log

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2014.01-openwrt4-g9abc897-dirty (Jun 27 2015 - 18:14:58)
SPL: applying tuned DDR SDRAM settings
MEM: DDR Echo DLL delay:  22/23
MEM: DDR Write DQS delay: 65/67
MEM: DDR Read DQS delay:  1f/1f
SPL: loading U-Boot to RAM
SPL: checking U-Boot image
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2014.01-openwrt4-g9abc897-dirty (Jun 27 2015 - 18:14:58) BTHOMEHUBV5A

Board: BT Home Hub 5A
SoC:   Lantiq VRX268 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  2  1  0 

NAND read: device 0 offset 0xa0000, size 0x200000
 2097152 bytes read: OK
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.4.3
   Created:      2016-03-02  17:40:58 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1701047 Bytes = 1.6 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
[    0.000000] Linux version 4.4.3 (christopher@Ubuntu-xw4600) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r48886) ) #2 Thu Mar 3 18:41:40 UTC 2016
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is BTHOMEHUBV5A - BT Home Hub 5A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00040804
[    0.000000] Readback ErrCtl register=00040804
[    0.000000] Memory: 124328K/131072K available (3776K kernel code, 167K rwdata, 1144K rodata, 208K init, 211K bss, 6744K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007855] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042317] pid_max: default: 32768 minimum: 301
[    0.047152] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053724] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.066635] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.076413] pinctrl core: initialized pinctrl subsystem
[    0.082238] NET: Registered protocol family 16
[    0.091281] pinctrl-xway 1e100b10.pinmux: Init done
[    0.096768] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.206757] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.221796] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.227436]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.232692]   IO 0x000000001ae00000..0x000000001affffff
[    0.356113] ath9k,eeprom ath9k_eep: failed to load eeprom address
[    0.376036] usbcore: registered new interface driver usbfs
[    0.381518] usbcore: registered new interface driver hub
[    0.386879] usbcore: registered new device driver usb
[    0.392276] PCI host bridge to bus 0000:00
[    0.396267] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.403176] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.409169] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.416021] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.424586] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.431422] PCI host bridge to bus 0000:01
[    0.435415] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.442330] pci_bus 0000:01: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.449275] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.456130] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.464190] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.482225] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring
[    0.490971] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c1fffff]
[    0.497645] pci 0000:01:00.0: BAR 9: assigned [mem 0x1c200000-0x1c2fffff pref]
[    0.504916] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c1fffff 64bit]
[    0.512312] pci 0000:02:00.0: BAR 6: assigned [mem 0x1c200000-0x1c20ffff pref]
[    0.519577] pci 0000:01:00.0: PCI bridge to [bus 02]
[    0.524610] pci 0000:01:00.0:   bridge window [mem 0x1c000000-0x1c1fffff]
[    0.531466] pci 0000:01:00.0:   bridge window [mem 0x1c200000-0x1c2fffff pref]
[    0.538831] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 
[    0.545440] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.551782] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1 
[    0.558449] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
[    0.565756] clocksource: Switched to clocksource MIPS
[    0.572295] NET: Registered protocol family 2
[    0.577415] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.584307] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.590685] TCP: Hash tables configured (established 1024 bind 1024)
[    0.597191] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.603039] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.609606] NET: Registered protocol family 1
[    0.614375] gptu: totally 6 16-bit timers/counters
[    0.619190] gptu: misc_register on minor 63
[    0.623301] gptu: succeeded to request irq 126
[    0.627793] gptu: succeeded to request irq 127
[    0.632307] gptu: succeeded to request irq 128
[    0.636821] gptu: succeeded to request irq 129
[    0.641334] gptu: succeeded to request irq 130
[    0.645850] gptu: succeeded to request irq 131
[    0.651228] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.658548] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7960000
[    0.664873] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7960000
[    0.772371] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.804753] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.810499] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.823782] io scheduler noop registered
[    0.827615] io scheduler deadline registered (default)
[    0.833455] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.842355] console [ttyLTQ0] enabled
[    0.842355] console [ttyLTQ0] enabled
[    0.849681] bootconsole [early0] disabled
[    0.849681] bootconsole [early0] disabled
[    0.861172] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[    0.866069] nand: AMD/Spansion S34ML01G1
[    0.869988] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.877635] Scanning device for bad blocks
[    0.945396] Bad eraseblock 440 at 0x000003700000
[    1.032919] 5 ofpart partitions found on MTD device 14000000.nand-parts
[    1.038103] Creating 5 MTD partitions on "14000000.nand-parts":
[    1.044020] 0x000000000000-0x000000040000 : "u-boot"
[    1.050794] 0x000000040000-0x000000080000 : "uboot-env"
[    1.056629] 0x000000080000-0x0000000a0000 : "caldata"
[    1.062379] 0x0000000a0000-0x0000002a0000 : "kernel"
[    1.067967] 0x0000002a0000-0x000008000000 : "ubi"
[    1.176221] libphy: lantiq,xrx200-mdio: probed
[    1.250489] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    1.318462] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    1.386447] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.454446] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.526472] eth1: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.533362] wdt 1f8803f0.watchdog: Init done
[    1.539918] NET: Registered protocol family 10
[    1.549062] NET: Registered protocol family 17
[    1.552222] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.564731] 8021q: 802.1Q VLAN Support v1.8
[    1.572988] ath9k,eeprom ath9k_eep: pci slot: 14
[    1.576181] pci 0000:00:0e.0: fixup device configuration
[    1.583106] pci 0000:00:0e.0: fixup info: [168c:002d] revision 01 class 0x028000
[    1.589091] ath9k,eeprom ath9k_eep: loaded ath9k eeprom
[    1.598216] UBI: auto-attach mtd4
[    1.599903] ubi0: attaching mtd4
[    2.237534] ubi0: scanning is finished
[    2.278973] ubi0: attached mtd4 (name "ubi", size 125 MiB)
[    2.283052] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    2.289898] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    2.296598] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[    2.303388] ubi0: good PEBs: 1002, bad PEBs: 1, corrupted PEBs: 0
[    2.309479] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    2.316709] ubi0: max/mean erase counter: 175/130, WL threshold: 4096, image sequence number: 424358759
[    2.326117] ubi0: available PEBs: 0, total reserved PEBs: 1002, PEBs reserved for bad PEB handling: 19
[    2.335602] ubi0: background thread "ubi_bgt0d" started, PID 309
[    2.447567] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 311
[    2.559511] UBIFS error (ubi0:0 pid 1): ubifs_recover_master_node: failed to recover master node
[    2.566883] UBIFS error (ubi0:0 pid 1): ubifs_recover_master_node: dumping first master node
[    2.575307]  magic          0x6101831
[    2.578959]  crc            0xde862342
[    2.582702]  node_type      7 (master node)
[    2.586881]  group_type     0 (no node group)
[    2.591232]  sqnum          8674
[    2.594451]  len            512
[    2.597562]  highest_inum   1250
[    2.600805]  commit number  34
[    2.603851]  flags          0x2
[    2.606984]  log_lnum       7
[    2.609944]  root_lnum      55
[    2.612968]  root_offs      78328
[    2.616297]  root_len       88
[    2.619345]  gc_lnum        977
[    2.622478]  ihead_lnum     55
[    2.625502]  ihead_offs     79872
[    2.628832]  index_size     163696
[    2.632225]  lpt_lnum       8
[    2.635187]  lpt_offs       69737
[    2.638492]  nhead_lnum     8
[    2.641430]  nhead_offs     71680
[    2.644759]  ltab_lnum      8
[    2.647720]  ltab_offs      69632
[    2.651026]  lsave_lnum     0
[    2.653986]  lsave_offs     0
[    2.656923]  lscan_lnum     63
[    2.659993]  leb_cnt        979
[    2.663126]  empty_lebs     909
[    2.666258]  idx_lebs       2
[    2.669197]  total_free     117561344
[    2.672875]  total_dirty    313576
[    2.676268]  total_used     6856616
[    2.679750]  total_dead     37792
[    2.683057]  total_dark     5650960
[    2.686657] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" stops
[    2.693301] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    2.700243] Please append a correct "root=" boot option; here are the available partitions:
[    2.708577] 1f00             256 mtdblock0  (driver?)
[    2.713598] 1f01             256 mtdblock1  (driver?)
[    2.718663] 1f02             128 mtdblock2  (driver?)
[    2.723694] 1f03            2048 mtdblock3  (driver?)
[    2.728742] 1f04          128384 mtdblock4  (driver?)
[    2.733805] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    2.744024] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[   33.449793] random: nonblocking pool is initialized