jeanfbrito/printer.cfg

## printer.cfg
# This file is an example config file for cartesian style printers.
# One may copy and edit this file to configure a new cartesian
# printer.

# DO NOT COPY THIS FILE WITHOUT CAREFULLY READING AND UPDATING IT
# FIRST. Incorrectly configured parameters may cause damage.

# See docs/Config_Reference.md for a description of parameters.

#####################################################################
# 	X/Y Stepper Settings
#####################################################################

[stepper_x]
step_pin: P2.2
dir_pin: P2.6
enable_pin: !P2.1
rotation_distance: 40
full_steps_per_rotation:200
endstop_pin: !P1.29
position_min: -7
position_endstop: -7
position_max: 295
homing_speed: 50
homing_retract_dist: 5
microsteps: 16

[tmc2209 stepper_x]
uart_pin: P1.10
#interpolate: True
run_current: 0.7
#hold_current: 0.5

[stepper_y]
step_pin: P0.19
dir_pin: P0.20
enable_pin: !P2.8
rotation_distance: 40
full_steps_per_rotation:200
endstop_pin: !P1.28
position_min: -25
position_endstop: -25
position_max: 270
homing_speed: 50
homing_retract_dist: 5
microsteps: 16

[tmc2209 stepper_y]
uart_pin: P1.9
#interpolate: True
run_current: 0.8
#hold_current: 0.5

[stepper_z]
step_pin: P0.22
dir_pin: !P2.11
enable_pin: !P0.21
rotation_distance: 8
endstop_pin: !P1.27
position_endstop: 0.0
position_max: 300
position_min: -3
homing_speed: 5.0
second_homing_speed: 2
homing_retract_dist: 5
microsteps: 16

[stepper_z1]
step_pin: P1.15
dir_pin: !P1.14
enable_pin: !P1.16
microsteps: 16
rotation_distance: 8
endstop_pin: !P1.25


[tmc2209 stepper_z]
uart_pin: P1.8
#interpolate: True
run_current: 0.8
#hold_current: 0.5

[tmc2209 stepper_z1]
uart_pin: P1.1
#interpolate: True
run_current: 0.8
#hold_current: 0.5

#####################################################################
# 	Extruder
#####################################################################

#	E0 on MCU
[extruder]
step_pin: P2.13
dir_pin: !P0.11
enable_pin: !P2.12
##	Update value below when you perform extruder calibration
##	If you ask for 100mm of filament, but in reality it is 98mm:
##	rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
##  22.6789511 is a good starting point
rotation_distance: 22.6789511	#Bondtech 5mm Drive Gears
##	Update Gear Ratio depending on your Extruder Type
##	Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
##	Use 80:20 for M4, M3.1
gear_ratio: 50:17				#BMG Gear Ratio
#rotation_distance: 29.5
microsteps: 16
full_steps_per_rotation: 200	#200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.4
filament_diameter: 1.75
max_extrude_only_distance: 220.0
heater_pin: P2.7
##	Validate the following thermistor type to make sure it is correct
sensor_type: ATC Semitec 104GT-2
#sensor_type: NTC 100K beta 3950
sensor_pin: P0.24
min_temp: 0
max_temp: 270
max_power: 1.0
min_extrude_temp: 160
max_extrude_only_velocity: 75.0
max_extrude_only_accel: 1000.0
##	Try to keep pressure_advance below 1.0

#pressure_advance: 0.11
##	Default is 0.040, leave stock
#pressure_advance_smooth_time: 0.040
#control: pid
#pid_Kp=28.278
#pid_Ki=1.746
#pid_Kd=114.528

##	E0 on MCU X/Y
##	Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 extruder]
uart_pin: P1.4
interpolate: false
run_current: 0.5
#hold_current: 0.3

[fan]
##	Print Cooling Fan - XYE board, Fan Pin
pin: P2.3
kick_start_time: 3.5
##	Depending on your fan, you may need to increase this value
##	if your fan will not start. Can change cycle_time (increase)
##	if your fan is not able to slow down effectively
off_below: 0.10

[bltouch]
sensor_pin: P0.10
control_pin: P2.0
pin_up_touch_mode_reports_triggered: False
samples: 3
#x_offset: 68
x_offset: 46
#x_offset: -51
y_offset: 0
#y_offset: -24.8
#z_offset: 0.7

[bed_mesh]
speed: 120
horizontal_move_z: 5
mesh_min: 50,10
mesh_max: 290, 270
probe_count: 6,6

[bed_screws]
screw1: 5,30
screw2: 285,30
screw3: 285,245
screw4: 5,245

#####################################################################
# 	Bed Heater
#####################################################################

[heater_bed]
heater_pin: P2.5
#sensor_type: NTC 100K beta 3950
sensor_type: EPCOS 100K B57560G104F
sensor_pin: P0.25
##	Adjust Max Power so your heater doesn't warp your bed
max_power: 1.0
min_temp: 0
max_temp: 120
#control: pid
#pid_Kp=76.304
#pid_Ki=1.657
#pid_Kd=878.444

[display]
#	mini12864 LCD Display
lcd_type: uc1701
cs_pin: P1.18
a0_pin: P1.19
encoder_pins: ^P3.25,^P3.26
click_pin: ^!P0.28
contrast: 63

[mcu]
serial: /dev/serial/by-id/usb-Klipper_lpc1769_16200018C09869AF9BF6405EC22000F5-if00

[printer]
kinematics: cartesian
max_velocity: 150
max_accel: 3000
#max_accel: 1500
#max_accel_to_decel: 1500
#max_z_velocity: 15
max_z_velocity: 5
max_z_accel: 30
square_corner_velocity: 5.0

[input_shaper]
shaper_freq_x: 28.2
shaper_freq_y: 23
shaper_type: mzv

#[mcu rpi]
#serial: /tmp/klipper_host_mcu

#[adxl345]
#cs_pin: rpi:None

#[resonance_tester]
#accel_chip: adxl345
#probe_points:
#    150, 150, 20  # an example

######################################################################
# Filament Change
######################################################################

# M600: Filament Change. This macro will pause the printer, move the
# tool to the change position, and retract the filament 50mm. Adjust
# the retraction settings for your own extruder. After filament has
# been changed, the print can be resumed from its previous position
# with the "RESUME" gcode.

# Pressure Advance test macro by drawing 20 simple lines
#
# Adapted from: https://www.reddit.com/r/VORONDesign/comments/sjdiol/pressure_advance_testing_macro_klipper/
# to suit home-made free ABL that requires a pause after homing to manually retract the probe.
#
# To do that, the process is divided into 2 macros:
#
# - PA_INIT to bring bed and extruder up to temperature, then home.
#   eg. PA_INIT BED_TEMP=65 EXTRUDER_TEMP=205
#   After homing, the ABL can be manually retracted
#
# - PA_CAL to start the Pressure Advance test.
#   eg. PA_CAL PA_START=0.01 PA_STEP=0.01 NZL=0.4
#   This will draw 20 lines using different PA values
#
# To use, simply include in printer.cfg:
#
#   [include pa_macro.cfg]

[gcode_macro PA_INIT]
gcode:
  {% set BED_TEMP = params.BED_TEMP|default(60)|float %}
  {% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(190)|float %}
  M140 S{BED_TEMP} ;Start heating bed
  M190 S{BED_TEMP} ;Wait for bed to reach temp before proceeding
  M104 S{EXTRUDER_TEMP} ;Start heating extruder
  M109 S{EXTRUDER_TEMP} ;Wait for extruder to reach temp before proceeding
  G28 ;Home all axes and pause with audio alert

[gcode_macro PA_CAL]
gcode:
  {% set PA_START = params.PA_START|default(0.0)|float %}
  {% set PA_STEP = params.PA_STEP|default(0.005)|float %}
  {% set NZL_CFG = printer.configfile.config["extruder"]["nozzle_diameter"]|float %}
  {% set NZL = params.NZL|default(NZL_CFG)|float %}
  {% set E5 = (0.1147475 * NZL) * 5|float %}
  {% set E20 = (0.1147475 * NZL) * 20|float %}
  {% set E40 = (0.1147475 * NZL) * 40|float %}
  {% set X_MID = printer.configfile.config["stepper_x"]["position_max"]|float / 2.0 %}
  {% set Y_MID = printer.configfile.config["stepper_y"]["position_max"]|float / 2.0 %}

  G21                                             ; millimeter units
  G90                                             ; absolute XYZ
  M83                                             ; relative E
  SET_VELOCITY_LIMIT ACCEL=3000 ACCEL_TO_DECEL=1500
  G92 E0                                          ; reset extruder
  M106 S0                                         ; set fan speed to zero

  ; This was taken from Cura to prime the extruder by tracing a line at the
	; left side of the build bed twice
  G1 X10.1 Y20 Z0.28 F5000.0                      ; move to start position
  G1 X10.1 Y200.0 Z0.28 F1500.0 E15               ; draw the first line
  G1 X10.4 Y200.0 Z0.28 F5000.0                   ; move to side a little
  G1 X10.4 Y20 Z0.28 F1500.0 E30                  ; draw the second line
  G1 E-2 F1800                                    ; retract
  G1 Z5 F300                                      ; move above layer height

  {% for i in range(0, 20) %}
    SET_PRESSURE_ADVANCE ADVANCE={PA_START + (i * PA_STEP)} ; set Pressure Advance
    M117 Testing Pressure Advance at: {PA_START + (i * PA_STEP)}
    G1 X{(X_MID-40)} Y{(Y_MID-35)+(5*i)} F5000         ; move to start position
    G1 Z0.2 F300                                       ; move to layer height
    G1 E2 F1800                                        ; un-retract
    G1 X{(X_MID-20)} Y{(Y_MID-35)+(5*i)} E{E20} F300   ; print line part one
    G1 X{(X_MID+20)} Y{(Y_MID-35)+(5*i)} E{E40} F9000  ; print line part two
    G1 X{(X_MID+40)} Y{(Y_MID-35)+(5*i)} E{E20} F300   ; print line part three
    G1 E-2 F1800                                       ; retract
    G1 Z5 F300                                         ; move above layer height
  {% endfor %}

	; This was again taken from Cura to raise the extruder and push the build plate forward when test is done
  G1 Z20 F300                                          ; Raise Z more
  G1 X{X_MID} Y{(Y_MID-35)+(5*24)} F300                ; Present print by pushing build plate forward a little

  M117 Find best line and multiply it by ({PA_START} + (line * {PA_STEP}) ) to find your PA setting.

[pause_resume]

[gcode_macro M600]
gcode:
    {% set X = params.X|default(50)|float %}
    {% set Y = params.Y|default(0)|float %}
    {% set Z = params.Z|default(10)|float %}
    SAVE_GCODE_STATE NAME=M600_state
    PAUSE
    G91
    G1 E-.8 F2700
    G1 Z{Z}
    G90
    G1 X{X} Y{Y} F3000
    G91
    G1 E-50 F1000
    M18 E
    RESTORE_GCODE_STATE NAME=M600_state

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 31.911
#*# pid_ki = 2.149
#*# pid_kd = 118.471
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  -0.100000, -0.126667, -0.114167, -0.063333, -0.053333, -0.046667
#*# 	  -0.065833, -0.093333, -0.087500, -0.087500, -0.075833, -0.095833
#*# 	  -0.057500, -0.081667, -0.130833, -0.113333, -0.115833, -0.108333
#*# 	  -0.075833, -0.088333, -0.116667, -0.102500, -0.096667, -0.102500
#*# 	  -0.134167, -0.137500, -0.130000, -0.110000, -0.093333, -0.054167
#*# 	  -0.126667, -0.116667, -0.106667, -0.061667, 0.009167, 0.051667
#*# tension = 0.2
#*# min_x = 50.0
#*# algo = lagrange
#*# y_count = 6
#*# mesh_y_pps = 2
#*# min_y = 10.0
#*# x_count = 6
#*# max_y = 270.0
#*# mesh_x_pps = 2
#*# max_x = 290.0
#*#
#*# [bltouch]
#*# z_offset = 2.100
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 75.650
#*# pid_ki = 1.005
#*# pid_kd = 1424.118
	# This file is an example config file for cartesian style printers.
	# One may copy and edit this file to configure a new cartesian
	# printer.

	# DO NOT COPY THIS FILE WITHOUT CAREFULLY READING AND UPDATING IT
	# FIRST. Incorrectly configured parameters may cause damage.

	# See docs/Config_Reference.md for a description of parameters.

	#####################################################################
	# X/Y Stepper Settings
	#####################################################################

	[stepper_x]
	step_pin: P2.2
	dir_pin: P2.6
	enable_pin: !P2.1
	rotation_distance: 40
	full_steps_per_rotation:200
	endstop_pin: !P1.29
	position_min: -7
	position_endstop: -7
	position_max: 295
	homing_speed: 50
	homing_retract_dist: 5
	microsteps: 16

	[tmc2209 stepper_x]
	uart_pin: P1.10
	#interpolate: True
	run_current: 0.7
	#hold_current: 0.5

	[stepper_y]
	step_pin: P0.19
	dir_pin: P0.20
	enable_pin: !P2.8
	rotation_distance: 40
	full_steps_per_rotation:200
	endstop_pin: !P1.28
	position_min: -25
	position_endstop: -25
	position_max: 270
	homing_speed: 50
	homing_retract_dist: 5
	microsteps: 16

	[tmc2209 stepper_y]
	uart_pin: P1.9
	#interpolate: True
	run_current: 0.8
	#hold_current: 0.5

	[stepper_z]
	step_pin: P0.22
	dir_pin: !P2.11
	enable_pin: !P0.21
	rotation_distance: 8
	endstop_pin: !P1.27
	position_endstop: 0.0
	position_max: 300
	position_min: -3
	homing_speed: 5.0
	second_homing_speed: 2
	homing_retract_dist: 5
	microsteps: 16

	[stepper_z1]
	step_pin: P1.15
	dir_pin: !P1.14
	enable_pin: !P1.16
	microsteps: 16
	rotation_distance: 8
	endstop_pin: !P1.25


	[tmc2209 stepper_z]
	uart_pin: P1.8
	#interpolate: True
	run_current: 0.8
	#hold_current: 0.5

	[tmc2209 stepper_z1]
	uart_pin: P1.1
	#interpolate: True
	run_current: 0.8
	#hold_current: 0.5

	#####################################################################
	# Extruder
	#####################################################################

	# E0 on MCU
	[extruder]
	step_pin: P2.13
	dir_pin: !P0.11
	enable_pin: !P2.12
	## Update value below when you perform extruder calibration
	## If you ask for 100mm of filament, but in reality it is 98mm:
	## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
	## 22.6789511 is a good starting point
	rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
	## Update Gear Ratio depending on your Extruder Type
	## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
	## Use 80:20 for M4, M3.1
	gear_ratio: 50:17 #BMG Gear Ratio
	#rotation_distance: 29.5
	microsteps: 16
	full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
	nozzle_diameter: 0.4
	filament_diameter: 1.75
	max_extrude_only_distance: 220.0
	heater_pin: P2.7
	## Validate the following thermistor type to make sure it is correct
	sensor_type: ATC Semitec 104GT-2
	#sensor_type: NTC 100K beta 3950
	sensor_pin: P0.24
	min_temp: 0
	max_temp: 270
	max_power: 1.0
	min_extrude_temp: 160
	max_extrude_only_velocity: 75.0
	max_extrude_only_accel: 1000.0
	## Try to keep pressure_advance below 1.0

	#pressure_advance: 0.11
	## Default is 0.040, leave stock
	#pressure_advance_smooth_time: 0.040
	#control: pid
	#pid_Kp=28.278
	#pid_Ki=1.746
	#pid_Kd=114.528

	## E0 on MCU X/Y
	## Make sure to update below for your relevant driver (2208 or 2209)
	[tmc2209 extruder]
	uart_pin: P1.4
	interpolate: false
	run_current: 0.5
	#hold_current: 0.3

	[fan]
	## Print Cooling Fan - XYE board, Fan Pin
	pin: P2.3
	kick_start_time: 3.5
	## Depending on your fan, you may need to increase this value
	## if your fan will not start. Can change cycle_time (increase)
	## if your fan is not able to slow down effectively
	off_below: 0.10

	[bltouch]
	sensor_pin: P0.10
	control_pin: P2.0
	pin_up_touch_mode_reports_triggered: False
	samples: 3
	#x_offset: 68
	x_offset: 46
	#x_offset: -51
	y_offset: 0
	#y_offset: -24.8
	#z_offset: 0.7

	[bed_mesh]
	speed: 120
	horizontal_move_z: 5
	mesh_min: 50,10
	mesh_max: 290, 270
	probe_count: 6,6

	[bed_screws]
	screw1: 5,30
	screw2: 285,30
	screw3: 285,245
	screw4: 5,245

	#####################################################################
	# Bed Heater
	#####################################################################

	[heater_bed]
	heater_pin: P2.5
	#sensor_type: NTC 100K beta 3950
	sensor_type: EPCOS 100K B57560G104F
	sensor_pin: P0.25
	## Adjust Max Power so your heater doesn't warp your bed
	max_power: 1.0
	min_temp: 0
	max_temp: 120
	#control: pid
	#pid_Kp=76.304
	#pid_Ki=1.657
	#pid_Kd=878.444

	[display]
	# mini12864 LCD Display
	lcd_type: uc1701
	cs_pin: P1.18
	a0_pin: P1.19
	encoder_pins: ^P3.25,^P3.26
	click_pin: ^!P0.28
	contrast: 63

	[mcu]
	serial: /dev/serial/by-id/usb-Klipper_lpc1769_16200018C09869AF9BF6405EC22000F5-if00

	[printer]
	kinematics: cartesian
	max_velocity: 150
	max_accel: 3000
	#max_accel: 1500
	#max_accel_to_decel: 1500
	#max_z_velocity: 15
	max_z_velocity: 5
	max_z_accel: 30
	square_corner_velocity: 5.0

	[input_shaper]
	shaper_freq_x: 28.2
	shaper_freq_y: 23
	shaper_type: mzv

	#[mcu rpi]
	#serial: /tmp/klipper_host_mcu

	#[adxl345]
	#cs_pin: rpi:None

	#[resonance_tester]
	#accel_chip: adxl345
	#probe_points:
	# 150, 150, 20 # an example

	######################################################################
	# Filament Change
	######################################################################

	# M600: Filament Change. This macro will pause the printer, move the
	# tool to the change position, and retract the filament 50mm. Adjust
	# the retraction settings for your own extruder. After filament has
	# been changed, the print can be resumed from its previous position
	# with the "RESUME" gcode.

	# Pressure Advance test macro by drawing 20 simple lines
	#
	# Adapted from: https://www.reddit.com/r/VORONDesign/comments/sjdiol/pressure_advance_testing_macro_klipper/
	# to suit home-made free ABL that requires a pause after homing to manually retract the probe.
	#
	# To do that, the process is divided into 2 macros:
	#
	# - PA_INIT to bring bed and extruder up to temperature, then home.
	# eg. PA_INIT BED_TEMP=65 EXTRUDER_TEMP=205
	# After homing, the ABL can be manually retracted
	#
	# - PA_CAL to start the Pressure Advance test.
	# eg. PA_CAL PA_START=0.01 PA_STEP=0.01 NZL=0.4
	# This will draw 20 lines using different PA values
	#
	# To use, simply include in printer.cfg:
	#
	# [include pa_macro.cfg]

	[gcode_macro PA_INIT]
	gcode:
	{% set BED_TEMP = params.BED_TEMP\|default(60)\|float %}
	{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP\|default(190)\|float %}
	M140 S{BED_TEMP} ;Start heating bed
	M190 S{BED_TEMP} ;Wait for bed to reach temp before proceeding
	M104 S{EXTRUDER_TEMP} ;Start heating extruder
	M109 S{EXTRUDER_TEMP} ;Wait for extruder to reach temp before proceeding
	G28 ;Home all axes and pause with audio alert

	[gcode_macro PA_CAL]
	gcode:
	{% set PA_START = params.PA_START\|default(0.0)\|float %}
	{% set PA_STEP = params.PA_STEP\|default(0.005)\|float %}
	{% set NZL_CFG = printer.configfile.config["extruder"]["nozzle_diameter"]\|float %}
	{% set NZL = params.NZL\|default(NZL_CFG)\|float %}
	{% set E5 = (0.1147475 * NZL) * 5\|float %}
	{% set E20 = (0.1147475 * NZL) * 20\|float %}
	{% set E40 = (0.1147475 * NZL) * 40\|float %}
	{% set X_MID = printer.configfile.config["stepper_x"]["position_max"]\|float / 2.0 %}
	{% set Y_MID = printer.configfile.config["stepper_y"]["position_max"]\|float / 2.0 %}

	G21 ; millimeter units
	G90 ; absolute XYZ
	M83 ; relative E
	SET_VELOCITY_LIMIT ACCEL=3000 ACCEL_TO_DECEL=1500
	G92 E0 ; reset extruder
	M106 S0 ; set fan speed to zero

	; This was taken from Cura to prime the extruder by tracing a line at the
	; left side of the build bed twice
	G1 X10.1 Y20 Z0.28 F5000.0 ; move to start position
	G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ; draw the first line
	G1 X10.4 Y200.0 Z0.28 F5000.0 ; move to side a little
	G1 X10.4 Y20 Z0.28 F1500.0 E30 ; draw the second line
	G1 E-2 F1800 ; retract
	G1 Z5 F300 ; move above layer height

	{% for i in range(0, 20) %}
	SET_PRESSURE_ADVANCE ADVANCE={PA_START + (i * PA_STEP)} ; set Pressure Advance
	M117 Testing Pressure Advance at: {PA_START + (i * PA_STEP)}
	G1 X{(X_MID-40)} Y{(Y_MID-35)+(5*i)} F5000 ; move to start position
	G1 Z0.2 F300 ; move to layer height
	G1 E2 F1800 ; un-retract
	G1 X{(X_MID-20)} Y{(Y_MID-35)+(5*i)} E{E20} F300 ; print line part one
	G1 X{(X_MID+20)} Y{(Y_MID-35)+(5*i)} E{E40} F9000 ; print line part two
	G1 X{(X_MID+40)} Y{(Y_MID-35)+(5*i)} E{E20} F300 ; print line part three
	G1 E-2 F1800 ; retract
	G1 Z5 F300 ; move above layer height
	{% endfor %}

	; This was again taken from Cura to raise the extruder and push the build plate forward when test is done
	G1 Z20 F300 ; Raise Z more
	G1 X{X_MID} Y{(Y_MID-35)+(5*24)} F300 ; Present print by pushing build plate forward a little

	M117 Find best line and multiply it by ({PA_START} + (line * {PA_STEP}) ) to find your PA setting.

	[pause_resume]

	[gcode_macro M600]
	gcode:
	{% set X = params.X\|default(50)\|float %}
	{% set Y = params.Y\|default(0)\|float %}
	{% set Z = params.Z\|default(10)\|float %}
	SAVE_GCODE_STATE NAME=M600_state
	PAUSE
	G91
	G1 E-.8 F2700
	G1 Z{Z}
	G90
	G1 X{X} Y{Y} F3000
	G91
	G1 E-50 F1000
	M18 E
	RESTORE_GCODE_STATE NAME=M600_state

	#*# <---------------------- SAVE_CONFIG ---------------------->
	#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
	#*#
	#*# [extruder]
	#*# control = pid
	#*# pid_kp = 31.911
	#*# pid_ki = 2.149
	#*# pid_kd = 118.471
	#*#
	#*# [bed_mesh default]
	#*# version = 1
	#*# points =
	#*# -0.100000, -0.126667, -0.114167, -0.063333, -0.053333, -0.046667
	#*# -0.065833, -0.093333, -0.087500, -0.087500, -0.075833, -0.095833
	#*# -0.057500, -0.081667, -0.130833, -0.113333, -0.115833, -0.108333
	#*# -0.075833, -0.088333, -0.116667, -0.102500, -0.096667, -0.102500
	#*# -0.134167, -0.137500, -0.130000, -0.110000, -0.093333, -0.054167
	#*# -0.126667, -0.116667, -0.106667, -0.061667, 0.009167, 0.051667
	#*# tension = 0.2
	#*# min_x = 50.0
	#*# algo = lagrange
	#*# y_count = 6
	#*# mesh_y_pps = 2
	#*# min_y = 10.0
	#*# x_count = 6
	#*# max_y = 270.0
	#*# mesh_x_pps = 2
	#*# max_x = 290.0
	#*#
	#*# [bltouch]
	#*# z_offset = 2.100
	#*#
	#*# [heater_bed]
	#*# control = pid
	#*# pid_kp = 75.650
	#*# pid_ki = 1.005
	#*# pid_kd = 1424.118