buildroot-Amlogic + buildroot-linux-kernel-m6

gistfile1.txt

U-Boot Version: 2011.03-d65283f(20130116.153713)
I2C:   ready
aml_rtc_init
DRAM:  1 GiB
relocation Offset is: 105fc000
NAND:  Amlogic nand flash uboot driver, Version U1.01.005 (c) 2010 Amlogic Inc.
No NAND device found!!!
NAND device id: 2c 68 4 4a a9 0 
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
aml nand env valid addr: 90000 
Creating 6 MTD partitions on "nandnormal":
0x000000800000-0x000000c00000 : "logo"
0x000000c00000-0x000001400000 : "boot"
0x000001400000-0x000021400000 : "system"
 NAND bbt detect Bad block at 5a00000 
0x000021400000-0x000040800000 : "cache"
0x000040800000-0x000053400000 : "backup"
0x000053400000-0x000100000000 : "userdata"
nandnormal initialized ok
MMC:   SDIO Port B: 0
spi_claim_bus: bus:0 cs:0
SF: Detected MX25L3205D with page size 256, total 4 MiB

SPI NOR Flash have write protect!!!
spi_release_bus: bus:0 cs:0
spi_claim_bus: bus:0 cs:0
spi_release_bus: bus:0 cs:0
In:    serial
Out:   serial
Err:   serial
register usb cfg[0] = 9fe85cf8
Net:   Meson_Ethernet
init suspend firmware done. (ret:0)
>>>>>>>>>>>>>>>>> adc_val = 227
>>>>>>>>>>>>>>>>> adc_val = 929
>>>>>>>>>>>>>>>>> board_id = 11
spi_claim_bus: bus:0 cs:0
SF: Detected MX25L3205D with page size 256, total 4 MiB

SPI NOR Flash have write protect!!!
spi_release_bus: bus:0 cs:0
4096 KiB MX25L3205D at 0:0 is now current device
spi_claim_bus: bus:0 cs:0
spi_release_bus: bus:0 cs:0
efuse mac is : 00:0d:fe:59:78:e1 
set ethaddr is : 00:0d:fe:59:78:e1 
spi_claim_bus: bus:0 cs:0
SF: Detected MX25L3205D with page size 256, total 4 MiB

SPI NOR Flash have write protect!!!
spi_release_bus: bus:0 cs:0
4096 KiB MX25L3205D at 0:0 is now current device
spi_claim_bus: bus:0 cs:0
spi_release_bus: bus:0 cs:0
reboot_mode=charging
SARADC open channel(4).
get_adc_sample(4): 0x3fa
get_adc_sample(4): 0x3fa
oemid:FF FE
flag: 0xFFFE
hwid:FF 00 00 14 F1 03 25 A4
upgrade_step = 2
get_adc_sample(4): 0x3fa
get_adc_key(): 0
Normal Start...
Hit any key to stop autoboot:  1  0 
Booting from nand ...

NAND read: boot whole chip
 8388608 bytes read: OK

NAND read: logo whole chip
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.0.8
   Image Type:   ARM Linux Kernel Image (lzma compressed)
   Data Size:    3790031 Bytes = 3.6 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
machid from environment: 0x4e27 
EFUSE machid is not set.
Using machid 0x4e27 from environment

Starting kernel ...

[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Linux version 3.0.8 (root@build) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 SMP PREEMPT Thu Mar 21 18:28:45 UTC 2013
[    0.000000@0] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
[    0.000000@0] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000@0] Machine: Amlogic Meson6 g02 reference platform
[    0.000000@0] Ignoring unrecognised tag 0x00000000
[    0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[    0.000000@0] PERCPU: Embedded 7 pages/cpu @c12d9000 s7072 r8192 d13408 u32768
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 231424
[    0.000000@0] Kernel command line: root=/dev/mtdblock2 rw rootfstype=yaffs2 init=/sbin/init rootwait console=ttyS0,115200n8 a9_clk_max=1512000000 logo=osd1,0x84100000,720p,full androidboot.resolution=720p nohlt mem=1024M vmalloc=256m mac=00:0d:fe:59:78:e1 verhw=MX_NORMAL subverhw=MX0 hdmitx=false
[    0.000000@0] osd1:1
[    0.000000@0] 720p:6
[    0.000000@0] full:2
[    0.000000@0] HDMI DEBUG: hdmitx_boot_para_setup [1334]
[    0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000@0] Memory: 64MB 336MB 512MB = 912MB total
[    0.000000@0] Memory: 914980k/914980k available, 18908k reserved, 524288K highmem
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000@0]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000@0]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000@0]     vmalloc : 0xe0000000 - 0xf0000000   ( 256 MB)
[    0.000000@0]     lowmem  : 0xc0000000 - 0xdff00000   ( 511 MB)
[    0.000000@0]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000@0]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000@0]       .init : 0xc0008000 - 0xc0037000   ( 188 kB)
[    0.000000@0]       .text : 0xc0037000 - 0xc090fb14   (9059 kB)
[    0.000000@0]       .data : 0xc0910000 - 0xc09677e0   ( 350 kB)
[    0.000000@0]        .bss : 0xc0967804 - 0xc0acfe88   (1442 kB)
[    0.000000@0] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0]   RCU debugfs-based tracing is enabled.
[    0.000000@0] NR_IRQS:256
[    0.000000@0] gic_init: irq_offset=0
[    0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[    0.000000@0] MESON TIMER-A c0924100
[    0.000000@0] Console: colour dummy device 80x30
[    0.000000@0] console [ttyS0] enabled
[    0.241689@0] Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
[    0.300048@0] pid_max: default: 32768 minimum: 301
[    0.302321@0] Mount-cache hash table entries: 512
[    0.307556@0] Initializing cgroup subsys cpuacct
[    0.311492@0] Initializing cgroup subsys freezer
[    0.316080@0] CPU: Testing write buffer coherency: ok
[    0.321251@0] MESON TIMER-B c09241c0
[    0.324712@0] L310 cache controller enabled
[    0.328776@0] l2x0: 8 ways, CACHE_ID 0x4100a0c8, AUX_CTRL 0x3e462c01, Cache size: 524288 B
[    0.337068@0] ===actlr=0x41
[    0.339797@0] ===actlr=0x49
[    0.342582@0] pl310: aux=0x3e462c01, prefetch=0x31000006
[    0.441541@1] CPU1: Booted secondary processor
[    0.501275@1] MESON TIMER-D c0924340
[    0.501306@0] Brought up 2 CPUs
[    0.501314@0] SMP: Total of 2 processors activated (4780.85 BogoMIPS).
[    0.513508@0] devtmpfs: initialized
[    0.520717@0] clkrate [ xtal ] : 24000000
[    0.520888@0] clkrate [ pll_sys ] : 1200000000
[    0.525268@0] clkrate [ pll_fixed ] : 2000000000
[    0.529849@0] clkrate [ pll_vid2 ] : 378000000
[    0.534284@0] clkrate [ pll_hpll ] : 378000000
[    0.538768@0] clkrate [ pll_ddr ] : 504000000
[    0.543115@0] clkrate [ a9_clk ] : 1200000000
[    0.547447@0] clkrate [ clk81 ] : 200000000
[    0.551651@0] clkrate [ usb0 ] : 0
[    0.555031@0] clkrate [ usb1 ] : 0
[    0.559188@0] print_constraints: dummy: 
[    0.562386@0] NET: Registered protocol family 16
[    0.567662@0] register lm device 0
[    0.570290@0] register lm device 1
[    0.573692@0] [wifi_dev_init] in
[    0.576806@0] [wifi_clock_enable] in
[    0.582878@0] usb_wifi_power Off
[    0.583721@0] chip version=ffffffff
[    0.587054@0] tv_init_module
[    0.589920@0] major number 254 for disp

[    0.593831@0] vout_register_server
[    0.597205@0] register tv module server ok 

[    0.601556@0] major number 0 for disp

[    0.605190@0] register tv module server ok 

[    0.609529@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_init
[    0.614939@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
[    0.620471@0] master_no = 0, resource = c0926298, maseter_regs=f1108500
[    0.627196@0] aml-i2c aml-i2c.0: add adapter aml_i2c_adap0(df808428)
[    0.633412@0] aml-i2c aml-i2c.0: aml i2c bus driver.
[    0.638444@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
[    0.643915@0] master_no = 1, resource = c09262f0, maseter_regs=f11087c0
[    0.650700@0] aml-i2c aml-i2c.1: add adapter aml_i2c_adap1(df808828)
[    0.656846@0] aml-i2c aml-i2c.1: aml i2c bus driver.
[    0.661873@0] drivers/amlogic/i2c/aml_i2c.c : aml_i2c_probe
[    0.667341@0] master_no = 2, resource = c0926348, maseter_regs=f3100500
[    0.674129@0] aml-i2c aml-i2c.2: add adapter aml_i2c_adap2(df808c28)
[    0.680273@0] aml-i2c aml-i2c.2: aml i2c bus driver.
[    0.685538@0] i2c i2c-2: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(2) 100K addr 0x34
[    0.694287@0] i2c i2c-2: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(2) 100K addr 0x34
[    0.703222@0] i2c i2c-2: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(2) 100K addr 0x34
[    0.712050@0] axp_mfd 2-0034: failed reading at 0x03
[    0.716989@0] [AXP20-MFD] try to read chip id failed!
[    0.722038@0] axp_mfd: probe of 2-0034 failed with error -11
[    0.757197@0] bio: create slab <bio-0> at 0
[    0.758083@0] SCSI subsystem initialized
[    0.759947@0] usbcore: registered new interface driver usbfs
[    0.765582@0] usbcore: registered new interface driver hub
[    0.770951@0] usbcore: registered new device driver usb
[    0.776518@0] [0x1b7e] = 0xff
[    0.778999@0] [0x105f] = 0x0
[    0.781887@0] [0x109d] = 0x814d3928
[    0.785336@0] [0x109e] = 0x6b425012
[    0.788808@0] [0x109f] = 0x110
[    0.791855@0] [0x109c] = 0x1043e
[    0.795057@0] [0x1066] = 0x10843
[    0.798268@0] [0x1059] = 0x100
[    0.801314@0] [0x105f] = 0x80000
[    0.804519@0] [0x105f] = 0x88001
[    0.807730@0] [0x105f] = 0x80003
[    0.810941@0] [0x104a] = 0x101
[    0.813987@0] [0x107f] = 0x8c0000c3
[    0.817452@0] [0x1bb8] = 0x52
[    0.820403@0] [0x1b62] = 0x2029
[    0.823533@0] [0x1b8d] = 0x40
[    0.826479@0] [0x1b8e] = 0x19
[    0.829430@0] [0x1b94] = 0x288
[    0.832475@0] [0x1b95] = 0xc87
[    0.835506@0] [0x1b97] = 0xce3
[    0.838544@0] [0x1b98] = 0x50
[    0.841501@0] [0x1b99] = 0xf0
[    0.844447@0] [0x1b9a] = 0x50
[    0.847398@0] [0x1b9b] = 0x2b0
[    0.850436@0] [0x1b9c] = 0xcb0
[    0.853480@0] [0x1b9d] = 0x4
[    0.856338@0] [0x1b9e] = 0x8
[    0.859203@0] [0x1ba1] = 0x4
[    0.862072@0] [0x1ba2] = 0x8
[    0.864932@0] [0x1ba4] = 0x288
[    0.867970@0] [0x1ba3] = 0xc87
[    0.871008@0] [0x1ba6] = 0x1d
[    0.873964@0] [0x1baf] = 0x2ec
[    0.876997@0] [0x1ba7] = 0x100
[    0.880035@0] [0x1ba8] = 0xa8
[    0.882991@0] [0x1ba9] = 0xa8
[    0.885937@0] [0x1baa] = 0x100
[    0.888975@0] [0x1bab] = 0x0
[    0.891844@0] [0x1bac] = 0x5
[    0.894704@0] [0x1bae] = 0x2ed
[    0.897742@0] [0x1b68] = 0x100
[    0.900780@0] [0x1b60] = 0x0
[    0.903649@0] [0x1b6e] = 0x200
[    0.906683@0] [0x1b58] = 0x0
[    0.909547@0] [0x1b7e] = 0x0
[    0.912416@0] [0x1b64] = 0x9061
[    0.915536@0] [0x1b65] = 0xa061
[    0.918661@0] [0x1b66] = 0xb061
[    0.921791@0] [0x1b78] = 0x1
[    0.924650@0] [0x1b79] = 0x1
[    0.927515@0] [0x1b7a] = 0x1
[    0.930379@0] [0x1b7b] = 0x1
[    0.933248@0] [0x1b7c] = 0x1
[    0.936108@0] [0x1b7d] = 0x1
[    0.938972@0] [0x271a] = 0xa
[    0.941841@0] [0x1bfc] = 0x1000
[    0.944961@0] [0x1c0d] = 0x3210
[    0.948086@0] [0x1c0e] = 0x54
[    0.951037@0] [0x1b80] = 0x1
[    0.953907@0] [0x1b57] = 0x0
[    0.956767@0] tvoutc_setmode[255]
[    0.960065@0] mode is: 6
[    0.962590@0] VPU_VIU_VENC_MUX_CTRL: 0xa
[    0.966487@0] viu chan = 1
[    0.969178@0] VPU_VIU_VENC_MUX_CTRL: 0xa
[    1.012697@0] print_constraints: vcck: 931 <--> 1308 mV at 1308 mV 
[    1.013852@0] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    1.020502@0] Bluetooth: Core ver 2.16
[    1.023781@0] NET: Registered protocol family 31
[    1.028248@0] Bluetooth: HCI device and connection manager initialized
[    1.034774@0] Bluetooth: HCI socket layer initialized
[    1.039794@0] Bluetooth: L2CAP socket layer initialized
[    1.045024@0] Bluetooth: SCO socket layer initialized
[    1.050363@0] cfg80211: Calling CRDA to update world regulatory domain
[    1.057277@0] Switching to clocksource Timer-E
[    1.061269@0] Switched to NOHz mode on CPU #0
[    1.061288@1] Switched to NOHz mode on CPU #1
[    1.079245@1] NET: Registered protocol family 2
[    1.079384@1] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[    1.085778@1] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    1.093498@1] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    1.100271@1] TCP: Hash tables configured (established 65536 bind 65536)
[    1.106283@1] TCP reno registered
[    1.109563@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    1.115577@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    1.122220@1] NET: Registered protocol family 1
[    1.126739@1] RPC: Registered named UNIX socket transport module.
[    1.132594@1] RPC: Registered udp transport module.
[    1.137446@1] RPC: Registered tcp transport module.
[    1.142292@1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.162375@1] highmem bounce pool size: 64 pages
[    1.162725@1] ashmem: initialized
[    1.172613@1] VFS: Disk quotas dquot_6.5.2
[    1.172862@1] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.180139@1] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.185976@1] NTFS driver 2.1.30 [Flags: R/W].
[    1.188482@1] fuse init (API version 7.16)
[    1.192938@1] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[    1.202890@1] msgmni has been set to 763
[    1.205428@1] io scheduler noop registered
[    1.208655@1] io scheduler deadline registered (default)
[    1.359532@0] loop: module loaded
[    1.361286@0] PPP generic driver version 2.4.2
[    1.362156@0] PPP Deflate Compression module registered
[    1.366932@0] PPP BSD Compression module registered
[    1.372197@0] PPP MPPE Compression module registered
[    1.376737@0] NET: Registered protocol family 24
[    1.381523@0] usbcore: registered new interface driver asix
[    1.387004@0] usbcore: registered new interface driver cdc_ether
[    1.393035@0] usbcore: registered new interface driver net1080
[    1.398794@0] usbcore: registered new interface driver cdc_subset
[    1.404879@0] usbcore: registered new interface driver zaurus
[    1.410510@0] cdc_ncm: 04-Aug-2011
[    1.413997@0] usbcore: registered new interface driver cdc_ncm
[    1.420045@0] usbcore: registered new interface driver cdc_acm
[    1.425527@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.433684@0] Initializing USB Mass Storage driver...
[    1.438821@0] usbcore: registered new interface driver usb-storage
[    1.444882@0] USB Mass Storage support registered.
[    1.449873@0] usbcore: registered new interface driver usbserial
[    1.455649@0] usbserial: USB Serial Driver core
[    1.460238@0] USB Serial support registered for GSM modem (1-port)
[    1.466418@0] usbcore: registered new interface driver option
[    1.472052@0] option: v0.7.2:USB Driver for GSM modems
[    1.477929@0] mousedev: PS/2 mouse device common for all mice
[    1.483617@0] i2c /dev entries driver
[    1.487512@0] lirc_dev: IR Remote Control driver registered, major 251 
[    1.493148@0] IR NEC protocol handler initialized
[    1.497820@0] IR RC5(x) protocol handler initialized
[    1.502783@0] IR RC6 protocol handler initialized
[    1.507455@0] IR JVC protocol handler initialized
[    1.512149@0] IR Sony protocol handler initialized
[    1.516917@0] IR RC5 (streamzap) protocol handler initialized
[    1.522652@0] IR LIRC bridge handler initialized
[    1.527245@0] Linux video capture interface: v2.00
[    1.532958@0] device-mapper: uevent: version 1.0.3
[    1.537412@0] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[    1.545659@0] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    1.551259@0] usbcore: registered new interface driver btusb
[    1.556770@0] cpufreq_gov_dbs_init
[    1.560241@0] cpuidle: using governor ladder
[    1.564409@0] cpuidle: using governor menu
[    1.568918@0] usbcore: registered new interface driver usbhid
[    1.574216@0] usbhid: USB HID core driver
[    1.578931@0] logger: created 256K log 'log_main'
[    1.583152@0] logger: created 256K log 'log_events'
[    1.587964@0] logger: created 256K log 'log_radio'
[    1.592759@0] logger: created 256K log 'log_system'
[    1.597721@0] vout_init_module
[    1.600442@0] start init vout module 

[    1.604255@0] create  vout attribute ok 

[    1.608228@0] ge2d_init
[    1.610579@0] ge2d_dev major:250

[    1.614304@0] ge2d start monitor

[    1.617212@0] osd_init
[    1.617217@1] ge2d workqueue monitor start

[    1.623725@0] [osd0] 0x84100000-0x84afffff
[    1.627928@0] Frame buffer memory assigned at phy:0x84100000, vir:0xe1000000, size=10240K
[    1.635935@0] ---------------clear framebuffer0 memory  

[    1.648447@0] [osd1] 0x84b00000-0x84bfffff
[    1.648498@0] Frame buffer memory assigned at phy:0x84b00000, vir:0xe0200000, size=1024K
[    1.655073@0] init fbdev bpp is :24

[    1.658957@0] osd probe ok  

[    1.661797@0] vout2_init_module enter
[    1.665239@0] start init vout2 module 

[    1.669134@0] create  vout2 attribute ok 

[    1.673852@0]  set pinmux c09266a4
[    1.701026@0] UART_ttyS0:(irq = 122)
[    1.701162@0] Amlogic nand flash AVOS driver for M3, Version 1.1 (c) 2010 Amlogic Inc.
[    1.706971@0] 1
[    1.708678@0] chip->controller=c0aae518
[    1.712523@0] init bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.0ns
[    1.720691@0] No NAND device found.
[    1.724171@0] NAND device id: 2c 68 4 4a a9 0 
[    1.728557@0] NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
[    1.738088@0] bus_cycle=4, bus_timing=5, start_cycle=5, end_cycle=6,system=5.0ns
[    1.773642@0] aml nand env valid addr: 90000 
[    1.788864@0] Creating 6 MTD partitions on "C revision NAND 4GiB MT29F32G-C":
[    1.790445@0] 0x000000800000-0x000000c00000 : "logo"
[    1.796675@0] 0x000000c00000-0x000001400000 : "boot"
[    1.801445@0] 0x000001400000-0x000021400000 : "system"
[    1.805462@0]  NAND bbt detect Bad block at 5a00000 
[    1.811518@0] 0x000021400000-0x000040800000 : "cache"
[    1.816493@0] 0x000040800000-0x000053400000 : "backup"
[    1.821644@0] 0x000053400000-0x000100000000 : "userdata"
[    1.827087@0] dwc_otg: version 2.94a 30-MAY-2012
[    2.329731@0] USB (0) use clock source: XTAL input
[    2.530513@0] Core Release: 2.94a
[    2.530536@0] Setting default values for core params
[    2.733097@0] Using Buffer DMA mode
[    2.733121@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[    2.735543@0] Working on port type = OTG
[    2.739448@0] Current port type: SLAVE
[    2.743241@0] dwc_otg lm0: DWC OTG Controller
[    2.747597@0] dwc_otg lm0: new USB bus registered, assigned bus number 1
[    2.754238@0] dwc_otg lm0: irq 62, io mem 0x00000000
[    2.759943@0] hub 1-0:1.0: USB hub found
[    2.763088@0] hub 1-0:1.0: 1 port detected
[    2.767398@0] Dedicated Tx FIFOs mode
[    2.770890@0] alloc_wrapper: df810000
[    2.774462@0] using timer detect id change, df80b400
[    2.881010@0] DEBUG:DWC_WORKQ_SCHEDULE:: Queueing work: connection id status change, container=df19f9c0
[    2.884858@0] HOST mode
[    3.078823@0] Using Buffer DMA mode
[    3.078846@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[    3.087873@0] DEBUG:DWC_WORKQ_SCHEDULE_DELAYED:: Queueing work: start hcd, container=df19fe40
[    3.087892@1] Core Release: 2.94a
[    3.087899@1] Setting default values for core params
[    3.099105@0] DEBUG:do_work:: Work done: connection id status change, container=df19f9c0
[    3.141069@0] Init: Port Power? op_state=1
[    3.141092@0] Init: Power Port (0)
[    3.142991@0] set usb port power on (board gpio 25)!
[    3.147970@0] DEBUG:do_work:: Work done: start hcd, container=df19fe40
[    3.287816@1] Using Buffer DMA mode
[    3.287839@1] OTG VER PARAM: 1, OTG VER FLAG: 1
[    3.290257@1] Working on port type = HOST
[    3.294302@1] dwc_otg lm1: DWC OTG Controller
[    3.298620@1] dwc_otg lm1: new USB bus registered, assigned bus number 2
[    3.305306@1] dwc_otg lm1: irq 63, io mem 0x00000000
[    3.310275@1] Init: Port Power? op_state=1
[    3.314329@1] Init: Power Port (0)
[    3.318471@1] hub 2-0:1.0: USB hub found
[    3.321619@1] hub 2-0:1.0: 1 port detected
[    3.326060@1] Amlogic A/V streaming port init
[    3.332618@1] regist mpeg12 codec profile
[    3.334104@1] regist mpeg4 codec profile
[    3.337909@1] amvdec_vc1 module init
[    3.341606@1] regist vc1 codec profile
[    3.345201@1] amvdec_h264 module init
[    3.348945@1] regist h264 codec profile
[    3.352821@1] regist mjpeg codec profile
[    3.356572@1] amvdec_real module init
[    3.360317@1] regist real codec profile
[    3.365898@1] SARADC Driver init.
[    3.367590@1] ADC Keypad Driver init.
[    3.371039@1] chan #4 used for ADC key
[    3.374714@1] menu key(139) registed.
[    3.378359@1] vol- key(114) registed.
[    3.382029@1] vol+ key(115) registed.
[    3.385650@1] home key(102) registed.
[    3.389296@1] back key(158) registed.
[    3.393184@1] input: adc_keypad as /devices/platform/m1-adckp.0/input/input0
[    3.400363@1] adc keypad register input device completed.

[    3.405494@1] adc keypad major:248

[    3.409436@1] Meson KeyInput init
[    3.412280@1] Key 116 registed.
[    3.415531@1] input: key_input as /devices/platform/meson-keyinput.0/input/input1
[    3.423185@1] Meson KeyInput register RTC interrupt
[    3.427514@1] Meson KeyInput major=247
[    3.431446@1] Indeed it is in host mode hprt0 = 00021501
[    3.451857@0] Memory Card media Major: 253
[    3.452021@0] card max_req_size is 128K 
[    3.454920@0] [extern_wifi_set_enable] in
[    3.458300@0] WIFI  Enable! 
[    3.461254@0] card creat process sucessful
[    3.465441@0] [dsp]DSP start addr 0xc4000000
[    3.469517@0] [dsp]register dsp to char divece(232)
[    3.476057@0] using rtc device, aml_rtc, for alarms
[    3.479059@0] aml_rtc aml_rtc: rtc core: registered aml_rtc as rtc0
[    3.488073@0] amvdec_viuin module init
[    3.489367@0] amvdec_viuin probe start.
[    3.493049@0] amvdec_viuin probe end.
[    3.496770@0] amvdec_656in module init
[    3.500452@0] amvdec_656in probe start.
[    3.504249@0] amvdec_656in probe end.
[    3.508531@0]  vdin[0] memory start addr is 86c00000, mem_size is 2000000 . 
[    3.514911@0] vdin0: flags:0x0
[    3.517949@0] vdin: driver initialized ok
[    3.522213@0] efuse===========================================
[    3.528185@0] efuse: device efuse created
[    3.531859@0] efuse--------------------------------------------
[    3.537902@0] boot_monitor: device successfully initialized.
[    3.543393@0] boot_monitor: driver successfully loaded.
[    3.549426@0] HDMI DEBUG: amhdmitx_init [1227]HDMI DEBUG: amhdmitx_probe [1084]hdmitx_device addr:c0abd77cSet HDMI:Chip C
[    3.559417@1] HDMI DEBUG: HDMITX_M1B_Init [3106]
[    3.564232@1] HDMI REG0x10:0xff
[    3.566904@0] wm8960-codec 1-001a: No platform data supplied
[    3.566985@0] i2c i2c-1: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(1) 300K addr 0x1a
[    3.567035@0] i2c i2c-1: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(1) 300K addr 0x1a
[    3.567083@0] i2c i2c-1: [aml_i2c_xfer] error ret = -5 (-EIO) token 1, master_no(1) 300K addr 0x1a
[    3.567091@0] wm8960-codec 1-001a: Failed to issue reset
[    3.567097@0] wm8960-codec 1-001a: asoc: failed to probe CODEC wm8960-codec.1-001a: -11
[    3.567151@0] asoc: failed to instantiate card AML-WM8960: -11
[    3.567330@0] ALSA device list:
[    3.567335@0]   No soundcards found.
[    3.567545@0] GACT probability NOT on
[    3.567560@0] Mirror/redirect action on
[    3.567567@0] u32 classifier
[    3.567571@0]     Actions configured
[    3.567578@0] Netfilter messages via NETLINK v0.30.
[    3.567649@0] nf_conntrack version 0.5.0 (14296 buckets, 57184 max)
[    3.568210@0] ctnetlink v0.93: registering with nfnetlink.
[    3.568268@0] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    3.568274@0] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    3.569140@0] xt_time: kernel timezone is -0000
[    3.569326@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.569473@0] arp_tables: (C) 2002 David S. Miller
[    3.569530@0] TCP cubic registered
[    3.570938@0] NET: Registered protocol family 10
[    3.571800@0] Mobile IPv6
[    3.571842@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    3.571970@0] IPv6 over IPv4 tunneling driver
[    3.573479@0] NET: Registered protocol family 17
[    3.573524@0] NET: Registered protocol family 15
[    3.573705@0] Bridge firewalling registered
[    3.573861@0] Bluetooth: RFCOMM TTY layer initialized
[    3.573878@0] Bluetooth: RFCOMM socket layer initialized
[    3.573884@0] Bluetooth: RFCOMM ver 1.11
[    3.573890@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.573895@0] Bluetooth: BNEP filters: protocol multicast
[    3.573901@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.574184@0] NET: Registered protocol family 35
[    3.574296@0] lib80211: common routines for IEEE802.11 drivers
[    3.574310@0] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    3.762474@1] usb 1-1: new high speed USB device number 2 using dwc_otg
[    3.762539@1] HDMI DEBUG: HDMITX_M1B_Init [3110]
[    3.762545@1] HDMI DEBUG: hdmi_hw_init [1172]
[    3.763424@1] HDMI DEBUG: hdmi_task_handle [844]
[    3.787017@0] [extern_wifi_set_enable] in
[    3.791149@1] Indeed it is in host mode hprt0 = 00001101
[    3.791379@0] WIFI  Enable! 
[    3.791389@0] 
[    3.791391@0] SD/MMC initialization started......
[    3.805688@1] enter meson_pm_probe!
[    3.809054@1] meson_pm_probe done !
[    3.821304@0] set voltage to 1283000; selector=1
[    3.821602@0] ------------[ cut here ]------------
[    3.825152@0] WARNING: at kernel/smp.c:459 smp_call_function_many+0xe0/0x284()
[    3.832339@0] Modules linked in:
[    3.835576@0] [<c004591c>] (unwind_backtrace+0x0/0x10c) from [<c00668c8>] (warn_slowpath_common+0x54/0x64)
[    3.845194@0] [<c00668c8>] (warn_slowpath_common+0x54/0x64) from [<c00668f4>] (warn_slowpath_null+0x1c/0x24)
[    3.855000@0] [<c00668f4>] (warn_slowpath_null+0x1c/0x24) from [<c0098ba4>] (smp_call_function_many+0xe0/0x284)
[    3.865070@0] [<c0098ba4>] (smp_call_function_many+0xe0/0x284) from [<c0098d80>] (smp_call_function+0x38/0x68)
[    3.875051@0] [<c0098d80>] (smp_call_function+0x38/0x68) from [<c004da48>] (clk_set_rate_a9+0x90/0xd8)
[    3.884344@0] [<c004da48>] (clk_set_rate_a9+0x90/0xd8) from [<c004ca54>] (meson_clk_set_rate+0x1bc/0x1fc)
[    3.893888@0] [<c004ca54>] (meson_clk_set_rate+0x1bc/0x1fc) from [<c004cb28>] (clk_set_rate+0x94/0xbc)
[    3.903179@0] [<c004cb28>] (clk_set_rate+0x94/0xbc) from [<c0056c90>] (meson_cpufreq_target_locked+0x124/0x214)
[    3.913245@0] [<c0056c90>] (meson_cpufreq_target_locked+0x124/0x214) from [<c0056dac>] (meson_cpufreq_target+0x2c/0x44)
[    3.924011@0] [<c0056dac>] (meson_cpufreq_target+0x2c/0x44) from [<c0472e00>] (__cpufreq_driver_target+0x5c/0x60)
[    3.934252@0] [<c0472e00>] (__cpufreq_driver_target+0x5c/0x60) from [<c04756ac>] (cpufreq_governor_performance+0x28/0x30)
[    3.945187@0] [<c04756ac>] (cpufreq_governor_performance+0x28/0x30) from [<c0472fcc>] (__cpufreq_governor+0xc0/0x138)
[    3.955774@0] [<c0472fcc>] (__cpufreq_governor+0xc0/0x138) from [<c0473168>] (__cpufreq_set_policy+0x124/0x160)
[    3.965843@0] [<c0473168>] (__cpufreq_set_policy+0x124/0x160) from [<c047430c>] (cpufreq_add_dev_interface+0x2d0/0x320)
[    3.976607@0] [<c047430c>] (cpufreq_add_dev_interface+0x2d0/0x320) from [<c0474718>] (cpufreq_add_dev+0x3bc/0x4d0)
[    3.986940@0] [<c0474718>] (cpufreq_add_dev+0x3bc/0x4d0) from [<c03a7820>] (sysdev_driver_register+0xc4/0x14c)
[    3.996920@0] [<c03a7820>] (sysdev_driver_register+0xc4/0x14c) from [<c0473840>] (cpufreq_register_driver+0x84/0x1fc)
[    4.007511@0] [<c0473840>] (cpufreq_register_driver+0x84/0x1fc) from [<c03aa440>] (platform_drv_probe+0x14/0x18)
[    4.017666@0] [<c03aa440>] (platform_drv_probe+0x14/0x18) from [<c03a8f3c>] (driver_probe_device+0x7c/0x184)
[    4.027472@0] [<c03a8f3c>] (driver_probe_device+0x7c/0x184) from [<c03a90d0>] (__driver_attach+0x8c/0x90)
[    4.037020@0] [<c03a90d0>] (__driver_attach+0x8c/0x90) from [<c03a870c>] (bus_for_each_dev+0x5c/0x98)
[    4.046221@0] [<c03a870c>] (bus_for_each_dev+0x5c/0x98) from [<c03a8004>] (bus_add_driver+0x1e0/0x2b4)
[    4.055508@0] [<c03a8004>] (bus_add_driver+0x1e0/0x2b4) from [<c03a96a4>] (driver_register+0x78/0x18c)
[    4.064799@0] [<c03a96a4>] (driver_register+0x78/0x18c) from [<c03aa8ec>] (platform_driver_probe+0x18/0xa0)
[    4.074526@0] [<c03aa8ec>] (platform_driver_probe+0x18/0xa0) from [<c00375b8>] (do_one_initcall+0x34/0x170)
[    4.084243@0] [<c00375b8>] (do_one_initcall+0x34/0x170) from [<c00083dc>] (kernel_init+0xa8/0x13c)
[    4.093185@0] [<c00083dc>] (kernel_init+0xa8/0x13c) from [<c003ed00>] (kernel_thread_exit+0x0/0x8)
[    4.102128@0] ---[ end trace 0d6171e9dd60f80f ]---
[    4.106889@0] ------------[ cut here ]------------
[    4.111667@0] WARNING: at kernel/smp.c:320 smp_call_function_single+0x118/0x1d4()
[    4.119126@0] Modules linked in:
[    4.122347@0] [<c004591c>] (unwind_backtrace+0x0/0x10c) from [<c00668c8>] (warn_slowpath_common+0x54/0x64)
[    4.131980@0] [<c00668c8>] (warn_slowpath_common+0x54/0x64) from [<c00668f4>] (warn_slowpath_null+0x1c/0x24)
[    4.141788@0] [<c00668f4>] (warn_slowpath_null+0x1c/0x24) from [<c0098a08>] (smp_call_function_single+0x118/0x1d4)
[    4.152116@0] [<c0098a08>] (smp_call_function_single+0x118/0x1d4) from [<c0098d80>] (smp_call_function+0x38/0x68)
[    4.162358@0] [<c0098d80>] (smp_call_function+0x38/0x68) from [<c004da48>] (clk_set_rate_a9+0x90/0xd8)
[    4.171649@0] [<c004da48>] (clk_set_rate_a9+0x90/0xd8) from [<c004ca54>] (meson_clk_set_rate+0x1bc/0x1fc)
[    4.181196@0] [<c004ca54>] (meson_clk_set_rate+0x1bc/0x1fc) from [<c004cb28>] (clk_set_rate+0x94/0xbc)
[    4.190484@0] [<c004cb28>] (clk_set_rate+0x94/0xbc) from [<c0056c90>] (meson_cpufreq_target_locked+0x124/0x214)
[    4.200552@0] [<c0056c90>] (meson_cpufreq_target_locked+0x124/0x214) from [<c0056dac>] (meson_cpufreq_target+0x2c/0x44)
[    4.211316@0] [<c0056dac>] (meson_cpufreq_target+0x2c/0x44) from [<c0472e00>] (__cpufreq_driver_target+0x5c/0x60)
[    4.221558@0] [<c0472e00>] (__cpufreq_driver_target+0x5c/0x60) from [<c04756ac>] (cpufreq_governor_performance+0x28/0x30)
[    4.232495@0] [<c04756ac>] (cpufreq_governor_performance+0x28/0x30) from [<c0472fcc>] (__cpufreq_governor+0xc0/0x138)
[    4.243083@0] [<c0472fcc>] (__cpufreq_governor+0xc0/0x138) from [<c0473168>] (__cpufreq_set_policy+0x124/0x160)
[    4.253152@0] [<c0473168>] (__cpufreq_set_policy+0x124/0x160) from [<c047430c>] (cpufreq_add_dev_interface+0x2d0/0x320)
[    4.263916@0] [<c047430c>] (cpufreq_add_dev_interface+0x2d0/0x320) from [<c0474718>] (cpufreq_add_dev+0x3bc/0x4d0)
[    4.274246@0] [<c0474718>] (cpufreq_add_dev+0x3bc/0x4d0) from [<c03a7820>] (sysdev_driver_register+0xc4/0x14c)
[    4.284227@0] [<c03a7820>] (sysdev_driver_register+0xc4/0x14c) from [<c0473840>] (cpufreq_register_driver+0x84/0x1fc)
[    4.294818@0] [<c0473840>] (cpufreq_register_driver+0x84/0x1fc) from [<c03aa440>] (platform_drv_probe+0x14/0x18)
[    4.304973@0] [<c03aa440>] (platform_drv_probe+0x14/0x18) from [<c03a8f3c>] (driver_probe_device+0x7c/0x184)
[    4.314780@0] [<c03a8f3c>] (driver_probe_device+0x7c/0x184) from [<c03a90d0>] (__driver_attach+0x8c/0x90)
[    4.324328@0] [<c03a90d0>] (__driver_attach+0x8c/0x90) from [<c03a870c>] (bus_for_each_dev+0x5c/0x98)
[    4.333528@0] [<c03a870c>] (bus_for_each_dev+0x5c/0x98) from [<c03a8004>] (bus_add_driver+0x1e0/0x2b4)
[    4.342816@0] [<c03a8004>] (bus_add_driver+0x1e0/0x2b4) from [<c03a96a4>] (driver_register+0x78/0x18c)
[    4.352105@0] [<c03a96a4>] (driver_register+0x78/0x18c) from [<c03aa8ec>] (platform_driver_probe+0x18/0xa0)
[    4.361828@0] [<c03aa8ec>] (platform_driver_probe+0x18/0xa0) from [<c00375b8>] (do_one_initcall+0x34/0x170)
[    4.371548@0] [<c00375b8>] (do_one_initcall+0x34/0x170) from [<c00083dc>] (kernel_init+0xa8/0x13c)
[    4.380488@0] [<c00083dc>] (kernel_init+0xa8/0x13c) from [<c003ed00>] (kernel_thread_exit+0x0/0x8)
[    4.389423@0] ---[ end trace 0d6171e9dd60f810 ]---
[    4.396768@0] dwc_otg_pcd_pullup is_on=0
[    4.398115@0] WARN::dwc_otg_handle_mode_mismatch_intr:68: Mode Mismatch Interrupt: currently in Host mode
[    4.398118@0] 
[    4.409324@0] WARN::dwc_otg_handle_mode_mismatch_intr:68: Mode Mismatch Interrupt: currently in Host mode
[    4.409328@0] 
[    4.423180@1] hub 1-1:1.0: USB hub found
[    4.424732@1] hub 1-1:1.0: 4 ports detected
[    4.429087@0] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    4.435641@0] android_usb gadget: Number of LUNs=2
[    4.440387@0]  lun0: LUN: removable file: (no medium)
[    4.445437@0]  lun1: LUN: removable file: (no medium)
[    4.450965@0] android_usb gadget: android_usb ready
[    4.455758@0] aml_rtc aml_rtc: setting system clock to 1970-01-01 11:06:21 UTC (39981)
[    4.463494@1] Indeed it is in host mode hprt0 = 00021501
[    4.481003@0] Changing baud from 0 to 115200
[    4.501149@0] yaffs: dev is 32505858 name is "mtdblock2" rw
[    4.501175@0] yaffs: passed flags ""
[    4.515566@0] nand communication have uncorrectable ecc error 0
[    4.515926@0] aml nand read data ecc plane0 failed at page 23040 chip 0
[    4.522665@0] nand communication have uncorrectable ecc error 0
[    4.528430@0] aml nand read data ecc plane1 failed at page 23040 chip 0
[    4.549803@0] VFS: Mounted root (yaffs2 filesystem) on device 31:2.
[    4.554996@0] devtmpfs: mounted
[    4.555053@0] Freeing init memory: 188K
[    4.601213@0] sd_mmc_info->card_type=0
[    4.601234@0] begin SDIO check ......
[    4.625637@0] sdio_timeout_int_times = 0; timeout = 498
[    4.641083@1] usb 2-1: new high speed USB device number 2 using dwc_otg
[    4.642416@0] Indeed it is in host mode hprt0 = 00001101
[    4.648261@0] sdio_timeout_int_times = 0; timeout = 498
[    4.652663@0] SEND OP timeout @1
[    4.661268@0] begin SD&SDHC check ......
[    4.703651@0] sdio_timeout_int_times = 0; timeout = 498
[    4.703687@0] SEND IF timeout @2
[    4.729350@0] sdio_timeout_int_times = 0; timeout = 498
[    4.729396@0] begin MMC check ......
[    4.773644@0] sdio_timeout_int_times = 0; timeout = 498
[    4.773681@0] No any SD/MMC card detected!
[    4.777414@0] #SD_MMC_ERROR_DRIVER_FAILURE error occured in sd_voltage_validation()
[    4.786573@0] 
[    4.786579@0] SD/MMC initialization started......
[    4.831853@0] yaffs: dev is 32505859 name is "mtdblock3" rw
[    4.831883@0] yaffs: passed flags ""
[    4.853516@0] hub 2-1:1.0: USB hub found
[    4.853835@0] hub 2-1:1.0: 4 ports detected
[    4.931616@1] usb 1-1.2: new low speed USB device number 3 using dwc_otg
2880+0 records in
2880+0 records out
3686400 bytes (3.5MB) copied, 0.007446 seconds, 472.1MB/s
dd: writing '/dev/fb1': No space left on device
821+0 records in
819+1 records out
1048576 bytes (1.0MB) copied, 0.002304 seconds, 434.0MB/s
fbset: FBIOPUT_VSCREENINFO: Cannot allocate memory
[    5.041884@0] usb 1-1.2: device descriptor read/all, error -32
chown: unknown user/group default:default
S10setup: init fb0, fb1
S10setup: remount / rw
S10setup: checking keys
S10setup: moving /etc
[    5.121406@0] usb 1-1.2: new low speed USB device number 4 using dwc_otg
S10setup: moving /media
S10setup: mounting /tmp/userdata
cat: can't open '/sys/devices/virtual/mtd/mtd0/name': No such file or directory
[    5.222707@0] usb 1-1.2: device descriptor read/all, error -32
cat: can't open '/sys/devices/virtual/mtd/mtd1/name': No such file or directory
[    5.235212@0] sd_mmc_info->card_type=0
[    5.238757@0] begin SDIO check ......
cat: can't open '/sys/devices/virtual/mtd/mtd2/name': No such file or directory
cat: can't open '/sys/devices/virtual/mtd/mtd3/name': No such file or directory
cat: can't open '/sys/devices/virtual/mtd/mtd4/name': No such file or directory
[    5.265500@0] sdio_timeout_int_times = 0; timeout = 498
cat: can't open '/sys/devices/virtual/mtd/mtd5/name': No such file or directory
mount: can't find /tmp/userdata in /etc/fstab
S10setup: remount / ro
S10setup: switching to ondemand
S10setup: done
[    5.291311@0] sdio_timeout_int_times = 0; timeout = 497
[    5.294051@0] SEND OP timeout @1
Populating  using udev: [    5.297441@0] begin SD&SDHC check ......
[    5.311481@0] usb 1-1.2: new low speed USB device number 5 using dwc_otg
udevd[1482]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'

[    5.333095@0] usb 1-1.2: unable to read config index 0 descriptor/start: -32
[    5.334598@0] usb 1-1.2: chopping to 0 config(s)
[    5.339982@0] usb 1-1.2: string descriptor 0 read error: -32
done[    5.345033@0] sdio_timeout_int_times = 0; timeout = 498

[    5.350512@0] SEND IF timeout @2
Initializing coldplug devices[    5.354635@0] usb 1-1.2: no configuration chosen from 0 choices
[    5.357117@1] udevd[1483]: starting version 173

[    5.389630@0] sdio_timeout_int_times = 0; timeout = 498
[    5.389670@0] begin MMC check ......
[    5.433900@0] sdio_timeout_int_times = 0; timeout = 498
[    5.433962@0] No any SD/MMC card detected!
[    5.437688@0] #SD_MMC_ERROR_DRIVER_FAILURE error occured in sd_voltage_validation()
[    5.471132@0] 
[    5.471147@0] SD/MMC initialization started......
done
Initializing random number generator... done.
System time was Thu Jan  1 11:06:22 UTC 1970.
Setting the System Clock using the Hardware Clock as reference...
[    5.911278@1] sd_mmc_info->card_type=0
[    5.914900@1] begin SDIO check ......
[    5.941144@1] sdio_timeout_int_times = 0; timeout = 497
[    5.963793@1] sdio_timeout_int_times = 0; timeout = 498
[    5.963840@1] SEND OP timeout @1
[    5.966895@1] begin SD&SDHC check ......
[    6.003691@1] sdio_timeout_int_times = 0; timeout = 498
[    6.003737@1] SEND IF timeout @2
[    6.029389@1] sdio_timeout_int_times = 0; timeout = 498
[    6.029435@1] begin MMC check ......
[    6.073789@0] sdio_timeout_int_times = 0; timeout = 498
[    6.073838@0] No any SD/MMC card detected!
[    6.077565@0] #SD_MMC_ERROR_DRIVER_FAILURE error occured in sd_voltage_validation()
[    6.471377@0] set voltage to 1007000; selector=12
[    9.504587@0] === key 116 down ===
hwclock: select() to /dev/rtc0 to wait for clock tick timed out: No such file or directory
System Clock set. System local time is now Thu Jan  1 11:06:27 UTC 1970.
Starting system message bus: done
Starting network...
net.core.rmem_max = 33554432
net.core.netdev_max_backlog = 2000
net.ipv4.udp_mem = 262144 327680 393216
net.ipv4.tcp_mem = 262144 327680 393216
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
Getting initial time via ntp.
Starting network time protocol daemon: ntpd.
[   11.671147@0] set voltage to 1283000; selector=1
Starting dropbear sshd: generating rsa key... generating dsa key... OK
Starting mali...
[   12.338564@0] UMP: UMP device driver  loaded
[   12.359951@0] Mali<2>: 
[   12.360002@0] Mali<2>: Inserting Mali v14 device driver. 
[   12.362693@0] Mali<2>: Compiled: Mar 21 2013, time: 18:29:11.
[   12.367965@0] Mali<2>: Driver revision: 
[   12.372319@0] mail version=-1
[   12.425291@0] mali_meson_rev_detect: No interrupt received.
[   12.475642@0] set voltage to 1207000; selector=4
[   12.475900@0] mali_meson_rev_detect: Mali Rev B detected.
[   12.480110@0] Mali pp1 MMU register mapped at e001e000...
[   12.485497@0] Mali pp2 MMU register mapped at e00d0000...
[   12.490858@0] mail version=1
[   12.493725@0] Mali<2>: Memory system initializing
[   12.498402@0] Mali<2>: Mali OS memory allocator created with max allocation size of 0x20000000 bytes, cpu_usage_adjust 0x00000000
[   12.510047@0] Mali<2>: Memory Validator 'Framebuffer' installed for Mali physical address base=0x84000000, size=0x12000000
[   12.521165@0] mail version=1
[   12.523928@0] Mali pp1 MMU register mapped at e00d2000...
[   12.529310@0] Mali pp2 MMU register mapped at e00d4000...
[   12.534705@0] Mali<2>: Mali PP: Creating Mali PP core: Mali-400 PP 0
[   12.541030@0] Mali<2>: Mali PP: Base address of PP core: 0xd0068000
[   12.547331@0] Mali<2>: Found Mali GPU Mali-400 MP r1p0
[   12.553399@0] Mali<2>: Mali L2 cache: Creating Mali L2 cache: Mali-400 L2 cache
[   12.559702@0] Mali<2>: Mali MMU: Creating Mali MMU: Mali-400 MMU for GP
[   12.566305@0] Mali<2>: Mali GP: Creating Mali GP core: Mali-400 GP
[   12.572471@0] Mali<2>: Mali MMU: Creating Mali MMU: Mali-400 MMU for PP 0
[   12.579238@0] Mali<2>: Mali PP: Creating Mali PP core: Mali-400 PP 0
[   12.585548@0] Mali<2>: Mali PP: Base address of PP core: 0xd0068000
[   12.591821@0] Mali<2>: Mali MMU: Creating Mali MMU: Mali-400 MMU for PP 1
[   12.598584@0] Mali<2>: Mali PP: Creating Mali PP core: Mali-400 PP 1
[   12.604921@0] Mali<2>: Mali PP: Base address of PP core: 0xd006a000
[   12.612594@0] Mali: Mali device driver loaded
Starting XBMC...
Can't open /dev/amremote .
[   12.671458@0] set voltage to 1107000; selector=8
[   12.871545@0] set voltage to 1032000; selector=11
[   13.071528@0] set voltage to 1007000; selector=12
[   13.671230@0] set voltage to 1283000; selector=1
[   13.871365@0] set voltage to 1107000; selector=8
[   14.071462@0] set voltage to 1032000; selector=11
[   15.071324@0] set voltage to 1007000; selector=12
[   25.271648@0] set voltage to 1283000; selector=1
[   25.391782@1] buf=0
[   25.391806@1] IEC958_mode_raw=0
[   25.471350@0] set voltage to 1207000; selector=4
[   25.671147@0] set voltage to 1283000; selector=1
[   26.071297@0] set voltage to 1007000; selector=12
[   26.436659@1] Mali<2>: Session starting
[   26.437463@1] Mali<2>: Session has ended
ERROR: Unable to create GUI. Exiting
[   26.671140@0] set voltage to 1283000; selector=1
[   26.871339@0] set voltage to 1007000; selector=12
Segmentation fault
XBMC crashed with exit code 139.  Respawning..