Printers Config

macros.cfg

[gcode_macro G29]
gcode:
    G28
    BED_MESH_CALIBRATE
    G0 X0 Y0 Z10 F6000
    BED_MESH_PROFILE save=default


[gcode_macro WIPE_NOZZLE]
gcode:
    G1 X250 ; Wipe the nozzle
    G1 X240 ; Wipe the nozzle
    G1 X250 ; Wipe the nozzle
    G1 X240 ; Wipe the nozzle
    G1 X250 ; Wipe the nozzle
    G1 X240 ; Wipe the nozzle


[gcode_macro START_PRINT]
gcode:
    {% set BED = params.BED|int %}
    {% set EXTRUDER = params.EXTRUDER|int %}

    M117 Setting Inital Temps

    M140 S{BED}
    # M104 S215.0{BED}
    # M104 S215.0{EXTRUDER}
    # M140 S{extruder_temp_standby}

    G90                                     # Use absolute coordinates
    # SET_GCODE_OFFSET Z=0.0                # Reset the G-Code Z offset (adjust Z offset if needed)

    G28                                     # Home the printer
    BED_MESH_PROFILE LOAD="default"
    G92 E0                                  # Reset Extruder
    G1 Z2.0 F3000                           # Move Z Axis up

    M106 S50                                ; Fan on approx. 20% to protect cooling ducts

    # M190 S{BED}                           ; Wait for bed to reach temperature
    M109 S{EXTRUDER}                        ; Wait for extruder to reach temperature


    # M117 Wiping the nozzle
    WIPE_NOZZLE

    M117 Purge line

    G1 X2.1 Y20 Z0.28 F5000.0         # Move to start position

    G1 X2.1 Y200.0 Z0.28 F1500.0 E15  # Draw the first line
    G1 X2.4 Y200.0 Z0.28 F5000.0      # Move to side a little
    G1 X2.4 Y20 Z0.28 F1500.0 E30     # Draw the second line

    G92 E0                            # Reset Extruder
    G1 Z2.0 F3000                     # Move Z Axis up

    WIPE_NOZZLE
    M117 Lets Print!

[gcode_macro END_PRINT]
gcode:
    # Turn off bed, extruder, and fan
    M140 S0
    M104 S0
    M106 S0
    # Move nozzle away from print while retracting
    G91
    # Raise nozzle

    {% if printer.toolhead.position.z < 50 %}
    G1 Z50 E-3 F3000
    {% elif printer.toolhead.position.z < 265 %}
    G1 Z3 E-3 F3000
    {% else %}
    G1 E-3 F3000
    {% endif %}

    G1 X2 Y2 F3000

    # Set Absolute positioning
    G90
    G1 X200 Y227
    G91
    #G1 Z-3 F3000 # weg als dit werkt
    G90

    #Disable steppers
    M84

[gcode_macro PAUSE]
description: Pause the actual running print
rename_existing: PAUSE_BASE
# change this if you need more or less extrusion
variable_extrude: 1.0
gcode:
  ##### read E from pause macro #####
  {% set E = printer["gcode_macro PAUSE"].extrude|float %}
  ##### set park positon for x and y #####
  # default is your max posion from your printer.cfg
  {% set x_park = printer.toolhead.axis_maximum.x|float - 15.0 %}
  {% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
  ##### calculate save lift position #####
  {% set max_z = printer.toolhead.axis_maximum.z|float %}
  {% set act_z = printer.toolhead.position.z|float %}
  {% if act_z < (max_z - 2.0) %}
      {% set z_safe = 2.0 %}
  {% else %}
      {% set z_safe = max_z - act_z %}
  {% endif %}
  ##### end of definitions #####
  WIPE_NOZZLE
  PAUSE_BASE
  G91
  {% if printer.extruder.can_extrude|lower == 'true' %}
    G1 E-{E} F2100
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}
  {% if "xyz" in printer.toolhead.homed_axes %}
    G1 Z{z_safe} F900
    G90
    G1 X{x_park} Y{y_park} F6000
  {% else %}
    {action_respond_info("Printer not homed")}
  {% endif %}

[gcode_macro RESUME]
description: Resume the actual running print
rename_existing: RESUME_BASE
gcode:
  ##### read E from pause macro #####
  {% set E = printer["gcode_macro PAUSE"].extrude|float %}
  #### get VELOCITY parameter if specified ####
  {% if 'VELOCITY' in params|upper %}
    {% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
  {%else %}
    {% set get_params = "" %}
  {% endif %}
  ##### end of definitions #####
  {% if printer.extruder.can_extrude|lower == 'true' %}
    WIPE_NOZZLE
    G91
    G1 E{E} F2100
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}
  RESUME_BASE {get_params}


[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
  PAUSE
  TURN_OFF_HEATERS
  CANCEL_PRINT_BASE
  CLEAR_PAUSE



[gcode_macro M600]
description: Starts process of Filament Change
gcode:
  {% if printer.extruder.temperature < 180 %}
    {action_respond_info("Extruder temperature too low")}
  {% else %}
    AFC_PAUSE
    _DISABLE_FS
    UNLOAD_FILAMENT
  {% endif %}

[gcode_macro AFC_PAUSE]
description: Pauses Print
gcode:
    PAUSE
    SET_IDLE_TIMEOUT TIMEOUT={ 30 * 60 }

[gcode_macro AFC_RESUME]
description: Resume print after Filament Change
gcode:
    ##### read E from pause macro #####
    {% set E = printer["gcode_macro PAUSE"].extrude|float %}
    SET_IDLE_TIMEOUT TIMEOUT={ 10 * 60 }
    G1 E-{ E }
    # Reset extruder position
    G92 E0
    LOAD_FILAMENT
    RESUME


[gcode_macro UNLOAD_FILAMENT]
description: Unloads Filament from extruder
gcode:
  {% if printer.extruder.temperature < 180 %}
    {action_respond_info("Extruder temperature too low")}
  {% else %}
    SAVE_GCODE_STATE NAME=UNLOAD_state
    {% set z_lift = params.z_lift|default(50)|int %}
    {% set axis_max = printer.toolhead.axis_maximum %}
    {% set pos = printer.toolhead.position %}

    {% set z_diff = axis_max.z - pos.z %}
    {% set z_safe_lift = [ z_lift, z_diff ] | min%}

    G91                   # relative positioning
    G0 Z{ z_safe_lift }
    # Reset extruder position
    G92 E0
    G1 E5.0 F300        # extrude a little
    G1 E-50 F{ 10 * 60 } # perform the unload
    G1 E-50 F{ 5 * 60 }   # finish the unload
    RESTORE_GCODE_STATE NAME=UNLOAD_state
  {% endif %}

[gcode_macro LOAD_FILAMENT]
description: Loads filament into the extruder
gcode:
  {% if printer.extruder.temperature < 180 %}
    {action_respond_info("Extruder temperature too low")}
  {% else %}
    SAVE_GCODE_STATE NAME=LOAD_state
    G91                   # Relative coords
    G1 E50 F{ 5 * 60 }  # extrude
    G4 P{ 0.9 * 1000 }    # dwell (ms)
    G1 E25.0 F{ 5 * 60 }  # extrude a little more
    _ENABLE_FS
    RESTORE_GCODE_STATE NAME=LOAD_state
  {% endif %}

[gcode_macro _DISABLE_FS]
description: placeholder, disables filament sensor that might trigger an M600 in the middle of a load/unload/M600...
gcode:
    SET_FILAMENT_SENSOR SENSOR=RunoutSensor ENABLE=0

[gcode_macro _ENABLE_FS]
description: placeholder, enables filament sensor
gcode:
    SET_FILAMENT_SENSOR SENSOR=RunoutSensor ENABLE=1


[gcode_macro PURGE]
description: Extrudes filament, used to clean out previous filament
gcode:
  {% if printer.extruder.temperature < 180 %}
    {action_respond_info("Extruder temperature too low")}
  {% else %}
    SAVE_GCODE_STATE NAME=PURGE_state
    G91                   # relative coords
    G1 E45.0 F{ 5 * 60 }  # purge
    RESTORE_GCODE_STATE NAME=PURGE_state
  {% endif %}


# [gcode_macro HEAT]
# description: Heats up the extruder to get ready for Filament Change
# gcode:
#   SET_HEATER_TEMPERATURE HEATER=extruder TARGET=200
#   HOME_CHECK
#   G1 Z10 F3000

# [gcode_macro COOL]
# description: Turns off all heaters
# gcode:
#   TURN_OFF_HEATERS

# [gcode_macro BED_TRAMMING_1]
# description: Heats bed and starts process to level the bed with the screws
# gcode:
#   M140 S60
#   HOME_CHECK
#   M190 S60
#   SCREWS_TILT_CALCULATE

# [gcode_macro BED_TRAMMING_2]
# description: Continues the bed screw leveling process
# gcode:
#   SCREWS_TILT_CALCULATE

[gcode_macro BED_MESH]
description: Heats bed, makes a mesh and saves it
gcode:
  M140 S60
  HOME_CHECK
  M190 S60
  BED_MESH_CLEAR
  BED_MESH_CALIBRATE
  TURN_OFF_HEATERS
  SAVE_CONFIG

[gcode_macro DISABLE_STEPPERS]
description: Disables the printers stepper motors
gcode:
  M84 X Y E

[gcode_macro PID_EXTRUDER]
description: PID Tune for the Extruder
gcode:
  PID_CALIBRATE HEATER=extruder TARGET=200
  TURN_OFF_HEATERS
  SAVE_CONFIG

[gcode_macro PID_BED]
description: PID Tune for the Bed
gcode:
  PID_CALIBRATE HEATER=heater_bed TARGET=60
  TURN_OFF_HEATERS
  SAVE_CONFIG

[gcode_macro NOZZLE_MID]
description: Moves nozzle to the center of the bed
gcode:
  HOME_CHECK
  G1 X110 Y110 Z10 F6000

[gcode_macro home_check]
description: Checks if the printer is homed, it not it homes the printer
gcode:
  {% if printer.toolhead.homed_axes != "xyz" %}
  G28
  {% endif %}

[gcode_macro SHOW_PRINT]
description: Moves the extruder out of the way and bed forward
gcode:
    HOME_CHECK
    {% set z_lift = params.z_lift|default(50)|int %}
    {% set axis_max = printer.toolhead.axis_maximum %}
    {% set pos = printer.toolhead.position %}

    {% set z_diff = axis_max.z - pos.z %}
    {% set z_safe_lift = [ z_lift, z_diff ] | min%}
    G1 Z{ z_safe_lift }
    G1 X10 Y220 F4000

[gcode_macro ZOffset_Setup]
description: Starts Z-Offset Calibration, under 30 degrees Celsius
gcode:
  {% if printer.heater_bed.temperature > 35 %}
    {action_respond_info("Bed temperature too high")}
  {% elif printer.extruder.temperature > 35 %}
    {action_respond_info("Extruder temperature too High")}
  {% else %}
  G28
  PROBE_CALIBRATE
  {% endif %}

# [gcode_macro Z_Down_01]
# description: Moves Z down by 0.1
# gcode:
#   TESTZ Z=-.1

# [gcode_macro Z_Up_01]
# description: Moves Z up by 0.1
# gcode:
#   TESTZ Z=+.1

# [gcode_macro Z_Low_Half]
# description: Sets Z between current value and previous lower value
# gcode:
#   TESTZ Z=-

# [gcode_macro Z_High_Half]
# description: Sets Z between current value and previous higher value
# gcode:
#   TESTZ Z=+

[gcode_macro Accept_Save]
description: Accepts the Z-Offset and saves the config
gcode:
  ACCEPT
  SAVE_CONFIG

[gcode_macro Abort_Setup]
description: Aborts the Z-Offset calibration
gcode:
  ABORT

[screws_tilt_adjust]
horizontal_move_z: 5
screw1: 50,220
screw1_name: Back left
screw2: 228,220
screw2_name: Back Right
screw3: 50,74
screw3_name: Front Left
screw4: 228,74
screw4_name: Front Right

printer.cfg (S1 Pro)

##################Creality Ender 3 S1 Pro Klipper Config - 3DPrintBeginner###############
######Full guide: https://3dprintbeginner.com/how-to-install-klipper-on-ender-3-s1/######

[include macros.cfg]

[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: -5
position_min: -5
position_max: 252
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: -5
position_min: -5
position_max: 232
homing_speed: 50

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 270
position_min: -5

[extruder]
max_extrude_only_distance: 100.0
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 7.6190
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 21.761
pid_Ki: 1.261
pid_Kd: 93.844
min_temp: 0
max_temp: 250
pressure_advance = 0.07
max_extrude_cross_section: 50.0

[filament_switch_sensor RunoutSensor]
pause_on_runout: False
runout_gcode: PAUSE
insert_gcode: RESUME
switch_pin: !PC15

[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 68.385
pid_Ki: 1.093
pid_Kd: 1069.370
min_temp: 0
max_temp: 130


[heater_fan hotend_fan]
pin: PC0
heater: extruder
heater_temp: 50.0

[fan]
pin: PA0

[mcu]
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3.1:1.0-port0
restart_method: command

[mcu rpi]
serial: /tmp/klipper_host_mcu

[adxl345]
cs_pin: rpi:None

[resonance_tester]
accel_chip: adxl345
probe_points:
    100, 100, 20  # an example

[input_shaper]
shaper_freq_x: 58.0
shaper_type_x: ei
shaper_freq_y: 49.6
shaper_type_y: ei

[printer]
kinematics: cartesian
max_velocity: 500
max_accel: 4600
max_accel_to_decel: 3000
max_z_velocity: 5
square_corner_velocity: 5.0
max_z_accel: 100

[bltouch]
sensor_pin: ^PC14
control_pin: PC13
x_offset: -32
y_offset: -41
#z_offset: 2.900
speed:10
samples:1
samples_result:average
probe_with_touch_mode: true
stow_on_each_sample: false

[safe_z_home]
home_xy_position: 147,154
speed: 100
z_hop: 10
z_hop_speed: 5

[bed_mesh]
speed: 100
mesh_min: 7, 7
mesh_max: 220, 185
algorithm: bicubic
probe_count: 3,3
fade_start: 1
fade_end: 3
fade_target: 0
mesh_pps: 2,2
algorithm: bicubic
bicubic_tension: 0.2

# [temperature_sensor Raspberry_Pi]
# sensor_type: temperature_host
# min_temp: 0
# max_temp: 100

[virtual_sdcard]
path: ~/Tom_data/gcodes

[display_status]

[pause_resume]

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bltouch]
#*# z_offset = 0.375
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*#       0.240000, 0.227500, 0.255000
#*#       0.070000, -0.017500, -0.045000
#*#       0.265000, 0.215000, 0.237500
#*# x_count = 3
#*# y_count = 3
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 7.0
#*# max_x = 220.0
#*# min_y = 7.0
#*# max_y = 185.0

prtiner.cfg (S1)

##################Creality Ender 3 S1 Klipper Config - 3DPrintBeginner###############
######Full guide: https://3dprintbeginner.com/how-to-install-klipper-on-ender-3-s1/######

[include macros.cfg]

[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: -5
position_min: -5
position_max: 252
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: -5
position_min: -5
position_max: 232
homing_speed: 50

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 270
position_min: -5

[extruder]
max_extrude_only_distance: 100.0
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 7.6190
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 21.761
pid_Ki: 1.261
pid_Kd: 93.844
min_temp: 0
max_temp: 250
pressure_advance = 0.07
max_extrude_cross_section: 50.0

[filament_switch_sensor RunoutSensor]
pause_on_runout: False
runout_gcode: PAUSE
insert_gcode: RESUME
switch_pin: !PC15

[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 68.385
pid_Ki: 1.093
pid_Kd: 1069.370
min_temp: 0
max_temp: 130


[heater_fan hotend_fan]
pin: PC0
heater: extruder
heater_temp: 50.0

[fan]
pin: PA0

[mcu]
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3.4:1.0-port0
restart_method: command

[mcu rpi]
serial: /tmp/klipper_host_mcu

[adxl345]
cs_pin: rpi:None


[input_shaper]
shaper_freq_x: 45.0
shaper_type_x: ei
shaper_freq_y: 54.6
shaper_type_y: ei


[resonance_tester]
accel_chip: adxl345
probe_points:
    100, 100, 20  # an example

[printer]
kinematics: cartesian
max_velocity: 500
max_accel: 3600
max_accel_to_decel: 3000
max_z_velocity: 5
square_corner_velocity: 5.0
max_z_accel: 100

[bltouch]
sensor_pin: ^PC14
control_pin: PC13
x_offset: -32
y_offset: -41
#z_offset: 2.900
speed:10
samples:1
samples_result:average
probe_with_touch_mode: true
stow_on_each_sample: false

[safe_z_home]
home_xy_position: 147,154
speed: 100
z_hop: 10
z_hop_speed: 5

[bed_mesh]
speed: 100
mesh_min: 7, 7
mesh_max: 220, 185
algorithm: bicubic
probe_count: 3,3
fade_start: 1
fade_end: 3
fade_target: 0
mesh_pps: 2,2
algorithm: bicubic
bicubic_tension: 0.2

[virtual_sdcard]
path: ~/Bert_data/gcodes

[display_status]

[pause_resume]

[temperature_sensor raspberry_pi]
sensor_type: temperature_host
min_temp: 0
max_temp: 70

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bltouch]
#*# z_offset = 1.530
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*#     0.025000, -0.095000, 0.097500
#*#     0.017500, -0.070000, 0.147500
#*#     0.210000, 0.117500, 0.325000
#*# x_count = 3
#*# y_count = 3
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 7.0
#*# max_x = 220.0
#*# min_y = 7.0
#*# max_y = 185.0