ak6l

/*
VFO program for Si5351
Using I2C LCD from:
http://www.amazon.com/Huhushop-TM-Serial-Display-Arduino/dp/B00JM88A94/
Si5351 library from NT7S.
Uses the updated version of the library (master).
Updated with the format_freq routine from Tom AK2B

Display library is avaible from:
https://code.google.com/p/u8glib/

UNO and 328 boards: Encoder on pin 2 and 3. Center pin to GND.
Leonardo: Encoder on pin 0 and 1. Center pin to GND.
100nF from each of the encoder pins to gnd is used to debounce
The pushbutton goes to pin 6 to set the tuning rate.

Pin 7 is the RX/TX pin. Put this pin LOW for RX, open or high for TX.
Single transistor switch to +RX will work.

VFO will NOT tune in TX.

In serial monitor, you can send "F"+frequency to set frequency. Ex: "F7063000"

IF frequency is positive for sum product (IF = RF + LO) and negative for diff (IF = RF - LO)
VFO signal output on CLK0, BFO signal on CLK2
TODO:
* Write own OLED i2c library with optimizing for text to reduce size of compiled program.
*Add variable tuning resolution
*/

volatile unsigned long frequency = 144400000; // This will be the frequency it always starts on.
long freqstep[] = {50, 100, 500, 1000, 5000, 10000}; // set this to your wanted tuning rate in Hz.
int corr = 120; // this is the correction factor for the Si5351, use calibration sketch to find value.
long iffreq = 0; // set the IF frequency in Hz.

#include "U8glib.h"
//U8GLIB_SSD1306_128X32 u8g(U8G_I2C_OPT_NONE);	// I2C / TWI

U8GLIB_SSD1306_128X64 u8g(10, 9, 12, 11, 13);  // SW SPI Com: SCK = 10, MOSI = 9, CS = 12, D0 = 11, RESET = 13

String str;
char b[8];
int inData;
String displayFreq;
boolean A_set = false;
boolean B_set = false;
unsigned int lastReportedPos = 1;   // change management
static boolean rotating = false;    // debounce management

#include <si5351.h>
#include "Wire.h"
Si5351 si5351;
// int encoderPinA ;
//int encoderPinB;
#if defined(__AVR_ATmega32U4__) || defined(__AVR_ATmega16U4__)
int encoderPinA = 0;
int encoderPinB = 1;
#endif
#if defined(__AVR_ATmega328P__) || defined(__AVR_ATmega168__)
int encoderPinA = 2;
int  encoderPinB = 3;
#endif
bool tx;
int txpin = 7;
int freqsteps = 1;
int bandbutton = 6;
#define arraylength       (sizeof(freqstep) / sizeof(freqstep[0]))



void setup()
{
  // set the encoder to inputs
  pinMode(encoderPinA, INPUT);
  pinMode(encoderPinB, INPUT);
  pinMode(txpin, INPUT);
  pinMode(bandbutton, INPUT);
  // turn on pullup resistors
  digitalWrite(encoderPinA, HIGH);
  digitalWrite(encoderPinB, HIGH);
  digitalWrite(txpin, HIGH);
  digitalWrite(bandbutton, HIGH );
  u8g.setFont(u8g_font_courB12);
  Serial.begin(9600);
  // Initialize the Si5351
  // Change the 2nd parameter in init if using a ref osc other
  // than 25 MHz
  si5351.init(SI5351_CRYSTAL_LOAD_8PF, 0);

  si5351.set_correction(corr);

  si5351.drive_strength(SI5351_CLK0, SI5351_DRIVE_4MA);
  si5351.drive_strength(SI5351_CLK2, SI5351_DRIVE_4MA);
  // assign default color value
  if ( u8g.getMode() == U8G_MODE_R3G3B2 ) {
    u8g.setColorIndex(255);     // white
  }
  else if ( u8g.getMode() == U8G_MODE_GRAY2BIT ) {
    u8g.setColorIndex(3);         // max intensity
  }
  else if ( u8g.getMode() == U8G_MODE_BW ) {
    u8g.setColorIndex(1);         // pixel on
  }
  else if ( u8g.getMode() == U8G_MODE_HICOLOR ) {
    u8g.setHiColorByRGB(255, 255, 255);
  }

#if defined(__AVR_ATmega32U4__) || defined(__AVR_ATmega16U4__)
  encoderPinA = 0;
  encoderPinB = 1;
  //Code in here will only be compiled if an Arduino Leonardo is used.
  // encoder pin on interrupt 2 (pin 0)
  attachInterrupt(2, doEncoderA, CHANGE);
  // encoder pin on interrupt 3 (pin 1)
  attachInterrupt(3, doEncoderB, CHANGE);
#endif
#if defined(__AVR_ATmega328P__) || defined(__AVR_ATmega168__)
  encoderPinA = 2;
  encoderPinB = 3;
  //Code in here will only be compiled if an Arduino Uno (or older) is used.
  attachInterrupt(0, doEncoderA, CHANGE);
  // encoder pin on interrupt 1 (pin 1)
  attachInterrupt(1, doEncoderB, CHANGE);
#endif


}


void loop()
{
  tx = digitalRead(txpin);
  rotating = true;  // reset the debouncer

  if ( lastReportedPos != frequency) {
    lastReportedPos = frequency;
    //  Serial.print(frequency); // unncomment this to output frequency on change.
    si5351.set_freq((frequency + iffreq) * 100ULL, 0, SI5351_CLK0);
  }

  if (digitalRead(bandbutton) == LOW ) {
    delay(150);   // delay to debounce
    if (digitalRead(bandbutton) == LOW ) {
      freqsteps = freqsteps + 1;
      Serial.print(freqstep[freqsteps - 1]);
      Serial.print("     ");
      Serial.print(freqsteps);
      Serial.print("      ");
      Serial.println(sizeof(freqstep));
      if (freqsteps > arraylength - 1 ) {
        freqsteps = 0;
      }
      delay(1000); //delay to avoid many steps at one
    }
  }
  format_freq();
  

  // rebuild the picture after some delay
  delay(50);

  if (Serial.available() > 0)   // see if incoming serial data:
  {
    inData = Serial.read();  // read oldest byte in serial buffer:
  }
  if (inData == 'F') {
    frequency = Serial.parseInt();
    inData = 0;
  }
}


// Interrupt on A changing state
void doEncoderA() {
  // debounce
  if ( rotating ) delay (1);  // wait a little until the bouncing is done
  // Test transition, did things really change?
  if ( digitalRead(encoderPinA) != A_set ) { // debounce once more
    A_set = !A_set;
    // adjust counter + if A leads B
    if ( A_set && !B_set ) {
      if (!tx) {
        frequency += freqstep[freqsteps]; // hehre is the amount to increase the freq
      }
      rotating = false;  // no more debouncing until loop() hits again
    }
  }
}

// Interrupt on B changing state, same as A above
void doEncoderB() {
  if ( rotating ) delay (1);
  if ( digitalRead(encoderPinB) != B_set ) {
    B_set = !B_set;
    //  adjust counter - 1 if B leads A
    if ( B_set && !A_set ) {
      if (!tx) {
        frequency -= freqstep[freqsteps]; // here is the amount to decrease the freq
      }
      rotating = false;
    }
  }
}
void format_freq() {
  u8g.firstPage();
  do {
    u8g.setPrintPos(0,15);
     uint16_t f, g;
  f = frequency / 1000000;
  if (f < 10)
    u8g.print(' ');
  u8g.print(f);
  u8g.print('.');
  f = (frequency % 1000000) / 1000;
  if (f < 100)
    u8g.print('0');
  if (f < 10)
    u8g.print('0');
  u8g.print(f);
  u8g.print('.');
  f = frequency % 1000;
  if (f < 100)
    u8g.print('0');
  if (f < 10)
    u8g.print('0');
  u8g.print(f);
  u8g.setPrintPos(80,32);
   u8g.println(freqstep[freqsteps]);
   if (tx)
  {
    u8g.drawStr( 110, 15, "TX" );
  }
    //draw();
  } while ( u8g.nextPage() );
}