ls1043v-funtoo-boot.txt

U-Boot SPL 2017.05-rc2-00075-gab77ba7bb2-dirty (Aug 24 2017 - 16:52:20)
Initializing DDR....
Trying to boot from NAND


U-Boot 2017.05-rc2-00075-gab77ba7bb2-dirty (Aug 24 2017 - 16:52:20 +1000)

SoC:  LS1043AE Rev1.1 (0x87920011)
Clock Configuration:
       CPU0(A53):1600 MHz  CPU1(A53):1600 MHz  CPU2(A53):1600 MHz  
       CPU3(A53):1600 MHz  
       Bus:      400  MHz  DDR:      1600 MT/s  FMAN:     500  MHz
Reset Configuration Word (RCW):
       00000000: 08100010 0a000000 00000000 00000000
       00000010: 14550002 00804012 e0025000 c1002000
       00000020: 00000000 00000000 00000000 00038800
       00000030: 00000000 00001100 00000096 00000001
Model: Traverse LS1043V
Board: LS1043V, booting from NAND
I2C:   ready
DRAM:  Detected UDIMM Fixed DDR on board
2 GiB (DDR4, 32-bit, CL=11, ECC off)
Using SERDES1 Protocol: 5205 (0x1455)
SEC0: RNG instantiated
ppa_init: fdt_check_header() failed
Waking secondary cores to start from ffd05000
All (4) cores are up.
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Net:   Fman1: Uploading microcode version 106.4.18
Setting AR8035 output clock
PCIe0: pcie@3400000 disabled
PCIe1: pcie@3500000 Root Complex: no link
PCIe2: pcie@3600000 Root Complex: no link
FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3 [PRIME], FM1@DTSEC4, FM1@DTSEC5, FM1@DTSEC6, FM1@TGEC1
Hit any key to stop autoboot: 10  9  8  7  6  5  4  3  2  1  0 
reading uEnv.txt
164 bytes read in 9 ms (17.6 KiB/s)
## Warning: defaulting to text format
reading kernel.itb
3407639 bytes read in 161 ms (20.2 MiB/s)
## Loading kernel from FIT Image at a0000000 ...
   Using 'config@1' configuration
   Trying 'kernel@1' kernel subimage
     Description:  ARM64 Linux kernel
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0xa00000c4
     Data Size:    3383841 Bytes = 3.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x80080000
     Entry Point:  0x80080000
   Verifying Hash Integrity ... OK
## Loading fdt from FIT Image at a0000000 ...
   Using 'config@1' configuration
   Trying 'fdt@1' fdt subimage
     Description:  Flattened Device Tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xa033a39c
     Data Size:    23096 Bytes = 22.6 KiB
     Architecture: AArch64
   Verifying Hash Integrity ... OK
   Loading fdt from 0xa033a39c to 0x90000000
   Booting using the fdt blob at 0x90000000
   Uncompressing Kernel Image ... OK
   Using Device Tree in place at 0000000090000000, end 0000000090018a37

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] random: get_random_bytes called from start_kernel+0x30/0x3c0 with crng_init=0
[    0.000000] Linux version 4.13.0-rc4+ (matt@development) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3978+443-e209988)) #5 SMP Tue Aug 22 12:42:33 AEST 2017
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Machine model: Traverse LS1043V
[    0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000ff800000, size 4 MiB
[    0.000000] OF: reserved mem: initialized node qman-fqd, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000fc000000, size 32 MiB
[    0.000000] OF: reserved mem: initialized node qman-pfdr, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x00000000fe000000, size 16 MiB
[    0.000000] OF: reserved mem: initialized node bman-fbpr, compatible id shared-dma-pool
[    0.000000] percpu: Embedded 23 pages/cpu @ffffffc07fd76000 s53528 r8192 d32488 u94208
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 503303
[    0.000000] Kernel command line: console=ttyS0,115200 earlycon=uart8250,mmio,0x21c0500 root=/dev/mmcblk0p2 rootdelay=20
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Memory: 2002088K/2041856K available (4924K kernel code, 314K rwdata, 1384K rodata, 384K init, 334K bss, 39768K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008550000   (  4928 KB)
[    0.000000]     .rodata : 0xffffff8008550000 - 0xffffff80086b0000   (  1408 KB)
[    0.000000]       .init : 0xffffff80086b0000 - 0xffffff8008710000   (   384 KB)
[    0.000000]       .data : 0xffffff8008710000 - 0xffffff800875ea00   (   315 KB)
[    0.000000]        .bss : 0xffffff800875ea00 - 0xffffff80087b24e8   (   335 KB)
[    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000]               0xffffffbf00000000 - 0xffffffbf01bf9000   (    27 MB actual)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc07fe00000   (  2046 MB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x000000000142f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858
[    0.000000] arch_timer: CPU0: Trapping CNTVCT access
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.008284] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000)
[    0.018689] pid_max: default: 32768 minimum: 301
[    0.023401] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.030142] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.037772] ASID allocator initialised with 65536 entries
[    0.043227] Hierarchical SRCU implementation.
[    0.047804] EFI services will not be available.
[    0.052416] smp: Bringing up secondary CPUs ...
[    0.057107] Detected VIPT I-cache on CPU1
[    0.057127] arch_timer: CPU1: Trapping CNTVCT access
[    0.057131] CPU1: Booted secondary processor [410fd034]
[    0.057286] Detected VIPT I-cache on CPU2
[    0.057298] arch_timer: CPU2: Trapping CNTVCT access
[    0.057301] CPU2: Booted secondary processor [410fd034]
[    0.057449] Detected VIPT I-cache on CPU3
[    0.057461] arch_timer: CPU3: Trapping CNTVCT access
[    0.057464] CPU3: Booted secondary processor [410fd034]
[    0.057489] smp: Brought up 1 node, 4 CPUs
[    0.104353] SMP: Total of 4 processors activated.
[    0.109077] CPU features: detected feature: 32-bit EL0 Support
[    0.114939] CPU: All CPU(s) started at EL2
[    0.119058] alternatives: patching kernel code
[    0.124135] devtmpfs: initialized
[    0.129715] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.139512] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.146172] DMI not present or invalid.
[    0.146181] random: fast init done
[    0.153545] NET: Registered protocol family 16
[    0.158630] vdso: 2 pages (1 code @ ffffff8008555000, 1 data @ ffffff8008714000)
[    0.166171] DMA: preallocated 256 KiB pool for atomic allocations
[    0.172294] Serial: AMBA PL011 UART driver
[    0.177104] Machine: Traverse LS1043V
[    0.180782] SoC family: QorIQ LS1043A
[    0.184453] SoC ID: svr:0x87920011, Revision: 1.1
[    0.197998] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.204958] ACPI: Interpreter disabled.
[    0.209018] SCSI subsystem initialized
[    0.212993] usbcore: registered new interface driver usbfs
[    0.218544] usbcore: registered new interface driver hub
[    0.223909] usbcore: registered new device driver usb
[    0.229176] imx-i2c 2180000.i2c: can't get pinctrl, bus recovery not supported
[    0.313050] pca953x 0-0020: interrupt support not compiled in
[    0.318925] i2c i2c-0: IMX I2C adapter registered
[    0.323659] i2c i2c-0: can't use DMA, using PIO instead.
[    0.329208] dmi: Firmware registration failed.
[    0.333713] fsl-ifc 1530000.ifc: Freescale Integrated Flash Controller
[    0.340284] fsl-ifc 1530000.ifc: IFC version 1.4, 8 banks
[    0.346150] clocksource: Switched to clocksource arch_sys_counter
[    0.352389] pnp: PnP ACPI: disabled
[    0.356580] NET: Registered protocol family 2
[    0.361183] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.368539] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.375376] TCP: Hash tables configured (established 16384 bind 16384)
[    0.381993] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.388056] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.394650] NET: Registered protocol family 1
[    0.399167] RPC: Registered named UNIX socket transport module.
[    0.405116] RPC: Registered udp transport module.
[    0.409840] RPC: Registered tcp transport module.
[    0.414564] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.421684] workingset: timestamp_bits=62 max_order=19 bucket_order=0
[    0.428431] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.434395] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.442933] io scheduler noop registered (default)
[    0.447749] io scheduler mq-deadline registered
[    0.452298] io scheduler kyber registered
[    0.456368] atomic64_test: passed
[    0.460148] OF: PCI: host bridge /soc/pcie@3500000 ranges:
[    0.465669] OF: PCI:    IO 0x4800010000..0x480001ffff -> 0x00000000
[    0.471970] OF: PCI:   MEM 0x4840000000..0x487fffffff -> 0x40000000
[    0.478360] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0000:00
[    0.485105] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.490623] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.496836] pci_bus 0000:00: root bus resource [mem 0x4840000000-0x487fffffff] (bus address [0x40000000-0x7fffffff])
[    0.507573] pci 0000:00:00.0: bridge configuration invalid ([bus 02-02]), reconfiguring
[    0.515701] pci 0000:00:00.0: BAR 6: assigned [mem 0x4840000000-0x48400007ff pref]
[    0.523314] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.528469] pcieport 0000:00:00.0: AER enabled with IRQ 64
[    0.534022] OF: PCI: host bridge /soc/pcie@3600000 ranges:
[    0.539539] OF: PCI:    IO 0x5000010000..0x500001ffff -> 0x00000000
[    0.545839] OF: PCI:   MEM 0x5040000000..0x507fffffff -> 0x40000000
[    0.552205] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0001:00
[    0.558948] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.564462] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x0000-0xffff])
[    0.573474] pci_bus 0001:00: root bus resource [mem 0x5040000000-0x507fffffff] (bus address [0x40000000-0x7fffffff])
[    0.584191] pci 0001:00:00.0: bridge configuration invalid ([bus 04-04]), reconfiguring
[    0.592311] pci 0001:00:00.0: BAR 6: assigned [mem 0x5040000000-0x50400007ff pref]
[    0.599922] pci 0001:00:00.0: PCI bridge to [bus 01]
[    0.605042] pcieport 0001:00:00.0: AER enabled with IRQ 65
[    0.610881] bman_ccsr 1890000.bman: assigned reserved memory node bman-fbpr
[    0.621400] qman_ccsr 1880000.qman: assigned reserved memory node qman-fqd
[    0.629172] qman_ccsr 1880000.qman: assigned reserved memory node qman-pfdr
[    0.643005] qman_ccsr 1880000.qman: Allocated PFDR 0xfc000000 0x2000000
[    0.650886] bman_portal 508000000.bman-portal: Portal initialised, cpu 0
[    0.657657] bman_portal 508010000.bman-portal: Portal initialised, cpu 1
[    0.664428] bman_portal 508020000.bman-portal: Portal initialised, cpu 2
[    0.671196] bman_portal 508030000.bman-portal: Portal initialised, cpu 3
[    0.678106] qman_portal 500000000.qman-portal: Portal initialised, cpu 0
[    0.684879] qman_portal 500010000.qman-portal: Portal initialised, cpu 1
[    0.691653] qman_portal 500020000.qman-portal: Portal initialised, cpu 2
[    0.698556] qman_portal 500030000.qman-portal: Portal initialised, cpu 3
[    0.705408] bman_test: bman_test_api(): Starting
[    0.710267] bman_test: bman_test_api(): Finished
[    0.714906] qman_test_api(): Starting
[    0.718589] VDQCR (till-empty);
[    0.721823] VDQCR (4 of 10);
[    0.724787] VDQCR (6 of 10);
[    0.727754] scheduled dequeue (till-empty)
[    0.731945] Retirement message received
[    0.735806] qman_test_api(): Finished
[    0.739625] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.746482] console [ttyS0] disabled
[    0.750085] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 35, base_baud = 25000000) is a 16550A
[    0.758936] console [ttyS0] enabled
[    0.758936] console [ttyS0] enabled
[    0.765914] bootconsole [uart8250] disabled
[    0.765914] bootconsole [uart8250] disabled
[    0.774424] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 35, base_baud = 25000000) is a 16550A
[    0.783296] of_serial: probe of 21d0500.serial failed with error -28
[    0.789696] of_serial: probe of 21d0600.serial failed with error -28
[    0.799383] brd: module loaded
[    0.805144] loop: module loaded
[    0.809629] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xac
[    0.815986] nand: Micron MT29F4G08ABBDAHC
[    0.819990] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.827819] Bad block table found at page 262080, version 0x01
[    0.834121] Bad block table found at page 262016, version 0x01
[    0.840558] fsl,ifc-nand 7e800000.nand: IFC NAND device at 0x7e800000, bank 0
[    0.847865] libphy: Fixed MDIO Bus: probed
[    0.852997] libphy: Freescale XGMAC MDIO Bus: probed
[    0.859155] libphy: Freescale XGMAC MDIO Bus: probed
[    0.864461] libphy: Freescale XGMAC MDIO Bus: probed
[    0.869803] libphy: Freescale XGMAC MDIO Bus: probed
[    0.875140] libphy: Freescale XGMAC MDIO Bus: probed
[    0.880485] libphy: Freescale XGMAC MDIO Bus: probed
[    0.885823] libphy: Freescale XGMAC MDIO Bus: probed
[    0.891161] libphy: Freescale XGMAC MDIO Bus: probed
[    0.896445] libphy: Freescale XGMAC MDIO Bus: probed
[    0.915772] fsl_mac 1ae0000.ethernet: FMan MEMAC
[    0.920391] fsl_mac 1ae0000.ethernet: FMan MAC address: 00:0a:fa:24:23:31
[    0.927511] fsl_mac 1ae2000.ethernet: FMan MEMAC
[    0.932126] fsl_mac 1ae2000.ethernet: FMan MAC address: 00:0a:fa:24:23:32
[    0.939007] fsl_mac 1ae4000.ethernet: FMan MEMAC
[    0.943622] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:0a:fa:24:23:35
[    0.950576] fsl_mac 1ae6000.ethernet: FMan MEMAC
[    0.955194] fsl_mac 1ae6000.ethernet: FMan MAC address: 00:0a:fa:24:23:36
[    0.962315] fsl_mac 1ae8000.ethernet: FMan MEMAC
[    0.966929] fsl_mac 1ae8000.ethernet: FMan MAC address: 00:0a:fa:24:23:33
[    0.974046] fsl_mac 1aea000.ethernet: FMan MEMAC
[    0.978661] fsl_mac 1aea000.ethernet: FMan MAC address: 00:0a:fa:24:23:34
[    0.988399] fsl_dpa dpaa-ethernet.0 eth0: Probed interface eth0
[    0.997144] fsl_dpa dpaa-ethernet.1 eth1: Probed interface eth1
[    1.005895] fsl_dpa dpaa-ethernet.2 eth2: Probed interface eth2
[    1.014635] fsl_dpa dpaa-ethernet.3 eth3: Probed interface eth3
[    1.023358] fsl_dpa dpaa-ethernet.4 eth4: Probed interface eth4
[    1.032078] fsl_dpa dpaa-ethernet.5 eth5: Probed interface eth5
[    1.045810] rtc-isl1208 0-006f: rtc core: registered rtc-isl1208 as rtc0
[    1.053119] i2c /dev entries driver
[    1.056959] sdhci: Secure Digital Host Controller Interface driver
[    1.063135] sdhci: Copyright(c) Pierre Ossman
[    1.067484] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.110161] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit
[    1.135144] NET: Registered protocol family 10
[    1.140184] Segment Routing with IPv6
[    1.143870] NET: Registered protocol family 17
[    1.148325] 8021q: 802.1Q VLAN Support v1.8
[    1.155102] rtc-isl1208 0-006f: setting system clock to 2017-08-31 01:42:43 UTC (1504143763)
[    1.164069] Waiting 20 sec before mounting root device...
[    1.178081] mmc0: new high speed SDHC card at address e624
[    1.183699] mmcblk0: mmc0:e624 SL16G 14.8 GiB 
[    1.189064]  mmcblk0: p1 p2 p3
[   21.557449] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[   21.565875] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[   21.588048] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[   21.596155] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[   21.611537] devtmpfs: mounted
[   21.614596] Freeing unused kernel memory: 384K
INIT: version 2.88 booting

   OpenRC 0.23.2 is starting up Funtoo Linux (aarch64)

 * Mounting /proc ...
 [ ok ]
 * Mounting /run ...
 * /run/openrc: creating directory
 * /run/lock: creating directory
 * /run/lock: correcting owner
 * Caching service dependencies ...
 [ ok ]
 * Remounting devtmpfs on /dev ...
 [ ok ]
 * Mounting /dev/mqueue ...
 [ ok ]
 * Mounting /dev/pts ...
 [ ok ]
 * Mounting /dev/shm ...
 [ ok ]
 * Creating list of required static device nodes for the current kernel ...
Warning: /lib/modules/4.13.0-rc4+/modules.devname not found - ignoring
 [ ok ]
 * Mounting /sys ...
 [ ok ]
 * Mounting debug filesystem ...
 [ ok ]
 * Mounting cgroup filesystem ...
 [ ok ]
 * Starting udev ...
 [ ok ]
 * Generating a rule to create a /dev/root symlink ...
 [ ok ]
 * Populating /dev with existing devices through uevents ...
 [ ok ]
 * Waiting for uevents to be processed ...
 [ ok ]
 * Setting system clock using the hardware clock [UTC] ...
 [ ok ]
 * Checking local filesystems  ...
/dev/mmcblk0p2: clean, 314381/920272 files, 1613672/3678720 blocks
 [ ok ]
 * Remounting root filesystem read/write ...
 [ ok ]
 * Remounting filesystems ...
 [ ok ]
 * Updating /etc/mtab ...
 * Creating mtab symbolic link
 [ ok ]
 * Activating swap devices ...
 [ ok ]
 * Mounting local filesystems ...
 [ ok ]
 * Loading custom binary format handlers ...
 [ ok ]
 * Configuring kernel parameters ...
 [ ok ]
 * Creating user login records ...
 [ ok ]
 * Wiping /tmp directory ...
 [ ok ]
 * Configuring /etc/hosts ...
 [ ok ]
 * Setting hostname to ls1043 ...
 [ ok ]
 * Setting terminal encoding [UTF-8] ...
/etc/init.d/termencoding: line 40: /dev/tty1: No such device or address
 [ ok ]
 * Setting keyboard mode [UTF-8] ...
Couldn't open /dev/tty1
Couldn't open /dev/tty2
Couldn't open /dev/tty3
Couldn't open /dev/tty4
Couldn't open /dev/tty5
Couldn't open /dev/tty6
Couldn't open /dev/tty7
Couldn't open /dev/tty8
Couldn't open /dev/tty9
Couldn't open /dev/tty10
Couldn't open /dev/tty11
Couldn't open /dev/tty12
 [ ok ]
 * Loading key mappings [us] ...
Couldn't get a file descriptor referring to the console
 * Error loading key mappings
 [ !! ]
 * ERROR: keymaps failed to start
 * Bringing up network interface lo ...
 [ ok ]
 * Initializing random number generator ...
 [ ok ]
INIT: Entering runlevel: 3
 * Checking rsyslogd's configuration ...
 [ ok ]
 * Starting rsyslog ...
 [ ok ]
 * Starting dnsmasq ...
 [ ok ]
 * Setting keyboard mode [UTF-8] ...
Couldn't open /dev/tty1
Couldn't open /dev/tty2
Couldn't open /dev/tty3
Couldn't open /dev/tty4
Couldn't open /dev/tty5
Couldn't open /dev/tty6
Couldn't open /dev/tty7
Couldn't open /dev/tty8
Couldn't open /dev/tty9
Couldn't open /dev/tty10
Couldn't open /dev/tty11
Couldn't open /dev/tty12
 [ ok ]
 * Loading key mappings [us] ...
Couldn't get a file descriptor referring to the console
 * Error loading key mappings
 [ !! ]
 * ERROR: keymaps failed to start
 * Network dhcpcd eth2 up ...
eth2: waiting for carrier
eth2: carrier acquired
DUID 00:01:00:01:21:32:3f:01:00:0a:fa:24:23:35
eth2: IAID fa:24:23:35
eth2: adding address fe80::f246:528:a70:8241
eth2: soliciting an IPv6 router
eth2: soliciting a DHCP lease
eth2: offered 192.168.0.143 from 192.168.0.1
eth2: probing address 192.168.0.143/24
eth2: Router Advertisement from fe80::20a:faff:fe28:c958
eth2: confirming prior DHCPv6 lease
eth2: leased 192.168.0.143 for 43200 seconds
eth2: adding route to 192.168.0.0/24
eth2: adding default route via 192.168.0.1
forked to background, child pid 1781
 [ ok ]
 * Mounting network filesystems ...
 [ ok ]
 * Starting postfix (/etc/postfix) ...
postfix/postfix-script: warning: not owned by root: /var/spool/postfix/.
postfix/postfix-script: starting the Postfix mail system
 [ ok ]
 * Starting sshd ...
 [ ok ]
 * Starting local ...
 [ ok ]

ls1043.unknown_domain (Linux aarch64 4.13.0-rc4+) 01:43:30

ls1043 login: root
Password: 
Last login: Wed Aug 30 05:14:56 -00 2017 on ttyS0

 >>> Release:                       stage3-arm64_generic-funtoo-current-2017-06-05
 >>> Version:                       2017-06-05
 >>> Created by:                    Daniel Robbins <drobbins@funtoo.org>

 >>> Send suggestions, improvements, bug reports relating to...

 >>> This release:                  Daniel Robbins <drobbins@funtoo.org>
 >>> Funtoo Linux (general):        Funtoo Linux (http://www.funtoo.org)
 >>> Gentoo Linux (general):        Gentoo Linux (http://www.gentoo.org)

 NOTE: This message can be removed by deleting /etc/motd.

ls1043 ~ # cat /proc/cpuinfo 
processor	: 0
BogoMIPS	: 50.00
Features	: fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer	: 0x41
CPU architecture: 8
CPU variant	: 0x0
CPU part	: 0xd03
CPU revision	: 4

processor	: 1
BogoMIPS	: 50.00
Features	: fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer	: 0x41
CPU architecture: 8
CPU variant	: 0x0
CPU part	: 0xd03
CPU revision	: 4

processor	: 2
BogoMIPS	: 50.00
Features	: fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer	: 0x41
CPU architecture: 8
CPU variant	: 0x0
CPU part	: 0xd03
CPU revision	: 4

processor	: 3
BogoMIPS	: 50.00
Features	: fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer	: 0x41
CPU architecture: 8
CPU variant	: 0x0
CPU part	: 0xd03
CPU revision	: 4

ls1043 ~ #