comtrend-ar5315u-oem-firmware, alternative boot configured at CFE Boot image (0=latest, 1=previous) => 1

comtrend-ar5315u-oem-firmware.txt

Resetting board in 0 seconds...HELO
CPUI
L1CI
DRAM
----
PHYS
PHYE
DDR1
333H
SIZ3
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.38-112.118-15 for BCM96318 (32bit,SP,BE)
Build Date: 四  4月 11 21:08:50 CST 2013 (joba@SW1-BCM-02)
Copyright (C) 2000-2011 Broadcom Corporation.

HS Serial flash device: name ID_W25X128, id 0xef18 size 16384KB
Total Flash size: 16384K with 4096 sectors
Flash not used for Auxillary File System
Chip ID: BCM6318B0, MIPS: 333MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

##checkForResetToDefaultHold:791##
Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Boot image (0=latest, 1=previous) : 1  
Board Id (0-5)                    : 96318A-1441N1  
Number of MAC Addresses (1-32)    : 32  
Base MAC Address                  : d8:b6:b7:11:7d:1d  
PSI Size (1-64) KBytes            : 24  
Enable Backup PSI [0|1]           : 1  
System Log Size (0-256) KBytes    : 256  
Auxillary File System Size Percent: 0  
Main Thread Number [0|1]          : 0  
WLAN Password                     : jUWNGQGDLPrTvMfGxSm3  
Serial Number                     : 1615315UXXF-BA011593  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from previous image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x802e0a60
Decompression OK!
Entry at 0x802e0a60
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x802e0a60
Linux version 2.6.30 (daiyang@SWD120) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed Nov 12 16:09:38 CST 2014
HS Serial flash device: name ID_W25X128, id 0xef18 size 16384KB
96318A-1441N1 prom init
CPU revision is: 00029033 (Broadcom BCM3302)
DSL SDRAM reserved: 0x100000
Determined physical RAM map:
 memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8039b610, node_mem_map 81000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 59876k/64512k available (2907k kernel code, 4616k reserved, 726k data, 132k init, 0k highmem)
Calibrating delay loop... 331.77 BogoMIPS (lpj=165888)
Mount-cache hash table entries: 512
--Kernel Config--
  SMP=0
  PREEMPT=0
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
Broadcom Logger v0.1 Nov 12 2014 16:07:18
net_namespace: 1128 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 4096 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio: [0x10005100-0x100051ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10005000-0x100050ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x007fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0xa0000000-0xa00fffff
pci 0000:01:00.0:   PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Nov 12 2014 16:09:33 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 116
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6318] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v2.0
File system address: 0xb8010100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8010100,6873088]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10005000
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10005100
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
sesBtn_mapIntr: is_sesBtn_irq_shared=0, sesBtn_irq=3
SES: LED GPIO 0x0 is enabled
brcm_board_init: isShared=0, rstToDflt_irq=0
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized

bcmxtmrt: Broadcom BCM6318B0 ATM/PTM Network Device v0.4 Nov 12 2014 16:09:21
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    input device check on 
    Actions configured 
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 132k freed

init started: BusyBox v1.17.2 (2014-11-12 16:11:49 CST)
starting pid 190, tty '': '/etc/init.d/rcS'
starting pid 193, tty '': '-/bin/sh'


BusyBox v1.17.2 (2014-11-12 16:11:49 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules... 

chipinfo: module license 'proprietary' taints kernel.
Disabling lock debugging due to kernel taint
brcmchipinfo: brcm_chipinfo_init entry
NBUFF v1.0 Initialized
Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v2.2 Nov 12 2014 16:07:31 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Nov 12 2014 16:07:31
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6318B0 Ethernet Network Device v0.1 Nov 12 2014 16:09:15
ETH Init: Ch:0 - 200 tx BDs at 0xa398c000
ETH Init: Ch:1 - 200 tx BDs at 0xa3afe000
ETH Init: Ch:0 - 400 rx BDs at 0xa3afd000
ETH Init: Ch:1 - 100 rx BDs at 0xa39f3800
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered 
eth0: MAC Address: D8:B6:B7:11:7D:1D
eth1: MAC Address: D8:B6:B7:11:7D:1D
eth2: MAC Address: D8:B6:B7:11:7D:1D
eth3: MAC Address: D8:B6:B7:11:7D:1D
BCM63XX_USB USB Device not present
insmod: can't insert '/lib/modules/2.6.30/extra/bcm_usb.ko': No such device
wl: dsl_tx_pkt_flush_len=338
wl: high_wmark_tot=400
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl: passivemode=1
wl: napimode=0
wl0: allocskbmode=1 currallocskbsz=256
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43217_map.bin
srom rev:8
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16
wl0: Broadcom BCMa8db 802.11 Wireless Controller 6.30.102.7.cpe4.12L07.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 
Broadcom 802.1Q VLAN Interface, v0.1

===== Release Version 4.12L.07 (build timestamp 141112_1610) =====

backup Config 1 ==> config 2.
backup_psi_number_blk=6 result=24576
wait instruction: enabled
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
device eth0 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth1 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth2 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth2: link is not ready
device eth3 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth3: link is not ready
device wl0 entered promiscuous mode
WLmngr Daemon is running
optarg=0 shmId=0 
wlevt is ready for new msg...
br0: port 5(wl0) entering forwarding state
BcmAdsl_Initialize=0xC00D60C0, g_pFnNotifyCallback=0xC010AF64
pSdramPHY=0xA3FFFFF8, 0x19E4D 0xDEADBEEF
*** XfaceOffset: 0x1C790 => 0x1C790 ***
*** PhySdramSize got adjusted: 0x8F9D8 => 0xA561C ***
AdslCoreSharedMemInit: shareMemSize=371133(371136)
AdslCoreHwReset:  pLocSbSta=831c0000 bkupThreshold=1600
AdslCoreHwReset:  AdslOemDataAddr = 0xA3F84590
***BcmDiagsMgrRegisterClient: 0 ***dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 
XTM Init: Ch:0 - 400 rx BDs at 0xa2467000
XTM Init: Ch:1 - 16 rx BDs at 0xa3178e80
bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system 
bcmxtmcfg: gulBondDslMonitorValid = 1 
monitor task is initialized pid= 290 
There is no Predefined DevicePin in CFE
WPS Device PIN = 12279180
br0: port 5(wl0) entering disabled state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
killall: hspotap: no process killed
br0: port 5(wl0) entering disabled state
Setting SSID: "BrcmAP0"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x1001
wlctl: Unsupported
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state

BCM96318 Broadband Router
Login: 
Password: