Buffalo WHR-300HP2 captured boot sequence. baud rate was 57600.

WHR-300HP2_boot.txt

U-Boot 1.1.3 (Apr  3 2013 - 20:22:35)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
*** Check if data is correct or not...
*** Data is correct.
============================================
Ralink UBoot Version: 4.1.1.0
Buffalo UBoot Version: 3.00
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr  3 2013  Time:20:22:35
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
 0
aossgpio=[8192]

3: System Boot system code via Flash.
raspi_read: from:30000 len:10000
Erasing SPI Flash...
raspi_erase: offs:30000 len:10000
.
Writing to SPI Flash...
raspi_write: to:30000 len:10000
.
done
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5180075 Bytes =  4.9 MB
   Load Address: 80000000
   Entry Point:  8000c310
raspi_read: from:50040 len:4f0aab
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (root@SWD1-CVS3) (gcc version 3.4.2) #17 Thu May 2 10:13:33 CST 2013

 The CPU feqenuce set to 580 MHz
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00000008
Readback ErrCtl register=00000008
Memory: 56052k/65536k available (4316k kernel code, 9484k reserved, 807k data, 3572k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1a311c
RALINK_GPIOMODE = 18311c
PPLL_CFG1=0xe80000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
PCIE0 no card, disable it(RST&CLK)
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 109
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
#####GPIOMODE = 18111d#####
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
flash0: started
deice id : ef 40 17 0 0 (40170000)
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000600000 : "Kernel"
0x000000600000-0x000000700000 : "User_CFG"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24


=== pAd = c0156000, size = 808880 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.5
Ralink APSoC Hardware Watchdog Timer
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (875 buckets, 3500 max)
ctnetlink v0.93: registering with nfnetlink.
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 3572k freed
init started: BusyBox v1.12.1 (2013-Algorithmics/MIPS FPU Emulator v1.5
05-02 10:06:23 CST)
starting pid 28, tty '': '/etc_ro/rcS'
led=9, on=1, off=1, blinks,=4000, reset=1, time=4000
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
    _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=

[check_jffs]80 : JFFS_OK
Set: phy[0].reg[0] = 3100
Set: phy[1].reg[0] = 3100
Set: phy[2].reg[0] = 3100
Set: phy[3].reg[0] = 3100
Set: phy[4].reg[0] = 3100
nvram_init: INFO=>nvram MAC initialized successfully!
==>shm_init()!!
check_shm_hash: Check shm hash value
hashNum are the same with WIFITxRate1, -1718058408!!!
nvram_init: INFO=>nvram conf initialized successfully!
nvram_init: INFO=> RAM CONF successful created!
nvram_init: INFO=> RC.CONF successful created!
---------------- Get WLAN MAC b0:c7:45:ad:bf:48---------------
switch reg write offset=94, value=1000
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg writeRaeth v3.0 ( oTaskletff)
set=2
phy_tx_ring = 0x0248d000, tx_ring = 0xa248d000

phy_rx_ring0 = 0x0248e000, rx_ring0 = 0xa248e000
SMACCR1 -- : 0x0000b0c7
SMACCR0 -- : 0x45adbf48
01CDMA_CSG_CFG = 81000000
4,GDMA1_FWD_CFG = 20710000
 value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
device vlan0001 entered promiscuous mode
device eth2 entered promiscuous mode
input_access=[3]
echo 3 > /proc/lan_wlan_access_controller
br0: port 1(vlan0001) entering learning state
br0: port 1(vlan0001) entering learning state
led=58, on=4000, off=1, blinks,=1, reset=1, time=4000
led=57, on=1, off=1, blinks,=4000, reset=1, time=4000
getbootloaderenv : bootloader_ver =3.00
br0: port 1(vlan0001) entering forwarding state
Fri Jan  1 00:00:00 GMT 2010
rmmod: ipv6passthru: No such file or directory
rmmod: ipv6passthru: No such file or directory
/usr/shell/dnsmasq.sh stop ok
dnsmasq: read /tmp/iphost - 1 addresses
dnsmasq: [truncated] m
/usr/shell/dnsmasq.sh start ok
/usr/shell/udhcpd.sh config ok
/usr/shell/udhcpd.sh start ok

***** g_wl_interface = ra0 ******

MAX_NUM_SESSIONS : 5; NUM_SEES: 64
[Enter Test] in wlan_led_ctrl.c main()
.brctl setwlanforward br0 15
libupnp: using UDP SSDP_PORT = 1900
killall: pptpd: no process killed
starting pid 4808, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2013-05-02 10:06:23 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# help

Built-in commands:
-------------------
        . : break cd chdir continue eval exec exit export false hash
        help let local pwd read readonly return set shift source times
        trap true type ulimit umask unset wait

# pwd
/
# ls
proc    mnt     dev     media   sbin    var     bin     usr
sys     etc     init    home    lib     www     tmp     etc_ro
# cat /proc/cpuinfo
system type             : Ralink SoC
processor               : 0
cpu model               : MIPS 24Kc V5.0
BogoMIPS                : 386.04
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0ff8, 0x0ff8, 0x0ae3, 0x0ff8]
ASEs implemented        : mips16 dsp
shadow register sets    : 1
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available


---------------------------------------
u-boot Entr boot command line interface
---------------------------------------

MT7620 # printenv
bootcmd=tftp
bootdelay=1
baudrate=57600
ethaddr="00:AA:BB:CC:DD:10"
filesize=408bee
fileaddr=80A00000
ipaddr=192.168.11.1
serverip=192.168.11.168
autostart=no
bootfile=firmware_WHR-300HP2.ram
inspection=0
bootloader_ver=3.00
stdin=serial
stdout=serial
stderr=serial
pushaoss=0

Environment size: 277/4092 bytes