|
[profile] |
|
layer_height = 0.16 |
|
wall_thickness = 1.2 |
|
retraction_enable = True |
|
solid_layer_thickness = 1.2 |
|
fill_density = 10 |
|
nozzle_size = 0.4 |
|
print_speed = 50 |
|
print_temperature = 200 |
|
print_temperature2 = 0 |
|
print_temperature3 = 0 |
|
print_temperature4 = 0 |
|
print_temperature5 = 0 |
|
print_bed_temperature = 40 |
|
support = None |
|
platform_adhesion = Raft |
|
support_dual_extrusion = Both |
|
wipe_tower = False |
|
wipe_tower_volume = 15 |
|
ooze_shield = False |
|
filament_diameter = 1.75 |
|
filament_diameter2 = 0 |
|
filament_diameter3 = 0 |
|
filament_diameter4 = 0 |
|
filament_diameter5 = 0 |
|
filament_flow = 100.0 |
|
retraction_speed = 60 |
|
retraction_amount = 0.5 |
|
retraction_dual_amount = 16.5 |
|
retraction_min_travel = 1.5 |
|
retraction_combing = True |
|
retraction_minimal_extrusion = 0.02 |
|
retraction_hop = 0.0 |
|
bottom_thickness = 0.2 |
|
layer0_width_factor = 100 |
|
object_sink = 0.0 |
|
overlap_dual = 0.15 |
|
travel_speed = 60 |
|
bottom_layer_speed = 25 |
|
infill_speed = 0.0 |
|
solidarea_speed = 0.0 |
|
inset0_speed = 45 |
|
insetx_speed = 45 |
|
cool_min_layer_time = 5 |
|
fan_enabled = True |
|
skirt_line_count = 1 |
|
skirt_gap = 3.0 |
|
skirt_minimal_length = 150.0 |
|
fan_full_height = 0.5 |
|
fan_speed = 100 |
|
fan_speed_max = 100 |
|
cool_min_feedrate = 10 |
|
cool_head_lift = False |
|
solid_top = True |
|
solid_bottom = True |
|
fill_overlap = 15 |
|
perimeter_before_infill = False |
|
support_type = Grid |
|
support_angle = 60 |
|
support_fill_rate = 15 |
|
support_xy_distance = 0.7 |
|
support_z_distance = 0.15 |
|
spiralize = False |
|
simple_mode = False |
|
brim_line_count = 20 |
|
raft_margin = 5.0 |
|
raft_line_spacing = 3.0 |
|
raft_base_thickness = 0.3 |
|
raft_base_linewidth = 1.0 |
|
raft_interface_thickness = 0.27 |
|
raft_interface_linewidth = 0.4 |
|
raft_airgap_all = 0.0 |
|
raft_airgap = 0.22 |
|
raft_surface_layers = 2 |
|
raft_surface_thickness = 0.27 |
|
raft_surface_linewidth = 0.4 |
|
fix_horrible_union_all_type_a = True |
|
fix_horrible_union_all_type_b = False |
|
fix_horrible_use_open_bits = False |
|
fix_horrible_extensive_stitching = False |
|
plugin_config = |
|
object_center_x = -1 |
|
object_center_y = -1 |
|
|
|
[alterations] |
|
start.gcode = ;Sliced at: {day} {date} {time} |
|
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
|
;Print time: {print_time} |
|
;Filament used: {filament_amount}m {filament_weight}g |
|
;Filament cost: {filament_cost} |
|
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
|
;M109 S{print_temperature} ;Uncomment to add your own temperature line |
|
G21 ;metric values |
|
G90 ;absolute positioning |
|
M82 ;set extruder to absolute mode |
|
M107 ;start with the fan off |
|
G28 X0 Y0 ;move X/Y to min endstops |
|
G28 Z0 ;move Z to min endstops |
|
G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E3 ;extrude 3mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F{travel_speed} |
|
;Put printing message on LCD screen |
|
M117 Printing... |
|
end.gcode = ;End GCode |
|
M104 S0 ;extruder heater off |
|
M140 S0 ;heated bed heater off (if you have it) |
|
G91 ;relative positioning |
|
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
|
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
|
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
|
M84 ;steppers off |
|
G90 ;absolute positioning |
|
;{profile_string} |
|
start2.gcode = ;Sliced at: {day} {date} {time} |
|
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
|
;Print time: {print_time} |
|
;Filament used: {filament_amount}m {filament_weight}g |
|
;Filament cost: {filament_cost} |
|
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
|
;M104 S{print_temperature} ;Uncomment to add your own temperature line |
|
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line |
|
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line |
|
G21 ;metric values |
|
G90 ;absolute positioning |
|
M107 ;start with the fan off |
|
G28 X0 Y0 ;move X/Y to min endstops |
|
G28 Z0 ;move Z to min endstops |
|
G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
|
T1 ;Switch to the 2nd extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F200 E-{retraction_dual_amount} |
|
T0 ;Switch to the first extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F{travel_speed} |
|
;Put printing message on LCD screen |
|
M117 Printing... |
|
end2.gcode = ;End GCode |
|
M104 T0 S0 ;extruder heater off |
|
M104 T1 S0 ;extruder heater off |
|
M140 S0 ;heated bed heater off (if you have it) |
|
G91 ;relative positioning |
|
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
|
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
|
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
|
M84 ;steppers off |
|
G90 ;absolute positioning |
|
;{profile_string} |
|
start3.gcode = ;Sliced at: {day} {date} {time} |
|
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
|
;Print time: {print_time} |
|
;Filament used: {filament_amount}m {filament_weight}g |
|
;Filament cost: {filament_cost} |
|
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
|
;M104 S{print_temperature} ;Uncomment to add your own temperature line |
|
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line |
|
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line |
|
G21 ;metric values |
|
G90 ;absolute positioning |
|
M107 ;start with the fan off |
|
G28 X0 Y0 ;move X/Y to min endstops |
|
G28 Z0 ;move Z to min endstops |
|
G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
|
T2 ;Switch to the 2nd extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F200 E-{retraction_dual_amount} |
|
T1 ;Switch to the 2nd extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F200 E-{retraction_dual_amount} |
|
T0 ;Switch to the first extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F{travel_speed} |
|
;Put printing message on LCD screen |
|
M117 Printing... |
|
end3.gcode = ;End GCode |
|
M104 T0 S0 ;extruder heater off |
|
M104 T1 S0 ;extruder heater off |
|
M104 T2 S0 ;extruder heater off |
|
M140 S0 ;heated bed heater off (if you have it) |
|
G91 ;relative positioning |
|
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
|
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
|
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
|
M84 ;steppers off |
|
G90 ;absolute positioning |
|
;{profile_string} |
|
start4.gcode = ;Sliced at: {day} {date} {time} |
|
;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} |
|
;Print time: {print_time} |
|
;Filament used: {filament_amount}m {filament_weight}g |
|
;Filament cost: {filament_cost} |
|
;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line |
|
;M104 S{print_temperature} ;Uncomment to add your own temperature line |
|
;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line |
|
;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line |
|
;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line |
|
G21 ;metric values |
|
G90 ;absolute positioning |
|
M107 ;start with the fan off |
|
G28 X0 Y0 ;move X/Y to min endstops |
|
G28 Z0 ;move Z to min endstops |
|
G1 Z15.0 F{travel_speed} ;move the platform down 15mm |
|
T3 ;Switch to the 4th extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F200 E-{retraction_dual_amount} |
|
T2 ;Switch to the 3th extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F200 E-{retraction_dual_amount} |
|
T1 ;Switch to the 2nd extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F200 E-{retraction_dual_amount} |
|
T0 ;Switch to the first extruder |
|
G92 E0 ;zero the extruded length |
|
G1 F200 E10 ;extrude 10mm of feed stock |
|
G92 E0 ;zero the extruded length again |
|
G1 F{travel_speed} |
|
;Put printing message on LCD screen |
|
M117 Printing... |
|
end4.gcode = ;End GCode |
|
M104 T0 S0 ;extruder heater off |
|
M104 T1 S0 ;extruder heater off |
|
M104 T2 S0 ;extruder heater off |
|
M104 T3 S0 ;extruder heater off |
|
M140 S0 ;heated bed heater off (if you have it) |
|
G91 ;relative positioning |
|
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure |
|
G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more |
|
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way |
|
M84 ;steppers off |
|
G90 ;absolute positioning |
|
;{profile_string} |
|
support_start.gcode = |
|
support_end.gcode = |
|
cool_start.gcode = |
|
cool_end.gcode = |
|
replace.csv = |
|
preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. |
|
;This code is added before the T(n) |
|
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. |
|
;This code is added after the T(n) |
The Cura version that comes with the printer has GCode flavor set to RepRap, Without looking, I selected RepRap in the new Cura, but realized how it was named in the old version. How is Marlin working for you? I think I should be picking that one for my MP Plus.
Cura for MP:
Availble settings for Cura 3.3.1: