Created
December 23, 2014 13:19
-
-
Save martinusadyh/a3f8fc0ff247f3137ac0 to your computer and use it in GitHub Desktop.
SmartMonTools Log
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
$ sudo smartctl -a /dev/sdb | |
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-24-generic] (local build) | |
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org | |
=== START OF INFORMATION SECTION === | |
Model Family: Seagate Momentus 5400.6 | |
Device Model: ST9500325AS | |
Serial Number: 5VEND3AM | |
LU WWN Device Id: 5 000c50 04510ebf8 | |
Firmware Version: 0005HPM1 | |
User Capacity: 500,107,862,016 bytes [500 GB] | |
Sector Size: 512 bytes logical/physical | |
Rotation Rate: 5400 rpm | |
Device is: In smartctl database [for details use: -P show] | |
ATA Version is: ATA8-ACS T13/1699-D revision 4 | |
SATA Version is: SATA 2.6, 3.0 Gb/s | |
Local Time is: Tue Dec 23 20:16:52 2014 WIB | |
SMART support is: Available - device has SMART capability. | |
SMART support is: Enabled | |
=== START OF READ SMART DATA SECTION === | |
SMART overall-health self-assessment test result: PASSED | |
General SMART Values: | |
Offline data collection status: (0x00) Offline data collection activity | |
was never started. | |
Auto Offline Data Collection: Disabled. | |
Self-test execution status: ( 0) The previous self-test routine completed | |
without error or no self-test has ever | |
been run. | |
Total time to complete Offline | |
data collection: ( 0) seconds. | |
Offline data collection | |
capabilities: (0x53) SMART execute Offline immediate. | |
Auto Offline data collection on/off support. | |
Suspend Offline collection upon new | |
command. | |
No Offline surface scan supported. | |
Self-test supported. | |
No Conveyance Self-test supported. | |
Selective Self-test supported. | |
SMART capabilities: (0x0003) Saves SMART data before entering | |
power-saving mode. | |
Supports SMART auto save timer. | |
Error logging capability: (0x01) Error logging supported. | |
General Purpose Logging supported. | |
Short self-test routine | |
recommended polling time: ( 2) minutes. | |
Extended self-test routine | |
recommended polling time: ( 136) minutes. | |
SCT capabilities: (0x103f) SCT Status supported. | |
SCT Error Recovery Control supported. | |
SCT Feature Control supported. | |
SCT Data Table supported. | |
SMART Attributes Data Structure revision number: 10 | |
Vendor Specific SMART Attributes with Thresholds: | |
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | |
1 Raw_Read_Error_Rate 0x000f 110 099 006 Pre-fail Always - 26191450 | |
3 Spin_Up_Time 0x0002 099 098 000 Old_age Always - 0 | |
4 Start_Stop_Count 0x0033 097 097 000 Pre-fail Always - 3445 | |
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 | |
7 Seek_Error_Rate 0x000f 083 060 030 Pre-fail Always - 217577101 | |
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 10415 | |
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 | |
12 Power_Cycle_Count 0x0033 098 098 020 Pre-fail Always - 2317 | |
183 Runtime_Bad_Block 0x0032 100 253 000 Old_age Always - 701 | |
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0 | |
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 | |
188 Command_Timeout 0x0032 100 001 000 Old_age Always - 1413 | |
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 | |
190 Airflow_Temperature_Cel 0x0022 069 054 045 Old_age Always - 31 (Min/Max 29/31) | |
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 152 | |
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 143 | |
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 12049 | |
194 Temperature_Celsius 0x0022 031 046 000 Old_age Always - 31 (0 20 0 0 0) | |
195 Hardware_ECC_Recovered 0x001a 052 025 000 Old_age Always - 26191450 | |
196 Reallocated_Event_Count 0x0033 100 100 036 Pre-fail Always - 0 | |
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 | |
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 | |
199 UDMA_CRC_Error_Count 0x003e 200 195 000 Old_age Always - 740 | |
SMART Error Log Version: 1 | |
ATA Error Count: 6 (device log contains only the most recent five errors) | |
CR = Command Register [HEX] | |
FR = Features Register [HEX] | |
SC = Sector Count Register [HEX] | |
SN = Sector Number Register [HEX] | |
CL = Cylinder Low Register [HEX] | |
CH = Cylinder High Register [HEX] | |
DH = Device/Head Register [HEX] | |
DC = Device Command Register [HEX] | |
ER = Error register [HEX] | |
ST = Status register [HEX] | |
Powered_Up_Time is measured from power on, and printed as | |
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, | |
SS=sec, and sss=millisec. It "wraps" after 49.710 days. | |
Error 6 occurred at disk power-on lifetime: 10380 hours (432 days + 12 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
04 71 04 81 87 80 e0 Device Fault; Error: ABRT | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
a1 00 00 00 00 00 a0 00 05:48:04.055 IDENTIFY PACKET DEVICE | |
ec 00 00 00 00 00 a0 00 05:48:04.055 IDENTIFY DEVICE | |
ff 00 00 00 00 00 00 00 05:48:03.743 [VENDOR SPECIFIC] | |
00 00 00 00 00 00 00 ff 05:48:03.743 NOP [Abort queued commands] | |
a1 00 00 00 00 00 a0 00 05:47:58.727 IDENTIFY PACKET DEVICE | |
Error 5 occurred at disk power-on lifetime: 10380 hours (432 days + 12 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
04 71 04 81 87 80 e0 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
ec 00 00 00 00 00 a0 00 05:48:04.055 IDENTIFY DEVICE | |
ff 00 00 00 00 00 00 00 05:48:03.743 [VENDOR SPECIFIC] | |
00 00 00 00 00 00 00 ff 05:48:03.743 NOP [Abort queued commands] | |
a1 00 00 00 00 00 a0 00 05:47:58.727 IDENTIFY PACKET DEVICE | |
ec 00 00 00 00 00 a0 00 05:47:58.726 IDENTIFY DEVICE | |
Error 4 occurred at disk power-on lifetime: 10380 hours (432 days + 12 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
04 71 04 81 87 80 e0 Device Fault; Error: ABRT | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
a1 00 00 00 00 00 a0 00 05:47:58.727 IDENTIFY PACKET DEVICE | |
ec 00 00 00 00 00 a0 00 05:47:58.726 IDENTIFY DEVICE | |
ff 00 00 00 00 00 00 00 05:47:58.414 [VENDOR SPECIFIC] | |
00 00 00 00 00 00 00 ff 05:47:58.414 NOP [Abort queued commands] | |
a1 00 00 00 00 00 a0 00 05:47:53.435 IDENTIFY PACKET DEVICE | |
Error 3 occurred at disk power-on lifetime: 10380 hours (432 days + 12 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
04 71 04 81 87 80 e0 | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
ec 00 00 00 00 00 a0 00 05:47:58.726 IDENTIFY DEVICE | |
ff 00 00 00 00 00 00 00 05:47:58.414 [VENDOR SPECIFIC] | |
00 00 00 00 00 00 00 ff 05:47:58.414 NOP [Abort queued commands] | |
a1 00 00 00 00 00 a0 00 05:47:53.435 IDENTIFY PACKET DEVICE | |
ec 00 00 00 00 00 a0 00 05:47:53.398 IDENTIFY DEVICE | |
Error 2 occurred at disk power-on lifetime: 10380 hours (432 days + 12 hours) | |
When the command that caused the error occurred, the device was active or idle. | |
After command completion occurred, registers were: | |
ER ST SC SN CL CH DH | |
-- -- -- -- -- -- -- | |
04 71 04 81 87 80 e0 Device Fault; Error: ABRT | |
Commands leading to the command that caused the error were: | |
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name | |
-- -- -- -- -- -- -- -- ---------------- -------------------- | |
a1 00 00 00 00 00 a0 00 05:47:53.435 IDENTIFY PACKET DEVICE | |
ec 00 00 00 00 00 a0 00 05:47:53.398 IDENTIFY DEVICE | |
00 00 00 00 00 00 00 ff 05:47:53.087 NOP [Abort queued commands] | |
61 00 00 ff ff ff 4f 00 05:47:52.980 WRITE FPDMA QUEUED | |
61 00 00 ff ff ff 4f 00 05:47:52.980 WRITE FPDMA QUEUED | |
SMART Self-test log structure revision number 1 | |
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | |
# 1 Extended offline Completed without error 00% 10393 - | |
# 2 Short offline Completed without error 00% 10391 - | |
# 3 Short offline Completed without error 00% 10389 - | |
# 4 Short offline Aborted by host 90% 10183 - | |
# 5 Short offline Aborted by host 90% 9725 - | |
# 6 Extended offline Aborted by host 90% 3 - | |
# 7 Short offline Completed without error 00% 3 - | |
SMART Selective self-test log data structure revision number 1 | |
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | |
1 0 0 Not_testing | |
2 0 0 Not_testing | |
3 0 0 Not_testing | |
4 0 0 Not_testing | |
5 0 0 Not_testing | |
Selective self-test flags (0x0): | |
After scanning selected spans, do NOT read-scan remainder of disk. | |
If Selective self-test is pending on power-up, resume after 0 minute delay. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment