Skip to content

Instantly share code, notes, and snippets.

@kylemd
Last active March 9, 2022 22:06
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save kylemd/631b1ee60226d7c7bb950d04e107471a to your computer and use it in GitHub Desktop.
Save kylemd/631b1ee60226d7c7bb950d04e107471a to your computer and use it in GitHub Desktop.
Arcadyan AW1000 Full Bootlog
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.03.10 09:01:39 =~=~=~=~=~=~=~=~=~=~=~=
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158
S - IMAGE_VARIANT_STRING=HAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e5
B - 201 - PBL, Start
B - 2735 - bootable_media_detect_entry, Start
B - 3448 - bootable_media_detect_success, Start
B - 3452 - elf_loader_entry, Start
B - 7634 - auth_hash_seg_entry, Start
B - 7880 - auth_hash_seg_exit, Start
B - 69811 - elf_segs_hash_verify_entry, Start
B - 132654 - PBL, End
B - 147284 - SBL1, Start
B - 200415 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 207034 - pm_device_init, Start
B - 332084 - PM_SET_VAL:Skip
D - 124531 - pm_device_init, Delta
B - 334524 - pm_driver_init, Start
D - 5398 - pm_driver_init, Delta
B - 340837 - clock_init, Start
D - 2135 - clock_init, Delta
B - 344863 - boot_flash_init, Start
D - 16531 - boot_flash_init, Delta
B - 365085 - boot_config_data_table_init, Start
D - 3995 - boot_config_data_table_init, Delta - (575 Bytes)
B - 372466 - Boot Setting : 0x00000618
B - 376553 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B - 383385 - sbl1_ddr_set_params, Start
B - 387197 - CPR configuration: 0x30c
B - 390644 - cpr_init, Start
B - 393419 - Rail:0 Mode: 5 Voltage: 840000
B - 398635 - CL CPR settled at 792000mV
B - 401471 - Rail:1 Mode: 5 Voltage: 896000
B - 405650 - Rail:1 Mode: 7 Voltage: 944000
D - 16531 - cpr_init, Delta
B - 412543 - Pre_DDR_clock_init, Start
B - 416569 - Pre_DDR_clock_init, End
B - 419863 - DDR Type : PCDDR3
B - 425597 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 430355 - DDR: Start of HAL DDR Boot Training
B - 435113 - DDR: End of HAL DDR Boot Training
B - 440786 - DDR: Checksum to be stored on flash is 347078735
B - 451095 - Image Load, Start
D - 215909 - QSEE Image Loaded, Delta - (1376448 Bytes)
B - 667065 - Image Load, Start
D - 61 - SEC Image Loaded, Delta - (0 Bytes)
B - 674751 - Image Load, Start
D - 12017 - DEVCFG Image Loaded, Delta - (26008 Bytes)
B - 686860 - Image Load, Start
D - 23027 - RPM Image Loaded, Delta - (86584 Bytes)
B - 709948 - Image Load, Start
D - 88664 - APPSBL Image Loaded, Delta - (563504 Bytes)
B - 798764 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 804559 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 810964 - SBL1, End
D - 665968 - SBL1, Delta
S - Flash Throughput, 6907 KB/s (2053791 Bytes, 297336 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Mar 19 2021 - 12:06:59 +0800)
DRAM: smem ram ptable found: ver: 1 len: 4
1 GiB
NAND: Could not find nand_gpio in dts, using defaults
Not an ONFI device
ONFI probe failed
ID = 2691a398
Vendor = 98
Device = a3
qpic_nand: changing oobsize to 160 from 256 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
1024 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI0 is not defined in the device tree
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010008
MMC Device 0 not found
[arc_board_setting]
[serial_register_init]
Hit any key to stop autoboot: 2  1  0
[do_boot_unsignedimg(887)] debug:0
[do_boot_unsignedimg(918)] runcmd:setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x6400000@0x1000000(fs),${msmparts} && ubi part fs && ubi read 0x44000000 kernel &&
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=0", size 100 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 13/3, WL threshold: 4096, image sequence number: 2131456819
ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume kernel to 44000000
No size specified -> Using max size (6094848)
[do_boot_unsignedimg(988)] mtdids:nand0=nand0
## Loading kernel from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.4.60
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x440000e4
Data Size: 3975810 Bytes = 3.8 MiB
Architecture: ARM
OS: Linux
Load Address: 0x41208000
Entry Point: 0x41208000
Hash algo: crc32
Hash value: 0af6f29c
Hash algo: sha1
Hash value: 75357805540739e7ab8846662277e1d43072f5f0
Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
Using 'config@hk09' configuration
Trying 'fdt@hk09' fdt subimage
Description: ARM OpenWrt qcom-ipq807x-hkxx device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x44518ac8
Data Size: 87902 Bytes = 85.8 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 7538e7fd
Hash algo: sha1
Hash value: 527f4c376e1dec7d4485647e75ba62d2782c37ba
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x44518ac8
Uncompressing Kernel Image ... OK
Loading Device Tree to 4a3e7000, end 4a3ff75d ... OK
Could not find PCI in device tree
Using machid 0x8010008 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.60 (chichen@arendelle) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 038aa3060+r49254) ) #12 SMP PREEMPT Fri Mar 19 16:12:43 CST 2021
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c0383d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ807x/AP-HK09
[ 0.000000] Ignoring memory range 0x40000000 - 0x41000000
[ 0.000000] Reserved memory: OVERLAP DETECTED!
[ 0.000000] wifi_dump@51100000 (0x51100000--0x51700000) overlaps with wigig_dump@51300000 (0x51300000--0x51700000)
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] PERCPU: Embedded 11 pages/cpu @be6ae000 s15168 r8192 d21696 u45056
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 226340
[ 0.000000] Kernel command line: console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 893980K/914432K available (6304K kernel code, 373K rwdata, 1908K rodata, 1024K init, 407K bss, 20452K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xbf800000 - 0xff800000 (1024 MB)
[ 0.000000] lowmem : 0x80000000 - 0xbf000000 (1008 MB)
[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
[ 0.000000] .text : 0x80208000 - 0x80b052d4 (9205 kB)
[ 0.000000] .init : 0x80c00000 - 0x80d00000 (1024 kB)
[ 0.000000] .data : 0x80d00000 - 0x80d5d748 ( 374 kB)
[ 0.000000] .bss : 0x80d60000 - 0x80dc5cfc ( 408 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000016] Switching to timer-based delay loop, resolution 52ns
[ 0.000770] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000782] pid_max: default: 32768 minimum: 301
[ 0.000872] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000882] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001400] Initializing cgroup subsys io
[ 0.001415] Initializing cgroup subsys memory
[ 0.001438] Initializing cgroup subsys devices
[ 0.001448] Initializing cgroup subsys freezer
[ 0.001458] Initializing cgroup subsys net_cls
[ 0.001467] Initializing cgroup subsys pids
[ 0.001477] Initializing cgroup subsys debug
[ 0.001499] CPU: Testing write buffer coherency: ok
[ 0.001913] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001960] Setting up static identity map for 0x41300000 - 0x41300058
[ 0.052816] MSM Memory Dump base table set up
[ 0.052841] MSM Memory Dump apps data table set up
[ 0.090177] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.120159] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.150191] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.150245] Brought up 4 CPUs
[ 0.150264] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.150270] CPU: All CPU(s) started in SVC mode.
[ 0.173881] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.174184] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.174206] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.174551] pinctrl core: initialized pinctrl subsystem
[ 0.175564] NET: Registered protocol family 16
[ 0.176649] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[ 0.200029] cpuidle: using governor ladder
[ 0.230048] cpuidle: using governor menu
[ 0.230269] NET: Registered protocol family 42
[ 0.231820] Soc version is not 1, changing clock offsets
[ 0.239535] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[ 0.242055] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[ 0.260707] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.260719] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.262560] CPU: IPQ8072A, SoC Version: 2.0
[ 0.263182] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[ 0.263548] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 0.264502] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[ 0.266163] IPC logging disabled
[ 0.266170] IPC logging disabled
[ 0.266175] IPC logging disabled
[ 0.266180] IPC logging disabled
[ 0.266185] IPC logging disabled
[ 0.266403] sps:sps is ready.
[ 0.302045] pps_core: LinuxPPS API ver. 1 registered
[ 0.302054] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.302085] PTP clock support registered
[ 0.303923] Advanced Linux Sound Architecture Driver Initialized.
[ 0.304737] clocksource: Switched to clocksource arch_sys_counter
[ 0.308703] NET: Registered protocol family 2
[ 0.309347] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.309432] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.309573] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.309624] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.309660] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.309827] NET: Registered protocol family 1
[ 0.311081] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.319424] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.319442] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.323196] Key type asymmetric registered
[ 0.323209] Asymmetric key parser 'x509' registered
[ 0.323240] io scheduler noop registered
[ 0.323251] io scheduler deadline registered (default)
[ 0.326046] 20000000.pci supply vdda not found, using dummy regulator
[ 0.326092] 20000000.pci supply vdda_phy not found, using dummy regulator
[ 0.326132] 20000000.pci supply vdda_refclk not found, using dummy regulator
[ 0.326761] PCI host bridge /soc/pci@20000000 ranges:
[ 0.326786] IO 0x20200000..0x2020ffff -> 0x20200000
[ 0.326801] MEM 0x20220000..0x2fffffff -> 0x20220000
[ 1.476428] qcom-pcie 20000000.pci: phy link never came up
[ 1.477986] qcom-pcie 20000000.pci: hostinit failed
[ 1.477996] qcom-pcie 20000000.pci: cannot initialize host
[ 1.478137] qcom-pcie: probe of 20000000.pci failed with error -110
[ 1.478309] 10000000.pci supply vdda not found, using dummy regulator
[ 1.478349] 10000000.pci supply vdda_phy not found, using dummy regulator
[ 1.478383] 10000000.pci supply vdda_refclk not found, using dummy regulator
[ 1.478899] PCI host bridge /soc/pci@10000000 ranges:
[ 1.478921] IO 0x10200000..0x1020ffff -> 0x10200000
[ 1.478934] MEM 0x10220000..0x1fffffff -> 0x10220000
[ 2.626430] qcom-pcie 10000000.pci: phy link never came up
[ 2.627988] qcom-pcie 10000000.pci: hostinit failed
[ 2.627997] qcom-pcie 10000000.pci: cannot initialize host
[ 2.628110] qcom-pcie: probe of 10000000.pci failed with error -110
[ 2.633589] msm_rpm_log_probe: OK
[ 2.633969] msm-dcc b3000.dcc: DCC XPU is not specified
[ 2.634216] msm-dcc b3000.dcc: jiffies_64: 0xffff8bd6, cntvct_64: 0x8f6b9a2
[ 2.634229] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xbfb3e004)
[ 2.634240] msm-dcc b3000.dcc: gcnt_lo: 0x08f6bb8b(0xbfb3e000)
[ 2.634981] TZ SMMU State: SMMU Stage2 Enabled
[ 2.635038] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[ 2.636876] msm_serial 78b3000.serial: msm_serial: detected port #0
[ 2.636915] msm_serial 78b3000.serial: uartclk = 3686400
[ 2.636950] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 22, base_baud = 230400) is a MSM
[ 2.636970] msm_serial: console setup on port #0
[ 3.439740] console [ttyMSM0] enabled
[ 3.444821] msm_serial: driver initialized
[ 3.448326] msm_serial_hsl_init: driver initialized
[ 3.461420] brd: module loaded
[ 3.462004] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 3.464312] spi_qup 78b8000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 3.472397] m25p80 spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff
[ 3.478508] QPIC controller hw version Major:1, Minor:5
[ 3.484070] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xa3
[ 3.489116] nand: Toshiba TH58NYG3S0H 8G 1.8V 8-bit
[ 3.495671] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 256
[ 3.500374] 26 ofpart partitions found on MTD device qcom_nand.0
[ 3.508257] Creating 26 MTD partitions on "qcom_nand.0":
[ 3.514236] 0x000000000000-0x000000100000 : "0:SBL1"
[ 3.520857] 0x000000100000-0x000000200000 : "0:MIBIB"
[ 3.525620] 0x000000200000-0x000000280000 : "0:BOOTCONFIG"
[ 3.530359] 0x000000280000-0x000000300000 : "0:BOOTCONFIG1"
[ 3.535788] 0x000000300000-0x000000600000 : "0:QSEE"
[ 3.542267] 0x000000600000-0x000000900000 : "0:QSEE_1"
[ 3.547509] 0x000000900000-0x000000980000 : "0:DEVCFG"
[ 3.551431] 0x000000980000-0x000000a00000 : "0:DEVCFG_1"
[ 3.556580] 0x000000a00000-0x000000a80000 : "0:APDP"
[ 3.562060] 0x000000a80000-0x000000b00000 : "0:APDP_1"
[ 3.566947] 0x000000b00000-0x000000b80000 : "0:RPM"
[ 3.571846] 0x000000b80000-0x000000c00000 : "0:RPM_1"
[ 3.576685] 0x000000c00000-0x000000c80000 : "0:CDT"
[ 3.581860] 0x000000c80000-0x000000d00000 : "0:CDT_1"
[ 3.586588] 0x000000d00000-0x000000d80000 : "0:APPSBLENV"
[ 3.591788] 0x000000d80000-0x000000e80000 : "0:APPSBL"
[ 3.597405] 0x000000e80000-0x000000f80000 : "0:APPSBL_1"
[ 3.602444] 0x000000f80000-0x000001000000 : "0:ART"
[ 3.607728] 0x000001000000-0x000007400000 : "rootfs"
[ 3.652810] mtd: device 18 (rootfs) set to be root filesystem
[ 3.653279] mtdsplit: no squashfs found in "rootfs"
[ 3.657551] 0x000007400000-0x000008c80000 : "0:WIFIFW"
[ 3.672847] 0x000008c80000-0x00000f080000 : "rootfs_1"
[ 3.714387] 0x00000f080000-0x000010900000 : "0:WIFIFW_1"
[ 3.725195] 0x000010900000-0x000010b40000 : "0:ETHPHYFW"
[ 3.726933] 0x000010b40000-0x000010c40000 : "0:board_data"
[ 3.730767] 0x000010c40000-0x000011440000 : "0:arc_datadump"
[ 3.738970] 0x000011440000-0x00003e000000 : "0:arc_data"
[ 4.033203] libphy: Fixed MDIO Bus: probed
[ 4.473998] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[ 4.474133] libphy: qca_mdio: probed
[ 4.480221] qca-mdio 90000.mdio: qca-mdio driver was registered
[ 4.482692] Unable to create IPC log context!
[ 4.488424] Skip QCA8074V1 in V2 platform
[ 4.492844] cnss: Platform driver probed successfully. plat bd8c5010 tgt 0xfffe
[ 4.496937] i2c /dev entries driver
[ 4.511740] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 4.512227] sdhci: Secure Digital Host Controller Interface driver
[ 4.519281] sdhci: Copyright(c) Pierre Ossman
[ 4.525266] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.530158] [ipq_led_probe(247)] ledc_base_addr:0xc08c0000, res->start:0x0191e000, res->end: 0x0193e06f
[ 4.535423] [ipq_led_probe(257)] qcom,tcsr_ledc_values:
[ 4.544497] write val_arr[0]: 0x00320193 to LEDC_ADDR(0): 0xc08e0040
[ 4.549721] write val_arr[1]: 0x00000000 to LEDC_ADDR(1): 0xc08e0044
[ 4.556317] write val_arr[2]: 0x00000000 to LEDC_ADDR(2): 0xc08e0048
[ 4.562729] write val_arr[3]: 0x00000000 to LEDC_ADDR(3): 0xc08e004c
[ 4.569162] write val_arr[4]: 0x00000000 to LEDC_ADDR(4): 0xc08e0050
[ 4.575586] write val_arr[5]: 0xffffffff to LEDC_ADDR(5): 0xc08e0054
[ 4.581999] write val_arr[6]: 0x00000000 to LEDC_ADDR(6): 0xc08e0058
[ 4.588433] write val_arr[7]: 0xffffffff to LEDC_ADDR(7): 0xc08e005c
[ 4.594856] write val_arr[8]: 0x007d0820 to LEDC_ADDR(8): 0xc08e0060
[ 4.601270] write val_arr[9]: 0x00000000 to LEDC_ADDR(9): 0xc08e0064
[ 4.607704] write val_arr[10]: 0x10482094 to LEDC_ADDR(10): 0xc08e0068
[ 4.614118] write val_arr[11]: 0x03ffffe1 to LEDC_ADDR(11): 0xc08e006c
[ 4.620550] [ipq_led_probe(263)]
[ 4.627143] [ipq_led_probe(271)] qcom,ledc_blink_indices_cnt: 15, MAX_BLINK_IDX: 15
[ 4.630617] [ipq_led_probe(322)] led(0) active(1)
[ 4.637997] [ipq_led_probe(322)] led(1) active(1)
[ 4.642847] [ipq_led_probe(322)] led(2) active(1)
[ 4.647543] [ipq_led_probe(322)] led(3) active(0)
[ 4.652221] [ipq_led_probe(322)] led(4) active(0)
[ 4.656920] [ipq_led_probe(322)] led(5) active(1)
[ 4.661596] [ipq_led_probe(322)] led(6) active(1)
[ 4.666295] [ipq_led_probe(322)] led(7) active(1)
[ 4.670971] [ipq_led_probe(322)] led(8) active(1)
[ 4.675669] [ipq_led_probe(322)] led(9) active(1)
[ 4.680345] [ipq_led_probe(322)] led(10) active(1)
[ 4.685044] [ipq_led_probe(322)] led(11) active(1)
[ 4.689720] [ipq_led_probe(322)] led(12) active(0)
[ 4.694496] [ipq_led_probe(322)] led(13) active(1)
[ 4.699281] [ipq_led_probe(322)] led(14) active(0)
[ 4.705761] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[ 4.708879] ICE IRQ = 26
[ 4.717662]
[ 4.717662] Version Rollback Feature Disabled
[ 4.720404] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x08b04000
[ 4.725512] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x08b04000
[ 4.741394] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x08b04000
[ 4.755883] sps:BAM 0x08b04000 is registered.[ 4.765092] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss
[ 4.766645] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available
[ 4.775893] SPMI VADC - Min ch: 0 Max ch: 15
[ 4.783675] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[ 4.786456] coresight-csr 6001000.csr: CSR initialized
[ 4.793893] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[ 4.798876] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[ 4.806423] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[ 4.813788] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[ 4.821176] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[ 4.828561] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[ 4.835935] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[ 4.843306] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[ 4.850695] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[ 4.858079] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[ 4.865453] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[ 4.872799] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[ 4.880188] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[ 4.887568] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[ 4.894946] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[ 4.902308] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[ 4.909712] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[ 4.917230] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[ 4.924580] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
[ 4.932024] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
[ 4.939449] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[ 4.946795] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06044000
[ 4.953792] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06044000
[ 4.969512] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06044000
[ 4.983996] sps:BAM 0x06044000 is registered.[ 4.991027] coresight-tmc 6028000.tmc: TMC initialized
[ 4.995139] coresight-tmc 6027000.tmc: TMC initialized
[ 5.000242] coresight-funnel 6021000.funnel: FUNNEL initialized
[ 5.005273] coresight-funnel 6100000.funnel: FUNNEL initialized
[ 5.011066] coresight-funnel 6120000.funnel: FUNNEL initialized
[ 5.016983] coresight-funnel 6130000.funnel: FUNNEL initialized
[ 5.022889] coresight-funnel 61a1000.funnel: FUNNEL initialized
[ 5.029531] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[ 5.035146] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[ 5.041091] coresight-etm4x 619e000.etm: ETM 4.0 initialized
[ 5.046821] coresight-etm4x 619f000.etm: ETM 4.0 initialized
[ 5.051903] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
[ 5.057692] coresight-stm 6002000.stm: STM initialized
[ 5.066453] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[ 5.070057] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[ 5.097667] NET: Registered protocol family 10
[ 5.098433] NET: Registered protocol family 17
[ 5.101036] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 5.105492] Bridge firewalling registered
[ 5.118203] 8021q: 802.1Q VLAN Support v1.8
[ 5.122376] Registering SWP/SWPB emulation handler
[ 5.127215] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[ 5.131113] pmd9655_s4: supplied by e-smps1-reg
[ 5.138347] cpr3_mem_acc_init: npu: not using memory accelerator regulator
[ 5.142581] npu_corner: fused NOM: open-loop= 808000 uV
[ 5.149555] npu_corner: fused TURBO: open-loop= 880000 uV
[ 5.155416] npu_corner: fused NOM: open-loop= 808000 uV
[ 5.160978] npu_corner: fused TURBO: open-loop= 880000 uV
[ 5.166664] npu_corner: Normal and Cold condition init done. Default to normal.
[ 5.172586] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[ 5.179427] pmd9655_s3: supplied by e-smps1-reg
[ 5.186744] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[ 5.191104] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[ 5.197718] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[ 5.205379] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[ 5.212880] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[ 5.222020] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 720000 uV
[ 5.228968] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 848000 uV
[ 5.238950] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 912000 uV
[ 5.248759] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop=1016000 uV
[ 5.258645] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 705, quot_offset[ 7]= 0
[ 5.268383] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 932, quot_offset[ 7]= 225
[ 5.279232] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1032, quot_offset[ 7]= 100
[ 5.290169] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1200, quot_offset[ 7]= 165
[ 5.301226] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[ 5.313126] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[ 5.318945] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[ 5.326212] ubi0: attaching mtd18
[ 5.345879] random: nonblocking pool is initialized
[ 5.688946] ubi0: scanning is finished
[ 5.694418] ubi0: attached mtd18 (name "rootfs", size 100 MiB)
[ 5.694436] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 5.699141] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 5.705994] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 5.712847] ubi0: good PEBs: 400, bad PEBs: 0, corrupted PEBs: 0
[ 5.719620] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 5.725874] ubi0: max/mean erase counter: 13/3, WL threshold: 4096, image sequence number: 2131456819
[ 5.732904] ubi0: available PEBs: 0, total reserved PEBs: 400, PEBs reserved for bad PEB handling: 80
[ 5.742202] ubi0: background thread "ubi_bgt0d" started, PID 123
[ 5.752226] hctosys: unable to open rtc device (rtc0)
[ 5.762118] pmd9655_ldo11: disabling
[ 5.762814] ALSA device list:
[ 5.766092] No soundcards found.
[ 5.771565] VFS: Mounted root (squashfs filesystem) readonly on device 31:27.
[ 5.773275] Freeing unused kernel memory: 1024K (80c00000 - 80d00000)
[ 6.026661] init: Console is alive
[ 6.026739] init: - watchdog -
[ 7.116909] usbcore: registered new interface driver usbfs
[ 7.116953] usbcore: registered new interface driver hub
[ 7.121357] usbcore: registered new device driver usb
[ 7.127801] Button Hotplug driver version 0.4.1
[ 7.133329] exFAT: Version 1.2.9
[ 7.140812] SCSI subsystem initialized
[ 7.147589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.147875] ehci-platform: EHCI generic platform driver
[ 7.159503] msm-usb-ssphy-qmp 78000.ssphy: Initializing QMP phy
[ 7.166713] msm-usb-ssphy-qmp 78000.ssphy: QMP PHY initialization timeout
[ 7.166734] msm-usb-ssphy-qmp 78000.ssphy: USB3_PHY_PCS_STATUS:68686868
[ 7.373523] msm-usb-ssphy-qmp 58000.ssphy: Initializing QMP phy
[ 7.381497] msm-usb-ssphy-qmp 58000.ssphy: QMP PHY initialization timeout
[ 7.381518] msm-usb-ssphy-qmp 58000.ssphy: USB3_PHY_PCS_STATUS:68686868
[ 7.591091] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 7.591126] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 7.595646] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
[ 7.603045] xhci-hcd xhci-hcd.0.auto: irq 226, io mem 0x08a00000
[ 7.612018] hub 1-0:1.0: USB hub found
[ 7.617960] hub 1-0:1.0: 1 port detected
[ 7.621653] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 7.625609] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 7.630904] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.638677] hub 2-0:1.0: USB hub found
[ 7.646773] hub 2-0:1.0: 1 port detected
[ 7.650454] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.654407] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 7.659822] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
[ 7.667278] xhci-hcd xhci-hcd.1.auto: irq 227, io mem 0x08c00000
[ 7.676149] hub 3-0:1.0: USB hub found
[ 7.682183] hub 3-0:1.0: 1 port detected
[ 7.685849] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 7.689821] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 7.695143] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.702873] hub 4-0:1.0: USB hub found
[ 7.711008] hub 4-0:1.0: 1 port detected
[ 7.717719] usbcore: registered new interface driver usb-storage
[ 7.719070] usbcore: registered new interface driver uas
[ 8.029363] init: - preinit -
[07_lxc_cgroup_mounts]
[07_lxc_cgroup_mounts/lxc_cgroup_v2_mount]
mount: mounting cgroup on /sys/fs/cgroup/net_cls,net_prio failed: No such file or directory
mount: mounting cgroup on /sys/fs/cgroup/perf_event failed: No such file or directory
mount: mounting fusectl on /sys/fs/fuse/connections/ failed: No such file or directory
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
Before mount_root
[ 10.298145] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 185
[ 10.353295] UBIFS (ubi0:2): recovery needed
[ 10.473944] UBIFS (ubi0:2): recovery completed
[ 10.474012] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 10.477296] UBIFS (ubi0:2): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 10.485198] UBIFS (ubi0:2): FS size: 26664960 bytes (25 MiB, 105 LEBs), journal size 2031617 bytes (1 MiB, 6 LEBs)
[ 10.495106] UBIFS (ubi0:2): reserved for root: 1259451 bytes (1229 KiB)
[ 10.505328] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID CD97E20F-B93E-41BB-9F04-16883E36367F, small LPT model
[ 10.520439] mount_root: switching to jffs2 overlay
After mount_root
12064+0 records in
12064+0 records out
12064 bytes (11.8KB) copied, 0.024288 seconds, 485.1KB/s
131072+0 records in
131072+0 records out
131072 bytes (128.0KB) copied, 0.236178 se[ 10.817863] procd: - early -
[ 10.819792] procd: - watchdog -
conds, 542.0KB/s
SPATH=[/sys/devices/virtual/tty/tty/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/virtual/tty/tty]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[--]:[//]:::
[BaseClass]:[PCIDEV]=[]:[]
/sbin/hotplug-call: \:\:\: interfacce //.!
/sbin/hotplug-call: interfacce //.! not Supported.!
SPATH=[/sys/devices/virtual/tty/console/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/virtual/tty/console]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[--]:[//]:::
[BaseClass]:[PCIDEV]=[]:[]
/sbin/hotplug-call: \:\:\: interfacce //.!
/sbin/hotplug-call: interfacce //.! not Supported.!
SPATH=[/sys/devices/platform/soc/78b3000.serial/tty/ttyMSM0/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/platform/soc/78b3000.serial/tty/ttyMSM0]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[--]:[//]:::
[BaseClass]:[PCIDEV]=[]:[]
/sbin/hotplug-call: \:\:\: interfacce //.!
/sbin/hotplug-call: interfacce //.! not Supported.!
[ 11.441889] procd: - ubus -
[ 12.444630] procd: - init -
Please press Enter to activate this console.
[ 13.561540] ubi1: attaching mtd19
[ 13.651483] ubi1: scanning is finished
[ 13.657063] ubi1: attached mtd19 (name "0:WIFIFW", size 24 MiB)
[ 13.657082] ubi1: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 13.661778] ubi1: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 13.668734] ubi1: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 13.675584] ubi1: good PEBs: 98, bad PEBs: 0, corrupted PEBs: 0
[ 13.682348] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 13.688259] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 17045082
[ 13.695553] ubi1: available PEBs: 5, total reserved PEBs: 93, PEBs reserved for bad PEB handling: 80
[ 13.704498] ubi1: background thread "ubi_bgt1d" started, PID 1119
WIFI FW mount is successful
[mount_arc_partition0] MTD_PART:mtd25, mtd_data_part_index:25[ 14.137582] ubi2: attaching mtd25
[mount_arc_partition0] ubiattach /dev/ubi_ctrl -m 25
[ 16.775666] ubi2: scanning is finished
[ 16.782276] ubi2: attached mtd25 (name "0:arc_data", size 715 MiB)
[ 16.782300] ubi2: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 16.787369] ubi2: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 16.794197] ubi2: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 16.801062] ubi2: good PEBs: 2859, bad PEBs: 4, corrupted PEBs: 0
[ 16.807830] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 16.814079] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3924871397
[ 16.821204] ubi2: available PEBs: 0, total reserved PEBs: 2859, PEBs reserved for bad PEB handling: 76
[ 16.830499] ubi2: background thread "ubi_bgt2d" started, PID 1181
[mount_arc_partition0] volume name, MTD_PART:mtd30, mtd_ubi_data[ 16.854063] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1188
_part_index:30
[ 16.908227] UBIFS (ubi2:0): recovery needed
[ 16.974141] UBIFS (ubi2:0): recovery completed
[ 16.974199] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "arc-data"
[ 16.977479] UBIFS (ubi2:0): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 16.985048] UBIFS (ubi2:0): FS size: 702177280 bytes (669 MiB, 2765 LEBs), journal size 33521664 bytes (31 MiB, 132 LEBs)
[ 16.995017] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[ 17.005947] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID FA48C9B6-D1EF-4C1C-8ECE-CCD3A36455B8, small LPT model
[mount_arc_partition1] MTD_PART:, mtd_data_part_index:
[mount_arc_partition2] MTD_PART:, mtd_data_part_index:
[ 17.065582] cfg80211: World regulatory domain updated:
[ 17.065605] cfg80211: DFS Master region: unset
[ 17.069602] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 17.074214] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.084087] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 17.096163] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 17.104771] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.106156] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 17.113883] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 17.127529] Initializing XFRM netlink socket
[ 17.133529] NET: Registered protocol family 15
[ 17.138059] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 17.141572] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.149847] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 17.980463] ssdk_switch_device_num_init[1084]:INFO:ess-switch dts node number: 1
[ 17.984159] ssdk_dt_get_switch_node[919]:INFO:ess-switch DT exist!
[ 17.991164] ssdk_dt_parse_access_mode[820]:INFO:switch_access_mode: local bus
[ 17.997332] ssdk_dt_parse_access_mode[833]:INFO:switchreg_base_addr: 0x3a000000
[ 18.004441] ssdk_dt_parse_access_mode[834]:INFO:switchreg_size: 0x1000000
[ 18.011733] ssdk_dt_parse_mac_mode[288]:INFO:mac mode = 0x0
[ 18.018162] ssdk_dt_parse_mac_mode[297]:INFO:mac mode1 = 0xff
[ 18.023711] ssdk_dt_parse_mac_mode[306]:INFO:mac mode2 = 0xf
[ 18.029451] ssdk_dt_parse_phy_info[639]:INFO:[PORT 6] port_mac_sel = QGMAC_PORT
[ 18.035102] ssdk_dt_parse_uniphy[325]:INFO:ess-uniphy DT exist!
[ 18.042448] ssdk_dt_parse_intf_mac[766]:INFO:dp1 MAC ec:6c:9a:b8:33:ba
[ 18.048299] ssdk_dt_parse_intf_mac[766]:INFO:dp2 MAC ec:6c:9a:b8:33:ba
[ 18.054811] ssdk_dt_parse_intf_mac[766]:INFO:dp3 MAC ec:6c:9a:b8:33:ba
[ 18.061315] ssdk_dt_parse_intf_mac[766]:INFO:dp4 MAC ec:6c:9a:b8:33:ba
[ 18.067830] ssdk_dt_parse_intf_mac[766]:INFO:dp5 MAC ec:6c:9a:b8:33:ba
[ 18.074336] ssdk_dt_parse_intf_mac[766]:INFO:dp6 MAC ec:6c:9a:b8:33:ba
[ 18.080841] ssdk_plat_init start
[ 18.156467] ssdk_gcc_clock_init[629]:INFO:SSDK gcc clock init successfully!
[ 18.159640] ssdk_probe[1922]:INFO:ess_rst doesn't exist!
[ 18.166248] HPPE initializing...
[ 18.167692] malibu_phy_api_ops_init[2849]:INFO:qca probe malibu phy driver succeeded!
[ 18.178660] qca808x_phy_api_ops_init[2155]:INFO:qca probe qca808x phy driver succeeded!
[ 18.183766] qca808x_ptp_register[1410]:INFO:qca808x ptp clock registered
[ 18.190706] regi_init[3368]:INFO:Initializing HPPE!!
[ 18.414731] ssdk_ppe_reset_init[860]:INFO:ppe reset successfully!
[ 18.420655] qca_hppe_tdm_hw_init[674]:INFO:tdm setup num=96
[ 18.424049] qca_hppe_portctrl_hw_init[105]:INFO:Hawkeye PPE port initializing
[ 19.771800] ssdk_switch_register[1631]:INFO:Chip version 0x1500
[ 19.774797] qca_link_polling_select[1281]:INFO:link-polling-required node does not exist
[ 19.781024] ssdk_switch_register[1656]:INFO:polling is selected
[ 19.788754] regi_init[3372]:INFO:Initializing HPPE Done!!
[ 19.793669] regi_init[3423]:INFO:qca-ssdk module init succeeded!
[ 19.803314] tun: Universal TUN/TAP device driver, 1.6
[ 19.803336] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 19.810141] EDMA ver 1 hw init
[ 19.813625] EDMA HW Reset completed succesfully
[ 19.816502] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[ 19.820875] RxDesc:1 (15-15) RxFill:1 (7-7)
[ 20.030141] **********************************************************
[ 20.030165] * NSS Data Plane driver
[ 20.035553] **********************************************************
[ 20.044596] l2tp_core: L2TP core driver, V2.0
[ 20.045899] l2tp_netlink: L2TP netlink interface
[ 20.168644] nss_driver - fw of size 739856 bytes copied to load addr: 40000000, nss_id : 0
[ 20.169829] Supported Frequencies -
[ 20.175831] 748.8 MHz 1.4976 GHz
[ 20.181770] 1.6896 GHz [ 20.182814]
[ 20.185197] 7f7f34c0: set sdma bb45c700
[ 20.186705] 7f7f34c0: meminfo init succeed
[ 20.218882] node size 2 # items 4
[ 20.218904] memory: 40000000 1073741824 (avl 943013888) items 4 active_cores 2
[ 20.221214] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000
[ 20.228309] 7f7f34c0: nss core 0 booted successfully
[ 20.235902] nss_driver - fw of size 289392 bytes copied to load addr: 40800000, nss_id : 1
[ 20.240969] Supported Frequencies -
[ 20.248365] 748.8 MHz 1.4976 GHz
[ 20.254317] 1.6896 GHz [ 20.255362]
[ 20.257747] 7f7f7a00: set sdma bb45c900
[ 20.259262] 7f7f7a00: meminfo init succeed
[ 20.265197] sit: IPv6 over IPv4 tunneling driver
[ 20.266138] node size 2 # items 4
[ 20.266141] memory: 40000000 1073741824 (avl 943013888) items 4 active_cores 2
[ 20.266164] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000
[ 20.266175] 7f7f7a00: nss core 1 booted successfully
[ 20.290375] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[ 20.298790] mhi_init Quectel_Linux_PCIE_MHI_Driver_V1.3.0.11
[ 20.301792] rmnet_nss_init(): initializing rmnet_nss
[ 20.309509] usbcore: registered new interface driver cdc_wdm
[ 20.314258] usbcore: registered new interface driver qmi_wwan_cei
[ 20.318879] rmnet_nss_init(): initializing rmnet_nss
[ 20.323984] usbcore: registered new interface driver qmi_wwan_q
[ 20.329435] gre: GRE over IPv4 demultiplexor driver
[ 20.335173] ip_gre: GRE over IPv4 tunneling driver
[ 20.340755] ip6_gre: GRE over IPv6 tunneling driver
[ 20.349318] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 20.353070] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 20.357985] rmnet_nss_init(): initializing rmnet_nss
[ 20.365565] nf_conntrack version 0.5.0 (13984 buckets, 55936 max)
[ 20.367129] nf_nat_net_init: ***** Start to alloc hashtable *****
[ 21.385465] Netfilter messages via NETLINK v0.30.
[ 21.386607] ip_set: protocol 6
[ 25.137275] QCA Hy-Fi multicast installation successfully
[ 26.046258] PPP generic driver version 2.4.2
[ 26.245316] nss_lag_init[354]:LAG Manager Installed
[ 26.675438] NET: Registered protocol family 24
[ 27.005652] PPTP driver version 0.8.5
[ 27.240266] diag: IPC Logging disabled
[ 27.240639] TRACK: P[0] PMask[4]
[ 27.242895] TRACK: P[1] PMask[4]
[ 27.246315] TRACK: P[2] PMask[4]
[ 27.249614] TRACK: P[3] PMask[4]
[ 27.252728] nik 4097 info->svc_id
[ 27.596082] QCA multicast snooping installed successfully
[ 27.816082] <NSS-CRYPTO>:module loaded Build_ID - 03/19/21, 13:20:08 SoC=ipq807x
[ 28.040460] cannot find nss-macsec0 node
[ 28.040500] nss-macsec1 DT exist!
[ 28.080982] cannot find nss-macsec2 node
[ 28.080995] nss_macsec init success
[ 30.555276] u32 classifier
[ 30.555293] input device check on
[ 30.556863] Actions configured
[ 30.925265] Mirror/redirect action on
[ 34.797879] fuse init (API version 7.23)
[ 34.977576] arp_tables: (C) 2002 David S. Miller
[ 34.979721] usbcore: registered new interface driver cdc_acm
[ 34.981251] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 34.987998] usbcore: registered new interface driver cdc_ether
[ 34.996170] usbcore: registered new interface driver cdc_ncm
[ 35.002583] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.009561] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 35.106632] ctnetlink v0.93: registering with nfnetlink.
[ 35.108260] nf_conntrack_rtsp v0.6.21 loading
[ 35.307121] nf_nat_rtsp v0.6.21 loading
[ 35.310635] PPP MPPE Compression module registered
[ 35.311725] usbcore: registered new interface driver qmi_wwan
[ 35.315813] usbcore: registered new interface driver rndis_host
[ 35.322296] usbcore: registered new interface driver usblp
[ 35.330259] usbcore: registered new interface driver usbserial
[ 35.331756] usbcore: registered new interface driver usbserial_generic
[ 35.337723] usbserial: USB Serial support registered for generic
[ 35.361162] xt_time: kernel timezone is -0000
[ 35.471076] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.503904] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.537304] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.570652] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.571400] vmap allocation for size 24576 failed: use vmalloc=<size> to increase size.
[ 35.579539] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.586062] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.593921] vmap allocation for size 49152 failed: use vmalloc=<size> to increase size.
[ 35.601998] usbcore: registered new interface driver option
[ 35.609497] usbserial: USB Serial support registered for GSM modem (1-port)
[ 35.615280] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 35.622570] usbcore: registered new interface driver qcserial
[ 35.629922] usbserial: USB Serial support registered for Qualcomm USB modem
qcawifi configuration is disable
[ 39.939843] configuring additional NSS pbufs
[ 39.966425] additional pbufs of size 9003008 got added to NSS
[ 39.982223] mem_manager: module license 'Proprietary' taints kernel.
[ 39.982249] Disabling lock debugging due to kernel taint
[ 40.019896] vmap allocation for size 24576 failed: use vmalloc=<size> to increase size.
[ 41.789854] alloc_vmap_area: 3 callbacks suppressed
[ 41.789877] vmap allocation for size 2887680 failed: use vmalloc=<size> to increase size.
[ 41.794229] vmap allocation for size 417792 failed: use vmalloc=<size> to increase size.
[ 41.863858] wlan: [1640:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50
[ 41.873946] vmap allocation for size 94208 failed: use vmalloc=<size> to increase size.
[ 41.874015] vmap allocation for size 28672 failed: use vmalloc=<size> to increase size.
******FW ini file not found******
******No cold_boot_support*****
[ 42.241532] vmap allocation for size 1339392 failed: use vmalloc=<size> to increase size.
[ 42.241897] vmap allocation for size 241664 failed: use vmalloc=<size> to increase size.
[ 42.407624] vmap allocation for size 737280 failed: use vmalloc=<size> to increase size.
[ 42.407853] vmap allocation for size 114688 failed: use vmalloc=<size> to increase size.
[ 42.420045] wlan: [1648:I:ANY] =======ol_if_register_wifi3_0==========
[ 42.420045]
[ 42.422855] wlan: [1648:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ca1a88fc
[ 42.430626] wlan: [1648:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_type 1
[ 42.442057] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss
[ 42.462904] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[ 43.333366] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up
[ 43.333428] wlan: [1648:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_type 1
[ 43.333837] rpmsg_dev_probe: No pm domain
[ 43.333984] rpmsg_dev_probe: No pm domain
[ 43.334902] cnss: QMI WLFW service connected, state: 0x1
[ 43.335094] cnss: device_id : 65534 mem mode : [0]
[ 43.335186] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, 7fda8dc4
[ 43.335887] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0x270, soc_id: 0xffffffff, fw_version: 0x220804a5, fw_build_timestamp: 2020-04-16 07:55, otp_version: 0x0 eeprom_caldata_read_timeout 0s
[ 43.335893] cnss: Downloading BDF: bdwlan.b270, size: 64
[ 43.335895] cnss: No board_id entry in device tree
[ 43.341386] cnss: BDF location : 0x4b0c0000
[ 43.341390] cnss: BDF IPQ8074/bdwlan.b270 size 131072
[ 43.341754] cnss: Downloading BDF: caldata.bin, size: 64
[ 43.341988] cnss: per device BDF location : 0x4b0e0000
[ 43.342066] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000
[ 43.424036] wlan: [1648:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe
[ 43.430889] wlan: [1648:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for device fffe
[ 43.439168] wlan: [1648:I:ANY] pld_ahb_wlan_enable: 699: cnss_mode: Mission mode
[ 43.456456] wlan: [1648:I:ANY] qca_napi_create: 364: qca_napi_create: napi instance 0 created on pipe 4
[ 43.456580] wlan: [1648:I:ANY] __ol_ath_attach: 3922: Allocated soc b7980500
[ 43.465546] wlan: [1648:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000
[ 43.472169] wlan: [1648:I:ANY] osif_nss_wifi_soc_setup: 192: nss-wifili:#1 register wifili function for soc
[ 43.483503] wlan: [1648:I:ANY] osif_nss_wifi_soc_setup: 204: nss register id -1 nss config 3 Target Type 18
[ 43.493312] wlan: [1648:I:ANY] __ol_ath_attach: 4129: dev name soc0
[ 43.503250] wlan: [1648:I:ANY] ol_ath_soc_attach: 7124: WMI attached. wmi_handle b86e2400
[ 43.509178] wlan: [1648:I:ANY] htc_wmi_init: 6134: htc_wmi_init() HT Create . b7864000
[ 43.517432] wlan: [1648:I:ANY] htc_wmi_init: 6141: htc_wmi_init() Skipping BMI Done.
[ 43.525327] wlan: [1648:I:ANY] htc_wmi_init: 6198: [htc_wmi_init:6198] host_enable 0 nss_nwifi_offload 0
[ 43.535867] wlan: [1648:I:ANY] ol_target_init_complete: 6320: CDP soc attach success
[ 43.542771] wlan: [1648:I:ANY] ol_target_init_complete: 6327: Soc attach success NSS config 0
[ 43.550546] wlan: [1648:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle b7864000, ep 2, value 1
[ 43.558962] wlan: [1648:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle b7864000, ep 3, value 1
[ 43.569170] wlan: [1409:I:TIF] HE_CAP Info = 1a08010d
[ 43.578307] wlan: [1409:I:TIF] Num HW modes = 1
[ 43.583340] wlan: [1409:I:TIF] Num PHY = 2
[ 43.587660] wlan: [1409:I:TIF] Preferred HW Mode = 1 Num Radios = 2
[ 43.591826] wlan: [1409:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes,
[ 43.598061] wlan: [1409:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 0 wireless modes = f97f9001
[ 43.606714] wlan: [1409:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes,
[ 43.615976] wlan: [1409:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 1 wireless modes = 680680c
[ 43.624565] wlan: [1409:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 0 wireless modes = f97f9001
[ 43.633885] wlan: [1409:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 1 wireless modes = 680688c
[ 43.644668] wlan: [1409:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 421: dfs_offload 1
[ 43.654690] wlan: [1409:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2850: dfs->dfs_psoc_idx: 0
[ 43.665020] wlan: [1409:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2856: dfs_soc_obj->num_dfs_privs: 1
[ 43.674640] wlan: [1409:E:QDF] SOC0_PDEV2161124360 creation failed
[ 43.684863] wlan: [1409:E:DIRECT_BUF_RX] target_if_direct_buf_pdev_debugfs_init: 325: error while creating direct_buf debugfs dir
[ 43.691131] wlan: [1409:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 393: Do not allocate DFS object for 2G, pdev_id = 1
[ 43.702915] wlan: [1409:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:0 wmi_handle:b86e2400
[ 43.722914] wlan: [1409:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 0 Number of peers = 529 vdevs = 17
[ 43.725014] wlan: [1409:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success
[ 43.735564] wlan: [1409:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:1 wmi_handle:bbf4b600
[ 43.746361] wlan: [1409:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 1 Number of peers = 529 vdevs = 17
[ 43.752882] wlan: [1409:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success
[ 43.863532] wlan: [1409:I:ANY] copy_fw_abi_version_tlv: 6960: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[ 44.083774] wlan: [1409:I:ANY] ready_extract_init_status_tlv: 9002: ready_extract_init_status_tlv:0
[ 44.083804] wlan: [1409:I:ANY] dp_peer_map_attach_wifi3: 9790: dp_peer_map_attach_wifi3 max_peers 1109, max_ast_index: 4112
[ 44.083804]
[ 44.091805] wlan: [1648:I:ANY] ol_ath_connect_htc: 1215: WMI is ready
[ 44.156389] wlan: [1648:E:TIF] target_if_lro_hash_config: 254: pdev with id 0 is NULL
[ 44.159409] wlan: [1648:E:TIF] target_if_lro_hash_config: 254: pdev with id 1 is NULL
[ 44.163451] wlan: [1648:I:ANY] ol_ath_soc_attach: 7215: connect HTC
[ 44.171037] wlan: [1648:I:ANY] ol_ath_soc_attach: 7216: bypasswmi : 0
[ 44.177097] wlan: [1648:I:ANY] ol_ath_soc_attach: 7290: ol_ath_soc_attach() UMAC attach .
[ 44.183739] wlan: [1648:I:ANY] ald_init_netlink NETLINK_KERNEL_CREATE FAILED
[ 44.183739]
[ 44.191869] wlan: [1648:I:ANY] __ol_ath_attach: 4242: pdev_netdev name wifi0
[ 44.200442] wlan: [1648:I:ANY] __ol_ath_attach: 4289: Skip txrx_pdev_attach_target
[ 44.207554] wlan: [1648:I:ANY] __ol_ath_attach: 4315: BURSTING enabled by default
[ 44.215010] wlan: [1648:I:ANY] ol_ath_pdev_attach: 9058: interface_id 0
[ 44.222483] wlan: [1648:I:TIF] ol_ath_pdev_regdmn_init: 7444: phy id = 0 Modes supported
[ 44.228912] wlan: [1648:I:TIF] ol_ath_pdev_regdmn_init: 7451: 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1
[ 44.237247] wlan: [1648:I:TIF] ol_ath_pdev_regdmn_init: 7460: Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4900, hi_5g = 6100
[ 44.247497] wlan: [1648:I:ANY] ol_ath_update_wireless_modes: 1344: wireless_modes = f97f9001 before update
[ 44.261809] wlan: [1648:I:ANY] ol_ath_update_wireless_modes: 1359: Wireless_modes = f97f9001 after update
[ 44.271532] wlan: [1648:I:ANY] ol_ath_update_ext_caps: 1932: 11ax 5G supported case
[ 44.281294] wlan: [1648:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[ 44.288735] wlan: [1648:I:ANY] acfg_attach: 3519: acfg_attach: 3519: Netlink socket created:b86a6400
[ 44.295237] wlan: [1648:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1
[ 44.305667] wlan: [1648:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 25
[ 44.312004] wlan: [0:I:ANY] ol_ath_pdev_attach: 9402: Set global_ic[1], ptr:c7d8592c
[ 44.319360] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(bbf4b404) Enabling DBDC Repeater 1
[ 44.327102] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(bbf4b404) is_primary 1
[ 44.327182] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[ 44.343789] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14622: twt enabled.
[ 44.343789]
[ 44.345165] wlan: [1648:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 542: cfg block channel list is empty
[ 44.345170] wlan: [1648:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3850: pdev_idx = 0 tx_desc_limit = 32768
[ 44.345182] wlan: [1648:I:ANY] osif_wrap_attach: 239: osif wrap attached
[ 44.345182]
[ 44.345185] wlan: [1648:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[ 44.345185]
[ 44.345189] wlan: [1648:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =b86e2e00 ic->ic_wrap_com=b86e2e00 &wrap_com->wc_devt=b86e2e00
[ 44.345189]
[ 44.345206] wlan: [1648:I:ANY] __ol_ath_attach: 4485: needed_headroom reservation 60
[ 44.345210] wlan: [1648:I:ANY] ol_ath_enable_fraglist: 3272: Enabled Fraglist bit for the radio wifi0 features 41
[ 44.345418] wlan: [1648:I:ANY] ieee80211_cfg80211_radio_attach: 11804: ic: 0xb5c40500, wdev: 0xb5c57cf0, wiphy: 0xb86a7160, netdev: 0xb5c40000
[ 44.345869] wlan: [1648:I:ANY] __ol_ath_attach: 4242: pdev_netdev name wifi1
[ 44.345882] wlan: [1648:I:ANY] __ol_ath_attach: 4289: Skip txrx_pdev_attach_target
[ 44.345884] wlan: [1648:I:ANY] __ol_ath_attach: 4315: BURSTING enabled by default
[ 44.345921] wlan: [1648:I:ANY] ol_ath_pdev_attach: 9058: interface_id 1
[ 44.345931] wlan: [1648:I:TIF] ol_ath_pdev_regdmn_init: 7444: phy id = 1 Modes supported
[ 44.345934] wlan: [1648:I:TIF] ol_ath_pdev_regdmn_init: 7451: 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1
[ 44.345940] wlan: [1648:I:TIF] ol_ath_pdev_regdmn_init: 7460: Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0
[ 44.345943] wlan: [1648:I:ANY] ol_ath_update_wireless_modes: 1344: wireless_modes = 680680c before update
[ 44.345946] wlan: [1648:I:ANY] ol_ath_update_wireless_modes: 1359: Wireless_modes = 680680c after update
[ 44.345949] wlan: [1648:I:ANY] ol_ath_update_ext_caps: 1940: 11ax 2G supported case
[ 44.346030] wlan: [1648:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[ 44.346132] wlan: [1648:I:ANY] acfg_attach: 3494: Offload using existing sock b86a6400
[ 44.346140] wlan: [1648:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1
[ 44.346321] wlan: [1648:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 11
[ 44.346342] wlan: [0:I:ANY] ol_ath_pdev_attach: 9402: Set global_ic[2], ptr:c7d8592c
[ 44.346347] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(bbf4bc04) Enabling DBDC Repeater 1
[ 44.346369] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(bbf4bc04) is_primary 0
[ 44.347925] wlan: [1648:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 542: cfg block channel list is empty
[ 44.347929] wlan: [1648:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3850: pdev_idx = 1 tx_desc_limit = 32768
[ 44.347943] wlan: [1648:I:ANY] osif_wrap_attach: 239: osif wrap attached
[ 44.347943]
[ 44.347946] wlan: [1648:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[ 44.347946]
[ 44.347950] wlan: [1648:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =b86e3000 ic->ic_wrap_com=b86e3000 &wrap_com->wc_devt=b86e3000
[ 44.347950]
[ 44.347964] wlan: [1648:I:ANY] __ol_ath_attach: 4485: needed_headroom reservation 60
[ 44.347968] wlan: [1648:I:ANY] ol_ath_enable_fraglist: 3272: Enabled Fraglist bit for the radio wifi1 features 41
[ 44.347979] wlan: [1648:I:ANY] wlan_cfg80211_init: 11678: Number of 2G channels: 11
[ 44.348105] wlan: [1648:I:ANY] ieee80211_cfg80211_radio_attach: 11804: ic: 0xb5c80500, wdev: 0xb5c97cf0, wiphy: 0xb16acd60, netdev: 0xb5c80000
[ 44.348487] wlan: [1648:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3819: Running with HW mode = 1
[ 44.348700] wlan: [1648:E:QLD] qld_register: 108: Handle or address is NULL
[ 44.348715] wlan: [1648:I:ANY] wlan_pdev_operation: 726: num_radios=1, wifi_radios[0].sc = b5c40500_radio_type = 2
[ 44.348719] wlan: [1648:I:ANY] wlan_pdev_operation: 726: num_radios=2, wifi_radios[1].sc = b5c80500_radio_type = 2
[ 44.348740] wlan: [1648:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/multi-bss)
[ 44.713010] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[ 44.722394] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14622: twt enabled.
[ 44.722394]
[ 44.762470] vmap allocation for size 577536 failed: use vmalloc=<size> to increase size.
[ 44.762661] vmap allocation for size 102400 failed: use vmalloc=<size> to increase size.
[ 44.777949] wlan: [1654:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ca270fc0
[ 44.778276] wlan: [1654:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi-bss)
No Direct-Attach chipsets found.
base addr => ec:6c:9a:b8:33:ba
wifi 5g addr => ec:6c:9a:b8:33:bb
wifi 2g addr => ec:6c:9a:b8:33:bc
acfg_tool: Issuing blocking call to wait for events
[arc-init-board] start
[arc_syslog] start
[arc-init-aldk] boot
[arc-init-aldk] start_service
[arc-init-aldk main] line 24
arca.dbus.mng: is ready
[midcore main] line 280
[find_glbcfg_pattern(237)] /etc/glbcfg.dft find pattern:000000=
[find_glbcfg_pattern(254)] /etc/glbcfg.dft check pattern result
[midcore main(294)] /etc/glbcfg.dft find patterh:000000=
[find_glbcfg_pattern(237)] /etc/config/.glbcfg find pattern:000000=
[find_glbcfg_pattern(247)] /etc/config/.glbcfg find pattern:zzzzzz=
[find_glbcfg_pattern(254)] /etc/config/.glbcfg check pattern result
[midcore main] get /etc/config/.glbcfg ok, line 306
[fix_glbcfg(197)]
[midcore main] /tmp/.arca-midcore.ok set ok, line 365
[midcore main] enter main_loop(), line 370
[cfg-patch-agent] run_fw_ver:0.02.02r, cfg_ver:0.02.02r
Try to load agent : /usr/agents/arca-autowandetect-agent.so
Try to load agent : /usr/agents/arca-hostapd-agent.so
Try to load agent : /usr/agents/arca-ltecommander-agent.so
Try to load agent : /usr/agents/arca-misc-agent.so
arca.dbus.ltecommander: agent start
Try to load agent : /usr/agents/arca-mngcore-agent.so
Try to load agent : /usr/agents/arca-mngcore_nblocking-agent.so
arca.dbus.ltecommander: is ready
agent_handler(414):arca.dbus.misc: is ready
Try to load agent : /usr/agents/arca-qos-agent.so
Try to load agent : /usr/agents/arca-tr69-agent.so
Try to load agent : /usr/agents/arca-udevd-agent.so
Try to load agent : /usr/agents/arca-upnp-agent.so
Try to load agent : /usr/agents/arca-upnpes-agent.so
Try to load agent : /usr/agents/arca-usbapp-agent.so
Try to load agent : /usr/agents/arca-wlan-agent.so
[arc-init-aldk main] end, line 123
[arc-init-cfg-sync] start
[init_sync_cfg] PATH=/usr/sbin:/usr/bin:/sbin:/bin:/usr/sbin/agent:/usr/sbin/action
[init_sync_cfg/load_board_data] load board parameters
[init_sync_cfg/load_board_data] basemac:ec:6c:9a:b8:33:ba
[init_sync_cfg/set_wan_mac] wan_basemac:EC:6C:9A:B8:33:BD
[init_sync_cfg/set_wan_mac] ARC_WAN_100_MACaddr:EC:6C:9A:B8:33:BD
[init_sync_cfg/set_wan_mac] ARC_WAN_101_MACaddr:EC:6C:9A:B8:33:BE
[init_sync_cfg/set_wan_mac] ARC_WAN_102_MACaddr:EC:6C:9A:B8:33:BF
[init_sync_cfg/set_wan_mac] ARC_WAN_103_MACaddr:EC:6C:9A:B8:33:C0
[init_sync_cfg/set_wan_mac] ARC_WAN_600_MACaddr:EC:6C:9A:B8:33:BD
[init_sync_cfg/set_wan_mac] ARC_WAN_601_MACaddr:EC:6C:9A:B8:33:BE
[init_sync_cfg/set_wan_mac] ARC_WAN_602_MACaddr:EC:6C:9A:B8:33:BF
[init_sync_cfg/set_wan_mac] ARC_WAN_603_MACaddr:EC:6C:9A:B8:33:C0
[interface-agent] lan all
/sbin/arc_lan_v6_uci.sh Delete IPv6 options in dhcp.lan
/sbin/arc_lan_v6_uci.sh Delete IPv6 options in network.lan
/sbin/arc_lan_v6_uci.sh Disable IPv6 on ARC_LAN_0
Cfg ID: ARC_LAN_x_MACaddr, Idx1: 1, Idx2: -1, Default value unexist!
Cfg ID: ARC_LAN_x_Enable, Idx1: 1, Idx2: -1, Default value unexist!
Cfg ID: ARC_LAN_x_Enable, Idx1: 1, Idx2: -1, Default value unexist!
Cfg ID: ARC_LAN_x_MACaddr, Idx1: 2, Idx2: -1, Default value unexist!
Cfg ID: ARC_LAN_x_Enable, Idx1: 2, Idx2: -1, Default value unexist!
Cfg ID: ARC_LAN_x_Enable, Idx1: 2, Idx2: -1, Default value unexist!
[interface-agent] wan all
[nc_update_wan_config(1015)] input_count: 1
[nc_update_wan_config(1016)] wantype=6, concur_wandevs=6
[nc_update_wan_config(1041)] wan_type 6 INTERFACE_WAN_MAX_NUM:3
[nc_set_wan_config(482)] wan600->ARC_WAN_xy_MACAddr:EC:6C:9A:B8:33:BD
[nc_set_wan_config(486)] wan600->ARC_WAN_xy_Enable:1
[nc_set_wan_config(492)] wan600->ARC_WAN_xy_IP4_Proto:dhcp, ret: 0
[nc_set_wan_config(508)] wan600->ARC_WAN_xy_VLAN_Tagging:0
[nc_set_wan_config(519)] the original wan600->ARC_WAN_xy_BASE_Ifname:rmnet_usb0.1, ret: 0 , line:519
[nc_set_wan_config(521)] wan600->ARC_WAN_xy_BASE_Ifname:rmnet_usb0.1, ret: 0
[nc_set_wan_config(570)] wan600->ARC_WAN_xy_TMP_Prev_PPA_Ifname:, ret: 1
[nc_set_wan_config(648)] wan0->macaddr: EC:6C:9A:B8:33:BD
[nc_set_wan_config(681)] wan600->ARC_WAN_xy_IP4_Addr:0.0.0.0, ret: 0, line:681
[nc_set_wan_config(687)] wan600->ARC_WAN_xy_IP4_Netmask:0.0.0.0, ret: 0, line:687
[nc_set_wan_config(693)] wan600->ARC_WAN_xy_IP4_Gateway:0.0.0.0, ret: 0, line:693
[nc_set_wan_config(698)] wan600->ARC_WAN_xy_IP4_DftRoute:1
[nc_set_wan_config(722)] [nc_set_wan_config] ret=0 wan_service:internet
[nc_set_wan_config(744)] wan600->ARC_WAN_xy_IP4_DNS_Auto:1
[nc_set_wan_config(777)] wan600->ARC_WAN_xy_MTU:1500
[nc_set_wan_config(907)] ARC_SYS_Hostname:mygateway, ret: 0
[nc_set_wan_config(914)] ARC_SYS_VENDOR_CLASS_ID:, ret: 0
[nc_set_wan_config(921)] ARC_WAN_600_DHCP_ClientID:, ret: 0
[nc_set_wan_config(928)] lan0->ARC_LAN_x_DomainName:gateway, ret: 0
[nc_set_wan_config(948)] wan600->ARC_WAN_xy_IP6_Proto:dhcp, ret: 0
[nc_set_wan_config(951)] wan600->IPv6->create_config
/sbin/arc_wan_v6_uci.sh Delete network.wan_v6_600
/sbin/arc_wan_v6_uci.sh Delete network.wan_600.ipv6
/sbin/arc_wan_v6_uci.sh Create network.wan_v6_600
/sbin/arc_wan_v6_uci.sh Disable ARC_WAN_600 DHCPv6 IA-NA/IA-PD requests
[nc_set_wan_config(482)] wan601->ARC_WAN_xy_MACAddr:EC:6C:9A:B8:33:BE
[nc_set_wan_config(486)] wan601->ARC_WAN_xy_Enable:1
[nc_set_wan_config(492)] wan601->ARC_WAN_xy_IP4_Proto:dhcp, ret: 0
[nc_set_wan_config(508)] wan601->ARC_WAN_xy_VLAN_Tagging:0
[nc_set_wan_config(519)] the original wan601->ARC_WAN_xy_BASE_Ifname:rmnet_usb0.2, ret: 0 , line:519
[nc_set_wan_config(521)] wan601->ARC_WAN_xy_BASE_Ifname:rmnet_usb0.2, ret: 0
[nc_set_wan_config(570)] wan601->ARC_WAN_xy_TMP_Prev_PPA_Ifname:, ret: 1
[nc_set_wan_config(648)] wan1->macaddr: EC:6C:9A:B8:33:BE
[nc_set_wan_config(681)] wan601->ARC_WAN_xy_IP4_Addr:0.0.0.0, ret: 0, line:681
[nc_set_wan_config(687)] wan601->ARC_WAN_xy_IP4_Netmask:0.0.0.0, ret: 0, line:687
[nc_set_wan_config(693)] wan601->ARC_WAN_xy_IP4_Gateway:0.0.0.0, ret: 0, line:693
[nc_set_wan_config(698)] wan601->ARC_WAN_xy_IP4_DftRoute:0
[nc_set_wan_config(722)] [nc_set_wan_config] ret=0 wan_service:tr69
[nc_set_wan_config(744)] wan601->ARC_WAN_xy_IP4_DNS_Auto:1
[nc_set_wan_config(777)] wan601->ARC_WAN_xy_MTU:1500
[nc_set_wan_config(907)] ARC_SYS_Hostname:mygateway, ret: 0
[nc_set_wan_config(914)] ARC_SYS_VENDOR_CLASS_ID:, ret: 0
[nc_set_wan_config(921)] ARC_WAN_601_DHCP_ClientID:, ret: 0
[nc_set_wan_config(928)] lan0->ARC_LAN_x_DomainName:gateway, ret: 0
[nc_set_wan_config(948)] wan601->ARC_WAN_xy_IP6_Proto:dhcp, ret: 0
[nc_set_wan_config(951)] wan601->IPv6->create_config
/sbin/arc_wan_v6_uci.sh Delete network.wan_v6_601
/sbin/arc_wan_v6_uci.sh Delete network.wan_601.ipv6
/sbin/arc_wan_v6_uci.sh Create network.wan_v6_601
/sbin/arc_wan_v6_uci.sh Disable ARC_WAN_601 DHCPv6 IA-NA/IA-PD requests
[nc_set_wan_config(482)] wan602->ARC_WAN_xy_MACAddr:EC:6C:9A:B8:33:BF
Cfg ID: ARC_WAN_xy_Enable, Idx1: 6, Idx2: 2, Default value unexist!
[nc_set_wan_config(486)] wan602->ARC_WAN_xy_Enable:0
[nc_set_wan_config(968)] wan602->IPv6->delete_config
/sbin/arc_wan_v6_uci.sh Delete network.wan_v6_602
/sbin/arc_wan_v6_uci.sh Delete network.wan_602.ipv6
Cfg ID: ARC_WAN_xy_VLAN_Tagging, Idx1: 6, Idx2: 2, Default value unexist!
Cfg ID: ARC_WAN_xy_BASE_Ifname, Idx1: 6, Idx2: 2, Default value unexist!
wlan-agent-main CMD_BOOT
<WIFI-INFO>[48.51][wireless_wps_action,2527] ARC_WLAN_5G_WPS_PINEnable=1
[arc-init-cfg-sync] end
[arc-init-bsp] start
[arc-init-bsp] setup mirror
initial all to disable
lan idx is 1, wan is 0, wan direction is 0
[arc-init-bsp] end
acfg_tool: Issuing blocking call to wait for events
[ 49.409902] alloc_vmap_area: 2 callbacks suppressed
[ 49.409930] vmap allocation for size 253952 failed: use vmalloc=<size> to increase size.
[ 49.413767] vmap allocation for size 65536 failed: use vmalloc=<size> to increase size.
[ 49.452745] ECM init
[ 49.452789] ECM database jhash random seed: 0x4708aa73
[ 49.465151] ECM init complete
lbd: stopping daemon
[ 50.013007] device eth0 entered promiscuous mode
[ 50.014179] br-lan: port 1(eth0) entered forwarding state
[ 50.016758] br-lan: port 1(eth0) entered forwarding state
[ 50.029447] device eth1 entered promiscuous mode
[ 50.029511] br-lan: port 2(eth1) entered forwarding state
[ 50.033187] br-lan: port 2(eth1) entered forwarding state
[ 50.044099] device eth2 entered promiscuous mode
[ 50.044155] br-lan: port 3(eth2) entered forwarding state
[ 50.048557] br-lan: port 3(eth2) entered forwarding state
[ 50.058530] device eth3 entered promiscuous mode
[ 50.059277] br-lan: port 4(eth3) entered forwarding state
[ 50.063900] br-lan: port 4(eth3) entered forwarding state
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need [ 50.074697] device eth5 entered promiscuous mode
[ 50.080094] br-lan: port 5(eth5) entered forwarding state
[ 50.080110] br-lan: port 5(eth5) entered forwarding state
space = 211699
lan_idx = 0, lan_ip = 192.168.0.1, lan_mask = 255.255.255.0, lan_net = 192.168.0.0, lan_prefix = 24
Modify (-A) arptables rules ...
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
lbd: stopping daemon
lbd: require both 2.4 GHz and 5 GHz to be configured. Aborting start.
No qca-mad module enabled
qcawifi qcawificfg80211 disable radio wifi0
[ 51.012628] br-lan: port 1(eth0) entered disabled state
[ 51.012846] br-lan: port 2(eth1) entered disabled state
[ 51.017022] br-lan: port 3(eth2) entered disabled state
[ 51.022143] br-lan: port 4(eth3) entered disabled state
[ 51.027387] br-lan: port 5(eth5) entered disabled state
qcawifi qcawificfg80211 disable radio wifi1
SPATH=[/sys/devices/virtual/net/miireg/../../../..]
[ 51.250096] mc_attach: enabled snooping on br-lan.
INTERFACE=[miireg]
SPATH=[/sys/devices/virtual/net/eth0/../../../..]
INTERFACE=[eth0]
SPATH=[/sys/devices/virtual/net/eth1/../../../..]
INTERFACE=[eth1]
[ 51.462593] sh (5115): drop_caches: 3
qcawifi qcawificfg80211: enable radio wifi0
SPATH=[/sys/devices/virtual/net/eth2/../../../..]
INTERFACE=[eth2]
SPATH=[/sys/devices/virtual/net/eth3/../../../..]
INTERFACE=[eth3]
success apply scope limit for proxy1
success apply scope limit for proxy1
SPATH=[/sys/devices/virtual/net/eth4/../../../..]
INTERFACE=[eth4]
[ 52.114953] vmap allocation for size 20480 failed: use vmalloc=<size> to increase size.
[ 52.157767] vmap allocation for size 24576 failed: use vmalloc=<size> to increase size.
[ 52.170047] osal_module.c:39 OSAL module_init OK
[ 52.170047]
SPATH=[/sys/devices/virtual/net/eth5/../../../..]
INTERFACE=[eth5]
[ 52.253291] vmap allocation for size 102400 failed: use vmalloc=<size> to increase size.
[arc-init-action] start
[arc-init-action] apply hostname:mygateway
SPATH=[/sys/devices/virtual/net/ip6tnl0/../../../..]
INTERFACE=[ip6tnl0]
find [/etc/openvpn_init_AtBooting]
[arc-init-action] end
[arca.dbus.mng -> arca.dbus.mngcore: (Action: sys_boot Param: {}) ["arca.dbus.mngcore:init_dnsmasq" "arca.dbus.mngcore:init_nfc" "arca.dbus.mngcore:init_usb_storage" "arca.dbus.ltecommander:CMD_BOOT" "arca.dbus.mngcore:init_action" "arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.mngcore received: ["arca.dbus.mngcore:init_dnsmasq" "arca.dbus.mngcore:init_nfc" "arca.dbus.mngcore:init_usb_storage" "arca.dbus.ltecommander:CMD_BOOT" "arca.dbus.mngcore:init_action" "arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
SPATH=[/sys/devices/virtual/net/sit0/../../../..]
INTERFACE=[sit0]
[arca.dbus.mngcore -> arca.dbus.ltecommander: ["arca.dbus.ltecommander:CMD_BOOT" "arca.dbus.mngcore:init_action" "arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.ltecommander received: ["arca.dbus.ltecommander:CMD_BOOT" "arca.dbus.mngcore:init_action" "arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc[ 52.493267] vmap allocation for size 675840 failed: use vmalloc=<size> to increase size.
[ 52.497480] vmap allocation for size 69632 failed: use vmalloc=<size> to increase size.
:bootstatus CMD_SUCCESS"]]
command_handler:601: lte agent command_handler: argc = 1
command_handler:604: lte agent command_handler: COMMAND:[CMD_BOOT]
command_handler:609: Start-up ltecommander process...
open_ltecmd_shm:121: Never open before
SPATH=[/sys/devices/virtual/net/ifb0/../../../..]
INTERFACE=[ifb0]
SPATH=[/sys/devices/virtual/net/ifb1/../../../..]
INTERFACE=[ifb1]
[ 52.710829] (5549) <INF> project_profile_select(): select project:[Telstra_Hybrid]
[ 52.710912] (5549) <INF> project_profile_select(): platform:[XCI3544Z-SP-R0A]
[ 52.710970] (5549) <INF> get_file_hex_number() Hex:[08 00 01 08], num:0x08010008
[ 52.711009] (5549) <INF> project_profile_select(): machid:08010008
SPATH=[/sys/devices/virtual/net/gre0/../../../..]
INTERFACE=[gre0]
[ 52.720207] (5549) <INF> get_file_line() line:[console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M]
[ 52.720291] (5549) <INF> project_profile_select(): cmdline:[console=ttyMSM0,115200n8 pcie_dev=RG50 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M]
[ 52.720369] (5549) <INF> project_profile_select(): get default module sig:[RG50]
[ 52.720391] (5549) <INF> project_profile_select(): match mid:0x00000104
[ 52.720410] (5549) <INF> xci3544z_platform_init() HK-09-ql platform
[ 52.720428] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-HW-Power: 30
[ 52.723077] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-USB-VBus: 9
[ 52.727103] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-SW-Power: 54
[ 52.729033] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-Reset: 63
[ 52.738293] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-Emergency Boot: 16
[ 52.740153] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-Fly Mode: 0, ignore...
[ 52.740219] (5549) <INF> xci3544z_platform_init(XCI3544Z-R0A) GPIO-PIN-SIM Slot: 0, ignore...
SPATH=[/sys/devices/virtual/net/gretap0/../../../..]
INTERFACE=[gretap0]
[ 52.787302] (5549) <INF> xci3544z_platform_init() Platform init OK ...
[ 52.787333] (5549) <INF> project_profile_select(): bootarg:[RG50], dflt module:[RG50]/0x00000104
[ 52.787356] (5549) <INF> app_init() platform:[XCI3544Z-SP]/4, Ver:[R0A]/5, bootargsModule:[RG50]/0x00000104
[ 52.787434] (5549) <INF> GetInitCfgFromGui() Dflt at_fail_cnt_max:5
[ 52.787495] (5549) <INF> GetInitCfgFromGui() Dflt at_recover_cnt_max:3
[ 52.787537] (5549) <INF> GetInitCfgFromGui() Dflt upg_min_diff:400
[ 52.787577] (5549) <INF> GetInitCfgFromGui() Dflt fail_boot_dly:90
[ 52.787627] (5549) <INF> GetInitCfgFromGui() Dflt em_boot_dly:180
[ 52.787670] (5549) <INF> GetInitCfgFromGui() Dflt upg_cboot_recover_dly:120
[ 52.787719] (5549) <INF> GetInitCfgFromGui() Dflt upg_wboot_recover_dly:5
[ 52.787774] (5549) <INF> GetInitCfgFromGui() Dflt crash_reboot_dly:150
[ 52.787816] (5549) <INF> GetInitCfgFromGui() Dflt fwupg_complete_reboot:0
[ 52.787856] (5549) <INF> GetInitCfgFromGui() Dflt sms_func:1
[ 52.787893] (5549) <INF> GetInitCfgFromGui() Dflt pb_func:0
[ 52.787934] (5549) <INF> GetInitCfgFromGui() Dflt fwupg_bak_type:2
[ 52.787970] (5549) <INF> GetInitCfgFromGui() Dflt dflt_conf_try_cnt:10
[ 52.788006] (5549) <INF> GetInitCfgFromGui() Dflt dflt_conf_try_dly:5
[ 52.788042] (5549) <INF> GetInitCfgFromGui() Dflt tty2_usage:0x00000001
[ 52.789999] (5549) <INF> get_free_space(): cmd:[/arc-data/wwan_fw/fw_ok.tgz], val:-1
[ 52.814777] (5549) <INF> get_file_line() line:[638520]
[ 52.814842] (5549) <INF> get_free_space() val:-1, ret:0, buf:638520 KB
[ 52.814867] (5549) <INF> app_init() val:638520 KB, dflt_fw_sz(2x):327680 KB
[ 52.814893] (5549) <INF> app_init() free space enough !!
[ 52.814910] (5549) <INF> app_init() FW source path:[/arc-data/ww[ 53.065358] wlan: [5965:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 22
[ 53.069680] wlan: [5965:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=58
[ 53.077360] wlan: [5965:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=106
[ 53.085361] wlan: [5965:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=138
[ 53.094617] wlan: [5965:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 22
[ 53.102166] wlan: [5965:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=58
[ 53.109580] wlan: [5965:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=106
[ 53.117698] wlan: [5965:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 2621: ieee=138
[ 53.125973] wlan: [5965:I:ANY] number of channels: 2G = 0 5G = 22, 6G = 0
[ 53.134127] wlan: [5965:I:ANY] wlan_cfg80211_set_country: 6518: wlan_cfg80211_set_country: Country: AU ret: 0
[ 53.141264] wlan: [3189:I:ANY] ol_acfg_handle_wifi_ioctl: 446: ol_acfg_handle_wifi_ioctl: req->cmd=76 not valid for radio interface, it's for VAP
an_fw]
[ 52.815043] (5549) <INF> Entered LTE Commander
[ 52.815985] (5939) <INF> Leaving LTE Commander: return: 0
[ 52.816199] (5940) <INF> LTE Commander daemonized with PID: 5940
[ 52.816265] (5940) <INF> Event queue created
SPATH=[/sys/devices/virtual/net/ip6gre0/../../../..]
INTERFACE=[ip6gre0]
[ 52.877816] (5940) <INF> DBus handler started
[ 52.878140] (5940) <INF> gui_clear_voice_status() voice_status:Unknown
[ 52.878292] (5940) <INF> Init GUI ...
[ 52.881460] (5940) <INF> Init GUI ... OK
[ 52.881584] (5940) <INF> xci3544z_module_recover_chk() Module recover check, wan_type:6
[ 52.881606] (594[ 53.229766] wlan: [6306:I:ANY] ol_ath_set_config_param: 743: Resetting spectral chainmask to Rx chainmask
[ 53.229766]
0) <WRN> ltecommander():174 'module_recover_chk' need_recover:1
[ 52.881633] (5940) <INF> ltecommander() trigger FW-UPG timer after 120 secs
SPATH=[/sys/devices/virtual/net/bond0/../../../..]
INTERFACE=[bond0]
SPATH=[/sys/devices/virtual/net/ipsecdummy/../../../..]
INTERFACE=[ipsecdummy]
SPATH=[/sys/devices/virtual/net/teql0/../../../..]
INTERFACE=[teql0]
Error received: -22
Could not send NL command
SPATH=[/sys/devices/platform/soc/c000000.wifi1/net/wifi0/../../../..]
INTERFACE=[wifi0]
SPATH=[/sys/devices/platform/soc/c000000.wifi1/net/wifi1/../../../..]
INTERFACE=[wifi1]
SPATH=[/sys/devices/platform/soc/c000000.wifi1/net/soc0/../../../..]
INTERFACE=[soc0]
[ 53.313625] wlan: [6386:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 21
[ 53.313760] wlan: [6386:I:ANY] number of channels: 2G = 0 5G = 21, 6G = 0
SPATH=[/sys/devices/virtual/net/br-lan/../../../..]
INTERFACE=[br-lan]
[ 53.396869] wlan: [6481:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max_mac_rings 1
[ 53.396937] wlan: [6481:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max_mac_rings 1
[ 53.427334] wlan: [6516:I:ANY] wlan_cfg80211_set_hwaddr: 6591: wlan_cfg80211_set_hwaddr :ec:6c:9a:b8:33:bb ret: 0
[ 53.455955] wlan: [6544:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: value 100 wmi_status 0
[ 53.533422] wlan: [0:I:ANY] ol_ath_set_config_param: 2377: Disconnect_timeout value: 10
[ 53.560186] _TIC_initHw:465 create device
[ 53.560186]
[ 53.560213] _TIC_initHw:469 create channel
[ 53.560213]
[ 53.560873] wlan: [0:I:ANY] ol_ath_set_config_param: 2383: Reconfiguration_timeout value:60
[ 53.570100] _TIC_initHw:477 set control interface
[ 53.570100]
[ 53.578474] _TIC_initHw:493 wait for PCM clock ready
[ 53.578474]
[ 53.774789] _TIC_initHw:499 reset the SLIC
[ 53.774789]
number of vifs: cfg033579 cfg073579
command_handler:613: LTE module Power-ON
sendSignalValue2Ltecommander:340: sending SIGUSR1 signal with sival_int 25 to pid 5940......
[ 53.815768] (5940) <INF> BOOT signal
[arca.dbus.ltecommander -> arca.dbus.mngcore: ["arca.dbus.mngcore:init_action" "arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.mngcore received: ["arca.dbus.mngcore:init_action" "arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[init_action] start
[ 53.901820] (5940) <INF> sm_function_set() new cookie:1
[ 53.901914] (5940) <INF> sm_function_[ 53.911859] wlan: [7013:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath0 : clone params: 0x00000001
[ 53.916877] wlan: [7013:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create ec:6c:9a:b8:33:bb
[ 53.929028] wlan: [7013:I:ANY] wlan_vap_create: 1599: devhandle=0xb5c40500, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 53.929028]
[ 53.937304] wlan: [7013:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1
[ 53.948857] wlan: [7013:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0
[ 53.955808] wlan: [7013:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b
[ 53.971031] wlan: [7013:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[ 53.977912] wlan: [7013:I:ANY] MBO Initialized
[ 53.991940] wlan: [7013:I:ANY] OCE Initialized
[ 53.996250] wlan: [7013:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 31 nss_id -1
[ 54.000613] wlan: [7013:I:ANY] NSS radio_if 28
[ 54.010431] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0
[ 54.014583] wlan: [7013:I:ANY] osif_nss_ol_vap_create: 1393: vap create af4fd500 : if_num 31
[ 54.023137] wlan: [7013:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0
[ 54.031787] wlan: [7013:I:ANY] WLAN-NSS: VAP NSS ops initialized
[ 54.041193] wlan: [7013:I:ANY] VAP device ath0 created osifp: (af4fd500) os_if: (af5d0000)
set() Function:1
[ 53.901997] (5940) <INF> boot_device() vid/pid/ifnum/platform:0x0000/0x0000/0/XCI3544Z-SP(4)
[ 53.902021] (5940) <INF> boot_device() Platform:XCI3544Z-SP, Ver:R0A, Power-up control...
[ 53.902042] (5940) <INF> xci3544z_module_pre_boot() Reset off
[ 53.906537] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-63:1 completed !!
[ 53.906591] (5940) <INF> xci3544z_module_pre_boot() USB VBus off
[ 53.909262] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-9:1 completed !!
[ 53.911842] (5940) <INF> xci3544z_module_pre_boot() Module pre-boot OK ...
[ 53.911866] (5940) <INF> boot_device() set Module boot OK ...
[ 53.911911] (5940) <INF> misc_power() dbus_attrib:1
[ 53.916743] (5940) <INF> get_file_line() line:[0]
[ 53.932358] (5940) <INF> lte_gpio_in_ctrl() gpio-30() buf:[0], val:0
[ 53.932384] (5940) <WRN> xci3544z_power_state_set():138 LTE module R0A power set to ON
[ 53.936822] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-54:0 completed !!
[ 53.948548] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-30:1 completed !!
[arc-init-action] start wlan-agent
[wifi-scheduled-agent]
SPATH=[/sys/devices/virtual/net/ath0/../../../..]
INTERFACE=[ath0]
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need space = 211699
[ 54.274920] _TIC_initHw:505
[ 54.274920]
[ 54.275173] ID = 0xc3
[ 54.275173]
[ 54.278258] Revision Id 0x3 on channel 0
[ 54.278258]
[ 54.282248] _TIC_initHw:505
[ 54.282248]
[ 54.287585] ID = 0xc3
[ 54.287585]
[ 54.291819] Revision Id 0x3 on channel 1
[ 54.291819]
[ 54.295800] Si3226x_Init_with_Options(665) size = 2 init_opt = 0
[ 54.306583] SiVoice: Channel 0: Type = PROSLIC Rev = 3
[ 54.312696] SiVoice: Channel 1: Type = PROSLIC Rev = 3
[ 54.329301] ProSLIC:loading patch: 05262017
[ 54.866359] wlan: [7648:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:64
[ 54.986567] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-9:0 completed !!
[ 54.986645] (5940) <INF> xci3544z_power_state_set() Power on delay 3 secs
[ 55.082642] Si3226x: VBAT @ 50ms = 0.-209 v
[ 55.083718] Si3226x: DCDC Short Circuit Failure 0 - disabling channel
[ 55.153843] Si3226x: VBAT @ 50ms = 58.692 v
[ 55.218478] Si3226x: VBAT Up = 58.692 v
[ 55.340403] 8021q: adding VLAN 0 to HW filter on device ath0
[ 55.341253] device ath0 entered promiscuous mode
[ 55.345393] br-lan: port 6(ath0) entered forwarding state
[ 55.349774] br-lan: port 6(ath0) entered forwarding state
[ 55.381961] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3709: vap-0(ath0):ACS Params
[ 55.381994] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:30|chwidth:20|
[ 55.637921] wlan: [8187:E:ANY] ieee80211_ucfg_set_txpow: 1026: Exceeding Max Tx power of 23
[ 55.659932] wlan: [8216:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath02 : clone params: 0x00000001
[ 55.659997] wlan: [8216:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create f2:6c:9a:b8:33:bb
[ 55.671013] wlan: [8216:I:ANY] wlan_vap_create: 1599: devhandle=0xb5c40500, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 55.671013]
[ 55.679470] wlan: [8216:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1
[ 55.690962] wlan: [8216:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0
[ 55.698026] wlan: [8216:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b
[ 55.713347] wlan: [8216:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[ 55.720089] wlan: [8216:I:ANY] MBO Initialized
[ 55.734135] wlan: [8216:I:ANY] OCE Initialized
[ 55.738461] wlan: [8216:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 32 nss_id -1
[ 55.742872] wlan: [8216:I:ANY] NSS radio_if 28
[ 55.752624] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0
[ 55.756869] wlan: [8216:I:ANY] osif_nss_ol_vap_create: 1393: vap create bccfc500 : if_num 32
[ 55.765349] wlan: [8216:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0
[ 55.773776] wlan: [8216:I:ANY] WLAN-NSS: VAP NSS ops initialized
[ 55.783209] wlan: [8216:I:ANY] VAP device ath02 created osifp: (bccfc500) os_if: (bcdc8000)
[ 55.881228] Si3226x: : ProSLIC initialization completed.
SPATH=[/sys/devices/virtual/net/ath02/../../../..]
INTERFACE=[ath02]
[ 56.032202] ProSLIC:PCMStart
[ 56.184479] ProSLIC:PCMStart
[ 56.190307] Done the Silic Initialization
[ 56.190307]
[ 56.190335] _TIC_fxsSetLineState: oldState[-1,-1], state 13
[ 56.194840] _TIC_fxsSetLineState: oldState[-1,1], temp 1
[ 56.200450] _TIC_fxsSetLineState: oldState[-1,1], state 13
[ 56.205989] _TIC_fxsSetLineState: oldState[1,1], temp 1
[ 56.211294] 1646863115.704 [debug][vtsp]_vtspr_default.c:1988 dtmfConfig:
[ 56.211294]
[ 56.216265] 1646863115.709 [debug][vtsp]_vtspr_default.c:1990 pwr: -45, dur: 5, silence: 5 errFrame: 20
[ 56.216265]
[ 56.224576] 1646863115.717 [debug][vtsp]_vtspr_default.c:1992 HiTwist: 2, LoTwist: 2, dev 1
[ 56.224576]
[ 56.236104] 1646863115.729 [debug][vtsp]_vtspr_default.c:1988 dtmfConfig:
[ 56.236104]
[ 56.246228] 1646863115.739 [debug][vtsp]_vtspr_default.c:1990 pwr: -45, dur: 5, silence: 5 errFrame: 20
[ 56.246228]
[ 56.254295] 1646863115.747 [debug][vtsp]_vtspr_default.c:1992 HiTwist: 2, LoTwist: 2, dev 1
[ 56.254295]
[ 56.419309] wlan: [8645:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:8
[ 56.658781] 8021q: adding VLAN 0 to HW filter on device ath02
[ 56.659731] device ath02 entered promiscuous mode
[ 56.663661] br-lan: port 7(ath02) entered forwarding state
[ 56.668284] br-lan: port 7(ath02) entered forwarding state
[ 56.674407] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3709: vap-1(ath02):ACS Params
[ 56.679154] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:30|chwidth:20|
[ 56.806146] wlan: [9116:E:ANY] ieee80211_ucfg_set_txpow: 1026: Exceeding Max Tx power of 23
[ 56.841827] wlan: [9125:I:ANY] ol_ath_set_config_param: 2038: primary radio is set already for this radio
qcawifi qcawificfg80211: enable radio wifi1
[ 57.344755] br-lan: port 6(ath0) entered forwarding state
[ 57.380958] wlan: [9851:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 13
[ 57.381045] wlan: [9851:I:ANY] number of channels: 2G = 13 5G = 0, 6G = 0
[ 57.387626] wlan: [9851:I:ANY] wlan_cfg80211_set_country: 6518: wlan_cfg80211_set_country: Country: AU ret: 0
[ 57.466555] wlan: [9923:I:ANY] ol_ath_set_config_param: 743: Resetting spectral chainmask to Rx chainmask
[ 57.466555]
[ 57.587076] wlan: [10045:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max_mac_rings 1
[ 57.587143] wlan: [10045:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max_mac_rings 1
[ 57.618703] wlan: [10083:I:ANY] wlan_cfg80211_set_hwaddr: 6591: wlan_cfg80211_set_hwaddr :ec:6c:9a:b8:33:bc ret: 0
[ 57.645539] wlan: [10101:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: value 100 wmi_status 0
[ 57.725809] wlan: [0:I:ANY] ol_ath_set_config_param: 2377: Disconnect_timeout value: 10
[ 57.751032] wlan: [0:I:ANY] ol_ath_set_config_param: 2383: Reconfiguration_timeout value:60
[ 57.986771] (5940) <INF> xci3544z_power_state_set() trigger PWD_KEY pulse, isOn:1
[ 57.993453] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-54:0 completed !!
number of vifs: cfg0c3579 cfg103579
[ 58.024166] wlan: [10547:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath1 : clone params: 0x00000001
[ 58.024239] wlan: [10547:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create ec:6c:9a:b8:33:bc
[ 58.035537] wlan: [10547:I:ANY] wlan_vap_create: 1599: devhandle=0xb5c80500, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 58.035537]
[ 58.043802] wlan: [10547:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1
[ 58.055373] wlan: [10547:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0
[ 58.062837] wlan: [10547:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b
[ 58.077974] wlan: [10547:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[ 58.084790] wlan: [10547:I:ANY] MBO Initialized
[ 58.098909] wlan: [10547:I:ANY] OCE Initialized
[ 58.103325] wlan: [10547:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 33 nss_id -1
[ 58.107823] wlan: [10547:I:ANY] NSS radio_if 29
[ 58.117598] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0
[ 58.121893] wlan: [10547:I:ANY] osif_nss_ol_vap_create: 1393: vap create bce7a500 : if_num 33
[ 58.130477] wlan: [10547:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0
[ 58.138975] wlan: [10547:I:ANY] WLAN-NSS: VAP NSS ops initialized
[ 58.148838] wlan: [10547:I:ANY] VAP device ath1 created osifp: (bce7a500) os_if: (bcdf0000)
[ 58.098421] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-54:1 completed !!
[ 58.098508] (5940) <INF> on_off_pulse_trigger(R0A) pin-54 on/off pulse low delay 1200 msecs
SPATH=[/sys/devices/virtual/net/ath1/../../../..]
INTERFACE=[ath1]
[ 58.268609] 1646863117.762 [crit][vtsp]vtspr_task.c:143
[ 58.268609] D2 Technologies, Inc.
[ 58.268609] _ _ __
[ 58.268609] / | '/ /_ _ /_ _ _ /_ _ ._ _
[ 58.268609] /_.'/_ //_'/_ / // //_///_//_///_'_\
[ 58.268609] _/
[ 58.268609]
[ 58.268609] Unified Communication Products
[ 58.268609]
[ 58.283460] 1646863117.776 [crit][vtsp]vtspr_task.c:145 www.d2tech.com
[ 58.283460]
[ 58.305722] 1646863117.799 [crit][vtsp]vtspr_task.c:146 +D2Tech+ VTSP_RT ARC1_R_1_7_R09_RevUnversioned directory
[ 58.305722]
[ 58.314834]
[ 58.314834] D2 Technologies, Inc.
[ 58.314834] _ _ __
[ 58.314834] / | '/ /_ _ /_ _ _ /_ _ ._ _
[ 58.314834] /_.'/_ //_'/_ / // //_///_//_///_'_\
[ 58.314834] _/
[ 58.314834]
[ 58.314834] Unified Communication Products
[ 58.314834]
[ 58.339175] www.d2tech.com
[ 58.339175]
[ 58.361438] +D2Tech+ VTSP_RT ARC1_R_1_7_R09_RevUnversioned directory
[ 58.361438]
[ 58.664756] br-lan: port 7(ath02) entered forwarding state
[ 58.867888] wlan: [11245:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:64
[arc-init-action] There is no /etc/config/run_1905. If you need to run atdp, touch /etc/config/run_1905 and reboot.
[ 59.120452] 8021q: adding VLAN 0 to HW filter on device ath1
[ 59.121452] device ath1 entered promiscuous mode
[ 59.125340] br-lan: port 8(ath1) entered forwarding state
[ 59.129833] br-lan: port 8(ath1) entered forwarding state
[ 59.136221] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3709: vap-2(ath1):ACS Params
[ 59.140483] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20|
[ 59.291659] wlan: [11724:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath12 : clone params: 0x00000001
[ 59.291734] wlan: [11724:I:ANY] osifp_create_wlan_vap: 9618: VDEV Create f2:6c:9a:b8:33:bc
[ 59.305387] wlan: [11724:I:ANY] wlan_vap_create: 1599: devhandle=0xb5c80500, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 59.305387]
[ 59.311427] wlan: [11724:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1
[ 59.322917] wlan: [11724:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0
[ 59.330508] wlan: [11724:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b
[ 59.345534] wlan: [11724:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged
[ 59.352553] wlan: [11724:I:ANY] MBO Initialized
[ 59.366744] wlan: [11724:I:ANY] OCE Initialized
[ 59.370857] wlan: [11724:I:ANY] osif_nss_ol_vap_create: 1281: NSS wifi offload VAP create IF 34 nss_id -1
[ 59.375347] wlan: [11724:I:ANY] NSS radio_if 29
[ 59.385265] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1006: VDEV configuration success: 0
[ 59.389462] wlan: [11724:I:ANY] osif_nss_ol_vap_create: 1393: vap create bcda7500 : if_num 34
[ 59.398147] wlan: [11724:I:ANY] osif_create_vap_complete: 9826: TX Checksum:1|SG:1|TSO:1|LRO:0
[ 59.406520] wlan: [11724:I:ANY] WLAN-NSS: VAP NSS ops initialized
[ 59.415899] wlan: [11724:I:ANY] VAP device ath12 created osifp: (bcda7500) os_if: (bcf40000)
[ 59.302076] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-54:0 completed !!
[ 59.306520] (5940) <INF> check_em_boot() power-on OK, vid/pid/ifnum:0x0000/0x0000/0, dev_status:[Unknown]
[ 59.306552] (5940) <INF> check_em_boot() no device, trigger emergency boot after 180 secs
[ 59.308845] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms]... OK
[ 59.395936] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/evt]... OK
[ 59.412648] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/rd_n]... OK
[ 59.425024] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/rd]... OK
[ 59.426824] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/sd_n]... OK
[ 59.428607] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/sd]... OK
[ 59.438033] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/del]... OK
[ 59.443313] (5940) <INF> sms_env_setup() Setup SMS folder:[/arc-data/sms/misc]... OK
SPATH=[/sys/devices/virtual/net/ath12/../../../..]
INTERFACE=[ath12]
[ 60.132279] wlan: [12365:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:8
rzMemory start: 0x76856010, end 0x76BCC210, size 3629568
SIP CORE Test: argv[0] = /usr/sbin/arc-sip
[ 60.386743] 8021q: adding VLAN 0 to HW filter on device ath12
[ 60.387728] device ath12 entered promiscuous mode
[ 60.391831] br-lan: port 9(ath12) entered forwarding state
[ 60.396239] br-lan: port 9(ath12) entered forwarding state
[ 60.402506] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3709: vap-3(ath12):ACS Params
[ 60.407138] wlan: [3343:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20|
SIP CORE Test: main = 54ae9224
main=11750
Set the thread to name [main] This thread priority: 0 policy 0
SIP_CORE_Check_Emergency_Call_State: sip_emergency_call_exist(1) ==> new_state(0)
This thread priority: 0 policy 0
Set this thread to SCHED_RR and priority 15 result 0
Thread stack size = 81920 bytes
rzMemory start: 0x764C9010, end 0x7683F210, size 3629568
lbd: starting daemon
[ 60.864766] cpu_type: 389
[ 60.864766]
[ 60.864848] _TIC_fxsSetLineState: oldState[1,1], state 13
[ 60.867950] _TIC_fxsSetLineState: oldState[1,1], temp 1
[ 60.873554] _TIC_fxsSetLineState: oldState[1,1], state 13
[ 60.878502] _TIC_fxsSetLineState: oldState[1,1], temp 1
[ 61.124750] br-lan: port 8(ath1) entered forwarding state
******FW ini file not found******
[ 61.981330] wlan: [1645:I:ANY] vap-0(ath0): ACS result PCH 100 freq 5500, SCH 108 freq 5540, hw_mode 2 chwidth 80, vht_seg0 106 freq 5530, vht_seg1 0 freq 0
[ 61.981413] wlan: [1645:I:ANY] vap-1(ath02): ACS result PCH 100 freq 5500, SCH 108 freq 5540, hw_mode 2 chwidth 80, vht_seg0 106 freq 5530, vht_seg1 0 freq 0
[ 62.022858] wlan: [3343:I:ANY] DES SSID SET=TelstraB833BA
[ 62.022887] wlan: [3343:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 30
[ 62.027367] wlan: [3343:I:ANY] ieee80211_ucfg_set_freq_internal: 553:
[ 62.027367] Channel is configured already!!
[ 62.051786] wlan: [0:I:CMN_MLME] vdev[0] ieee chan:100 freq:5500
[ 62.051955] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 62.051955]
[ 62.054245] wlan: [3343:I:ANY] DES SSID SET=TELSTRA_BH_b833ba
[ 62.054249] wlan: [3343:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 30
[ 62.054309] wlan: [3343:I:ANY] ieee80211_ucfg_set_freq_internal: 553:
[ 62.054309] Channel is configured already!!
[ 62.054460] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel_for_freq: 879: dfs_curchan already updated
[ 62.090694] wlan: [0:I:ANY] vdev[0]: Mgt Rate:6000(kbps)
[ 62.101936] wlan: [0:I:CMN_MLME] vdev[1] ieee chan:100 freq:5500
[ 62.106952] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 62.106952]
[ 62.112875] wlan: [0:I:ANY] vdev[1]: Mgt Rate:6000(kbps)
[ 62.123418] wlan: [33:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5500.
[ 62.123418]
[ 62.128170] wlan: [33:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5520.
[ 62.128170]
[ 62.139142] wlan: [33:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5540.
[ 62.139142]
[ 62.151293] wlan: [33:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_START event delivered on chan freq 5560.
[ 62.151293]
[ 62.394756] br-lan: port 9(ath12) entered forwarding state
[ 63.323825] wlan: [1645:I:ANY] vap-2(ath1): ACS result PCH 1 freq 2412, SCH 5 freq 2432, hw_mode 1 chwidth 40, vht_seg0 3 freq 2422, vht_seg1 0 freq 0
[ 63.323907] wlan: [1645:I:ANY] vap-3(ath12): ACS result PCH 1 freq 2412, SCH 5 freq 2432, hw_mode 1 chwidth 40, vht_seg0 3 freq 2422, vht_seg1 0 freq 0
[ 63.350738] wlan: [3343:I:ANY] DES SSID SET=TelstraB833BA
[ 63.350769] wlan: [3343:I:ANY] wlan_cfg80211_chan_to_phymode: 1239: wlan_cfg80211_chan_to_phymode: band:0 width: 2 channel_cfreq: 2412 center_freq1: 2422 chandef.center_freq2: 0 flags: 0
[ 63.355842] wlan: [3343:I:ANY] ieee80211_ucfg_set_freq_internal: 553:
[ 63.355842] Channel is configured already!!
[ 63.394672] wlan: [3343:I:ANY] DES SSID SET=TELSTRA_BH_b833ba
[ 63.394701] wlan: [3343:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 26
[ 63.399630] wlan: [3343:I:ANY] ieee80211_ucfg_set_freq_internal: 553:
[ 63.399630] Channel is configured already!!
[ 63.475078] wlan: [0:I:CMN_MLME] vdev[2] ieee chan:1 freq:2412
[ 63.475267] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 63.475267] FD Interval should be a factor of BI.
[ 63.475267] Disabling FD
[ 63.475267]
[ 63.479966] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 63.479966] FD Interval should be a factor of BI.
[ 63.479966] Disabling FD
[ 63.479966]
[ 63.499927] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 63.499927]
[ 63.519817] wlan: [0:I:ANY] vdev[2]: Mgt Rate:1000(kbps)
[ 63.529591] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 63.529591]
[ 63.534986] wlan: [0:I:ANY] vdev[2]: Mgt Rate:1000(kbps)
[ 63.545489] wlan: [0:I:CMN_MLME] vdev[3] ieee chan:1 freq:2412
[ 63.550314] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 63.550314] FD Interval should be a factor of BI.
[ 63.550314] Disabling FD
[ 63.550314]
[ 63.555911] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 63.555911] FD Interval should be a factor of BI.
[ 63.555911] Disabling FD
[ 63.555911]
[ 63.575887] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 63.575887]
[ 63.595759] wlan: [0:I:ANY] vdev[3]: Mgt Rate:1000(kbps)
[ 63.605543] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 63.605543]
[ 63.610951] wlan: [0:I:ANY] vdev[3]: Mgt Rate:1000(kbps)
[arca.dbus.mngcore -> arca.dbus.tr69: ["arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.tr69 received: ["arca.dbus.tr69:CMD_BOOT" "arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.tr69 -> arca.dbus.misc: ["arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.misc received: ["arca.dbus.misc:telnetd CMD_BOOT" "arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.misc -> arca.dbus.mngcore: ["arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.mngcore received: ["arca.dbus.mngcore:route-agent CMD_START" "arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[route-agent] CMD_START
[arca.dbus.mngcore -> arca.dbus.upnp: ["arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.upnp received: ["arca.dbus.upnp:CMD_BOOT" "arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.upnp -> arca.dbus.usbapp: ["arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.usbapp received: ["arca.dbus.usbapp:CMD_SAMBA_RESTART" "arca.dbus.misc:bootstatus CMD_SUCCESS"]]
Trigger UP TR069 Module.
Key id=0x610e01ff
Message Q 0x18003 create
[arca.dbus.usbapp -> arca.dbus.misc: ["arca.dbus.misc:bootstatus CMD_SUCCESS"]]
[arca.dbus.misc received: ["arca.dbus.misc:bootstatus CMD_SUCCESS"]]
sh: uboot_env: not found
ACS server::URL: ["http://AW1000.arcadyan.cwmp.bdms.telstra.net/cwmp/cwmp"]
Periodic [Enabled]: Interval=[86400], Time=[2022-03-11T00:20:57Z]
manufacturer_name=[Arcadyan], manufacturer_oui=[EC6C9A], firmware_version=[0.02.02r build05-20201204], boot_version=[U-Boot 2016.01], hardware_version=[XCI35AX44Z-TA], serial_number=[ARC2204002079], model_name=[AW1000], product_code=[XCI35AX44Z-TA], description=[5GNR Router]
size Device_T = 131156
Register Device Successful
size Bridging_T = 27244
Register Bridging Successful
size Ethernet_T = 13132
Register function 0x54b4e228 to TR69_MSG_NONE!
Register Ethernet Successful
size SelfTestDiagnostics_T = 144
Register function 0x54b4e06c to TR69_MSG_NONE!
Register SelfTestDiagnostics Successful
size PPP_T = 4852
size IP_T = 22524
size Routing_T = 12828
size NeighborDiscovery_T = 228
size RouterAdvertisement_T = 776
size IPv6rd_T = 924
size DSLite_T = 972
Register function 0x54b597f8 to TR69_MSG_NONE!
Register function 0x54b50b88 to TR69_MSG_NONE!
Register PPP Successful
size DNS_T = 5988
size NAT_T = 18732
size DHCPv4_T = 9188
size DHCPv6_T = 17824
size Users_T = 224
Register function 0x54b612a0 to TR69_MSG_NONE!
Register function 0x54b5b950 to TR69_MSG_NONE!
Register DNS Successful
size QoS_T = 105440
Register function 0x54b6c6f8 to TR69_MSG_NONE!
Register QoS Successful
size USB_T = 2564
size Cellular_T = 10684
Register function 0x54b66614 to TR69_MSG_NONE!
Register function 0x54b66624 to TR69_MSG_NONE!
Register function 0x54b62624 to TR69_MSG_NONE!
Register USB Successful
size Firewall_T = 2532
size Security_T = 9440
Register function 0x54b67da0 to TR69_MSG_NONE!
Register function 0x54b6706c to TR69_MSG_NONE!
Register Firewall Successful
size DSL_T = 20392
size ATM_T = 5364
size PTM_T = 3708
Register DSL Successful
size WiFi_T = 100736
Register WiFi Successful
size BulkData_T = 410432
Register BulkData Successful
size Services_VoiceService_T[1] = 36084
Register InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.1.Line.1. Success
Register InternetGatewayDevice.Services.VoiceService.1.VoiceProfile.2.Line.1. Success
Register function 0x54b459b0 to TR69_MSG_NONE!
Register function 0x54b3ddb8 to TR69_MSG_NONE!
Register VoiceService Successful
size X_ARC_COM_T = 4
Register function 0x54b7a8a4 to TR69_MSG_NONE!
Register X_ARC_COM Successful
[arca.dbus.misc -> arca.dbus.mng: ["FWD_SUCCESS"]]
Not found Device.Ethernet.Link.3
Not found Device.IP.Interface.4
Can not open directory
ifconfig: eth.7: error fetching interface information: Device not found
ifconfig: rmnet_usb0.1: error fetching interface information: Device not found
sh: ethswctl: not found
sh: ethswctl: not found
sh: ethswctl: not found
sh: ethswctl: not found
Expecting msg length 21, is larger than buffer size 20
[MIDCORE-DEBUG]: mapi_opt_trans buffer size error action:[1], data:[ARC_WAN_600_DUID_Str]
Get DSL state fail!
Get DSL state fail!
ifconfig: ath11: error fetching interface information: Device not found
ifconfig: ath01: error fetching interface information: Device not found
get_RFPISIP
get_RFPISIP: [DECT_GetRFPI ]
link_SIP: g_aucRfpi 00-00-00-00-00
Read nLen = 1440
Total 134 Sync Functions!
Value = 5G
Value = 0.02.02r build05-20201204
CONN setting: /ConnectionRequest :51007, server_start=[0]
1
2
SSLAP_write_all_keys> create SSLAP_3RDCA_DATA successful.
SSLAP_write_all_keys> create SSLAP_VERISIGNCA_DATA successful.
SSLAP_write_all_keys> create SSLAP_server_CA_DATA successful.
SSLAP_write_all_keys> create SSLAP_server_PKCS12_DATA successful.
SSLAP_write_all_keys> create SSLAP_client_CA_DATA successful.
SSLAP_write_all_keys> create SSLAP_client_PKCS12_DATA successful.
SSLAP_load_all_key> read SSLAP_3RDCA_DATA success.
SSLAP_load_all_key> delete SSLAP_3RDCA_DATA.
SSLAP_load_all_key> read SSLAP_VERISIGNCA_DATA success.
SSLAP_load_all_key> delete SSLAP_VERISIGNCA_DATA.
SSLAP_load_all_key> read SSLAP_server_CA_DATA success.
SSLAP_load_all_key> delete SSLAP_server_CA_DATA.
SSLAP_load_all_key> read SSLAP_server_PKCS12_DATA success.
SSLAP_load_all_key> delete SSLAP_server_PKCS12_DATA.
SSLAP_load_all_key> read SSLAP_client_CA_DATA success.
SSLAP_load_all_key> delete SSLAP_client_CA_DATA.
SSLAP_load_all_key> read SSLAP_client_PKCS12_DATA success.
SSLAP_load_all_key> delete SSLAP_client_PKCS12_DATA.
[Init_SSLClient] Certificate_Id=0, nConnectProtocol=6
[Init_SSLClient] pSSLClientData->verify_peer=1
[sslc_conf_init] cert_array->verify_peer=1
[1988406596] [sslc_conf_init] ssl client info:
[1988406596] PrivateKey=
[1988406596] MyCertificate=
[1988406596] CaCertificate=
[1988406596] SSL_method=33
[1988406596] verify_mode=1
[1988406596] cipher_suites=ADH:SHA1:HIGH:EXP
[1988406596] tftp_server_ip=140.92.61.131
[1988406596] fn_myCerttificate=ServCert.pem
[1988406596] fn_privateKey=PrivKey.pem
[1988406596] fn_caCertificate=CaCert.pem
[1988406596] sslc_conf_init> ssl client info end:
[1988406596] [sslc_conf_init] pCtx=0x55331920 in ssld_conf_init
[1988406596][sslc_conf_init]SSL client failed setting TLS version to 1.3
[1988406596][sslc_conf_init]SSL client failed setting TLS version to 1.3
[1988406596] [sslc_ctx_reset_cert] re-LoadCACertificate( 3rdCA ) ok!!
[1988406596] [sslc_ctx_reset_cert] re-LoadCACertificate( 2ndCA ) ok!!
[1988406596] [sslc_ctx_reset_cert] re-LoadCACertificate( 1stCA ) ok!!Load CA Arcadyan.crt ok!
Load CA Comodo.crt ok!
Load CA Comodo_TA.crt ok!
Load CA Comodo_TA2.crt ok!
Load CA Telstra2.crt ok!
Load CA Telstra_CA.crt ok!
Load CA Telstra_CA_Chain.crt ok!
Load CA Telstra_Root_CA.crt ok!
Load CA globalsign.crt ok!
[sslc_ctx_reset_cert] this is pkcs12 type certificate
LoadServerCertAndKeyFromPKCS12Format> MAC verified OK
LoadServerCertAndKeyFromPKCS12Format> PKCS12_parse() return pkey=0x55349810, x509=0x5533abf0
data=30:82:4:a4
data=38:6b:61:4c
LoadServerCertAndKeyFromPKCS12Format> out_len=1856
[1988406596] sslc_ctx_reset_cert : re-LoadServerCertAndKey() ok!!
[1988406596] [sslc_conf_init] sslc_conf_init() ok
[Init_SSLClient] g_Client_Cert_Array[0]=0x76f51c50
[ 67.694936] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 67.727931] option 4-1:1.0: GSM modem (1-port) converter detected
[ 67.728160] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 67.733611] option 4-1:1.1: GSM modem (1-port) converter detected
[ 67.740726] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 67.746498] option 4-1:1.2: GSM modem (1-port) converter detected
[ 67.753193] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 67.759383] option 4-1:1.3: GSM modem (1-port) converter detected
[ 67.766199] usb 4-1: GSM modem (1-port) converter now attached to ttyUSB3
[ 67.791404] qmi_wwan_q 4-1:1.4: cdc-wdm0: USB WDM device
[ 67.791610] qmi_wwan_q 4-1:1.4: Quectel RG500Q-EA work on RawIP mode
[ 67.796341] qmi_wwan_q 4-1:1.4: rx_urb_size = 31744
[ 67.803651] qmi_wwan_q 4-1:1.4 rmnet_usb0: register 'qmi_wwan_q' at usb-xhci-hcd.1.auto-1, RMNET/USB device, 0a:b8:8b:e8:2d:7c
[ 67.805387] 8021q: VLANs not supported on rmnet_usb0
[ 67.825969] net rmnet_usb0: qmap_register_device(rmnet_usb0.1)=0
[ 67.826315] net rmnet_usb0 rmnet_usb0.1: NSS context created
[ 67.828093] 8021q: VLANs not supported on rmnet_usb0
[ 67.829781] 8021q: VLANs not supported on rmnet_usb0
[ 67.830145] 8021q: VLANs not supported on rmnet_usb0
[ 67.846720] net rmnet_usb0: qmap_register_device rmnet_usb0.1
[ 67.852654] net rmnet_usb0: qmap_register_device(rmnet_usb0.2)=0
[ 67.857583] net rmnet_usb0 rmnet_usb0.2: NSS context created
[ 67.863313] net rmnet_usb0: qmap_register_device rmnet_usb0.2
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.0/ttyUSB0/..]
Ignore duplicate root dev...
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.0/ttyUSB0/tty/ttyUSB0/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.0/ttyUSB0/tty/ttyUSB0]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[4-1-00]:[00/00/00]:2c7c:0800:5
[BaseClass]:[PCIDEV]=[00]:[]
/sbin/hotplug-call: 2c7c\:0800\:5\: interfacce 00/00/00.!
/sbin/hotplug-call: Unsupport 2c7c\:0800\:5 !
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.1/ttyUSB1/..]
Ignore duplicate root dev...
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.1/ttyUSB1/tty/ttyUSB1/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.1/ttyUSB1/tty/ttyUSB1]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[4-1-01]:[00/00/00]:2c7c:0800:5
[BaseClass]:[PCIDEV]=[00]:[]
/sbin/hotplug-call: 2c7c\:0800\:5\: interfacce 00/00/00.!
/sbin/hotplug-call: interfacce 00/00/00.! not Supported.!
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.2/ttyUSB2/..]
Ignore duplicate root dev...
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.2/ttyUSB2/tty/ttyUSB2/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.2/ttyUSB2/tty/ttyUSB2]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[4-1-02]:[00/00/00]:2c7c:0800:5
[BaseClass]:[PCIDEV]=[00]:[]
/sbin/hotplug-call: 2c7c\:0800\:5\: interfacce 00/00/00.!
/sbin/hotplug-call: Unsupport 2c7c\:0800\:5\: !
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.3/ttyUSB3/..]
Ignore duplicate root dev...
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.3/ttyUSB3/tty/ttyUSB3/../../..]
/sbin/hotplug-call: [DEVPATH]=[/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.3/ttyUSB3/tty/ttyUSB3]
/sbin/hotplug-call: [HOST-PORT-IFA]:[INTERFACE]:VID:PID:IFN=[4-1-03]:[00/00/00]:2c7c:0800:5
[BaseClass]:[PCIDEV]=[00]:[]
/sbin/hotplug-call: 2c7c\:0800\:5\: interfacce 00/00/00.!
/sbin/hotplug-call: interfacce 00/00/00.! not Supported.!
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.4/net/rmnet_usb0/../../..]
INTERFACE=[rmnet_usb0]
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.4/net/rmnet_usb0/net/rmnet_usb0.1/../../../..]
INTERFACE=[rmnet_usb0.1]
SPATH=[/sys/devices/platform/soc/8cf8800.usb3/8c00000.dwc3/xhci-hcd.1.auto/usb4/4-1/4-1:1.4/net/rmnet_usb0/net/rmnet_usb0.2/../../../..]
INTERFACE=[rmnet_usb0.2]
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need space = 211699
/sbin/hotplug-call: Quectel RG500Q (rmnet_usb0)
[interface_usb] INTERFACE:rmnet_usb0, 1:dhcp
[ifup] mode:, ignore_reload:0
[ 70.542634] IPv6: ADDRCONF(NETDEV_UP): rmnet_usb0: link is not ready
[ 70.542689] 8021q: VLANs not supported on rmnet_usb0
[ 70.550099] 8021q: VLANs not supported on rmnet_usb0
[ 70.554774] IPv6: ADDRCONF(NETDEV_UP): rmnet_usb0.1: link is not ready
/sbin/hotplug-call: HOST/PORT/VID/PID/IFN=4/1/2C7C/0800/5
[arca.dbus.ltecommander received: ["arca.dbus.ltecommander:CMD_ADD 4 1 2C7C 0800 5"]]
command_handler:601: lte agent command_handler: argc = 6
command_handler:604: lte agent command_handler: COMMAND:[CMD_ADD]
sendSignalShm2Ltecommander:373: argc:6, cmd:0
sendSignalShm2Ltecommander:375: argv[0]:CMD_ADD
sendSignalShm2Ltecommander:377: argv[1]:4
sendSignalShm2Ltecommander:379: argv[2]:1
sendSignalShm2Ltecommander:381: argv[3]:2C7C
sendSignalShm2Ltecommander:382: argv[4]:0800
sendSignalShm2Ltecommander:576: sending SIGUSR1 signal with sival_int 0 to pid 5940......
[ 71.692298] (5940) <INF> Add(host/port/vid/pid/ifnum): 4/1/0x2c7c/0x0800/5
/sbin/hotplug-call: Hotplug done (rmnet_usb0)
[ 71.695982] (5940) <INF> gui_update_device_status() dev_status:Unknown
[ 71.698651] (5940) <INF> sm_function_set() Function:1
[ 71.698701] (5940) <INF> Handled event (INIT)
[ 71.698761] (5940) <INF> gui_clear_device_status() dev_status:Unknown
[ 71.700359] (5940) <INF> Supported device found, use_scan:0: 2c7c:0800 RG500Q
[ 71.700479] (5940) <INF> GetInitModuleCfgFromGui() Dflt upg_st_dly:5
[ 71.700557] (5940) <INF> GetInitModuleCfgFromGui() Dflt upg_ed_dly:0
[ 71.700632] (5940) <INF> GetInitModuleCfgFromGui() Dflt st_dly:5
[ 71.700704] (5940) <INF> GetInitModuleCfgFromGui() Dflt at_dly:0
[ 71.700778] (5940) <INF> GetInitModuleCfgFromGui() Dflt pin_dly:3
[ 71.700850] (5940) <INF> GetInitModuleCfgFromGui() Dflt voice_rx_gain:50000
[ 71.701246] (5940) <INF> gui_update_device_status() dev_status:Identified
[ 71.701328] (5940) <INF> scan_device() trying remove emergency boot
[ 71.701367] (5940) <INF> scan_device() remove emergency boot OK:1
[ 71.701402] (5940) <INF> scan_device() trying remove manual power reboot
[ 71.701446] (5940) <INF> scan_device() needn't remove manual power reboot
[ 71.701546] (5940) <INF> dflt_qmi_test_upg_init_chk() vid/pid/ifnum: 0x2c7c/0x0800/5
[ 71.701589] (5940) <INF> dflt_qmi_test_upg_init_chk() Normal mode !
[ 71.701630] (5940) <INF> set_module_em_boot() emergency boot OFF !
[ 71.706623] (5940) <WRN> lte_gpio_out_ctrl():45 set gpio-16:0 completed !!
[ 71.706696] (5940) <INF> set_module_em_boot() emergency boot OFF for R0A platform, OK !
[ 71.706773] (5940) <INF> Resetting LTE Commander, type: 2
[ 71.706808] (5940) <WRN> ForcePollStop():415 Force polling task to stop
[ 71.706846] (5940) <INF> State machine 0x76f80d90 (LTE_MAIN): RESET
[ 71.706924] (5940) <INF> Unset: AT recver unavailable
[ 71.706957] (5940) <INF> Unset: AT sender unavailable
[ 71.707288] (5940) <INF> gui_clear_voice_status() voice_status:Unknown
[ 71.707373] (5940) <INF> Update SIM state ...
[ 71.707421] (5940) <INF> Update SIM state ... NO EFFECT: 0 (Unknown)
[ 71.707460] (5940) <INF> Switch network function ...
[ 71.707493] (5940) <INF> Switch network function ... NO EFFECT: 0 (Unknown)
[ 71.710782] (5940) <INF> gui_update_device_status() dev_status:Initializing
[ 71.710930] (5940) <INF> Get PDP context from GUI ...
[ 71.711101] (5940) <INF> GUI >> Data APN >> ""
[ 71.711140] (5940) <INF> GUI >> Phy PDP-ID >> "1"(1)
[ 71.711175] (5940) <INF> GUI >> IP type >> "1"(1)
[ 71.711210] (5940) <INF> GUI << Set Dflt APN << ""
[ 71.711402] (5940) <INF> GUI >> Voice APN >> "ims"
[ 71.711440] (5940) <INF> GUI >> Phy PDP-ID >> "2"(2)
[ 71.711474] (5940) <INF> GUI >> IP type >> "3"(3)
[ 71.711617] (5940) <INF> GUI >> Data Auth mode >> "0"
[ 71.711655] (5940) <INF> GUI >> Auth username >> ""
[ 71.711689] (5940) <INF> GUI >> Auth password >> ""
[ 71.711828] (5940) <INF> GUI >> Voice Auth mode >> "0"
[ 71.711892] (5940) <INF> GUI >> Auth username >> ""
[ 72.045812] (5940) <INF> GUI >> Auth password >> ""
[ 72.046067] (5940) <INF> GUI >> Data PDP >> 1,"IP",""
[ 72.046107] (5940) <INF> GUI >> Data Auth >> auth_type:[None/0], user:[], pass:[]
[ 72.046180] (5940) <INF> GUI >> Data Auth >> ip_type:[IP/1], apn:[]
[ 72.046222] (5940) <INF> GUI >> Voice PDP >> 2,"IPV4V6","ims"
[ 72.046257] (5940) <INF> GUI >> Voice Auth >> auth_type:[None/0], user:[], pass:[]
[ 72.046298] (5940) <INF> GUI >> Voice Auth >> ip_type:[IPV4V6/3], apn:[ims]
[ 72.046337] (5940) <INF> Get PDP context from GUI ... OK
[ 72.046370] (5940) <INF> init_start() trying remove FW-UPG retry timer
[ 72.046411] (5940) <INF> init_start() needn't remove FW-UPG retry timer
[ 72.046671] (5940) <INF> xci3544z_module_init() Module init OK ...
[ 72.046708] (5940) <INF> init_start() Need boot-up delay 5 secs...
[ 77.046812] (5940) <INF> init_start() Need boot-up delay 5 secs, OK!
[ 77.046929] (5940) <INF> INIT AT channels ...
[ 77.047045] (5940) <INF> open_serial_port() port:[/dev/ttyUSB2]
[ 77.047474] (5940) <INF> open_serial_port() port:[/dev/ttyUSB2]
[ 81.741695] (5940) <INF> open_serial_port() port:[/dev/ttyUSB3]
[ 82.243692] (5940) <INF> close_serial_port() fd:12
[ 82.243779] (5940) <INF> open_serial_port() port:[/dev/ttyUSB3]
[ 82.746226] (5940) <INF> close_serial_port() fd:12
[ 82.746328] (5940) <INF> open_serial_port() port:[/dev/ttyUSB3]
[ 83.263962] (5940) <INF> close_serial_port() fd:12
[ 83.264071] (5940) <INF> open_serial_port() port:[/dev/ttyUSB3]
[ 83.766233] (5940) <INF> close_serial_port() fd:12
[ 83.766323] (5940) <INF> at_io_setup() TTY2 init ready...
[ 83.766356] (5940) <INF> INIT AT channels ... OK
[ 83.766388] (5940) <INF> Switch network function ...
[ 83.766422] (5940) <INF> Switch device network function ...
[ 83.766456] (5940) <INF> DEV << network function << 0 (Flight mode)
[ 83.768384] (5940) <INF> DEV >> OK
[ 84.768486] (5940) <INF> Switch device network function ... OK
[ 84.768589] (5940) <INF> VAR << network function << 0 (Unknown) -> 2 (Flight mode)
[ 84.768633] (5940) <INF> ForcePollPause() poll_pause:1
[ 84.768790] (5940) <INF> VAR << network state << 0 (Unknown) -> 1 (NotPresent)
[ 84.768868] (5940) <INF> dnsv6: (null)
[ 84.769181] (5940) <INF> GUI-APN << [Data PDP1-1:rmnet_usb0.1] << "NotPresent"
[ 84.769401] (5940) <INF> VAR << network state << 1 (NotPresent) -> 3 (Dormant)
[ 84.769472] (5940) <INF> dnsv6: (null)
[ 84.769711] (5940) <INF> GUI-APN << [Data PDP1-1:rmnet_usb0.1] << "Dormant"
[ 84.769757] (5940) <INF> Update network state ... OK
[ 84.769847] (5940) <INF> VAR << network state << 0 (Unknown) -> 3 (Dormant)
[ 84.769890] (5940) <INF> SYS << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2]
[ 84.769989] (5940) <INF> GUI-APN << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2] << Dormant
[ 84.770060] (5940) <INF> Update network state ... OK
[ 84.772499] (5940) <INF> Update network state ... OK
[ 84.772591] (5940) <INF> VAR << network state << 3 (Dormant) -> 1 (NotPresent)
[ 84.772661] (5940) <INF> SYS << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2]
[ 84.772772] (5940) <INF> GUI-APN << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2] << NotPresent
[ 84.772910] (5940) <INF> Update network state [Data PDP1-1:rmnet_usb0.1], NO EFFECT: 3 (Dormant)
[ 84.773014] (5940) <INF> VAR << network state << 1 (NotPresent) -> 3 (Dormant)
[ 84.773057] (5940) <INF> SYS << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2]
[ 84.773165] (5940) <INF> GUI-APN << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2] << Dormant
[ 84.773221] (5940) <INF> Update network state ... OK
[ 84.776182] (5940) <INF> Update network state ... OK
[ 84.776217] (5940) <INF> Switch network function ... OK
[ 84.776265] (5940) <WRN> event_q_handler():543 device initializing, skip check
[ 84.777631] (5940) <INF> act_get_imei() IMEI:[869119050193836]
[ 84.778572] (5940) <INF> act_get_imei() IMEISV:0x1e/30
[ 84.778611] (5940) <INF> RG500Q << Get FW version
[ 84.779514] (5940) <INF> quectel_rg50_fw_sver() ver_i:[RG500QEAAAR11A03M4G_ACY]
[ 84.779551] (5940) <INF> quectel_rg50_fw_sver() ver_i_sub:[M4G_ACY], prefix:[RG500QEAAA]/1
[ 84.779646] (5940) <INF> quectel_rg50_fw_sver() new ACY version
[ 84.779677] (5940) <INF> quectel_rg50_fw_sver() new ACY version, set default:[1.1.1.1]
[ 84.779755] (5940) <INF> quectel_rg50_fw_std_hw_ver() IMEI:[869119050193836], val:193836
[ 84.779795] (5940) <INF> quectel_rg50_fw_std_hw_ver(0) ES2.1 HW + >= R01A02 FW
[ 84.779826] (5940) <INF> quectel_rg50_fw_std_hw_ver() new hw ver, prefix:[RG500QEAAA], ver:9
[ 84.779863] (5940) <INF> quectel_fw_ver() new FW ver:[RG500QEAAAR11A03M4G_ACY] support OPCO list check...
[ 84.779899] (5940) <INF> quectel_read_fw_version() curren ver:11.3.1.1.1.1(HW:9,Dflt:0,Std:1)
[ 84.779944] (5940) <INF> quectel_read_fw_version() target ver:1.1.5.24.0.0(HW:0,Dflt:0)
[ 84.779988] (5940) <INF> RG500Q >> RG500QEAAAR11A03M4G_ACY
[ 84.781818] (5940) <INF> get_device_version() Private ver0:[RG500QEA_VH_V00003_202010291/0], ver1:[V03/3]
[ 84.785571] (5940) <INF> gui_update_checklist() config cAPNs:[telstra.hybrid,internet]
[ 84.785651] (5940) <INF> gui_update_checklist() cAPNs num_token:2
[ 84.785688] (5940) <INF> gui_update_checklist() cAPNs token-0:[telstra.hybrid]
[ 84.785725] (5940) <INF> gui_update_checklist() cAPNs token-1:[internet]
[ 84.785807] (5940) <INF> gui_update_checklist() config cPLMNs:[00101,00606,50501,466*]
[ 84.785853] (5940) <INF> gui_update_checklist() cPLMNs num_token:4
[ 84.785889] (5940) <INF> gui_update_checklist() cPLMNs token-0:[00101]
[ 85.120736] (5940) <INF> gui_update_checklist() cPLMNs token-1:[00606]
[ 85.120776] (5940) <INF> gui_update_checklist() cPLMNs token-2:[50501]
[ 85.120812] (5940) <INF> gui_update_checklist() cPLMNs token-3:[466*]
[ 85.120848] (5940) <INF> gui_update_checklist() cPLMNs-0:[1/1]
[ 85.120884] (5940) <INF> gui_update_checklist() cPLMNs-1:[6/6]
[ 85.120919] (5940) <INF> gui_update_checklist() cPLMNs-2:[505/1]
[ 85.120954] (5940) <INF> gui_update_checklist() cPLMNs-3:[466/-1]
[ 85.121011] (5940) <WRN> event_q_handler():543 device initializing, skip check
[ 85.121071] (5940) <INF> SIM check ...
[ 85.121102] (5940) <INF> Update SIM state from device ...
[ 85.121135] (5940) <INF> Get SIM state ...
[ 85.122088] (5940) <INF> DEV >> SIM state >> 1 (Valid)
[ 85.122129] (5940) <INF> Update SIM state ...
[ 85.122162] (5940) <INF> VAR << SIM state << 0 (Unknown) -> 1 (Valid)
[ 85.122311] (5940) <INF> GUI << SIM state << "Valid"
[ 85.125940] (5940) <INF> Update SIM facility lock state from device ...
[ 85.126007] (5940) <INF> Get SIM facility lock state ...
[ 85.127164] (5940) <INF> DEV >> SIM facility lock state >> 0
[ 85.127202] (5940) <INF> Update SIM facility lock state from device ... NO EFFECT: 0
[ 85.127239] (5940) <INF> Update SIM lock counter from device ...
[ 85.127273] (5940) <INF> Get SIM lock counter ...
[ 85.128369] (5940) <INF> DEV >> SIM PIN counter >> 3
[ 85.128406] (5940) <INF> DEV >> SIM PUK counter >> 10
[ 85.128439] (5940) <INF> Update SIM lock counter ...
[ 85.128472] (5940) <INF> VAR << SIM PIN counter << 0 -> 3
[ 85.128507] (5940) <INF> VAR << SIM PUK counter << 0 -> 10
[ 85.128696] (5940) <INF> GUI << SIM PIN counter << 3
[ 85.128731] (5940) <INF> GUI << SIM PUK counter << 10
[ 85.128764] (5940) <INF> Update SIM lock counter ... OK
[ 85.128811] (5940) <INF> Update SIM lock counter from device ... OK
[ 85.128845] (5940) <INF> Update SIM identity from device ...
[ 85.128879] (5940) <INF> Get SIM identity ...
[ 85.131594] (5940) <INF> DEV >> SIM ICCID >> "89610180003772912529"
[ 85.131630] (5940) <INF> DEV >> SIM IMSI >> "505013700200942"
[ 85.131663] (5940) <INF> DEV >> SIM MSISDN >> ""
[ 85.131697] (5940) <INF> Update SIM identity ...
[ 85.131730] (5940) <INF> VAR << SIM ICCID << "" -> "89610180003772912529"
[ 85.131773] (5940) <INF> VAR << SIM IMSI << "" -> "505013700200942"
[ 85.131808] (5940) <INF> VAR << SIM MSISDN << "" -> ""
[ 85.131990] (5940) <INF> Update SIM identity ... OK
[ 85.132024] (5940) <INF> Update SIM identity from device ... OK
[ 85.136654] (5940) <INF> Update SIM state ... OK
[ 85.136698] (5940) <INF> Update SIM state from device ... OK
[ 85.136749] (5940) <INF> Handled URC (QIND): +QIND: SMS DONE
[ 85.136871] (5940) <INF> SIM check ... OK
[ 85.136914] (5940) <INF> Handled URC (QIND): +QIND: PB DONE
[ 85.136968] (5940) <INF> vinit_hw_param_start() check FW version ok
[ 85.139551] (5940) <INF> check_sim_swap_config() check SIM swap ok
[ 85.140405] (5940) <INF> vinit_hw_param_start() Default CFUN config:, 0
[ 85.142082] (5940) <INF> vinit_hw_dflt_val() check dflt CFUN-conf:0 ok
[ 85.144395] (5940) <INF> Current param:[9 0 1 0 4 0 1 2 1 2 0 0]
[ 85.144447] (5940) <INF> Target param:[9 127 1 0 4 0 1 2 1 2 0 0]
[ 85.476297] (5940) <INF> vinit_hw_dflt_val() check PCM codec ok
[ 85.476335] (5940) <INF> quectel_at_test_priv_param() bypass thermal check
[ 85.476368] (5940) <INF> quectel_at_test_priv_param() bypass 256QAM check
[ 85.476399] (5940) <INF> quectel_at_test_priv_param() bypass LAPI check
[ 85.476541] (5940) <INF> quectel_at_test_priv_param() bootargs unchange [RG50], bypass data_interface check
[ 85.476585] (5940) <INF> quectel_at_test_priv_param() bypass ring delay check
[ 85.476616] (5940) <INF> quectel_at_test_priv_param() bypass dflt session timer check
[ 85.477681] (5940) <WRN> quectel_at_read_ims_dflt():3362 FAIL, ret:7, num_rsp:1
[ 85.477721] (5940) <WRN> vinit_hw_dflt_val():316 get IMS dflt FAILED
[ 85.478671] (5940) <INF> quectel_at_read_fax_codec() ret:7, num_rsp:1, dflt_g711:0
[ 85.478713] (5940) <INF> vinit_hw_dflt_val() check FAX codec ok
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 8, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 9, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 10, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 11, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 12, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 13, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 14, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 15, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 16, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 17, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 18, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 19, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 20, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
ERROR: Config Index Out of Range! cfgID: ARC_USB_DONGLE_x_VoLTE_Profile, Index1 = 21, Index1 Limit = 8, Index2 = -2147483648, Index2 Limit = 0
[ 85.783460] (5940) <INF> vinit_hw_opco_profile() conf empty, use default value:[Telstra_Australia_Commercial]
[ 85.783535] (5940) <INF> vinit_hw_opco_profile() sscanf:1, profile/date:[Telstra_Australia_Commercial/], conf_idx:0
[ System Startup s], Cnt:22, Sel:0, Conf:0, Auto:1 ========================
VoLTE Status: Unknown
Codec : 9,0,1,0,4,0,1,2,1,2,0,0
-----------------------------------------------------------------------------
idx id Cfg Sta Name Version Private
--- -- --- --- ------------------------------------------ --------- ---------
0 0 0 1 Telstra_Australia_Commercial 202007081 0A010F00h
1 1 0 0 ROW_Commercial 202001061 0A010809h
2 2 0 0 Volte_OpenMkt-Commercial-CMCC 202001061 0A012010h
3 3 0 0 ChunghwaTel_Taiwan_Commercial 202006011 0A014F00h
4 4 0 0 Spark_Commercial 202007081 0A01FE09h
5 5 0 0 Telia_Sweden 201908071 0A012400h
6 6 0 0 TIM_Italy_Commercial 201908071 0A012B00h
7 7 0 0 France-Commercial-Orange 201908071 0A010B21h
8 8 0 0 Commercial-DT-VOLTE 201908071 0A011F1Fh
9 9 0 0 Germany-VoLTE-Vodafone 201908071 0A010449h
10 10 0 0 UK-VoLTE-Vodafone 201908071 0A010426h
11 11 0 0 Commercial-EE 201908071 0A01220Bh
12 12 0 0 Optus_Australia_Commercial 201908071 0A014400h
13 13 0 0 Commercial-LGU 201908071 0A012608h
14 14 0 0 Commercial-KT 201908071 0A01280Bh
15 15 0 0 Commercial-SKT 201908071 0A01270Ah
16 16 0 0 Commercial-Reliance 202006011 0A011B0Ch
17 17 0 0 Commercial-SBM 201908071 0A011C0Bh
18 18 0 0 Commercial-KDDI 201908071 0A010709h
19 19 0 0 Commercial-DCM 201908071 0A010D0Dh
20 20 0 0 VoLTE-CU 202001061 0A011561h
21 21 0 0 VoLTE_OPNMKT_CT 202001061 0A0113E0h
==============================================================================
[ 85.784287] (5940) <INF> vinit_hw_opco_profile() haveSIM:1
[ 85.784322] (5940) <INF> vinit_hw_opco_profile() profile config match:0(Telstra_Australia_Commercial)
[ 85.784392] (5940) <INF> vinit_hw_param_done() check VoLTE HW, voice_status:Unknown
[ 85.784430] (5940) <INF> gui_update_voice_status() voice_status:Unknown
[ 86.115631] (5940) <INF> vinit_hw_param_done() VoLTE HW check OK
[ 86.115734] (5940) <WRN> fw_upg_complete_chk():780 Needn't reboot device !!!
[ 86.115941] (5940) <INF> prefer_network_select() prefer network default:3,4,100,0, cnt:2
[ 86.115996] (5940) <INF> prefer_network_select() prefer network config:3,4,100,0, cnt:2
[ 86.117124] (5940) <INF> quectel_at_read_prefer_network() token-2:[LTE], mode-0:3
[ 86.117165] (5940) <INF> quectel_at_read_prefer_network() token-3:[NR5G], mode-1:4
[ 86.117204] (5940) <INF> quectel_at_read_prefer_network() mode:3,4,100,0, dflt_mode:3,4,100,0, ret:0
[ 86.117253] (5940) <INF> prefer_network_select() check OK:3,4,100,0, cnt:2
[ 86.117334] (5940) <INF> prefer_domain_select() prefer domain default:PS(1)
[ 86.118297] (5940) <INF> quectel_at_read_prefer_domain() val:1, conf_val:1, ret:0
[ 86.118339] (5940) <INF> prefer_domain_select() check OK:PS(1)
[ 86.118414] (5940) <INF> prefer_nr_select() prefer NR default:NSA(1)
[ 86.119419] (5940) <INF> quectel_at_read_prefer_nr() val:1, conf_val:1, ret:0
[ 86.119460] (5940) <INF> prefer_nr_select() check OK:NSA(1)
[ 86.119496] (5940) <INF> Sync PDP context with GUI ...
[ 86.119530] (5940) <INF> Get PDP context from GUI ...
[ 86.119679] (5940) <INF> GUI >> Data APN >> ""
[ 86.119718] (5940) <INF> GUI >> Phy PDP-ID >> "1"(1)
[ 86.119754] (5940) <INF> GUI >> IP type >> "1"(1)
[ 86.119788] (5940) <INF> GUI << Set Dflt APN << ""
[ 86.119993] (5940) <INF> GUI >> Voice APN >> "ims"
[ 86.120058] (5940) <INF> GUI >> Phy PDP-ID >> "2"(2)
[ 86.120093] (5940) <INF> GUI >> IP type >> "3"(3)
[ 86.120243] (5940) <INF> GUI >> Data Auth mode >> "0"
[ 86.120281] (5940) <INF> GUI >> Auth username >> ""
[ 86.120315] (5940) <INF> GUI >> Auth password >> ""
[ 86.120460] (5940) <INF> GUI >> Voice Auth mode >> "0"
[ 86.120498] (5940) <INF> GUI >> Auth username >> ""
[ 86.120531] (5940) <INF> GUI >> Auth password >> ""
[ 86.120672] (5940) <INF> GUI >> Data PDP >> 1,"IP",""
[ 86.120710] (5940) <INF> GUI >> Data Auth >> auth_type:[None/0], user:[], pass:[]
[ 86.120752] (5940) <INF> GUI >> Data Auth >> ip_type:[IP/1], apn:[]
[ 86.120791] (5940) <INF> GUI >> Voice PDP >> 2,"IPV4V6","ims"
[ 86.120825] (5940) <INF> GUI >> Voice Auth >> auth_type:[None/0], user:[], pass:[]
[ 86.120866] (5940) <INF> GUI >> Voice Auth >> ip_type:[IPV4V6/3], apn:[ims]
[ 86.120904] (5940) <INF> Get PDP context from GUI ... OK
[ 86.120936] (5940) <INF> Get PDP context from device ...
[ 86.123904] (5940) <INF> DEV >> [Data PDP1-1:rmnet_usb0.1] >> APN:1,"IP","telstra.hwa","0.0.0.0",0,0,0,0,,,,,,,,,"",,,,0
[ 86.123953] (5940) <INF> DEV >> [Voice PDP2-2:rmnet_usb0.2] >> APN:2,"IPV4V6","ims","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0,,,,,,,,,"",,,,0
[ 86.125905] (5940) <INF> DEV >> [Data PDP1-1:rmnet_usb0.1] >> AUTH auth_type:[None/0], username:[], password:[]
[ 86.125958] (5940) <INF> DEV >> [Data PDP1-1:rmnet_usb0.1] >> AUTH ip_type:[IP/1], apn:[telstra.hwa]
[ 86.126005] (5940) <INF> DEV >> [Voice PDP2-2:rmnet_usb0.2] >> AUTH auth_type:[None/0], username:[], password:[]
[ 86.454434] (5940) <INF> DEV >> [Voice PDP2-2:rmnet_usb0.2] >> AUTH ip_type:[IPV4V6/3], apn:[ims]
[ 86.454490] (5940) <INF> Get PDP context from device ... OK
[ 86.454527] (5940) <INF> Sync PDP context ...
[ 86.481494] (5940) <INF> Sync PDP context ... SYNCED [Data PDP1-1:rmnet_usb0.1]
[ 86.481568] (5940) <INF> Sync PDP context ... SYNCED 1 items
[ 86.481605] (5940) <INF> Sync PDP context with GUI ... OK
[ 86.481641] (5940) <INF> reattach_network() [Data PDP1-1:rmnet_usb0.1] changed. Re-attach to take effect ...
[ 86.481705] (5940) <INF> reattach_network() [Voice PDP2-2:rmnet_usb0.2] changed. Re-attach to take effect ...
[ 86.481750] (5940) <INF> Switch network function ...
[ 86.481784] (5940) <INF> Switch network function ... NO EFFECT: 2 (Flight mode)
[ 86.481821] (5940) <INF> Switch network function ...
[ 86.481852] (5940) <INF> Switch device network function ...
[ 86.481885] (5940) <INF> DEV << network function << 2 (Full mode)
[ 86.483983] (5940) <INF> DEV >> OK
[ 87.484083] (5940) <INF> Switch device network function ... OK
[ 87.484186] (5940) <INF> VAR << network function << 2 (Flight mode) -> 3 (Full mode)
[ 87.484228] (5940) <INF> ForcePollResume() isClear:1, poll_pause:0
[ 87.484381] (5940) <INF> VAR << network state << 3 (Dormant) -> 2 (Attaching)
[ 87.484429] (5940) <INF> dnsv6: (null)
[ 87.484696] (5940) <INF> GUI-APN << [Data PDP1-1:rmnet_usb0.1] << "Attaching"
[ 87.510038] (5940) <INF> Update network state ... OK
[ 87.510178] (5940) <INF> VAR << network state << 3 (Dormant) -> 2 (Attaching)
[ 87.510224] (5940) <INF> SYS << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2]
[ 87.510330] (5940) <INF> GUI-APN << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2] << Attaching
[ 87.510377] (5940) <INF> Update network state ... OK
[ 87.510411] (5940) <INF> Switch network function ... OK
[ 87.510458] (5940) <INF> Handled URC (QIND): +QIND: SMS DONE
[ 87.511786] (5940) <INF> init_sms() SMS type check OK
[ 87.512539] (5940) <INF> init_sms() SMS URC check OK
[ 87.513588] (5940) <INF> init_sms() SMS storage check OK
[ 87.514311] (5940) <INF> init_sms() SMS format check OK
[ 87.515592] (5940) <INF> init_sms() SMS codepage set OK
[ 87.516892] (5940) <INF> init_sms() SMS header set OK
[ 87.516964] (5940) <INF> init_pb() PhoneBook config disabled...
[ 87.517036] (5940) <INF> gui_update_device_status() dev_status:Initialized
[ 87.517184] (5940) <INF> init_done() Multi-WAN, wait for AWS trigger connect
[ 87.519947] (5940) <WRN> at_time_read_pfx_str1():230 AT read failed for [AT+QRXGAIN?], ret: 7
[ 87.519998] (5940) <WRN> quectel_at_set_voice_param():1593 read DSCI fail ret:7, (null)
[ 87.520080] (5940) <INF> quectel_at_set_voice_param() Rx Gain module:0, dflt-conf:50000
[ 87.522069] (5940) <WRN> at_time_set():277 AT set error for [AT+QRXGAIN=50000], ret: 7
[ 87.522119] (5940) <WRN> quectel_at_set_voice_param():1602 set rx gain, fail !
[ 87.525232] (5940) <WRN> at_time_set():277 AT set error for [AT+QAUDMOD=1], ret: 7
[ 87.525287] (5940) <WRN> quectel_at_set_voice_param():1611 select ACDB file 1, fail !
[ 87.525326] (5940) <WRN> vinit_sw_param():654 FAILED
[ 87.525450] (5940) <WRN> vinit_sw_param_done():698 VoLTE SW check FAILED, Ignore following process...
[ 87.525503] (5940) <INF> gui_update_voice_status() voice_status:Error ADB/Codec Parameters
[ 87.525723] (5940) <INF> sms_check_is_ready(STATE_SMS_LIST) network attaching, wait 30 secs and retry...
[ 87.525837] (5940) <INF> Polling starting
[ 87.525889] (5940) <INF> Polling started
[ 87.546017] (5940) <INF> VAR << network state << 2 (Attaching) -> 3 (Dormant)
[ 87.546099] (5940) <INF> dnsv6: (null)
[ 87.546424] (5940) <INF> GUI-APN << [Data PDP1-1:rmnet_usb0.1] << "Dormant"
[ 87.546487] (5940) <INF> Update network state ... OK
[ 87.546588] (5940) <INF> VAR << network state << 2 (Attaching) -> 3 (Dorma[ 87.791195] net rmnet_usb0: ul_data_aggregation_max_datagrams=11, ul_data_aggregation_max_size=4096, dl_minimum_padding=0
nt)
[ 87.546632] (5940) <INF> SYS << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2]
[ 87.546752] (5940) <INF> GUI-APN << VoLTE on ignore [Voice PDP2-2:rmnet_usb0.2] << Dormant
[ 87.546798] (5940) <INF> Update network state ... OK
[ 87.551768] (5940) <INF> poll_cell_info() [Data PDP1-1:rmnet_usb0.1] IP:[22.218.15.42], ret:0
[ 87.551820] (5940) <INF> gui_update_device_status() dev_status:Ready
[mobile_monitor] module attached, start data connecting...
[arca.dbus.ltecommander received: ["arca.dbus.ltecommander:CMD_CONNECT"]]
command_handler:601: lte agent command_handler: argc = 1
command_handler:604: lte agent command_handler: COMMAND:[CMD_CONNECT]
sendSignalValue2Ltecommander:340: sending SIGUSR1 signal with sival_int 3 to pid 5940......
[ 93.874085] (5940) <INF> Connecting...0
[ 93.881617] (5940) <INF> Handled event (CONNECT)
[ 93.881681] (5940) <INF> Data entering LTE mode
[ 93.881734] (5940) <INF> data_start() Try [Data PDP1-1:rmnet_usb0.1]
[ 93.881944] (5940) <INF> Change network state:[Data PDP1-1:rmnet_usb0.1] to Up(4)... readyConnect:1, readyDisconnect:0
[ 93.881999] (5940) <INF> VAR << network IP type << 2 (IPv6 only) -> 1 (IPv4 only)
[ 93.882110] (5940) <INF> GUI-IP type << [Data PDP1-1:rmnet_usb0.1] << 1
[ 93.882154] (5940) <INF> ChangeDeviceNetState() [Data PDP1-1:rmnet_usb0.1] Always use PDP IPType:1(IP)
[ 93.882202] (5940) <INF> ForcePollPause() poll_pause:1
[ 93.882236] (5940) <INF> quectel_qmi_exec_connect() [Data PDP1-1:rmnet_usb0.1], Connect
[ 93.882283] (5940) <INF> Get auto data APN from device ...
[ 93.883951] (5940) <INF> DEV >> Auto Data APN >> telstra.hwa
[ 93.886663] (5940) <INF> DEV [Data PDP1-1:rmnet_usb0.1] << Connect << cmd:[quectel-CM -4 -n 1 -s telstra.hwa]
[ 94.340732] IPv6: ADDRCONF(NETDEV_CHANGE): rmnet_usb0.1: link becomes ready
[ 94.341385] net rmnet_usb0: link_state 0x0 -> 0x1
[ 94.341978] (5940) <INF> DEV [Data PDP1-1:rmnet_usb0.1] >> OK
[ 94.342532] (5940) <INF> Change continue network state [Data PDP1-1:rmnet_usb0.1]... OK
[ 94.342635] (5940) <INF> ForcePollResume() isClear:1, poll_pause:0
[ 94.342684] (5940) <INF> VAR << network state << 3 (Dormant) -> 4 (Up)
[ 94.342729] (5940) <INF> dnsv6: (null)
[ 94.342852] (5940) <INF> SYS << [Data PDP1-1:rmnet_usb0.1] connect << lte_wan_start_new wan_idx=0
[ 94.342905] (5940) <INF> SYS << [Data PDP1-1:rmnet_usb0.1] connect << cmd:[/usr/sbin/wwan.sh up rmnet_usb0.1 dhcp]
/usr/sbin/wwan.sh: Command:up, Dev:rmnet_usb0.1, Protocol:dhcp, IP:, Netmask:, drv_id:1, dev_id:0, inf_base:rmnet_usb0
MOBILE_WAN_TYPE:6, wan_type:6
MOBILE_INF_ID :600, inf_idx:600
/usr/sbin/wwan.sh: rmnet_usb0.1 Link-up
[wwan.sh] PDPtype = IPv4
[ifup] mode:, ignore_reload:0
[ 96.555537] 8021q: VLANs not supported on rmnet_usb0
[dhcp.script] call udhcpc.user, dns is ""
[udhcpc.user] WAN_FORMAT:wan_
[udhcpc.user] New format, wan_type:6
[udhcpc.user] print input data
\@1:deconfig, reason:deconfig, INTERFACE:wan_600, interface:rmnet_usb0.1, wan_index:6 0, ip:, subnet:, broadcast:, router:, dns:, domain:, hostname:
metric:, serverid:, lease:
[udhcpc.user] end of print input data
[udhcpc.user] deconfig......
[dhcp.script] call udhcpc.user, dns is "101.168.244.103 101.168.244.101"
[udhcpc.user] WAN_FORMAT:wan_
[udhcpc.user] New format, wan_type:6
[udhcpc.user] print input data
\@1:bound, reason:bound, INTERFACE:wan_600, interface:rmnet_usb0.1, wan_index:6 0, ip:22.218.15.42, subnet:255.255.255.252, broadcast:, router:22.218.15.41, dns:101.168.244.103 101.168.244.101, domain:, hostname:mygateway
metric:, serverid:22.218.15.41, lease:7200
[udhcpc.user] end of print input data
[udhcpc.user] bound......
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need space = 211699
/sbin/hotplug-call ifup wan_v6_600 (rmnet_usb0.1)
[arc-wan-ipv6-linkup] section:wan_v6_600, phy_ifname:rmnet_usb0.1
[arc-wan-ipv6-linkup] WAN_FORMAT:wan_
[arc-wan-ipv6-linkup] New format, wan_type:6
[arc-wan-ipv6-linkup] DefaultRouteIdx:0, wan_type:6, section_index:0
[arc-wan-ipv6-linkup] section_index:0, DefaultRouteIdx:0, DefaultRouteMatch:1, start
[arc-wan-ipv6-linkup] ddns re-start...
[ntpclient-agent] start
Call SyncDevice.Func()
Call SyncDevice.DHCPv4.Client.Func()
Call SyncDevice.IP.Func()
Call SyncDevice.IP.Interface.Func()
[arc-wan-ipv6-linkup] wan_ipv6:, upload_rate:
[arc-wan-ipv6-linkup] end
Call SyncDevice.Ethernet.Link.Func()
Tr69 service start!
[ddns_stop] killall inadyn
ntpclient-agent: cmd=(ntpclient -6 -d -s -h "chronos.ntp.telstra.net chronos1.ntp.telstra.net 0.au.pool.ntp.org 1.au.pool.ntp.org 2.au.pool.ntp.org " -i 1) > /dev/null; echo $?
[ddns_start] DDNS config has error, Bye!
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
[iptablesrules-agent] fw3 is not running, add rules
ntpclient-agent: ntpclient_ret=0
now time zone is:[AEST-10AEDT,M10.1.0,M4.1.0/3]
NTP found!
Host = AW1000.arcadyan.cwmp.bdms.telstra.net, Port = 80
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need space = 211699
res->ai_family = 2
res->ai_socktype = 1
res->ai_protocol = 6
res->ai_addrlen = 16
res->ai_addr = 58.162.32.33
res->ai_family = 10
res->ai_socktype = 1
res->ai_protocol = 6
res->ai_addrlen = 28
res->ai_addr = 2001:8006:3100:2100::1
ACSOverIPvX = 10
Not found IPv6 address.
/sbin/hotplug-call ifup wan_600 (rmnet_usb0.1)
[arc-wan-linkup] section:wan_600, phy_ifname:rmnet_usb0.1
[arc-wan-linkup] WAN_FORMAT:wan_
[arc-wan-linkup] New format, wan_type:6
[arc-wan-linkup] DefaultRouteIdx:0, wan_type:6, section_index:0
[arc-wan-linkup] section_index:0, DefaultRouteIdx:0, DefaultRouteMatch:1, start
[arc-wan-linkup] ntpclient-agent start
[arc-wan-linkup] ddns re-start...
[arc-wan-linkup] pppoe-relay start...
[ntpclient-agent] start
[ddns_stop] killall inadyn
[arc-wan-linkup] killall -SIGUSR2 arc_botnet_protection...
ntpclient-agent: cmd=(ntpclient -6 -d -s -h "chronos.ntp.telstra.net chronos1.ntp.telstra.net 0.au.pool.ntp.org 1.au.pool.ntp.org 2.au.pool.ntp.org " -i 1) > /dev/null; echo $?
[arc-wan-linkup] Update QoS rules...
[ddns_start] DDNS config has error, Bye!
Not found IPv6 address.
Call SyncDevice.DHCPv4.Client.Func()
Call SyncDevice.IP.Func()
Call SyncDevice.IP.Interface.Func()
Call SyncDevice.Ethernet.Link.Func()
Tr69 service start!
ntpclient-agent: ntpclient_ret=0
now time zone is:[AEST-10AEDT,M10.1.0,M4.1.0/3]
NTP found!
[arc-wan-linkup] wan_ipv4:22.218.15.42, upload_rate:
[siteblock_updatelist] Hotplug for interface rmnet_usb0.1
[siteblock_updatelist] DEVICE:0:3 rmn
[siteblock_updatelist] WAN_IPADDRESS:0:5 22.21
[siteblock_updatelist] Execute /usr/sbin/arc_site_blocking_updatelist.sh ...
/usr/sbin/action/arc-wan-linkup: line 225: /usr/sbin/arc_site_blocking_updatelist.sh: not found
[ 111.630593] (5940) <INF> SYS >> [Data PDP1-1:rmnet_usb0.1] entered LTE mode
[ 111.630879] (5940) <INF> GUI-APN << [Data PDP1-1:rmnet_usb0.1] << "Up"
[ 111.630929] (5940) <INF> Update network state ... OK
[ 111.630956] (5940) <INF> data_start() prepare next pdp_id:3, phy_pdp_id:0
[arc-wan-linkup] route-agent CMD_EDIT_START
[arc-wan-linkup] end
[route-agent] CMD_EDIT_START
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need space = 211699
Not found IPv6 address.
[ 117.007592] (5940) <WRN> dflt_at_exec_sms_list():738 FAIL, ret:0, num_rsp:1
[ 117.007797] (5940) <INF> path:[/arc-data/sms/evt] empty
[ 117.007876] (5940) <INF> path:[/arc-data/sms/del] empty
[ 117.007951] (5940) <INF> path:[/arc-data/sms/sd_n] empty
Not found IPv6 address.
[ 124.324754] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_process_cac_completion: 136: cac expired, chan 5500 cur time 4294791
[ 124.324975] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 124.324975] FD Interval should be a factor of BI.
[ 124.324975] Disabling FD
[ 124.324975]
[ 124.335277] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 124.335277] FD Interval should be a factor of BI.
[ 124.335277] Disabling FD
[ 124.335277]
[ 124.354985] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 124.354985]
[ 124.374840] wlan: [0:I:ANY] vdev[0]: Mgt Rate:6000(kbps)
[ 124.384773] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 124.384773] FD Interval should be a factor of BI.
[ 124.384773] Disabling FD
[ 124.384773]
[ 124.390134] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD Interval : 0. Valid range is 20 - 100ms.
[ 124.390134] FD Interval should be a factor of BI.
[ 124.390134] Disabling FD
[ 124.390134]
[ 124.409921] wlan: [0:I:ANY] wlan_get_des_channel: 1773: wlan_get_des_channel: dfs_region = 2
[ 124.409921]
[ 124.429779] wlan: [0:I:ANY] vdev[1]: Mgt Rate:6000(kbps)
[ 124.439599] wlan: [0:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_COMPLETED event delivered on chan freq 5500.
[ 124.439599]
[ 124.444965] wlan: [0:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_COMPLETED event delivered on chan freq 5520.
[ 124.444965]
[ 124.456156] wlan: [0:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_COMPLETED event delivered on chan freq 5540.
[ 124.456156]
[ 124.467535] wlan: [0:I:ANY] ieee80211_dfs_deliver_event: dfs CAC_COMPLETED event delivered on chan freq 5560.
[ 124.467535]
Host = AW1000.arcadyan.cwmp.bdms.telstra.net, Port = 80
res->ai_family = 2
res->ai_socktype = 1
res->ai_protocol = 6
res->ai_addrlen = 16
res->ai_addr = 58.162.32.33
res->ai_family = 10
res->ai_socktype = 1
res->ai_protocol = 6
res->ai_addrlen = 28
res->ai_addr = 2001:8006:3100:2100::1
### New WAN_IP= 22.218.15.42:51007
create_connreq_socket: listen at 22.218.15.42 port:51007
Wait 1 secs, Send Inform 1, retryCount 0, time_count=1
==>[Tr69Rpcmethod_Inform]: Send inform with event [1] happened
Call SyncDevice.DeviceInfo.Func()
CommandKey=[]
Call SyncDevice.IP.Func()
Call SyncDevice.IP.Interface.Func()
Call SyncDevice.IP.Interface.1.IPv6Address.Func()
Value = 505013700200942
Change Device.Cellular.Interface.2.USIM.IMSI = 505013700200942
Value = 505013700200942
Change Device.Cellular.Interface.1.USIM.IMSI = 505013700200942
Value = http://22.218.15.42:51007/ConnectionRequest
Change Device.ManagementServer.ConnectionRequestURL = http://22.218.15.42:51007/ConnectionRequest
Value = Telstra
Change Device.DeviceInfo.ProvisioningCode = Telstra
Call SyncDevice.Func()
Device.RootDataModelVersion need sync function.
Call SyncDevice.IP.Interface.Func()
Read session info fail.
Call SyncDevice.DeviceInfo.X_TELSTRA_DEVICEINFO.Func()
Check M mthod = 0!!
==>[Tr69Rpcmethod_Inform]: 1 BOOT
Total 13 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">767568</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:Inform>
<DeviceId>
<Manufacturer>Arcadyan</Manufacturer>
<OUI>EC6C9A</OUI>
<ProductClass>XCI35AX44Z-TA</ProductClass>
<SerialNumber>ARC2204002079</SerialNumber>
</DeviceId>
<Event SOAP-ENC:arrayType="cwmp:EventStruct[2]">
<EventStruct>
<EventCode>1 BOOT</EventCode>
<CommandKey></CommandKey>
</EventStruct>
<EventStruct>
<EventCode>4 VALUE CHANGE</EventCode>
<CommandKey></CommandKey>
</EventStruct>
</Event>
<MaxEnvelopes>1</MaxEnvelopes>
<CurrentTime>2022-03-10T09:03:50</CurrentTime>
<RetryCount>0</RetryCount>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[13]">
<ParameterValueStruct>
<Name>Device.RootDataModelVersion</Name>
<Value xsi:type="xsd:string">2.10</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Cellular.Interface.1.USIM.IMSI</Name>
<Value xsi:type="xsd:string">505013700200942</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Cellular.Interface.2.USIM.IMSI</Name>
<Value xsi:type="xsd:string">505013700200942</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.IP.Interface.2.IPv4Address.1.IPAddress</Name>
<Value xsi:type="xsd:string">22.218.15.42</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.IP.X_TELSTRA_IP.ActiveWANInterface</Name>
<Value xsi:type="xsd:string">5G</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.DeviceInfo.HardwareVersion</Name>
<Value xsi:type="xsd:string">XCI35AX44Z-TA</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.DeviceInfo.SoftwareVersion</Name>
<Value xsi:type="xsd:string">0.02.02r build05-20201204</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.DeviceInfo.ProvisioningCode</Name>
<Value xsi:type="xsd:string">Telstra</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.DeviceInfo.X_TELSTRA_DEVICEINFO.CellularHardwareVersion</Name>
<Value xsi:type="xsd:string">RG500Q</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.DeviceInfo.X_TELSTRA_DEVICEINFO.CellularSoftwareVersion</Name>
<Value xsi:type="xsd:string">RG500QEAAAR11A03M4G_ACY</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.ManagementServer.ParameterKey</Name>
<Value xsi:type="xsd:string">1</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.ManagementServer.ConnectionRequestURL</Name>
<Value xsi:type="xsd:string">http://22.218.15.42:51007/ConnectionRequest</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.ManagementServer.AliasBasedAddressing</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:Inform>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
Host IP = 58.162.32.33
ht_client_send: different IP or secure state changed, close current socket
====== [do again] ======
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 401 Unauthorized
]try to get 1034 bytes. nRemainbytes 0, ret 1
received 1034 bytes, respSize 128000
[ht_client_send]: Get status code [401]
1961: HTTP 401: ptr=[realm="cwmp@2wire-cms"], path=[/cwmp/cwmp]
1974: pAuth=[EC6C9A-ARC2204002079:IPuAKtQZVkgkJB5B]
1978: auth_str=[Basic RUM2QzlBLUFSQzIyMDQwMDIwNzk6SVB1QUt0UVpWa2drSkI1Qg==]
====== [do again] ======
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 399 bytes. nRemainbytes 0, ret 1
received 399 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 399 bytes
Tr69Rpcmethod_RemoveFromInformQ> remove 4 VALUE CHANGE
Tr69Rpcmethod_RemoveFromInformQ> remove 1 BOOT
--------------Dump packet IN--------------
cwmp:InformResponse
MaxEnvelopes = 1
++++++++++++++Dump packet IN++++++++++++++
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 621 bytes. nRemainbytes 0, ret 1
received 621 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 621 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.DeviceInfo.X_TELSTRA_DEVICEINFO.CellularSoftwareVersion
++++++++++++++Dump packet IN++++++++++++++
Total 1 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[1]">
<ParameterValueStruct>
<Name>Device.DeviceInfo.X_TELSTRA_DEVICEINFO.CellularSoftwareVersion</Name>
<Value xsi:type="xsd:string">RG500QEAAAR11A03M4G_ACY</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 586 bytes. nRemainbytes 0, ret 1
received 586 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 586 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.ManagementServer.URL
++++++++++++++Dump packet IN++++++++++++++
Total 1 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[1]">
<ParameterValueStruct>
<Name>Device.ManagementServer.URL</Name>
<Value xsi:type="xsd:string">http://AW1000.arcadyan.cwmp.bdms.telstra.net/cwmp/cwmp</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 594 bytes. nRemainbytes 0, ret 1
received 594 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 594 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.PPP.InterfaceNumberOfEntries
++++++++++++++Dump packet IN++++++++++++++
Call SyncDevice.PPP.Func()
Total 1 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[1]">
<ParameterValueStruct>
<Name>Device.PPP.InterfaceNumberOfEntries</Name>
<Value xsi:type="xsd:unsignedInt">1</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 580 bytes. nRemainbytes 0, ret 1
received 580 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 580 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.PPP.Interface.
++++++++++++++Dump packet IN++++++++++++++
Call SyncDevice.PPP.Interface.Func()
Expecting msg length 21, is larger than buffer size 20
[MIDCORE-DEBUG]: mapi_opt_trans buffer size error action:[1], data:[ARC_WAN_600_DUID_Str]
Total 49 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[49]">
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Enable</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Status</Name>
<Value xsi:type="xsd:string">LowerLayerDown</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Alias</Name>
<Value xsi:type="xsd:string">WAN</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Name</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LastChange</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LowerLayers</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCPEnable</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPv6CPEnable</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Reset</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.ConnectionStatus</Name>
<Value xsi:type="xsd:string">Unconfigured</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LastConnectionError</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.AutoDisconnectTime</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IdleDisconnectTime</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.WarnDisconnectDelay</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Username</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Password</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.EncryptionProtocol</Name>
<Value xsi:type="xsd:string">None</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.CompressionProtocol</Name>
<Value xsi:type="xsd:string">None</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.AuthenticationProtocol</Name>
<Value xsi:type="xsd:string">CHAP</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.MaxMRUSize</Name>
<Value xsi:type="xsd:unsignedInt">1500</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.CurrentMRUSize</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.ConnectionTrigger</Name>
<Value xsi:type="xsd:string">AlwaysOn</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LCPEcho</Name>
<Value xsi:type="xsd:unsignedInt">30</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LCPEchoRetry</Name>
<Value xsi:type="xsd:unsignedInt">5</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.PPPoE.SessionID</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.PPPoE.ACName</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.PPPoE.ServiceName</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.LocalIPAddress</Name>
<Value xsi:type="xsd:string">0.0.0.0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.RemoteIPAddress</Name>
<Value xsi:type="xsd:string">0.0.0.0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.DNSServers</Name>
<Value xsi:type="xsd:string">101.168.244.103,101.168.244.101</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.PassthroughEnable</Name>
<Value xsi:type="xsd:boolean">1</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.PassthroughDHCPPool</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPv6CP.LocalInterfaceIdentifier</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPv6CP.RemoteInterfaceIdentifier</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BytesSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BytesReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.PacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.PacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.ErrorsSent</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.ErrorsReceived</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.UnicastPacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.UnicastPacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.DiscardPacketsSent</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.DiscardPacketsReceived</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.MulticastPacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.MulticastPacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BroadcastPacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BroadcastPacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.UnknownProtoPacketsReceived</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 586 bytes. nRemainbytes 0, ret 1
received 586 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 586 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.ManagementServer.URL
++++++++++++++Dump packet IN++++++++++++++
Total 1 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[1]">
<ParameterValueStruct>
<Name>Device.ManagementServer.URL</Name>
<Value xsi:type="xsd:string">http://AW1000.arcadyan.cwmp.bdms.telstra.net/cwmp/cwmp</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 571 bytes. nRemainbytes 0, ret 1
received 571 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 571 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.Time.
++++++++++++++Dump packet IN++++++++++++++
Call SyncDevice.Time.Func()
Total 9 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[9]">
<ParameterValueStruct>
<Name>Device.Time.Enable</Name>
<Value xsi:type="xsd:boolean">1</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.Status</Name>
<Value xsi:type="xsd:string">Synchronized</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.NTPServer1</Name>
<Value xsi:type="xsd:string">chronos.ntp.telstra.net</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.NTPServer2</Name>
<Value xsi:type="xsd:string">chronos1.ntp.telstra.net</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.NTPServer3</Name>
<Value xsi:type="xsd:string">0.au.pool.ntp.org</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.NTPServer4</Name>
<Value xsi:type="xsd:string">1.au.pool.ntp.org</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.NTPServer5</Name>
<Value xsi:type="xsd:string">2.au.pool.ntp.org</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.CurrentLocalTime</Name>
<Value xsi:type="xsd:dateTime">2022-03-10T09:03:53+11:00</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.Time.LocalTimeZone</Name>
<Value xsi:type="xsd:string">AEST-10AEDT,M10.1.0,M4.1.0/3</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 797 bytes. nRemainbytes 0, ret 1
received 797 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 797 bytes
--------------Dump packet IN--------------
cwmp:SetParameterValues
ParameterList
ParameterValueStruct
Name = Device.Time.LocalTimeZone
Value = AEST-10AEDT,M10.1.0,M4.1.0/3
ParameterKey = 1
++++++++++++++Dump packet IN++++++++++++++
Call SetDevice.Time.Func()
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:SetParameterValuesResponse>
<Status>0</Status>
</cwmp:SetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
[arca.dbus.mng -> arca.dbus.misc: (Action: tr69_ntp Param: {}) ["arca.dbus.misc:ntpclient CMD_RESTART"]]
[arca.dbus.misc received: ["arca.dbus.misc:ntpclient CMD_RESTART"]]
[arca.dbus.misc -> arca.dbus.mng: ["FWD_SUCCESS"]]
953 line: [HTTP/1.1 200 OK
]try to get 652 bytes. nRemainbytes 0, ret 1
received 652 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 652 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.ManagementServer.PeriodicInformInterval
string = Device.BulkData.Profile.1.Name
++++++++++++++Dump packet IN++++++++++++++
Call SyncDevice.BulkData.Func()
Call SyncDevice.BulkData.Profile.Func()
Total 2 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[2]">
<ParameterValueStruct>
<Name>Device.ManagementServer.PeriodicInformInterval</Name>
<Value xsi:type="xsd:unsignedInt">86400</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.BulkData.Profile.1.Name</Name>
<Value xsi:type="xsd:string">Telstra08Jul2021v1</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 594 bytes. nRemainbytes 0, ret 1
received 594 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 594 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.PPP.InterfaceNumberOfEntries
++++++++++++++Dump packet IN++++++++++++++
Total 1 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[1]">
<ParameterValueStruct>
<Name>Device.PPP.InterfaceNumberOfEntries</Name>
<Value xsi:type="xsd:unsignedInt">1</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 580 bytes. nRemainbytes 0, ret 1
received 580 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 580 bytes
--------------Dump packet IN--------------
cwmp:GetParameterValues
ParameterNames
string = Device.PPP.Interface.
++++++++++++++Dump packet IN++++++++++++++
Total 49 Parameters
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:GetParameterValuesResponse>
<ParameterList SOAP-ENC:arrayType="cwmp:ParameterValueStruct[49]">
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Enable</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Status</Name>
<Value xsi:type="xsd:string">LowerLayerDown</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Alias</Name>
<Value xsi:type="xsd:string">WAN</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Name</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LastChange</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LowerLayers</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCPEnable</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPv6CPEnable</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Reset</Name>
<Value xsi:type="xsd:boolean">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.ConnectionStatus</Name>
<Value xsi:type="xsd:string">Unconfigured</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LastConnectionError</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.AutoDisconnectTime</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IdleDisconnectTime</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.WarnDisconnectDelay</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Username</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Password</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.EncryptionProtocol</Name>
<Value xsi:type="xsd:string">None</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.CompressionProtocol</Name>
<Value xsi:type="xsd:string">None</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.AuthenticationProtocol</Name>
<Value xsi:type="xsd:string">CHAP</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.MaxMRUSize</Name>
<Value xsi:type="xsd:unsignedInt">1500</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.CurrentMRUSize</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.ConnectionTrigger</Name>
<Value xsi:type="xsd:string">AlwaysOn</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LCPEcho</Name>
<Value xsi:type="xsd:unsignedInt">30</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.LCPEchoRetry</Name>
<Value xsi:type="xsd:unsignedInt">5</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.PPPoE.SessionID</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.PPPoE.ACName</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.PPPoE.ServiceName</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.LocalIPAddress</Name>
<Value xsi:type="xsd:string">0.0.0.0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.RemoteIPAddress</Name>
<Value xsi:type="xsd:string">0.0.0.0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.DNSServers</Name>
<Value xsi:type="xsd:string">101.168.244.103,101.168.244.101</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.PassthroughEnable</Name>
<Value xsi:type="xsd:boolean">1</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPCP.PassthroughDHCPPool</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPv6CP.LocalInterfaceIdentifier</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.IPv6CP.RemoteInterfaceIdentifier</Name>
<Value xsi:type="xsd:string"></Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BytesSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BytesReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.PacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.PacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.ErrorsSent</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.ErrorsReceived</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.UnicastPacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.UnicastPacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.DiscardPacketsSent</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.DiscardPacketsReceived</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.MulticastPacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.MulticastPacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BroadcastPacketsSent</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.BroadcastPacketsReceived</Name>
<Value xsi:type="xsd:unsignedLong">0</Value>
</ParameterValueStruct>
<ParameterValueStruct>
<Name>Device.PPP.Interface.1.Stats.UnknownProtoPacketsReceived</Name>
<Value xsi:type="xsd:unsignedInt">0</Value>
</ParameterValueStruct>
</ParameterList>
</cwmp:GetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 200 OK
]try to get 966 bytes. nRemainbytes 0, ret 1
received 966 bytes, respSize 128000
[ht_client_send]: Get status code [200]
recv 966 bytes
--------------Dump packet IN--------------
cwmp:SetParameterValues
ParameterList
ParameterValueStruct
Name = Device.IP.Diagnostics.DownloadDiagnostics.NumberOfConnections
Value = 4
ParameterValueStruct
Name = Device.IP.Diagnostics.UploadDiagnostics.NumberOfConnections
Value = 4
ParameterKey = 1
++++++++++++++Dump packet IN++++++++++++++
Call SyncDevice.IP.Func()
Call SyncDevice.IP.Diagnostics.Func()
Call SyncDevice.IP.Diagnostics.DownloadDiagnostics.Func()
Call SyncDevice.IP.Diagnostics.UploadDiagnostics.Func()
Call SetDevice.IP.Diagnostics.DownloadDiagnostics.Func()
Call SetDevice.IP.Diagnostics.UploadDiagnostics.Func()
<SOAP-ENV:Envelope
xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/"
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:cwmp="urn:dslforum-org:cwmp-1-2">
<SOAP-ENV:Header>
<cwmp:ID SOAP-ENV:mustUnderstand="1">1</cwmp:ID>
</SOAP-ENV:Header>
<SOAP-ENV:Body>
<cwmp:SetParameterValuesResponse>
<Status>0</Status>
</cwmp:SetParameterValuesResponse>
</SOAP-ENV:Body>
</SOAP-ENV:Envelope>
use the previous record...
====== [do again] ======
Cookie for aw1000.arcadyan.cwmp.bdms.telstra.net: JSESSIONID=BDF6FD6B59BCE87FFD89A2A1D860BB36
[ht_client_send]: Connect OK
953 line: [HTTP/1.1 204 No Content
]process_http_response(): unsupported status code=204
[ht_client_send]: Get status code [204]
recv 0 bytes
Tr69SoapOutput: Null response.
Tr69SoapOutput: Sending null Post.
Tr69SoapOutput: End of session.
write_config:127 --> start
[CFG_SaveAllConfigure(1045)] FileName:/etc/config/.glbcfg, Need space = 211699
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment