Last active
April 24, 2022 23:48
-
-
Save gonzopancho/8a3de550f1d86403a6735d15dd3a9eb8 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| MMC Device 0 not found [198/1444] | |
| no mmc device at slot 0 | |
| switch to partitions #0, OK | |
| mmc1 is current device | |
| Scanning mmc 1:1... | |
| Found EFI removable media binary efi/boot/bootaa64.efi | |
| libfdt fdt_check_header(): FDT_ERR_BADMAGIC | |
| Scanning disk mmc@7e300000.blk... | |
| Found 3 disks | |
| FDT memrsv map 0: Failed to add to map | |
| BootOrder not defined | |
| 637384 bytes read in 50 ms (12.2 MiB/s) | |
| libfdt fdt_check_header(): FDT_ERR_BADMAGIC | |
| FDT memrsv map 0: Failed to add to map | |
| ## Starting EFI application at 00080000 ... | |
| Consoles: EFI console | |
| FreeBSD/arm64 EFI loader, Revision 1.1 | |
| Command line arguments: loader.efi | |
| EFI version: 2.70 | |
| EFI Firmware: Das U-Boot (rev 8217.1024) | |
| Console: efi (0) | |
| Load Path: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,0x01,0,0x1,0x19000)/efi\boot\bootaa64.efi | |
| Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,0x01,0,0x1,0x19000) | |
| Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,0x01,0,0x1,0x19000) | |
| Setting currdev to disk0p1: | |
| Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(2,0x01,0,0x19001,0x2cb418) | |
| Setting currdev to disk0p2: | |
| Loading /boot/defaults/loader.conf | |
| Loading /boot/device.hints | |
| Loading /boot/loader.conf | |
| Loading /boot/loader.conf.local | |
| / | |
| \ __ | |
| _ __ / _|___ ___ _ __ ___ ___ | |
| | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ | |
| | |_) | _\__ \ __/ | | \__ \ __/ | |
| | .__/|_| |___/\___|_| |_|___/\___| | |
| |_| | |
| ╔═══════════Welcome to pfSense════════════╗ __________________________ | |
| ║ ║ / ___\ | |
| ║ 1. Boot Multi user [Enter] ║ | /` | |
| ║ 2. Boot Single user ║ | / :-| | |
| ║ 3. Escape to loader prompt ║ | _________ ___/ /_ | | |
| ║ 4. Reboot ║ | /` ____ / /__ ___/ | | |
| ║ ║ | / / / / / / | | |
| ║ Options: ║ | / /___/ / / / | | |
| ║ 5. Kernel: default/kernel (1 of 1) ║ | / ______/ / / | | |
| ║ 6. Boot Options ║ |/ / / / | | |
| ║ ║ / /___/ | | |
| ║ ║ / | | |
| ║ ║ /_________________________/ | |
| ╚═════════════════════════════════════════╝ | | |
| Autoboot in 0 seconds, hit [Enter] to boot or any other key to stop | |
| Loading kernel... | |
| /boot/kernel/kernel text=0xb3177d data=0x966c40+0x79e48c syms=[0x8+0x14cb50+0x8+0x12072e] | |
| Loading configured modules... | |
| can't find '/boot/entropy' | |
| Using DTB provided by EFI at 0x7ef6000. | |
| EFI framebuffer information: | |
| addr, size 0x3eaf0000, 0x10a800 | |
| dimensions 656 x 416 | |
| stride 656 | |
| masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000 ---<<BOOT>>--- | |
| Copyright (c) 1992-2018 The FreeBSD Project. | |
| Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 | |
| The Regents of the University of California. All rights reserved. | |
| FreeBSD is a registered trademark of The FreeBSD Foundation. | |
| FreeBSD 12.0-RELEASE-p4 5531562acbb(factory-RELENG_2_5) pfSense arm64 | |
| FreeBSD clang version 6.0.1 (tags/RELEASE_601/final 335540) (based on LLVM 6.0.1) | |
| VT(efifb): resolution 656x416 | |
| Starting CPU 1 (1) | |
| Starting CPU 2 (2) | |
| Starting CPU 3 (3) | |
| FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs | |
| arc4random: no preloaded entropy cache | |
| random: entropy device external interface | |
| ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. | |
| ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. | |
| module_register_init: MOD_LOAD (ipw_bss_fw, 0xffff00000020ad60, 0) error 1 | |
| ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. | |
| ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. | |
| module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffff00000020ae0c, 0) error 1 | |
| ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. | |
| ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. | |
| module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffff00000020aeb8, 0) error 1 | |
| iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. | |
| iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. | |
| module_register_init: MOD_LOAD (iwi_bss_fw, 0xffff00000020af64, 0) error 1 | |
| iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. | |
| iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. | |
| module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffff00000020b010, 0) error 1 | |
| iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. | |
| iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. | |
| module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffff00000020b0bc, 0) error 1 | |
| wlan: mac acl policy registered | |
| MAP 7ef6000 mode 2 pages 20 | |
| MAP 39f4d000 mode 2 pages 1 | |
| MAP 39f52000 mode 2 pages 1 | |
| MAP 3b350000 mode 2 pages 16 | |
| MAP 3f100000 mode 1 pages 1 | |
| [ath_hal] loaded | |
| kbd0 at kbdmux0 | |
| ofwbus0: <Open Firmware Device Tree> | |
| simplebus0: <Flattened device tree simple bus> on ofwbus0 | |
| ofw_clkbus0: <OFW clocks bus> on ofwbus0 | |
| clk_fixed0: <Fixed clock> on ofw_clkbus0 | |
| clk_fixed1: <Fixed clock> on ofw_clkbus0 | |
| regfix0: <Fixed Regulator> on ofwbus0 | |
| regfix1: <Fixed Regulator> on ofwbus0 | |
| psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 | |
| local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on simplebus0 | |
| intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq 20 on simplebus0 | |
| gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 23,24 on simplebus0 | |
| gpiobus0: <OFW GPIO bus> on gpio0 | |
| generic_timer0: <ARMv7 Generic Timer> irq 0,1,2,3 on ofwbus0 | |
| Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000 | |
| Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000 | |
| bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq 4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19 on simplebus0 | |
| bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100027 on simplebus0 | |
| bcmrng0: <Broadcom BCM2835 RNG> mem 0x7e104000-0x7e10400f irq 21 on simplebus0 | |
| mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 22 on simplebus0 | |
| gpioc0: <GPIO controller> on gpio0 | |
| uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e201fff irq 25 on simplebus0 | |
| uart0: console (115200,n,8,1) | |
| spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e204fff irq 27 on simplebus0 | |
| spibus0: <OFW SPI bus> on spi0 | |
| spibus0: <unknown card> at cs 0 mode 0 | |
| spibus0: <unknown card> at cs 1 mode 0 [66/1444] | |
| iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 40 on simplebus0 | |
| bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 46,47 on simplebus0 | |
| usbus0 on bcm283x_dwcotg0 | |
| sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 49 on simplebus0 | |
| mmc0: <MMC/SD bus> on sdhci_bcm0 | |
| fb0: <BCM2835 VT framebuffer driver> on simplebus0 | |
| fbd0 on fb0 | |
| VT: Replacing driver "efifb" with new "fb". | |
| fb0: 656x416(656x416@0,0) 24bpp | |
| fb0: fbswap: 1, pitch 1968, base 0x3eb33000, screen_size 818688 | |
| pmu0: <Performance Monitoring Unit> irq 53 on simplebus0 | |
| cpulist0: <Open Firmware CPU Group> on ofwbus0 | |
| cpu0: <Open Firmware CPU> on cpulist0 | |
| bcm2835_cpufreq0: <CPU Frequency Control> on cpu0 | |
| cpu1: <Open Firmware CPU> on cpulist0 | |
| cpu2: <Open Firmware CPU> on cpulist0 | |
| cpu3: <Open Firmware CPU> on cpulist0 | |
| gpioled0: <GPIO LEDs> on ofwbus0 | |
| gpioled0: <led1> failed to map pin | |
| cryptosoft0: <software crypto> | |
| Timecounters tick every 1.000 msec | |
| usbus0: 480Mbps High Speed USB v2.0 | |
| iicbus0: <OFW I2C bus> on iichb0 | |
| iic0: <I2C generic I/O> on iicbus0 | |
| ugen0.1: <DWCOTG OTG Root HUB> at usbus0 | |
| uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 | |
| mmcsd0: 16GB <SDHC SB16G 8.0 SN A4B62AA6 MFG 09/2017 by 3 SD> at mmc0 50.0MHz/4bit/65535-block | |
| mbox0: mbox response error | |
| bcm2835_cpufreq0: can't get clock rate (id=8) | |
| bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM -999MHz, Turbo OFF | |
| uhub0: 1 port with 1 removable, self powered | |
| ugen0.2: <vendor 0x0424 product 0x2514> at usbus0 | |
| uhub1 on uhub0 | |
| uhub1: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/b.b3, addr 2> on usbus0 | |
| uhub1: MTT enabled | |
| uhub1: 4 ports with 3 removable, self powered | |
| ugen0.3: <vendor 0x0424 product 0x2514> at usbus0 | |
| uhub2 on uhub1 | |
| uhub2: <vendor 0x0424 product 0x2514, class 9/0, rev 2.00/b.b3, addr 3> on usbus0 | |
| uhub2: MTT enabled | |
| uhub2: 3 ports with 2 removable, self powered | |
| ugen0.4: <vendor 0x0424 product 0x7800> at usbus0 | |
| muge0 on uhub2 | |
| muge0: <vendor 0x0424 product 0x7800, rev 2.10/3.00, addr 4> on usbus0 | |
| muge0: Chip ID 0x7800 rev 0002 | |
| miibus0: <MII bus> on muge0 | |
| ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 | |
| ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto | |
| ue0: <USB Ethernet> on muge0 | |
| ue0: Ethernet address: b8:27:eb:22:4d:e0 | |
| Release APs...random: unblocking device. | |
| done | |
| arc4random: no preloaded entropy cache | |
| CPU 0: ARM Cortex-A53 r0p4 affinity: 0 | |
| Trying to mount root from ufs:/dev/ufsid/5d0100a80a9ad292 [rw,noatime]... | |
| Instruction Set Attributes 0 = <CRC32> | |
| arc4random: no preloaded entropy cache | |
| Instruction Set Attributes 1 = <> | |
| arc4random: no preloaded entropy cache | |
| Processor Features 0 = <AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32> | |
| Processor Features 1 = <0> | |
| Memory Model Features 0 = <4k Granule,64k Granule,MixedEndian,S/NS Mem,16bit ASID,1TB PA> | |
| Warning: no time-of-day clock registered, Memory Model Features 1 = <> | |
| system time will not be set accurately | |
| Memory Model Features 2 = <32b CCIDX,48b VA> | |
| Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6 Breakpoints,PMUv3,Debug v8> | |
| Debug Features 1 = <0> | |
| Auxiliary Features 0 = <0> | |
| Auxiliary Features 1 = <0> | |
| CPU 1: ARM Cortex-A53 r0p4 affinity: 1 | |
| CPU 2: ARM Cortex-A53 r0p4 affinity: 2 | |
| CPU 3: ARM Cortex-A53 r0p4 affinity: 3 | |
| Configuring crash dumps... | |
| dumpon: /dev/label/swap*: No such file or directory | |
| Unable to specify /dev/label/swap* as a dump device. | |
| No suitable dump device was found. | |
| Growing root partition to fill device | |
| mmcsd0s2 resized | |
| gpart: Operation not permitted | |
| super-block backups (for fsck_ffs -b #) at: | |
| 2930112, 3662592, 4395072, 5127552, 5860032, 6592512, 7324992, 8057472, | |
| 8789952, 9522432, 10254912, 10987392, 11719872, 12452352, 13184832, 13917312, | |
| 14649792, 15382272, 16114752, 16847232, 17579712, 18312192, 19044672, | |
| 19777152, 20509632, 21242112, 21974592, 22707072, 23439552, 24172032, | |
| 24904512, 25636992, 26369472, 27101952, 27834432, 28566912, 29299392, | |
| 30031872, 30764352 | |
| /dev/ufsid/5d0100a80a9ad292: FILE SYSTEM CLEAN; SKIPPING CHECKS | |
| /dev/ufsid/5d0100a80a9ad292: clean, 3446003 free (435 frags, 430696 blocks, 0.0% fragmentation) | |
| Filesystems are clean, continuing... | |
| Mounting filesystems... | |
| __ | |
| _ __ / _|___ ___ _ __ ___ ___ | |
| | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ | |
| | |_) | _\__ \ __/ | | \__ \ __/ | |
| | .__/|_| |___/\___|_| |_|___/\___| | |
| |_| | |
| Welcome to pfSense 2.5.0-DEVELOPMENT... | |
| ...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/ipsec /usr/local/lib/perl5/5.28/mach/CORE | |
| done. | |
| Can't open /etc/thoth/device.der for reading, No such file or directory | |
| 1076854784:error:02001002:system library:fopen:No such file or directory:/usr/home/luiz/git/crossbuild/pfSense/tmp/FreeBSD-src/crypto/openssl/crypto/bio/bss_file.c:72:fopen('/etc/thoth/device.der','rb') | |
| 1076854784:error:2006D080:BIO routines:BIO_new_file:no such file:/usr/home/luiz/git/crossbuild/pfSense/tmp/FreeBSD-src/crypto/openssl/crypto/bio/bss_file.c:79: | |
| unable to load certificate | |
| chown: /etc/thoth/key.pem: No such file or directory | |
| chmod: /etc/thoth/key.pem: No such file or directory | |
| External config loader 1.0 is now starting... mmcsd0s1 mmcsd0s2 | |
| Launching the init system......... done. | |
| Initializing.................. done. | |
| Starting device manager (devd)...done. | |
| Loading configuration......done. | |
| Updating configuration.............. | |
| Warning: Invalid argument supplied for foreach() in /etc/inc/xmlparse.inc on line 235 | |
| ...done. | |
| Warning: Configuration references interfaces that do not exist: em0 em1 | |
| Network interface mismatch -- Running interface assignment option. | |
| muge0: Chip ID 0x7800 rev 0002 | |
| ue0: link state changed to DOWN | |
| Valid interfaces are: | |
| ue0 b8:27:eb:22:4d:e0 (down) USB Ethernet | |
| Do VLANs need to be set up first? | |
| If VLANs will not be used, or only for optional interfaces, it is typical to | |
| say no here and use the webConfigurator to configure VLANs later, if required. | |
| Should VLANs be set up now [y|n]? ue0: link state changed to UP | |
Hi, how do you build pfsense source code, I have many troubles how to compile source code. Thank you for answer M.
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Hows this working out for you? :) It would be very nice to use a Pi as a failover/high availability pfsense router. Or even if the performance is slow, just a temporary one while having downtime on primary router.