TSA1605A Clock

TSA1605A_Clock.ino

// Arduino code for Alarm Clock with TSA1605A 8x14 segments micro leds display 
// Goebish 2013 (twitter: @goebish)
//
// This code is  distributed  in the hope that it  will be useful for everyone  but it  is distributed 
// without any warranty.  It is provided  "as is" without  warranty of  any kind, either  expressed or 
// implied, including, but not limited to, the implied warranties of merchantability and fitness for a
// particular purpose.  The entire risk  as to the  quality and  performance of the  code is with you.
// Should  the code  prove  defective,  you assume  the cost of  all necessary  servicing,  repair  or 
// correction.  In no  event will  the author of the  code be liable  to you  for  damages,  including 
// any general,  special,  incidental or  consequential  damages arising  out of  the use of the code, 
// including  but  not limited to  loss  of life,  money,  the loss  of data or  data  being  rendered 
// inaccurate, or  any other losses  sustained by  you or  third parties  or a failure of  the code to
// operate with any other  device(s), even if the author  has been advised of the  possibility of such 
// possibilities.
//
// pictures:
// http://imgur.com/10iBfZd 
// http://imgur.com/CL1NXCh
//
// parts:
// - atmega168 or atmega328 Arduino or compatible dev board (2009, UNO, nano, mini ...) this has not been tested with the Leonardo and shouldn't work on the MEGA
// - DS1307 RTC + 32.768kHz chrystal + 3V coin battery cell (CR2032) or DS1307 breakout module
// - TSA1605A 8x14 segments micro LEDs display
// - 14x 68 ohms resistors (one for each segments anode, they don't appear in my pictures, but you should really use them ;))
// - 3x 74HC595 shift registers
// - 3x momentary pushbuttons (MODE/SET, PLUS, MINUS) + 3x 0.1µF capacitors
// - 10k ohms resistor (HC595s OE pullup)
// - piezzo buzzer + 100 ohms resistor
// - led + 8k ohms resistor (alarm enabled indicator)
//
// schematics:
// http://imgur.com/2fvOBml
//
// read through the code for usage description :)
 
#include <Wire.h> // I2C for DS1307 RTC
#include <EEPROM.h> // eeprom used to store alarm settings
#include <TimerOne.h>  // get it from http://code.google.com/p/arduino-timerone/
#define NO_PORTC_PINCHANGES
#define NO_PORTD_PINCHANGES
#include <PinChangeInt.h>  // get it from http://code.google.com/p/arduino-pinchangeint/
 
#if (ARDUINO >= 100)
  #define WireWrite Wire.write
  #define WireRead Wire.read()
#else
  #define WireWrite Wire.send
  #define WireRead Wire.receive()
#endif
 
// One side of the pushbuttons is connected to ground. The other sides connect to the Arduino pins. 
// Put a 0.1µF cap between pushbuttons legs to provide hard debouncing
const int setButton = 9;
const int minusButton=10;
const int plusButton =11;
 
const int buzzer=2; // buzzer w/ 100ohms resistor
const int alarmLed=13; // led + 8k ohms resistor, use an high enough resistor value so the led isn't brighter than the display
 
// HC595s wiring:
// HC595-1, 2 & 3 pin 8 to GND
// HC595-1, 2 & 3 pin 10 to +5V
// HC595-1, 2 & 3 pin 16 to +5V
// HC595-1 QA to QH outputs --> TSA1605A cathodes 1 to 8 (pins 1, 22, 3, 19, 8, 15, 11, 12)
// HC595-2 QA to QH outputs --> TSA1605A G to N segments (pins 6, 13, 20, 18, 17, 2, 7, 10)
// HC595-3 QA to QF outputs --> TSA1605A A to F segments (pins 14, 16, 5, 4, 9, 21)
// place one 68 ohms resistor between each display segment anodes and it's HC959 output.
// do not modify the following pins assignments ! (direct port access in ISR, no digitalWrite)
const int dataPin1  = 5; // to HC595-1 (pin 14) cathodes driver
const int dataPin2  = 4; // to HC595-2 (pin 14) segments GHIJKLMN anodes driver
const int dataPin3  = 6; // to HC595-3 (pin 14) segments ABCDEF anodes driver
const int latchPin  = 7; // to HC595-1, 2 & 3 (pin 12)
const int clockPin  = 8; // to HC595-1, 2 & 3 (pin 11)
const int oePin = 3; // to HC595-1, 2 & 3 (pin 13) + 10k pull up resistor to +5V
 
#define DISPLAY_ISR_PERIOD 500 // 1/DISPLAY_ISR_PERIOD/1000 = display frequency, lower value produce brighter display. Don't go to low or the main loop won't have enough (if any) CPU cycles for itself.
//#define DISPLAY_ISR_PERIOD 2000 // for use without resistors on display anodes, USE AT YOUR OWN RISK !
 
 
// DS1307 Real Time Clock
// SDA (pin 5) to Arduino A4
// SCL (pin 6) to Arduino A5
#define DS1307_ADDRESS 0x68
typedef struct {
  byte second;
  byte minute;
  byte hour;
  byte weekDay; 
  byte monthDay;
  byte month;
  int year;
} 
s_dateTime;
volatile s_dateTime curDateTime; 
 
typedef struct {
  byte enabled;
  byte hour;
  byte minute;
} s_alarmSettings;
volatile s_alarmSettings alarm = {false,0,0};
 
// states
typedef enum e_states{ 
  CLOCK,
  DATE,     // return to CLOCK if SET button is not pushed for 5 seconds
  SET_ALARM, // is SET button is pushed while "SET ALARM" is displayed, go directly to "SET_DATE", or wait 2s to enter SET_ALARM_ENABLED
  SET_ALARM_ENABLED, // if OFF is choosen, go to WRITE_ALARM
  SET_ALARM_HOUR,
  SET_ALARM_MINUTE, // go to WRITE_ALARM when done
  SET_DATE, // if SET button is pushed while "SET DATE" is displayed, go directly to "SET TIME", or wait 2s to enter SET_YEAR 
  SET_YEAR,
  SET_MONTH,
  SET_DAY, // go to WRITE_DATETIME after setting day
  SET_TIME, // if SET button is pushed while "SET TIME" is displayed, return to CLOCK mode 
  SET_HOUR,
  SET_MINUTE,
  WRITE_DATETIME, // returns to CLOCK when done
  WRITE_ALARM // returns to CLOCK when done
};
volatile int currentState = CLOCK;
volatile unsigned long mode_start=0;
volatile unsigned long last_button_push=0;
 
const char* clock_format_no_tick = "%02d %02d %02d";
const char* clock_format_tick = "%02d-%02d-%02d";
const char* clock_format_date = "%02d %s";
const char* set_hour_tick = "   %02d   ";
const char* set_hour_no_tick = "%02d %02d   ";
const char* set_minute_tick = "%02d      ";
const char* set_minute_no_tick = set_hour_no_tick;
const char* set_day_tick = "   %s";
const char* set_month_tick = set_minute_tick;
const char* set_year_tick = "  %04d  ";
const char* month[] = {"JANV ","FEV  ","MARS ","AVRIL","MAI  ","JUIN ","JUIL ","AOUT ","SEPT ","OCT  ","NOV  ","DEC  "}; // french months, change them as you like but keep 5 characters per month
const int daysInMonth[12]={31,28,31,30,31,30,31,31,30,31,30,31};
char displayBuffer[9]= "aaaaaaaa"; 
 
// credits go to http://huinink.info/8-x-14-segment/ for most of the ascii table font, I only modified a few numbers to take advantage of the 14 segments
const byte ascii[] PROGMEM={
  0x00, 0x00, // space
  0x01, 0x4A, // !
  0x22, 0x00, // "
  0x0E, 0x55, // #
  0x39, 0x55, // euro. for dollar use 0x2D, 0x55
  0x24, 0x88, // %
  0x1D, 0x2B, // &
  0x00, 0x08, // '
  0x39, 0x00, // {
  0x0F, 0x00, // )
  0x00, 0xFF, // *
  0x00, 0x55, // +
  0x00, 0x80, // ,
  0x00, 0x11, //
  0x08, 0x00, // dot?
  0x00, 0x88, // /
  0x3F, 0x00, // 0
  0x06, 0x08, // 1 
  0x1B, 0x11, // 2 
  0x0F, 0x10, // 3 
  0x26, 0x11, // 4
  0x2D, 0x11, // 5 
  0x3D, 0x11, // 6
  0x01, 0x88, // 7 
  0x3F, 0x11, // 8
  0x2F, 0x11, // 9
  0x01, 0x11, // :
  0x01, 0x80, // ;
  0x00, 0x28, // <
  0x00, 0x82, // >
  0x08, 0x11, // =
  0x03, 0x50, // ?
  0x1F, 0x41, // @
  0x37, 0x11, // A
  0x0F, 0x54, // B
  0x39, 0x00, // C
  0x0F, 0x44, // D
  0x39, 0x01, // E
  0x31, 0x01, // F
  0x3D, 0x10, // G
  0x36, 0x11, // H
  0x09, 0x44, // I
  0x1E, 0x00, // J
  0x30, 0x29, // K
  0x38, 0x00, // L
  0x36, 0x0A, // M
  0x36, 0x22, // N
  0x3F, 0x00, // O
  0x33, 0x11, // P
  0x3F, 0x20, // Q
  0x33, 0x31, // R
  0x2D, 0x11, // S
  0x01, 0x44, // T
  0x3E, 0x00, // U
  0x30, 0x88, // V
  0x36, 0xA0, // W
  0x00, 0xAA, // X
  0x00, 0x4A, // Y
  0x09, 0x88, // Z
  0x39, 0x00, // [
  0x00, 0x88, // /
  0x0F, 0x00, // ]
  0x00, 0xA0, // ^
  0x08, 0x00, // _
  0x00, 0x02, // `
  0x3F, 0xFF  // a --> test character
};
 
void buttonsManager()
{
  if(millis()-last_button_push>150) {
    switch(PCintPort::arduinoPin) {
      case setButton:
        if(currentState == SET_ALARM)
          currentState = SET_DATE;
        else if(currentState == SET_DATE)
          currentState = SET_TIME;
        else if(currentState==SET_TIME)
          currentState = CLOCK;
        else if(currentState==SET_MONTH)
        {
          if( curDateTime.monthDay > daysInMonth[curDateTime.month-1])
            curDateTime.monthDay = daysInMonth[curDateTime.month-1];
          currentState++;  
        }
        else if(currentState == SET_DAY)
          currentState = WRITE_DATETIME;
        else if(currentState == SET_MINUTE)
        {
          curDateTime.second=0;
          currentState = WRITE_DATETIME;  
        }
        else if((currentState==SET_ALARM_ENABLED && alarm.enabled==false) || currentState==SET_ALARM_MINUTE)
          currentState = WRITE_ALARM;
        else
          currentState++;
        mode_start=millis();
        break;
      case minusButton:
        switch(currentState) {
          case SET_HOUR:
            if(curDateTime.hour<=0)
              curDateTime.hour = 23;
            else
              curDateTime.hour--;
            break;
          case SET_MINUTE:
            if(curDateTime.minute<=0)
              curDateTime.minute = 59;
            else
              curDateTime.minute--;
            break;
          case SET_ALARM_ENABLED:
            alarm.enabled = !alarm.enabled;
            digitalWrite(alarmLed, alarm.enabled);
            break;
          case SET_ALARM_HOUR:
            if(alarm.hour<=0)
              alarm.hour = 23;
            else
              alarm.hour--;
            break;
          case SET_ALARM_MINUTE:
            if(alarm.minute<=0)
              alarm.minute = 59;
            else
              alarm.minute--;
            break;
          case SET_MONTH:
            if(curDateTime.month<=1)
              curDateTime.month = 12;
            else
              curDateTime.month--;
            break;
          case SET_DAY:
            if(curDateTime.monthDay <= 1)
              if(isLeapYear(curDateTime.year) && curDateTime.month==2)
                curDateTime.monthDay = 29;
              else
                curDateTime.monthDay = daysInMonth[curDateTime.month-1];
            else
              curDateTime.monthDay--;
            break;
          case SET_YEAR:
            if(curDateTime.year<=2000)
              curDateTime.year = 2099;
            else
              curDateTime.year--;
            break;
        }
        break;
      case plusButton:
        switch(currentState) {
          case SET_HOUR:
            if(curDateTime.hour>=23)
              curDateTime.hour = 0;
            else
              curDateTime.hour++;
            break;
          case SET_MINUTE:
            if(curDateTime.minute>=59)
              curDateTime.minute = 0;
            else
              curDateTime.minute++;
            break;
          case SET_ALARM_ENABLED:
            alarm.enabled = !alarm.enabled;
            digitalWrite(alarmLed, alarm.enabled);
            break;
          case SET_ALARM_HOUR:
            if(alarm.hour>=59)
              alarm.hour = 0;
            else
              alarm.hour++;
            break;
          case SET_ALARM_MINUTE:
            if(alarm.minute>=59)
              alarm.minute = 0;
            else
              alarm.minute++;
            break;
          case SET_MONTH:
            if(curDateTime.month>=12)
              curDateTime.month = 1;
            else
              curDateTime.month++;
            break;
          case SET_DAY:
            if(isLeapYear(curDateTime.year) && curDateTime.month==2 && curDateTime.monthDay>=29) 
              curDateTime.monthDay = 1;
            else if(curDateTime.monthDay >= daysInMonth[curDateTime.month-1])
              curDateTime.monthDay = 1;
            else
              curDateTime.monthDay++;
            break;
          case SET_YEAR:
            if(curDateTime.year>=2099)
              curDateTime.year = 2000;
            else
              curDateTime.year++;
            break;
        }
        break;
    }
    last_button_push = millis();
  }
}
 
void setup()
{
  digitalWrite(oePin, HIGH); // disable output
  pinMode(oePin, OUTPUT);
  pinMode(dataPin1, OUTPUT);
  pinMode(dataPin2, OUTPUT);
  pinMode(dataPin3, OUTPUT);
  pinMode(latchPin, OUTPUT);
  pinMode(clockPin, OUTPUT);
  
  pinMode(buzzer, OUTPUT);
  digitalWrite(buzzer, LOW);
  pinMode(alarmLed, OUTPUT);
  
  // init buttons interrupt
  pinMode(setButton, INPUT);
  digitalWrite(setButton, HIGH);
  PCintPort::attachInterrupt(setButton, &buttonsManager, FALLING);
  pinMode(minusButton, INPUT);
  digitalWrite(minusButton, HIGH);
  PCintPort::attachInterrupt(minusButton, &buttonsManager, FALLING);
  pinMode(plusButton, INPUT);
  digitalWrite(plusButton, HIGH);
  PCintPort::attachInterrupt(plusButton, &buttonsManager, FALLING);
  
  // init I2C bus for DS1307 RTC
  Wire.begin();
  
  // init display interrupt
  Timer1.initialize(DISPLAY_ISR_PERIOD);
  Timer1.attachInterrupt(displayISR);
  
  getAlarmSettings();
  
  delay(1000);
}
 
bool isLeapYear(const int year) {
  return year%4==0; // ok for 2000-2099 because 2000 is leap
}
 
void printDate() {
  sprintf(displayBuffer,clock_format_date,curDateTime.monthDay, month[curDateTime.month-1]);
}
 
void printTime() {
  sprintf(displayBuffer,curDateTime.second%2?clock_format_tick:clock_format_no_tick,curDateTime.hour,curDateTime.minute,curDateTime.second);
}
 
void buzz() {
  unsigned long alarmStart=millis();
  while(digitalRead(setButton==HIGH) && millis()-alarmStart < 60000) { // one minute should be enough to wake up ;)
    updateCurDateTime();
    printTime();
    for(int j=0; j<4; j++) { 
      digitalWrite(buzzer,HIGH);
      delay(90);
      digitalWrite(buzzer,LOW);
      delay(45);
      if(digitalRead(setButton)==LOW) {
        currentState = CLOCK;
        return;
      } 
    }
    sprintf(displayBuffer,"  ALARM ");
    delay(400);
  }
  currentState = CLOCK;
}
 
void loop(){
  bool tick=millis()%600<300 && millis()-last_button_push >  400;
  if(millis()-last_button_push>200 && (digitalRead(minusButton)==LOW || digitalRead(plusButton)==LOW)) { // buttons auto-repeat
    buttonsManager();
  }
  updateCurDateTime();
  switch(currentState) {
    case CLOCK:
      printTime();
      if(alarm.enabled && curDateTime.second==0 && curDateTime.hour==alarm.hour && curDateTime.minute==alarm.minute)
        buzz();
      break;
    case DATE:
      printDate();
      if(millis()-mode_start>5000) // return to clock after 5s
        currentState = CLOCK;
      break;
    case SET_ALARM:
      if(millis()%1000<500)
        sprintf(displayBuffer, "SET ALAR");
      else
        sprintf(displayBuffer, "ET ALARM");
        if(millis()-mode_start>2000) // wait 2s to set alarm
          currentState++;
      break;
    case SET_ALARM_ENABLED:
      if(alarm.enabled)
        sprintf(displayBuffer,"   ON   ");
      else
        sprintf(displayBuffer,"   OFF  ");
      break;
    case SET_ALARM_HOUR:
      if(tick)
        sprintf(displayBuffer, set_hour_tick, alarm.minute);
      else
        sprintf(displayBuffer, set_hour_no_tick, alarm.hour, alarm.minute);
      break;
    case SET_ALARM_MINUTE:
      if(tick)
        sprintf(displayBuffer, set_minute_tick, alarm.hour);
      else
        sprintf(displayBuffer, set_minute_no_tick, alarm.hour, alarm.minute);
      break;
    case SET_TIME:
      sprintf(displayBuffer,"SET TIME");
      if(millis()-mode_start>2000) // wait 2s to set time
        currentState++;
      break;   
    case SET_HOUR:
      if(tick)
        sprintf(displayBuffer, set_hour_tick, curDateTime.minute);
      else
        sprintf(displayBuffer, set_hour_no_tick, curDateTime.hour, curDateTime.minute);
      break;
    case SET_MINUTE:
      if(tick)
        sprintf(displayBuffer, set_minute_tick, curDateTime.hour);
      else
        sprintf(displayBuffer, set_minute_no_tick, curDateTime.hour, curDateTime.minute);
      break;
    case SET_DATE:
      sprintf(displayBuffer,"SET DATE");
      if(millis()-mode_start>2000) // wait 2s to set date
        currentState++;
      break;
    case SET_MONTH:
      if(tick)
        sprintf(displayBuffer, set_month_tick, curDateTime.monthDay);
      else
        printDate();
      break;
    case SET_DAY:
      if(tick)
        sprintf(displayBuffer, set_day_tick, month[curDateTime.month-1]);
      else
        printDate();
      break;
    case SET_YEAR:
      if(tick)
        sprintf(displayBuffer, "        ");
      else
        sprintf(displayBuffer, set_year_tick, curDateTime.year);
      break;
    case WRITE_DATETIME:
      setDateTime();
      currentState=CLOCK;
      break;
    case WRITE_ALARM:
      setAlarmSettings();
      currentState=CLOCK;
      break;
  }
}
 
void shiftBits (byte cathodes, byte segments1,  byte segments2){
  PORTD |= B10000000; // HC595s latch high
  for (int k=0; k < 8; k++){
    PORTB &= ~1; // HC595s clock low
    if ( cathodes & (0b10000000 >> k) )
      PORTD |= 0b100000; // HC595-1 data high
    else
      PORTD &= ~0b100000; // HC595-1 data low
    if ( segments2 & (0b10000000 >> k) )
      PORTD |= 0b10000; // HC595-2 data high
    else
      PORTD &= ~0b10000; // HC595-2 data low
    if ( segments1 & (0b10000000 >> k) )
      PORTD |= 0b1000000; // HC595-3 data high
    else
      PORTD &= ~0b1000000; // HC595-3 data low
    PORTB |= 1; // HC595s clock high
  }
  PORTD &= ~0b10000000; // HC595s latch low
}
 
void displayISR(){  
  PORTD &= ~B1000; // HC595s output enabled
  for (int cathode = 0; cathode <8; cathode++){
    shiftBits(0xFF-(1<<cathode),pgm_read_byte(&ascii[(2*(displayBuffer[cathode]-0x20))]), pgm_read_byte(&ascii[(1+2*(displayBuffer[cathode]-0x20))]));
  }
  PORTD |= B1000; // HC595s output disabled
}
 
byte bcdToDec(byte val) {
  return ((val/16*10)+(val%16));
}
 
byte decToBcd(byte val){
  return ((val/10*16)+(val%10));
}
 
void updateCurDateTime() {
  static unsigned long last_update = -200;
  if((currentState<SET_HOUR || currentState>SET_MINUTE) && currentState != WRITE_DATETIME) {
    if(millis()-last_update>100) {
      Timer1.detachInterrupt(); // disable display ISR while using i2c bus 
      Wire.beginTransmission(DS1307_ADDRESS);
      WireWrite(0);
      Wire.endTransmission();
      Wire.requestFrom(DS1307_ADDRESS, 7);
      curDateTime.second = bcdToDec(WireRead);
      curDateTime.minute = bcdToDec(WireRead);
      curDateTime.hour = bcdToDec(WireRead & 0b111111);
      curDateTime.weekDay = bcdToDec(WireRead);
      if(currentState>SET_DAY || currentState<SET_YEAR) {
        curDateTime.monthDay = bcdToDec(WireRead);
        curDateTime.month = bcdToDec(WireRead);
        curDateTime.year = bcdToDec(WireRead)+2000;
      }
      if(curDateTime.second & 0b1000000) {
        curDateTime.second = 0; // disable Clock Halt bit on fresh ds1307 chip
        setDateTime();
      }
      Timer1.attachInterrupt(displayISR);
    }
  }
}
 
void setDateTime() {
  Timer1.detachInterrupt();
  Wire.beginTransmission(DS1307_ADDRESS);
  WireWrite(0); 
  WireWrite(decToBcd(curDateTime.second));
  WireWrite(decToBcd(curDateTime.minute));
  WireWrite(decToBcd(curDateTime.hour));
  WireWrite(decToBcd(curDateTime.weekDay));
  WireWrite(decToBcd(curDateTime.monthDay));
  WireWrite(decToBcd(curDateTime.month));
  WireWrite(decToBcd(curDateTime.year-2000));
  WireWrite(0); 
  Wire.endTransmission();
  Timer1.attachInterrupt(displayISR);
}
 
void getAlarmSettings()
{
  if(EEPROM.read(0)==0x13 && EEPROM.read(1)==0x37) // check signature
  {
    alarm.enabled = EEPROM.read(2);
    alarm.hour = EEPROM.read(3);
    alarm.minute = EEPROM.read(4);
  }
  digitalWrite(alarmLed, alarm.enabled);
}
 
void setAlarmSettings()
{
  EEPROM.write(0, 0x13);
  EEPROM.write(1, 0x37);
  EEPROM.write(2, alarm.enabled);
  EEPROM.write(3, alarm.hour);
  EEPROM.write(4, alarm.minute);
}