping log initial device creation[ OK ]

 * Stopping flush early job output to logs[ OK ]

 * Starting configure network device security[ OK ]

 * Starting D-Bus system message bus[ OK ]

 * Starting userspace bootsplash[ OK ]

 * Stopping userspace bootsplash[ OK ]

 * Starting Send an event to indicate plymouth is up[ OK ]

 * Starting configure network device[ OK ]

 * Starting SystemD login management service[ OK ]

 * Stopping Mount network filesystems[ OK ]

 * Starting configure virtual network devices[ OK ]

 * Stopping Send an event to indicate plymouth is up[ OK ]

 * Starting system logging daemon[ OK ]

 * Starting mDNS/DNS-SD daemon[ OK ]

 * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated[ OK ]

 * Starting Reload cups, upon starting avahi-daemon to make sure remote queues are populated[fail]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting Bridge file events into upstart[ OK ]

 * Starting Bridge socket events into upstart[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[ OK ]

 * Starting bluetooth daemon[fail]

 * Stopping bluetooth daemon[ OK ]

Waiting for network configuration...

Waiting up to 60 more seconds for network configuration...

Booting system without full network configuration...

 * Stopping Failsafe Boot Delay[ OK ]

 * Starting System V initialisation compatibility[ OK ]

 * Setting up X socket directories...        
[ OK ]

 * Stopping System V initialisation compatibility[ OK ]



Last login: Thu Jan  1 00:02:10 UTC 1970 on tty1
Welcome to Linaro 14.04 (GNU/Linux 3.10.52 armv7l)

 * Documentation:  https://wiki.linaro.org/
root@linaro-alip:~#