Skip to content

Instantly share code, notes, and snippets.

@hnyman

hnyman/R7800_TFTP_flash_and_boot_log.txt

Created December 3, 2019 20:48
Show Gist options
  • Save hnyman/9f0ef6434aa01420bf8087186040ae17 to your computer and use it in GitHub Desktop.
Save hnyman/9f0ef6434aa01420bf8087186040ae17 to your computer and use it in GitHub Desktop.
Download ZIP
R7800 TFTP flashing and boot process log
Raw
R7800_TFTP_flash_and_boot_log.txt
U-Boot 2012.07 [local,local] (Sep 03 2015 - 17:33:28)
U-boot 2012.07 dni1 V0.4 for DNI HW ID: 29764958 NOR flash 0MB; NAND flash 128MB; RAM 512MB; 1st Radio 4x4; 2nd Radio 4x4; Cascade
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:
*** Warning - bad CRC, using default environment
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
131072 bytes read: OK
MMC Device 0 not found
cdp: get part failed for 0:HLOS
Net: MAC1 addr:dc:ef:9:ef:f3:e6
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:dc:ef:9:ef:f3:e5
eth0, eth1
Factory Reset Mode
The Router is in TFTP Server Firmware Recovery mode NOW!
Listening on Port : 69, IP Address: 192.168.1.1 ...
Upgrade Mode Upgrade Mode
Rcv:
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.................................................................
.....................................................
Done!
Bytes transferred = 12583041 (c00081 hex)
MODEL ID on image: R7800
Firmware Image MODEL ID do not match open source firmware ID
131072 bytes read: OK
HW ID on board: 29764958+0+128+512+4x4+4x4+cascade
HW ID on image: 29764958+0+128+512+4x4+4x4+cascade
Firmware Image HW ID matched Board HW ID
131072 bytes read: OK
MODEL ID on board: R7800
MODEL ID on image: R7800
Firmware Image MODEL ID matched Board model ID
131072 bytes read: OK
MODEL ID on board: R7800
MODEL ID on image: R7800
Firmware Image MODEL ID matched Board model ID
Erasing: off 1480000, size 20000
Erasing at 0x1480000 -- 100% complete. Cleanmarker written at 0x1480000.
OK
Writing: from RAM addr 42000080, to NAND off 1480000, size 20000
131072 bytes written: OK
Alive-timer 26
NmrpAliveTimerBase 15
Erasing: off 14a0000, size 20000
Erasing at 0x14a0000 -- 100% complete. Cleanmarker written at 0x14a0000.
OK
Writing: from RAM addr 42020080, to NAND off 14a0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 14c0000, size 20000
Erasing at 0x14c0000 -- 100% complete. Cleanmarker written at 0x14c0000.
OK
Writing: from RAM addr 42040080, to NAND off 14c0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 14e0000, size 20000
Erasing at 0x14e0000 -- 100% complete. Cleanmarker written at 0x14e0000.
OK
Writing: from RAM addr 42060080, to NAND off 14e0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1500000, size 20000
Erasing at 0x1500000 -- 100% complete. Cleanmarker written at 0x1500000.
OK
Writing: from RAM addr 42080080, to NAND off 1500000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1520000, size 20000
Erasing at 0x1520000 -- 100% complete. Cleanmarker written at 0x1520000.
OK
Writing: from RAM addr 420a0080, to NAND off 1520000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1540000, size 20000
Erasing at 0x1540000 -- 100% complete. Cleanmarker written at 0x1540000.
OK
Writing: from RAM addr 420c0080, to NAND off 1540000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1560000, size 20000
Erasing at 0x1560000 -- 100% complete. Cleanmarker written at 0x1560000.
OK
Writing: from RAM addr 420e0080, to NAND off 1560000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1580000, size 20000
Erasing at 0x1580000 -- 100% complete. Cleanmarker written at 0x1580000.
OK
Writing: from RAM addr 42100080, to NAND off 1580000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 15a0000, size 20000
Erasing at 0x15a0000 -- 100% complete. Cleanmarker written at 0x15a0000.
OK
Writing: from RAM addr 42120080, to NAND off 15a0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 15c0000, size 20000
Erasing at 0x15c0000 -- 100% complete. Cleanmarker written at 0x15c0000.
OK
Writing: from RAM addr 42140080, to NAND off 15c0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 15e0000, size 20000
Erasing at 0x15e0000 -- 100% complete. Cleanmarker written at 0x15e0000.
OK
Writing: from RAM addr 42160080, to NAND off 15e0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1600000, size 20000
Erasing at 0x1600000 -- 100% complete. Cleanmarker written at 0x1600000.
OK
Writing: from RAM addr 42180080, to NAND off 1600000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1620000, size 20000
Erasing at 0x1620000 -- 100% complete. Cleanmarker written at 0x1620000.
OK
Writing: from RAM addr 421a0080, to NAND off 1620000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1640000, size 20000
Erasing at 0x1640000 -- 100% complete. Cleanmarker written at 0x1640000.
OK
Writing: from RAM addr 421c0080, to NAND off 1640000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1660000, size 20000
Erasing at 0x1660000 -- 100% complete. Cleanmarker written at 0x1660000.
OK
Writing: from RAM addr 421e0080, to NAND off 1660000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1680000, size 20000
Erasing at 0x1680000 -- 100% complete. Cleanmarker written at 0x1680000.
OK
Writing: from RAM addr 42200080, to NAND off 1680000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 16a0000, size 20000
Erasing at 0x16a0000 -- 100% complete. Cleanmarker written at 0x16a0000.
OK
Writing: from RAM addr 42220080, to NAND off 16a0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 16c0000, size 20000
Erasing at 0x16c0000 -- 100% complete. Cleanmarker written at 0x16c0000.
OK
Writing: from RAM addr 42240080, to NAND off 16c0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 16e0000, size 20000
Erasing at 0x16e0000 -- 100% complete. Cleanmarker written at 0x16e0000.
OK
Writing: from RAM addr 42260080, to NAND off 16e0000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1700000, size 20000
Erasing at 0x1700000 -- 100% complete. Cleanmarker written at 0x1700000.
OK
Writing: from RAM addr 42280080, to NAND off 1700000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1720000, size 20000
Erasing at 0x1720000 -- 100% complete. Cleanmarker written at 0x1720000.
OK
Writing: from RAM addr 422a0080, to NAND off 1720000, size 20000
131072 bytes written: OK
Alive-timer 15
Erasing: off 1740000, size 20000
Erasing at 0x1740000 -- 100% complete. Cleanmarker written at 0x1740000.
OK
Writing: from RAM addr 422c0080, to NAND off 1740000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1760000, size 20000
Erasing at 0x1760000 -- 100% complete. Cleanmarker written at 0x1760000.
OK
Writing: from RAM addr 422e0080, to NAND off 1760000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1780000, size 20000
Erasing at 0x1780000 -- 100% complete. Cleanmarker written at 0x1780000.
OK
Writing: from RAM addr 42300080, to NAND off 1780000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 17a0000, size 20000
Erasing at 0x17a0000 -- 100% complete. Cleanmarker written at 0x17a0000.
OK
Writing: from RAM addr 42320080, to NAND off 17a0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 17c0000, size 20000
Erasing at 0x17c0000 -- 100% complete. Cleanmarker written at 0x17c0000.
OK
Writing: from RAM addr 42340080, to NAND off 17c0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 17e0000, size 20000
Erasing at 0x17e0000 -- 100% complete. Cleanmarker written at 0x17e0000.
OK
Writing: from RAM addr 42360080, to NAND off 17e0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1800000, size 20000
Erasing at 0x1800000 -- 100% complete. Cleanmarker written at 0x1800000.
OK
Writing: from RAM addr 42380080, to NAND off 1800000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1820000, size 20000
Erasing at 0x1820000 -- 100% complete. Cleanmarker written at 0x1820000.
OK
Writing: from RAM addr 423a0080, to NAND off 1820000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1840000, size 20000
Erasing at 0x1840000 -- 100% complete. Cleanmarker written at 0x1840000.
OK
Writing: from RAM addr 423c0080, to NAND off 1840000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1860000, size 20000
Erasing at 0x1860000 -- 100% complete. Cleanmarker written at 0x1860000.
OK
Writing: from RAM addr 423e0080, to NAND off 1860000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1880000, size 20000
Erasing at 0x1880000 -- 100% complete. Cleanmarker written at 0x1880000.
OK
Writing: from RAM addr 42400080, to NAND off 1880000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 18a0000, size 20000
Erasing at 0x18a0000 -- 100% complete. Cleanmarker written at 0x18a0000.
OK
Writing: from RAM addr 42420080, to NAND off 18a0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 18c0000, size 20000
Erasing at 0x18c0000 -- 100% complete. Cleanmarker written at 0x18c0000.
OK
Writing: from RAM addr 42440080, to NAND off 18c0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 18e0000, size 20000
Erasing at 0x18e0000 -- 100% complete. Cleanmarker written at 0x18e0000.
OK
Writing: from RAM addr 42460080, to NAND off 18e0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1900000, size 20000
Erasing at 0x1900000 -- 100% complete. Cleanmarker written at 0x1900000.
OK
Writing: from RAM addr 42480080, to NAND off 1900000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1920000, size 20000
Erasing at 0x1920000 -- 100% complete. Cleanmarker written at 0x1920000.
OK
Writing: from RAM addr 424a0080, to NAND off 1920000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1940000, size 20000
Erasing at 0x1940000 -- 100% complete. Cleanmarker written at 0x1940000.
OK
Writing: from RAM addr 424c0080, to NAND off 1940000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1960000, size 20000
Erasing at 0x1960000 -- 100% complete. Cleanmarker written at 0x1960000.
OK
Writing: from RAM addr 424e0080, to NAND off 1960000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 1980000, size 20000
Erasing at 0x1980000 -- 100% complete. Cleanmarker written at 0x1980000.
OK
Writing: from RAM addr 42500080, to NAND off 1980000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 19a0000, size 20000
Erasing at 0x19a0000 -- 100% complete. Cleanmarker written at 0x19a0000.
OK
Writing: from RAM addr 42520080, to NAND off 19a0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 19c0000, size 20000
Erasing at 0x19c0000 -- 100% complete. Cleanmarker written at 0x19c0000.
OK
Writing: from RAM addr 42540080, to NAND off 19c0000, size 20000
131072 bytes written: OK
Alive-timer 16
Erasing: off 19e0000, size 20000
Erasing at 0x19e0000 -- 100% complete. Cleanmarker written at 0x19e0000.
OK
Writing: from RAM addr 42560080, to NAND off 19e0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1a00000, size 20000
Erasing at 0x1a00000 -- 100% complete. Cleanmarker written at 0x1a00000.
OK
Writing: from RAM addr 42580080, to NAND off 1a00000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1a20000, size 20000
Erasing at 0x1a20000 -- 100% complete. Cleanmarker written at 0x1a20000.
OK
Writing: from RAM addr 425a0080, to NAND off 1a20000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1a40000, size 20000
Erasing at 0x1a40000 -- 100% complete. Cleanmarker written at 0x1a40000.
OK
Writing: from RAM addr 425c0080, to NAND off 1a40000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1a60000, size 20000
Erasing at 0x1a60000 -- 100% complete. Cleanmarker written at 0x1a60000.
OK
Writing: from RAM addr 425e0080, to NAND off 1a60000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1a80000, size 20000
Erasing at 0x1a80000 -- 100% complete. Cleanmarker written at 0x1a80000.
OK
Writing: from RAM addr 42600080, to NAND off 1a80000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1aa0000, size 20000
Erasing at 0x1aa0000 -- 100% complete. Cleanmarker written at 0x1aa0000.
OK
Writing: from RAM addr 42620080, to NAND off 1aa0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1ac0000, size 20000
Erasing at 0x1ac0000 -- 100% complete. Cleanmarker written at 0x1ac0000.
OK
Writing: from RAM addr 42640080, to NAND off 1ac0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1ae0000, size 20000
Erasing at 0x1ae0000 -- 100% complete. Cleanmarker written at 0x1ae0000.
OK
Writing: from RAM addr 42660080, to NAND off 1ae0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1b00000, size 20000
Erasing at 0x1b00000 -- 100% complete. Cleanmarker written at 0x1b00000.
OK
Writing: from RAM addr 42680080, to NAND off 1b00000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1b20000, size 20000
Erasing at 0x1b20000 -- 100% complete. Cleanmarker written at 0x1b20000.
OK
Writing: from RAM addr 426a0080, to NAND off 1b20000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1b40000, size 20000
Erasing at 0x1b40000 -- 100% complete. Cleanmarker written at 0x1b40000.
OK
Writing: from RAM addr 426c0080, to NAND off 1b40000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1b60000, size 20000
Erasing at 0x1b60000 -- 100% complete. Cleanmarker written at 0x1b60000.
OK
Writing: from RAM addr 426e0080, to NAND off 1b60000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1b80000, size 20000
Erasing at 0x1b80000 -- 100% complete. Cleanmarker written at 0x1b80000.
OK
Writing: from RAM addr 42700080, to NAND off 1b80000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1ba0000, size 20000
Erasing at 0x1ba0000 -- 100% complete. Cleanmarker written at 0x1ba0000.
OK
Writing: from RAM addr 42720080, to NAND off 1ba0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1bc0000, size 20000
Erasing at 0x1bc0000 -- 100% complete. Cleanmarker written at 0x1bc0000.
OK
Writing: from RAM addr 42740080, to NAND off 1bc0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1be0000, size 20000
Erasing at 0x1be0000 -- 100% complete. Cleanmarker written at 0x1be0000.
OK
Writing: from RAM addr 42760080, to NAND off 1be0000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1c00000, size 20000
Erasing at 0x1c00000 -- 100% complete. Cleanmarker written at 0x1c00000.
OK
Writing: from RAM addr 42780080, to NAND off 1c00000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1c20000, size 20000
Erasing at 0x1c20000 -- 100% complete. Cleanmarker written at 0x1c20000.
OK
Writing: from RAM addr 427a0080, to NAND off 1c20000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1c40000, size 20000
Erasing at 0x1c40000 -- 100% complete. Cleanmarker written at 0x1c40000.
OK
Writing: from RAM addr 427c0080, to NAND off 1c40000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1c60000, size 20000
Erasing at 0x1c60000 -- 100% complete. Cleanmarker written at 0x1c60000.
OK
Writing: from RAM addr 427e0080, to NAND off 1c60000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1c80000, size 20000
Erasing at 0x1c80000 -- 100% complete. Cleanmarker written at 0x1c80000.
OK
Writing: from RAM addr 42800080, to NAND off 1c80000, size 20000
131072 bytes written: OK
Alive-timer 17
Erasing: off 1ca0000, size 20000
Erasing at 0x1ca0000 -- 100% complete. Cleanmarker written at 0x1ca0000.
OK
Writing: from RAM addr 42820080, to NAND off 1ca0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1cc0000, size 20000
Erasing at 0x1cc0000 -- 100% complete. Cleanmarker written at 0x1cc0000.
OK
Writing: from RAM addr 42840080, to NAND off 1cc0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1ce0000, size 20000
Erasing at 0x1ce0000 -- 100% complete. Cleanmarker written at 0x1ce0000.
OK
Writing: from RAM addr 42860080, to NAND off 1ce0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1d00000, size 20000
Erasing at 0x1d00000 -- 100% complete. Cleanmarker written at 0x1d00000.
OK
Writing: from RAM addr 42880080, to NAND off 1d00000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1d20000, size 20000
Erasing at 0x1d20000 -- 100% complete. Cleanmarker written at 0x1d20000.
OK
Writing: from RAM addr 428a0080, to NAND off 1d20000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1d40000, size 20000
Erasing at 0x1d40000 -- 100% complete. Cleanmarker written at 0x1d40000.
OK
Writing: from RAM addr 428c0080, to NAND off 1d40000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1d60000, size 20000
Erasing at 0x1d60000 -- 100% complete. Cleanmarker written at 0x1d60000.
OK
Writing: from RAM addr 428e0080, to NAND off 1d60000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1d80000, size 20000
Erasing at 0x1d80000 -- 100% complete. Cleanmarker written at 0x1d80000.
OK
Writing: from RAM addr 42900080, to NAND off 1d80000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1da0000, size 20000
Erasing at 0x1da0000 -- 100% complete. Cleanmarker written at 0x1da0000.
OK
Writing: from RAM addr 42920080, to NAND off 1da0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1dc0000, size 20000
Erasing at 0x1dc0000 -- 100% complete. Cleanmarker written at 0x1dc0000.
OK
Writing: from RAM addr 42940080, to NAND off 1dc0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1de0000, size 20000
Erasing at 0x1de0000 -- 100% complete. Cleanmarker written at 0x1de0000.
OK
Writing: from RAM addr 42960080, to NAND off 1de0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1e00000, size 20000
Erasing at 0x1e00000 -- 100% complete. Cleanmarker written at 0x1e00000.
OK
Writing: from RAM addr 42980080, to NAND off 1e00000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1e20000, size 20000
Erasing at 0x1e20000 -- 100% complete. Cleanmarker written at 0x1e20000.
OK
Writing: from RAM addr 429a0080, to NAND off 1e20000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1e40000, size 20000
Erasing at 0x1e40000 -- 100% complete. Cleanmarker written at 0x1e40000.
OK
Writing: from RAM addr 429c0080, to NAND off 1e40000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1e60000, size 20000
Erasing at 0x1e60000 -- 100% complete. Cleanmarker written at 0x1e60000.
OK
Writing: from RAM addr 429e0080, to NAND off 1e60000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1e80000, size 20000
Erasing at 0x1e80000 -- 100% complete. Cleanmarker written at 0x1e80000.
OK
Writing: from RAM addr 42a00080, to NAND off 1e80000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1ea0000, size 20000
Erasing at 0x1ea0000 -- 100% complete. Cleanmarker written at 0x1ea0000.
OK
Writing: from RAM addr 42a20080, to NAND off 1ea0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1ec0000, size 20000
Erasing at 0x1ec0000 -- 100% complete. Cleanmarker written at 0x1ec0000.
OK
Writing: from RAM addr 42a40080, to NAND off 1ec0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1ee0000, size 20000
Erasing at 0x1ee0000 -- 100% complete. Cleanmarker written at 0x1ee0000.
OK
Writing: from RAM addr 42a60080, to NAND off 1ee0000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1f00000, size 20000
Erasing at 0x1f00000 -- 100% complete. Cleanmarker written at 0x1f00000.
OK
Writing: from RAM addr 42a80080, to NAND off 1f00000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1f20000, size 20000
Erasing at 0x1f20000 -- 100% complete. Cleanmarker written at 0x1f20000.
OK
Writing: from RAM addr 42aa0080, to NAND off 1f20000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1f40000, size 20000
Erasing at 0x1f40000 -- 100% complete. Cleanmarker written at 0x1f40000.
OK
Writing: from RAM addr 42ac0080, to NAND off 1f40000, size 20000
131072 bytes written: OK
Alive-timer 18
Erasing: off 1f60000, size 20000
Erasing at 0x1f60000 -- 100% complete. Cleanmarker written at 0x1f60000.
OK
Writing: from RAM addr 42ae0080, to NAND off 1f60000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 1f80000, size 20000
Erasing at 0x1f80000 -- 100% complete. Cleanmarker written at 0x1f80000.
OK
Writing: from RAM addr 42b00080, to NAND off 1f80000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 1fa0000, size 20000
Erasing at 0x1fa0000 -- 100% complete. Cleanmarker written at 0x1fa0000.
OK
Writing: from RAM addr 42b20080, to NAND off 1fa0000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 1fc0000, size 20000
Erasing at 0x1fc0000 -- 100% complete. Cleanmarker written at 0x1fc0000.
OK
Writing: from RAM addr 42b40080, to NAND off 1fc0000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 1fe0000, size 20000
Erasing at 0x1fe0000 -- 100% complete. Cleanmarker written at 0x1fe0000.
OK
Writing: from RAM addr 42b60080, to NAND off 1fe0000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 2000000, size 20000
Erasing at 0x2000000 -- 100% complete. Cleanmarker written at 0x2000000.
OK
Writing: from RAM addr 42b80080, to NAND off 2000000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 2020000, size 20000
Erasing at 0x2020000 -- 100% complete. Cleanmarker written at 0x2020000.
OK
Writing: from RAM addr 42ba0080, to NAND off 2020000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 2040000, size 20000
Erasing at 0x2040000 -- 100% complete. Cleanmarker written at 0x2040000.
OK
Writing: from RAM addr 42bc0080, to NAND off 2040000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 2060000, size 20000
Erasing at 0x2060000 -- 100% complete. Cleanmarker written at 0x2060000.
OK
Writing: from RAM addr 42be0080, to NAND off 2060000, size 20000
131072 bytes written: OK
Alive-timer 19
Erasing: off 2080000, size 20000
Erasing at 0x2080000 -- 100% complete. Cleanmarker written at 0x2080000.
OK
Writing: from RAM addr 42c00080, to NAND off 2080000, size 20000
131072 bytes written: OK
Alive-timer 19
Done
Rebooting...
resetting ...
Resetting with watch dog!
U-Boot 2012.07 [local,local] (Sep 03 2015 - 17:33:28)
U-boot 2012.07 dni1 V0.4 for DNI HW ID: 29764958 NOR flash 0MB; NAND flash 128MB; RAM 512MB; 1st Radio 4x4; 2nd Radio 4x4; Cascade
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Unsupported manufacturer 00
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
MMC:
*** Warning - bad CRC, using default environment
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
131072 bytes read: OK
MMC Device 0 not found
cdp: get part failed for 0:HLOS
Net: MAC1 addr:dc:ef:9:ef:f3:e6
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:dc:ef:9:ef:f3:e5
eth0, eth1
Hit any key to stop autoboot: 2  1  0
Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual
nmrp server is stopped or failed !
Loading from device 0: nand0 (offset 0x1480000)
** check kernel image **
Verifying Checksum ... OK
** check rootfs image **
Verifying Checksum ... OK
MMC Device 0 not found
Loading from nand0, offset 0x1480000
Image Name: ARM OpenWrt Linux-4.19.86
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2482758 Bytes = 2.4 MiB
Load Address: 42208000
Entry Point: 42208000
Automatic boot of image at addr 0x44000000 ...
Image Name: ARM OpenWrt Linux-4.19.86
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2482758 Bytes = 2.4 MiB
Load Address: 42208000
Entry Point: 42208000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
mtdparts variable not set, see 'help mtdparts'
no partitions defined
defaults:
mtdids : nand0=msm_nand
mtdparts: none
info: "mtdparts" not set
Using machid 0x136c from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.86 (perus@ub1910) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r11569-482114d3f7)) #0 SMP Tue Dec 3 17:28:43 2019
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x80/0x47c with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu s29964 r8192 d23284 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800
[ 0.000000] Kernel command line:
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 475884K/491520K available (5289K kernel code, 180K rwdata, 1364K rodata, 1024K init, 228K bss, 15636K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (6282 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 181 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 229 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000007] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000023] Switching to timer-based delay loop, resolution 160ns
[ 0.000241] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000267] pid_max: default: 32768 minimum: 301
[ 0.000449] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000467] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001371] CPU: Testing write buffer coherency: ok
[ 0.002510] Setting up static identity map for 0x42300000 - 0x42300060
[ 0.002694] rcu: Hierarchical SRCU implementation.
[ 0.003540] smp: Bringing up secondary CPUs ...
[ 0.005487] smp: Brought up 1 node, 2 CPUs
[ 0.005505] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.005515] CPU: All CPU(s) started in SVC mode.
[ 0.017066] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.017228] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017258] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.017425] pinctrl core: initialized pinctrl subsystem
[ 0.018591] NET: Registered protocol family 16
[ 0.018866] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.020294] cpuidle: using governor ladder
[ 0.020364] cpuidle: using governor menu
[ 0.044247] usbcore: registered new interface driver usbfs
[ 0.044328] usbcore: registered new interface driver hub
[ 0.044416] usbcore: registered new device driver usb
[ 0.044476] pps_core: LinuxPPS API ver. 1 registered
[ 0.044491] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.044526] PTP clock support registered
[ 0.046187] clocksource: Switched to clocksource dg_timer
[ 0.049525] NET: Registered protocol family 2
[ 0.050111] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.050150] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.050190] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.050244] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.050339] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.050373] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.050604] NET: Registered protocol family 1
[ 0.052077] No memory allocated for crashlog
[ 0.052346] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.058879] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.058896] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.068146] io scheduler noop registered
[ 0.068167] io scheduler deadline registered (default)
[ 0.070140] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator
[ 0.070270] qcom-pcie 1b500000.pci: Linked as a consumer to regulator.0
[ 0.070299] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.070422] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.070696] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges:
[ 0.070755] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.070789] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.291420] qcom-pcie 1b500000.pci: Link up
[ 0.291584] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.291608] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.291630] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.291645] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.295813] PCI: bus0: Fast back to back transfers disabled
[ 0.301889] PCI: bus1: Fast back to back transfers disabled
[ 0.301996] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.302023] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.302152] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.302178] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.302804] pcieport 0000:00:00.0: AER enabled with IRQ 36
[ 0.303325] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator
[ 0.303443] qcom-pcie 1b700000.pci: Linked as a consumer to regulator.0
[ 0.303470] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.303588] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.303870] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges:
[ 0.303926] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.303955] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.533716] qcom-pcie 1b700000.pci: Link up
[ 0.533867] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.533890] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.533907] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.538040] PCI: bus0: Fast back to back transfers disabled
[ 0.540230] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 0.544123] PCI: bus1: Fast back to back transfers disabled
[ 0.544217] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.544243] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.544375] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.544396] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.544938] pcieport 0001:00:00.0: AER enabled with IRQ 38
[ 0.547475] L2 @ QSB rate. Forcing new rate.
[ 0.547699] L2 @ 384000 KHz
[ 0.547886] CPU0 @ 800000 KHz
[ 0.547900] CPU1 @ QSB rate. Forcing new rate.
[ 0.548032] CPU1 @ 384000 KHz
[ 0.551733] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.553876] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.554665] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.554724] msm_serial 16340000.serial: uartclk = 7372800
[ 0.554794] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM
[ 0.554837] msm_serial: console setup on port #0
[ 1.308610] console [ttyMSM0] enabled
[ 1.313587] msm_serial: driver initialized
[ 1.322229] loop: module loaded
[ 1.324192] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1
[ 1.324227] nand: Micron MT29F1G08ABBEAH4
[ 1.330899] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.334784] 8 fixed-partitions partitions found on MTD device qcom_nand.0
[ 1.342234] Creating 8 MTD partitions on "qcom_nand.0":
[ 1.349086] 0x000000000000-0x000000c80000 : "qcadata"
[ 1.359255] random: fast init done
[ 1.375323] 0x000000c80000-0x000001180000 : "APPSBL"
[ 1.384324] 0x000001180000-0x000001200000 : "APPSBLENV"
[ 1.386021] 0x000001200000-0x000001340000 : "art"
[ 1.391263] 0x000001340000-0x000001480000 : "artbak"
[ 1.396073] 0x000001480000-0x000001880000 : "kernel"
[ 1.405603] 0x000001880000-0x000007900000 : "ubi"
[ 1.563524] 0x000007900000-0x000008000000 : "reserve"
[ 1.577087] libphy: GPIO Bitbanged MDIO: probed
[ 1.598476] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.459560] ar8327: qca,phy-rgmii-en is not specified
[ 2.459962] libphy: Fixed MDIO Bus: probed
[ 2.465748] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock
[ 2.468413] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 2.474112] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000
[ 2.481678] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported
[ 2.487469] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported
[ 2.495111] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2
[ 2.503084] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported
[ 2.508894] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported
[ 2.516204] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors
[ 2.523045] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors
[ 2.530607] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled
[ 2.537636] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.545415] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock
[ 2.552830] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[ 2.558848] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000
[ 2.566202] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported
[ 2.572094] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported
[ 2.579810] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2
[ 2.587713] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported
[ 2.593460] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported
[ 2.600927] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors
[ 2.607715] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors
[ 2.615162] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled
[ 2.622264] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 2.629197] i2c /dev entries driver
[ 2.637966] Calibration not found.
[ 2.641968] Speed bin: 0
[ 2.643717] PVS bin: 4
[ 2.649016] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.649234] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.656813] sdhci: Secure Digital Host Controller Interface driver
[ 2.663078] sdhci: Copyright(c) Pierre Ossman
[ 2.669409] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.677353] NET: Registered protocol family 10
[ 2.681819] Segment Routing with IPv6
[ 2.683878] NET: Registered protocol family 17
[ 2.687915] 8021q: 802.1Q VLAN Support v1.8
[ 2.691861] Registering SWP/SWPB emulation handler
[ 2.723457] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364
[ 2.739299] s1a: supplied by regulator-dummy
[ 2.739462] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.743103] s1b: supplied by regulator-dummy
[ 2.747802] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.752268] s2a: supplied by regulator-dummy
[ 2.756987] s2a: Bringing 0uV into 775000-775000uV
[ 2.761449] s2b: supplied by regulator-dummy
[ 2.765761] s2b: Bringing 0uV into 775000-775000uV
[ 2.772620] cpu cpu0: Linked as a consumer to regulator.4
[ 2.774799] cpu cpu0: Dropping the link to regulator.4
[ 2.780573] cpu cpu0: Linked as a consumer to regulator.4
[ 2.785858] cpu cpu1: Linked as a consumer to regulator.5
[ 2.792347] UBI: auto-attach mtd6
[ 2.796034] ubi0: attaching mtd6
[ 2.873619] UBI: EOF marker found, PEBs from 59 will be erased
[ 2.881770] random: crng init done
[ 2.971976] ubi0: scanning is finished
[ 2.996124] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 691 LEBs
[ 2.996610] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[ 3.001531] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.007082] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.013772] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.020691] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[ 3.027472] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 3.033652] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1575394123
[ 3.040748] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[ 3.050235] ubi0: background thread "ubi_bgt0d" started, PID 62
[ 3.077004] block ubiblock0_0: created from ubi0:0(rootfs)
[ 3.077025] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 3.081376] hctosys: unable to open rtc device (rtc0)
[ 3.408423] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 3.410964] Freeing unused kernel memory: 1024K
[ 3.415348] Run /sbin/init as init process
[ 4.297008] init: Console is alive
[ 4.297228] init: - watchdog -
[ 5.228185] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.302504] exFAT: Version 1.2.9
[ 5.310441] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.312392] SCSI subsystem initialized
[ 5.320293] ahci 29000000.sata: forcing port_map 0x0 -> 0x1
[ 5.320338] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 5.325061] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
[ 5.334276] scsi host0: ahci
[ 5.342148] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26
[ 5.677297] ata1: SATA link down (SStatus 0 SControl 300)
[ 5.681929] ehci-platform: EHCI generic platform driver
[ 5.690770] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.692194] ohci-platform: OHCI generic platform driver
[ 5.702202] dwc3 11000000.dwc3: Failed to get clk 'ref': -2
[ 5.757975] dwc3 10000000.dwc3: Failed to get clk 'ref': -2
[ 5.816910] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.817009] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.821609] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 5.829098] xhci-hcd xhci-hcd.0.auto: irq 43, io mem 0x11000000
[ 5.839485] hub 1-0:1.0: USB hub found
[ 5.844152] hub 1-0:1.0: 1 port detected
[ 5.848205] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.852030] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.857393] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 5.864972] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.871846] hub 2-0:1.0: USB hub found
[ 5.879816] hub 2-0:1.0: 1 port detected
[ 5.883540] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.887438] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 5.892784] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[ 5.900298] xhci-hcd xhci-hcd.1.auto: irq 44, io mem 0x10000000
[ 5.910176] hub 3-0:1.0: USB hub found
[ 5.915506] hub 3-0:1.0: 1 port detected
[ 5.919539] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.923384] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 5.928736] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.936301] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.943217] hub 4-0:1.0: USB hub found
[ 5.951168] hub 4-0:1.0: 1 port detected
[ 5.957190] usbcore: registered new interface driver usb-storage
[ 5.958803] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.970916] init: - preinit -
[ 7.944338] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 7.946364] dwmac1000: Master AXI performs any burst length
[ 7.953380] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 7.958728] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 7.966958] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 7.976600] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.036690] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.036802] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 14.148404] mount_root: loading kmods from internal overlay
[ 14.192460] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 14.194838] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 14.242209] print_req_error: I/O error, dev mtdblock0, sector 0
[ 14.243444] print_req_error: I/O error, dev mtdblock0, sector 8
[ 14.266667] print_req_error: I/O error, dev mtdblock0, sector 16
[ 14.276690] print_req_error: I/O error, dev mtdblock0, sector 24
[ 14.277939] print_req_error: I/O error, dev mtdblock0, sector 0
[ 14.281761] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 14.396970] print_req_error: I/O error, dev mtdblock0, sector 0
[ 14.397004] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 14.436561] print_req_error: I/O error, dev mtdblock1, sector 0
[ 14.447379] print_req_error: I/O error, dev mtdblock1, sector 8
[ 14.457364] print_req_error: I/O error, dev mtdblock1, sector 16
[ 14.458728] print_req_error: I/O error, dev mtdblock1, sector 24
[ 14.463819] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 14.517400] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.049473] UBIFS (ubi0:1): default file-system created
[ 15.050832] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 152
[ 15.153757] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.153785] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.160683] UBIFS (ubi0:1): FS size: 86343680 bytes (82 MiB, 680 LEBs), journal size 4317184 bytes (4 MiB, 34 LEBs)
[ 15.170528] UBIFS (ubi0:1): reserved for root: 4078225 bytes (3982 KiB)
[ 15.180782] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 0D78B6F4-1216-48D1-BF52-4FC08BF8E469, small LPT model
[ 15.216844] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 15.217009] block: unable to load configuration (fstab: Entry not found)
[ 15.222687] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 15.229903] block: unable to load configuration (fstab: Entry not found)
[ 15.235957] block: attempting to load /etc/config/fstab
[ 15.264357] block: extroot: not configured
[ 15.331988] UBIFS (ubi0:1): un-mount UBI device 0
[ 15.332146] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 15.341874] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 153
[ 15.429980] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.430004] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.436850] UBIFS (ubi0:1): FS size: 86343680 bytes (82 MiB, 680 LEBs), journal size 4317184 bytes (4 MiB, 34 LEBs)
[ 15.446753] UBIFS (ubi0:1): reserved for root: 4078225 bytes (3982 KiB)
[ 15.456997] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 0D78B6F4-1216-48D1-BF52-4FC08BF8E469, small LPT model
[ 15.482002] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.496591] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 15.502137] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.505694] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 15.689768] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 15.689848] block: unable to load configuration (fstab: Entry not found)
[ 15.695561] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 15.702608] block: unable to load configuration (fstab: Entry not found)
[ 15.708937] block: attempting to load /etc/config/fstab
[ 15.715763] block: extroot: not configured
[ 15.769646] mount_root: overlay filesystem has not been fully initialized yet
[ 15.770442] mount_root: switching to ubifs overlay
[ 15.805859] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
[ 15.807617] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 15.934458] procd: - early -
[ 15.934611] procd: - watchdog -
[ 16.650513] procd: - watchdog -
[ 16.650861] procd: - ubus -
[ 16.731320] procd: - init -
Please press Enter to activate this console.
[ 17.105565] urngd: v1.0.1 started.
[ 17.140958] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.156099] tun: Universal TUN/TAP device driver, 1.6
[ 17.158421] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 17.162266] gre: GRE over IPv4 demultiplexor driver
[ 17.166575] ip_gre: GRE over IPv4 tunneling driver
[ 17.193981] Mirror/redirect action on
[ 17.197582] u32 classifier
[ 17.197598] input device check on
[ 17.199215] Actions configured
[ 17.208451] fuse init (API version 7.27)
[ 17.210595] usbcore: registered new interface driver chaoskey
[ 17.212185] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[ 17.217149] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[ 17.247717] xt_time: kernel timezone is -0000
[ 17.269834] PPP generic driver version 2.4.2
[ 17.270406] PPP MPPE Compression module registered
[ 17.273855] NET: Registered protocol family 24
[ 17.278763] PPTP driver version 0.8.5
[ 17.290912] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
[ 17.296225] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 17.298386] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 17.913554] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed
[ 18.098413] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 18.160680] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 18.220282] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 18.522261] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 18.522293] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 18.533392] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-012-0ee2f206b api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 c3fbc410
[ 20.857431] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734
[ 26.694559] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 26.694621] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32
[ 26.776562] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 26.777385] ath10k_pci 0000:01:00.0: wmi print 'free: 81784 iram: 23220 sram: 14440'
[ 27.034064] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 27.139821] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x46.
[ 27.141987] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 27.147670] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 27.639148] firmware ath10k!fwcfg-pci-0001:01:00.0.txt: firmware_loading_store: map pages failed
[ 27.766863] firmware ath10k!QCA9984!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 27.802266] firmware ath10k!QCA9984!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 27.859656] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 27.859905] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 27.867636] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 27.881213] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-012-0ee2f206b api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 c3fbc410
[ 30.199800] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734
[ 36.036059] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 36.036091] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32
[ 36.120184] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 36.121046] ath10k_pci 0001:01:00.0: wmi print 'free: 81784 iram: 23220 sram: 14440'
[ 36.351622] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 36.485816] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 43.903948] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 43.905675] dwmac1000: Master AXI performs any burst length
[ 43.913000] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found
[ 43.918360] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 43.926580] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock
[ 43.935415] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 43.948608] br-lan: port 1(eth1.1) entered blocking state
[ 43.948647] br-lan: port 1(eth1.1) entered disabled state
[ 43.953804] device eth1.1 entered promiscuous mode
[ 43.958974] device eth1 entered promiscuous mode
[ 43.968607] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 43.977723] Generic PHY fixed-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00, irq=POLL)
[ 43.978756] dwmac1000: Master AXI performs any burst length
[ 43.986742] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[ 43.992025] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 44.004203] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[ 44.009575] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 44.042500] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 44.377229] print_req_error: 14 callbacks suppressed
[ 44.377235] print_req_error: I/O error, dev mtdblock0, sector 0
[ 44.387201] print_req_error: I/O error, dev mtdblock0, sector 8
[ 44.397156] print_req_error: I/O error, dev mtdblock0, sector 16
[ 44.398476] print_req_error: I/O error, dev mtdblock0, sector 24
[ 44.403690] print_req_error: I/O error, dev mtdblock0, sector 0
[ 44.408217] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 44.437206] print_req_error: I/O error, dev mtdblock0, sector 0
[ 44.437242] Buffer I/O error on dev mtdblock0, logical block 0, async page read
[ 44.457367] print_req_error: I/O error, dev mtdblock1, sector 0
[ 44.459964] print_req_error: I/O error, dev mtdblock1, sector 8
[ 44.468170] print_req_error: I/O error, dev mtdblock1, sector 16
[ 44.477415] print_req_error: I/O error, dev mtdblock1, sector 24
[ 44.507393] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 44.519925] Buffer I/O error on dev mtdblock1, logical block 0, async page read
[ 44.958754] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 45.036611] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 45.049039] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 45.049328] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 45.054339] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 45.064111] br-lan: port 1(eth1.1) entered blocking state
[ 45.066911] br-lan: port 1(eth1.1) entered forwarding state
[ 45.087701] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.31.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r11619-f6385f30bd
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment