How to make an up-to-date OpenWRT image for loading onto a Raspberry Pi Compute Module 4 with a DFRobot Router Carrier Board.

How-To.md

The background is that the default OpenWRT image for Raspberry Pi lacks drivers for the LAN port (RTL8111) on the DFRobot board. DFRobot provide an image, but that one is made from a quite old daily snapshot of OpenWRT which is not entirely stable. Also, it is better to know how to fish than be given a fish.

DFRobot's page about the router board:
https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767

OpenWRT main page:
https://openwrt.org/

You are expected to have some general knowledge on Linux and OpenWRT. The instructions for flashing the resulting firmware image are presented on DFRobot's page.

We will use the OpenWRT image builder. This is a quite nifty tool that can generate a firmware image with some additional packages not present in the default image. It is not a cross-compiler, but rather takes already compiled OpenWRT packages and creates a new firmware image.

Download the latest image builder for Raspberry Pi from OpenWRT. At the time of writing, this is RC3. It is under target bcm27xx/bcm2711
https://downloads.openwrt.org/releases/21.02.0-rc3/targets/bcm27xx/bcm2711/

I built it on a Debian VirtualBox machine, but pretty much any Linux system would do. You first need to install some Linux tools. These are the tools for Debian/Ubuntu:

root@debian:~# apt install build-essential libncurses5-dev libncursesw5-dev zlib1g-dev gawk git gettext libssl-dev xsltproc rsync wget unzip python

For other Linux distros, see the Prerequisites section here:
https://openwrt.org/docs/guide-user/additional-software/imagebuilder

Unpack your image builder:

martin@debian:~# tar Jxf openwrt-imagebuilder-21.02.0-rc3-bcm27xx-bcm2711.Linux-x86_64.tar.xz
martin@debian:~# cd openwrt-imagebuilder-21.02.0-rc3-bcm27xx-bcm2711.Linux-x86_64/

For some reason, you will need a /etc/config/network file in your image, or your LAN network will not come up.
https://openwrt.org/docs/guide-user/additional-software/imagebuilder#files_variable

martin@debian:~# mkdir -p files/etc/config

Put below file in files/etc/config/network

We need to build the image with 3 extra modules:

• luci -- the OpenWRT web interface
• kmod-r8169 -- kernel module for the DFRobot ethernet controller
• kmod-usb-dwc2 -- kernel module for USB. More details:
  https://openwrt.org/packages/pkgdata/kmod-usb-dwc2
  https://raspberrypi.stackexchange.com/questions/77059/what-does-dtoverlay-dwc2-really-do#77061

Go!

martin@debian:~# make image PROFILE="rpi-4" PACKAGES="luci kmod-r8169 kmod-usb-dwc2" FILES=files/

The built image(s) will end up at:
bin/targets/bcm27xx/bcm2711/

The “default” one to use would be:
openwrt-21.02.0-rc3-bcm27xx-bcm2711-rpi-4-ext4-factory.img.gz

After you gunzip that file, you can follow the instructions from DFRobot for installation. Or you can use “dd” directly on Linux, instead of Rufus:

martin@debian:~# dd if=/home/martin/openwrt/openwrt-21.02.0-rc3-bcm27xx-bcm2711-rpi-4-ext4-factory.img of=/dev/sdb

network

config interface 'loopback'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'
        option device 'lo'

config globals 'globals'
        option ula_prefix 'fdff:ac50:10da::/48'

config interface 'wan'
        option proto 'dhcp'
        option device 'eth0'

config interface 'lan'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option device 'eth1'

@ripplecart

Happy it worked for you. I noticed the missing orange LED myself, but both ethtool on the router and the switch on the other end report 1000Mbit/s full duplex, so I didn't dig deeper ;-)

Same issue here, no orange LED on the RJ45 interface

@bit2016

As I mentioned, you can easily verify with ethtool that the link actually is Gigabit. This is a cosmetic error.

root@claudius:~# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 0
        Transceiver: external
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: d
        Current message level: 0x00000033 (51)
                               drv probe ifdown ifup
        Link detected: yes

@martin-niklasson Is there an easy way to Compile it in Windows 11 with SubSystem Linux? Have some problems with it, cause it won't let me update Python to the Version required to Build... Also Now 22.03.0 is Released so you could update your readme, no need to add Luci anymore i think?
Also where exatly to place the Network before compile? Mine seems to fail, unless it just have something with wrong version of Python I use... Could I mabye ask you to compile it for me, only need I have is to change the Network IP for lan to 192.168.144.10

Hi @martin-niklasson did you manage to create an image for the DFRobot board under OpenWRT 23.05.0 yet? I'm having troubles with bcm27xx-userland

Collected errors:
 * opkg_conf_parse_file: Duplicate src declaration (openwrt_core https://downloads.openwrt.org/releases/23.05.0/targets/bcm27xx/bcm2711/packages). Skipping.
 * opkg_conf_parse_file: Duplicate src declaration (openwrt_base https://downloads.openwrt.org/releases/23.05.0/packages/aarch64_cortex-a72/base). Skipping.
 * opkg_conf_parse_file: Duplicate src declaration (openwrt_luci https://downloads.openwrt.org/releases/23.05.0/packages/aarch64_cortex-a72/luci). Skipping.
 * opkg_conf_parse_file: Duplicate src declaration (openwrt_packages https://downloads.openwrt.org/releases/23.05.0/packages/aarch64_cortex-a72/packages). Skipping.
 * opkg_conf_parse_file: Duplicate src declaration (openwrt_routing https://downloads.openwrt.org/releases/23.05.0/packages/aarch64_cortex-a72/routing). Skipping.
 * opkg_conf_parse_file: Duplicate src declaration (openwrt_telephony https://downloads.openwrt.org/releases/23.05.0/packages/aarch64_cortex-a72/telephony). Skipping.