Skip to content

Instantly share code, notes, and snippets.

@heitbaum
Last active August 11, 2021 07:04
Show Gist options
  • Save heitbaum/e4dceeb7b236560b94cc66fce91cdd11 to your computer and use it in GitHub Desktop.
Save heitbaum/e4dceeb7b236560b94cc66fce91cdd11 to your computer and use it in GitHub Desktop.
[238]HELLO! BOOT0 is starting!
[241]BOOT0 commit : 27369ab
[243]set pll start
[245]periph0 has been enabled
[248]set pll end
[250][pmu]: bus read error
[252]board init ok
[254]DRAM only have internal ZQ!!
[257]get_pmu_exist() = -1
[260]ddr_efuse_type: 0x0
[263][AUTO DEBUG] two rank and full DQ!
[267]ddr_efuse_type: 0x0
[270][AUTO DEBUG] rank 0 row = 15
[273][AUTO DEBUG] rank 0 bank = 8
[276][AUTO DEBUG] rank 0 page size = 2 KB
[280][AUTO DEBUG] rank 1 row = 15
[283][AUTO DEBUG] rank 1 bank = 8
[286][AUTO DEBUG] rank 1 page size = 2 KB
[290]rank1 config same as rank0
[293]DRAM BOOT DRIVE INFO: V0.24
[296]DRAM CLK = 792 MHz
[298]DRAM Type = 3 (2:DDR2,3:DDR3)
[301]DRAMC ZQ value: 0x7b7bfb
[304]DRAM ODT value: 0x42.
[307]ddr_efuse_type: 0x0
[310]DRAM SIZE =1024 M
[313]DRAM simple test OK.
[316]dram size =1024
[318]card no is 0
[319]sdcard 0 line count 4
[322][mmc]: mmc driver ver 2021-04-2 16:45
[331][mmc]: Wrong media type 0x0
[334][mmc]: ***Try SD card 0***
[355][mmc]: HSSDR52/SDR25 4 bit
[358][mmc]: 50000000 Hz
[360][mmc]: 30436 MB
[362][mmc]: ***SD/MMC 0 init OK!!!***
[412]Loading boot-pkg Succeed(index=0).
[416]Entry_name = opensbi
[419]Entry_name = u-boot
[422]Entry_name = dtb
[425]mmc not para
[427]Jump to second Boot.
OpenSBI v0.6
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x40000400
Firmware Size : 75 KB
Runtime SBI Version : 0.2
MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000040000000-0x000000004001ffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3 : 0x0000000000020000-0x0000000000027fff (A,▒
U-Boot 2018.05-g0a88ac9-dirty-config-dirty (Jun 16 2021 - 02:06:53 +0000) Allwinner Technology
[00.511]DRAM: 1 GiB
[00.513]Relocation Offset is: 3dee4000
[00.517]secure enable bit: 0
[00.520]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.526]flash init start
[00.528]workmode = 0,storage type = 1
[00.532][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1
[00.537][mmc]: get sdc_type fail and use default host:tm1.
[00.544][mmc]: can't find node "mmc0",will add new node
[00.548][mmc]: fdt err returned <no error>
[00.552][mmc]: Using default timing para
[00.556][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.584][mmc]: card_caps:0x3000000a
[00.587][mmc]: host_caps:0x3000003f
[00.592]sunxi flash init ok
[00.595]line:714 init_clocks
[00.605]drv_disp_init
[00.622]drv_disp_init finish
[00.624]boot_gui_init:start
[00.627]set disp.dev2_output_type fail. using defval=0
[00.819]boot_gui_init:finish
[01.178]bmp_name=bootlogo.bmp size 3072054
[01.231]LCD open finish
[01.320]show bmp on fb failed !-1
[01.330]Loading Environment from SUNXI_FLASH... OK
[01.350]out of usb burn from boot: not need burn key
[01.360]update part info
[01.363]update bootcmd
[01.366]change working_fdt 0x7eaa3da8 to 0x7ea83da8
[01.388]update dts
[01.949]
[01.952][mmc]: MMC Device 2 not found
[01.955][mmc]: mmc 2 not find, so not exit
__clk_init: clk pll_periph0x2 already initialized
register fix_factor clk error
request pwm success, pwm2:pwm2:0x2000c00.
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
3072054 bytes read in 129 ms (22.7 MiB/s)
no support big size bmp[800x1280] on fb[1280x720]
root_partition is rootfs
set root to /dev/mmcblk0p5
Hit any key to stop autoboot: 0
card0 has inited
curr_device:0
Device: SUNXI SD/MMC
Manufacturer ID: 3
OEM: 5344
Name: SD32G
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 29.7 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x0000a1f8 0x0000b9bd "boot-resource"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: a0085546-4166-744a-a353-fca9272b8e45
2 0x0000b9be 0x0000bbb5 "env"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: a0085546-4166-744a-a353-fca9272b8e46
3 0x0000bbb6 0x0000bdad "env-redund"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: a0085546-4166-744a-a353-fca9272b8e47
4 0x0000c000 0x0003d7ff ""
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: bc5b1e95-0008-443f-9493-835a7bf25548
5 0x0003ddae 0x00a3ddad "rootfs"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: a0085546-4166-744a-a353-fca9272b8e49
6 0x00a3ddae 0x03b723dd "UDISK"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: a0085546-4166-744a-a353-fca9272b8e4a
223 bytes read in 1 ms (217.8 KiB/s)
287 bytes read in 2 ms (139.6 KiB/s)
9588736 bytes read in 400 ms (22.9 MiB/s)
Android's image name: d1-nezha
No reserved memory region found in source FDT
Starting kernel ...
Welcome to Debian GNU/Linux 11 (bullseye)!
[ OK ] Created slice system-getty.slice.
[ OK ] Created slice system-modprobe.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice User and Session Slice.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ OK ] Reached target Remote File Systems.
[ OK ] Reached target Slices.
[ OK ] Reached target Swap.
[ OK ] Listening on Syslog Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Listening on udev Kernel Socket.
Mounting Kernel Debug File System...
Starting Load Kernel Module configfs...
Starting Load Kernel Module drm...
Starting Load Kernel Module fuse...
Starting File System Check on Root Device...
Starting Journal Service...
Starting Load Kernel Modules...
Starting Coldplug All udev Devices...
[ OK ] Mounted Kernel Debug File System.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
Mounting Kernel Configuration File System...
[ OK ] Started File System Check Daemon to report status.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Load Kernel Modules.
Starting Apply Kernel Variables...
[ OK ] Finished File System Check on Root Device.
Starting Remount Root and Kernel File Systems...
[ OK ] Finished Apply Kernel Variables.
[ OK ] Finished Remount Root and Kernel File Systems.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
Starting Load/Save Random Seed...
Starting Create System Users...
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Tell Plymouth To Write Out Runtime Data...
Starting Create Volatile Files and Directories...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Finished Tell Plymouth To Write Out Runtime Data.
[ OK ] Finished Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Finished Coldplug All udev Devices.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Started Rule-based Manager for Device Events and Files.
Starting Show Plymouth Boot Screen...
[ OK ] Started Show Plymouth Boot Screen.
[ OK ] Started Forward Password R…s to Plymouth Directory Watch.
[ OK ] Reached target Local Encrypted Volumes.
[ OK ] Reached target Paths.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target System Time Set.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Trigger anacron every hour.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Daily exim4-base housekeeping.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily man-db regeneration.
[ OK ] Reached target Timers.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started Run anacron jobs.
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Connection service...
Starting DUN service...
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting Telephony service...
Starting Authorization Manager...
Starting System Logging Service...
Starting User Login Management...
Starting Disk Manager...
Starting WPA supplicant...
[ OK ] Found device /dev/ttyS0.
[ OK ] Started System Logging Service.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started DUN service.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Started Telephony service.
[ OK ] Started WPA supplicant.
[ OK ] Started Authorization Manager.
[ OK ] Started Connection service.
[ OK ] Started User Login Management.
[ OK ] Started Disk Manager.
[ OK ] Reached target Hardware activated USB gadget.
[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
Starting Modem Manager...
Starting Save/Restore Sound Card State...
Starting Wait for network to be configured by ConnMan...
Starting Load/Save RF Kill Switch Status...
[ OK ] Started Load/Save RF Kill Switch Status.
[ OK ] Finished Save/Restore Sound Card State.
[ OK ] Reached target Sound Card.
[ OK ] Started Modem Manager.
Starting Hostname Service...
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ OK ] Finished Helper to synchronize boot up for ifupdown.
[ OK ] Started ifup for eth0.
Starting Raise network interfaces...
[ OK ] Started Hostname Service.
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Finished Wait for network to be configured by ConnMan.
[ OK ] Finished Raise network interfaces.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
Starting LSB: exim Mail Transport Agent...
Starting /etc/rc.local Compatibility...
Starting OpenBSD Secure Shell server...
Starting Permit User Sessions...
[ OK ] Finished Permit User Sessions.
Starting Light Display Manager...
Debian GNU/Linux 11 RVBoards ttyS0
RVBoards login: root
Password:
Linux RVBoards 5.4.61 #22 PREEMPT Wed Jun 16 07:27:49 UTC 2021 riscv64
root@RVBoards:~# parted
GNU Parted 3.4
Using /dev/mmcblk0
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) p
Model: SD SD32G (sd/mmc)
Disk /dev/mmcblk0: 31.9GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 21.2MB 24.3MB 3116kB boot-resource msftdata
2 24.3MB 24.6MB 258kB env msftdata
3 24.6MB 24.9MB 258kB env-redund msftdata
4 25.2MB 129MB 104MB fat16 msftdata
5 130MB 5498MB 5369MB ext4 rootfs msftdata
6 5498MB 31.9GB 26.4GB UDISK msftdata
[ 0.105369] sunxi-msgbox-amp 3003000.msgbox: invalid resource
[ 0.250781] uart uart0: get regulator failed
[ 0.263848] uart uart1: get regulator failed
[ 0.269565] uart uart4: get regulator failed
[ 0.276672] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[ 0.284011] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[ 0.297838] Failed to alloc md5
[ 0.472708] sunxi_get_str_of_property()1560 - failed to get the string of propname led_regulator!
[ 0.483514] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 0.491182] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 0.503312] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.510896] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.518506] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 0.526126] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
root@RVBoards:~# dmesg
[ 0.532852] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 0.534980] mmcblk0: mmc0:e624 SD32G 29.7 GiB
[ 0.537405] sunxi-daudio 2034000.daudio: regulator missing or invalid
[ 0.538437] [AUDIOCODEC][sunxi_codec_parse_params][2094]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1
[ 0.538452] [AUDIOCODEC][sunxi_codec_parse_params][2130]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[ 0.540671] [AUDIOCODEC][sunxi_internal_codec_probe][2266]:codec probe finished
[ 0.542066] mmcblk0: p1 p2 p3 p4 p5 p6
[ 0.544619] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[ 0.554568] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device disconnect
[ 0.554593] sunxi-ohci 4200400.ohci1-controller: ohci_irq: fullspeed or lowspeed device connect
[ 0.554761] [SNDCODEC][sunxi_card_init][583]:card init finished
[ 0.557020] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[ 0.558351] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1
[ 0.559015] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished
[ 0.559728] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: register device finished!
[ 0.559739] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: [rpaf_dsp0] probe finished!
[ 0.560119] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102!
[ 0.560287] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed
[ 0.562053] NET: Registered protocol family 10
[ 0.563479] Segment Routing with IPv6
[ 0.563665] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 0.564423] NET: Registered protocol family 17
[ 0.564493] can: controller area network core (rev 20170425 abi 9)
[ 0.564586] NET: Registered protocol family 29
[ 0.564598] can: raw protocol (rev 20170425)
[ 0.564603] can: broadcast manager protocol (rev 20170425 t)
[ 0.564616] can: netlink gateway (rev 20190810) max_hops=1
[ 0.564918] Bluetooth: RFCOMM TTY layer initialized
[ 0.564937] Bluetooth: RFCOMM socket layer initialized
[ 0.564966] Bluetooth: RFCOMM ver 1.11
[ 0.565924] Loading compiled-in X.509 certificates
[ 0.568218] HDMI 2.0 driver init start!
[ 0.568245] boot_hdmi=false
[ 0.568308] ERROR: pinctrl_get for HDMI2.0 DDC fail
[ 0.575454] HDMI2.0 module init end
[ 0.598785] twi twi2: twi2 supply twi not found, using dummy regulator
[ 0.606862] pcf857x 2-0038: probed
[ 0.613117] sunxi_i2c_probe()2262 - [i2c2] probe success
[ 0.617550] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present!
[ 0.627722] sunxi-audio-card 2031060.sounddmic: dmic-hifi <-> 2031000.dmic mapping ok
[ 0.629101] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present!
[ 0.639861] sunxi-audio-card 20340a0.sounddaudio2: 20340a4.hdmiaudio <-> 2034000.daudio mapping ok
[ 0.641236] get ehci0-controller wakeup-source is fail.
[ 0.641349] sunxi ehci0-controller don't init wakeup source
[ 0.641363] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe00090f498, 0x:ffffffd005343000, irq_no:2e
[ 0.641367] [sunxi-ehci0]: Not init ehci0
[ 0.641842] get ohci0-controller wakeup-source is fail.
[ 0.641972] sunxi ohci0-controller don't init wakeup source
[ 0.641983] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe00090ffd8
[ 0.641988] [sunxi-ohci0]: Not init ohci0
[ 0.644227] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 0.646451] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 0.646595] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 0.646604] cfg80211: failed to load regulatory.db
[ 0.646728] clk: Not disabling unused clocks
[ 0.646741] ALSA device list:
[ 0.646748] #0: audiocodec
[ 0.646752] #1: snddmic
[ 0.646756] #2: sndhdmi
[ 0.646771] alloc_fd: slot 0 not NULL!
[ 0.658652] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ 0.658717] VFS: Mounted root (ext4 filesystem) readonly on device 179:5.
[ 0.666075] devtmpfs: mounted
[ 0.666253] Freeing unused kernel memory: 184K
[ 0.666257] This architecture does not have kernel memory protection.
[ 0.666262] Run /sbin/init as init process
[ 0.991055] HDMI cable is connected
[ 1.031069] usb 2-1: new low-speed USB device number 2 using sunxi-ohci
[ 1.154622] random: fast init done
[ 1.246143] systemd[1]: Failed to look up module alias 'autofs4': Function not implemented
[ 1.260993] cgroup2: Unknown parameter 'memory_recursiveprot'
[ 1.288367] systemd[1]: systemd 247.3-5 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 1.288718] systemd[1]: Detected architecture riscv64.
[ 1.312973] input: Microsoft Wired Keyboard 600 as /devices/platform/soc@3000000/4200400.ohci1-controller/usb2/2-1/2-1:1.0/0003:045E:07F8.0001/input/input2
[ 1.328987] systemd[1]: Set hostname to <RVBoards>.
[ 1.382155] hid-generic 0003:045E:07F8.0001: input: USB HID v1.11 Keyboard [Microsoft Wired Keyboard 600] on usb-sunxi-ohci-1/input0
[ 1.388072] input: Microsoft Wired Keyboard 600 Consumer Control as /devices/platform/soc@3000000/4200400.ohci1-controller/usb2/2-1/2-1:1.1/0003:045E:07F8.0002/input/input3
[ 1.451532] input: Microsoft Wired Keyboard 600 System Control as /devices/platform/soc@3000000/4200400.ohci1-controller/usb2/2-1/2-1:1.1/0003:045E:07F8.0002/input/input4
[ 1.451777] hid-generic 0003:045E:07F8.0002: input: USB HID v1.11 Device [Microsoft Wired Keyboard 600] on usb-sunxi-ohci-1/input1
[ 1.911273] error: invalid cea_vic code:0
[ 1.911280] [HDMI2 error]: sink do not support this mode:0
[ 2.706957] systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed.
[ 2.988975] systemd[1]: Queued start job for default target Multi-User System.
[ 2.991575] random: systemd: uninitialized urandom read (16 bytes read)
[ 2.991965] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[ 2.991998] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[ 2.993411] systemd[1]: Created slice system-getty.slice.
[ 3.021298] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.022409] systemd[1]: Created slice system-modprobe.slice.
[ 3.051312] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.052403] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 3.082076] systemd[1]: Created slice User and Session Slice.
[ 3.111823] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.141722] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 3.142459] systemd[1]: Reached target Remote File Systems.
[ 3.171473] systemd[1]: Reached target Slices.
[ 3.201513] systemd[1]: Reached target Swap.
[ 3.233408] systemd[1]: Listening on Syslog Socket.
[ 3.262211] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 3.291846] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 3.347872] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 3.348982] systemd[1]: Listening on Journal Socket (/dev/log).
[ 3.382523] systemd[1]: Listening on Journal Socket.
[ 3.412647] systemd[1]: Listening on udev Control Socket.
[ 3.442196] systemd[1]: Listening on udev Kernel Socket.
[ 3.472063] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 3.472828] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped.
[ 3.476830] systemd[1]: Mounting Kernel Debug File System...
[ 3.501925] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 3.503378] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped.
[ 3.507849] systemd[1]: Starting Load Kernel Module configfs...
[ 3.526699] systemd[1]: Starting Load Kernel Module drm...
[ 3.559840] systemd[1]: Starting Load Kernel Module fuse...
[ 3.594333] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 3.598447] systemd[1]: Starting File System Check on Root Device...
[ 3.635418] systemd[1]: Starting Journal Service...
[ 3.663876] systemd[1]: Starting Load Kernel Modules...
[ 3.683297] systemd[1]: Starting Coldplug All udev Devices...
[ 3.772878] systemd[1]: Mounted Kernel Debug File System.
[ 3.783771] systemd[1]: modprobe@configfs.service: Succeeded.
[ 3.801420] systemd[1]: Finished Load Kernel Module configfs.
[ 3.849952] systemd[1]: modprobe@drm.service: Succeeded.
[ 3.860356] systemd[1]: Finished Load Kernel Module drm.
[ 3.864058] systemd[1]: modprobe@fuse.service: Succeeded.
[ 3.892032] systemd[1]: Finished Load Kernel Module fuse.
[ 3.899703] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 3.921677] systemd[1]: Mounting Kernel Configuration File System...
[ 3.957204] systemd[1]: Started File System Check Daemon to report status.
[ 4.026302] systemd[1]: Mounted Kernel Configuration File System.
[ 4.073234] systemd[1]: Finished Load Kernel Modules.
[ 4.080170] systemd[1]: Starting Apply Kernel Variables...
[ 4.115419] systemd[1]: Finished File System Check on Root Device.
[ 4.145676] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 4.423923] systemd[1]: Finished Apply Kernel Variables.
[ 4.492207] EXT4-fs (mmcblk0p5): re-mounted. Opts: (null)
[ 4.512167] systemd[1]: Started Journal Service.
[ 4.892038] systemd-journald[100]: Received client request to flush runtime journal.
[ 6.353508] proc: Bad value for 'hidepid'
[ 9.757714] proc: Bad value for 'hidepid'
[ 15.294319] sunxi-rfkill soc@3000000:rfkill@0: set block: 0
[ 15.331247] sunxi-rfkill soc@3000000:rfkill@0: bt power on success
[ 16.059105] proc: Bad value for 'hidepid'
[ 16.183768] libphy: 4500000.eth: probed
[ 16.194662] sunxi-gmac 4500000.eth eth0: eth0: Type(8) PHY ID 001cc916 at 0 IRQ poll (4500000.eth-0:00)
[ 16.290212] sunxi-rfkill soc@3000000:rfkill@0: block state already is 0
[ 20.401384] sunxi-gmac 4500000.eth eth0: Link is Up - 1Gbps/Full - flow control off
[ 20.401413] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 26.581103] random: crng init done
[ 26.581115] random: 7 urandom warning(s) missed due to ratelimiting
[ 35.340656] usb1-vbus: disabling
[ 41.649909] ======== XRADIO WIFI OPEN ========
[ 41.656770] [XRADIO] Driver Label:XR_V02.16.84_P2P_HT40_01.31
[ 41.665610] [XRADIO] Allocated hw_priv @ 00000000e44ca6b1
[ 41.678938] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1
[ 41.691260] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success
[ 41.896860] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 41.896971] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 41.896995] [XRADIO] Detect SDIO card 1
[ 41.909539] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 41.920511] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 41.923611] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 41.938544] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 41.938644] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 41.938787] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[ 41.939733] mmc1: new high speed SDIO card at address 0001
[ 41.942272] [SBUS] XRadio Device:sdio clk=50000000
[ 41.980030] [XRADIO] XRADIO_HW_REV 1.0 detected.
[ 42.040488] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000.
[ 42.082727] [XRADIO] Bootloader complete
[ 42.181956] [XRADIO] Firmware completed.
[ 42.198345] [WSM] Firmware Label:XR_C09.08.52.64_DBG_02.100 2GHZ HT40 Jan 3 2020 13:14:37
[ 42.216416] [XRADIO] Firmware Startup Done.
[ 42.221732] [XRADIO_WRN] enable Multi-Rx!
[ 42.252933] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 42.472389] fuse: init (API version 7.31)
[ 42.644541] ieee80211_do_open: vif_type=2, p2p=0, ch=3, addr=38:48:12:38:15:be
[ 42.693099] [STA] !!!xradio_vif_setup: id=0, type=2, p2p=0, addr=38:48:12:38:15:be
[ 42.766227] [AP_WRN] BSS_CHANGED_ASSOC but driver is unjoined.
[ 43.091944] ieee80211_do_open: vif_type=10, p2p=0, ch=3, addr=38:48:12:38:15:bf
[ 43.100195] [STA] !!!xradio_vif_setup: id=2, type=10, p2p=0, addr=38:48:12:38:15:bf
[ 43.196821] xt_time: kernel timezone is -0000
[ 43.296140] usbcore: registered new interface driver uvcvideo
[ 43.296148] USB Video Class driver (1.1.1)
[ 43.491180] ieee80211_do_open: vif_type=10, p2p=0, ch=3, addr=38:48:12:38:95:bf
[ 43.499438] [STA] !!!xradio_vif_setup: id=1, type=10, p2p=0, addr=38:48:12:38:95:bf
[ 43.525742] disp 0, type 4, mode5
[ 44.555815] [HDMI receive params]: tv mode: 0x5 format:0x1 data bits:0x0 eotf:0x4 cs:0x101 dvi_hdmi:2 range:2 scan:0 aspect_ratio:8
[ 45.649063] disp_al_manager_apply ouput_type:0
[ 45.649790] disp_al_hdmi_cfg
[ 45.764526] HDMI Audio Enable Successfully
[ 45.764541] [DISP] disp_device_attached_and_enable,line:233:
[ 45.764546] attached ok, mgr0<-->dev0
[ 45.764550] [DISP] disp_device_attached_and_enable,line:236:
[ 45.764559] type:4,mode:5,fmt:yuv444,bits:8bits,eotf:4,cs:257 dvi_hdmi:2, range:2 scan:0 ratio:8
[ 48.374537] HDMI cable is disconnected
[ 48.891639] HDMI cable is connected
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment