Skip to content

Instantly share code, notes, and snippets.

@itszero
Created March 12, 2010 11:09
Show Gist options
  • Save itszero/330233 to your computer and use it in GitHub Desktop.
Save itszero/330233 to your computer and use it in GitHub Desktop.
u-boot log
==========
Texas Instruments X-Loader 1.41
Starting OS Bootloader...
U-Boot 1.3.3-svn333 (Sep 10 2009 - 16:49:01)
OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz
OMAP3 DevKit8000 Board + LPDDR/NAND
DRAM: 256 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
OMAP3 DevKit8000 # mmcinit
OMAP3 DevKit8000 # fatload mmc 0 0x80000000 u-boot.bin
reading u-boot.bin
224740 bytes read
OMAP3 DevKit8000 # go 0x80000000
## Starting application at 0x80000000 ...
U-Boot 2009.11-00422-g1ad742a-dirty (Mar 09 2010 - 13:35:14)
OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
OMAP3 DevKit8000 + LPDDR/NAND
I2C: ready
DRAM: 256 MB
NAND: 256 MiB
Using default environment
In: serial
Out: serial
Err: serial
ethaddr not set, using Die ID
Die ID #66da000400000000040364320e01a01a
Net: dm9000
Hit any key to stop autoboot: 0
mmc0 is available
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
1489572 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-2.6.33-rc6-07700-g12ad0d2-
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1489508 Bytes = 1.4 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Kernel boot log
===============
Linux version 2.6.33-rc6-07700-g12ad0d2-dirty (kanru@anar) (gcc version 4.4.1 (0xlab) ) #47 Wed Mar 10 15:34:28 CST 2010
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: OMAP3 Devkit8000
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.rotate=1 omapdss.def_disp=lcd root=/dev/mmcblk0p2 init=/init rw
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 244352KB available (2116K code, 216K data, 684K init, 0K highmem)
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/266/500 MHz
Could not get uart4_ick
Could not get uart4_fck
Reprogramming SDRC clock to 266000000 Hz
dpll3_m2_clk rate change failed: -22
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER12 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 328.73 BogoMIPS (lpj=1282048)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
mux: Could not set signal i2c3_scl
mux: Could not set signal i2c3_sda
mux: Could not set gpio170
Found NAND on CS0
Registering NAND on CS0
mux: Could not set signal sdr_cke0
mux: Could not set signal sdr_cke1
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
mux: Could not set gpio29
mux: Could not set signal sdmmc1_clk
mux: Could not set signal sdmmc1_cmd
mux: Could not set signal sdmmc1_dat0
mux: Could not set signal sdmmc1_dat1
mux: Could not set signal sdmmc1_dat2
mux: Could not set signal sdmmc1_dat3
mux: Could not set signal sdmmc1_dat4
mux: Could not set signal sdmmc1_dat5
mux: Could not set signal sdmmc1_dat6
mux: Could not set signal sdmmc1_dat7
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VDVI: 1800 mV normal standby
regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
io scheduler noop registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "X-Loader"
0x000000080000-0x000000260000 : "U-Boot"
0x000000260000-0x000000280000 : "U-Boot Env"
0x000000280000-0x000000680000 : "Kernel"
0x000000680000-0x000010000000 : "File System"
dm9000 Ethernet Driver, V1.31
dm9000 dm9000: eth%d: Invalid ethernet MAC address. Please set using ifconfig
eth0: dm9000a at d0808000,d080c400 IRQ 185 MAC: 00:00:00:00:00:00 (chip)
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC 0e:1d:41:19:b7:66
usb0: HOST MAC 86:cc:18:73:f4:b8
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
input: TWL4030 Keypad as /devices/platform/i2c_omap.1/i2c-1/1-004a/twl4030_keypad/input/input0
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
twl_rtc twl_rtc: Enabling TWL-RTC.
Registered led device: led1
Registered led device: led2
Registered led device: ledB
Registered led device: led3
TCP cubic registered
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment