gistfile1.txt

[    0.000000][    T0] Linux version 6.5.0-rc6-00003-gb131740d8c1f (gcc (GCC) 8.5.0 20210514 (Red Hat 8.5.0-20), GNU ld version 2.30-121.el8) #100 SMP PREEMPT_DYNAMIC Fri Aug 18 07:37:29 PDT 2023
[    0.000000][    T0] Command line: panic=10 libata.dma=0 libata.force=noncq root=/dev/ram0 rw console=ttyS0 scsi_mod.scan=sync debug ip=dhcp
[    0.000000][    T0] BIOS-provided physical RAM map:
[    0.000000][    T0] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000][    T0] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000][    T0] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000][    T0] BIOS-e820: [mem 0x0000000000100000-0x0000000031fdffff] usable
[    0.000000][    T0] BIOS-e820: [mem 0x0000000031fe0000-0x0000000031ffffff] reserved
[    0.000000][    T0] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[    0.000000][    T0] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[    0.000000][    T0] NX (Execute Disable) protection: active
[    0.000000][    T0] SMBIOS 2.8 present.
[    0.000000][    T0] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[    0.000000][    T0] tsc: Fast TSC calibration using PIT
[    0.000000][    T0] tsc: Detected 2200.014 MHz processor
[    0.001071][    T0] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.001075][    T0] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.001079][    T0] last_pfn = 0x31fe0 max_arch_pfn = 0x400000000
[    0.001104][    T0] MTRR map: 4 entries (3 fixed + 1 variable; max 19), built from 8 variable MTRRs
[    0.001110][    T0] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.001209][    T0] Using GB pages for direct mapping
[    0.001506][    T0] RAMDISK: [mem 0x28125000-0x31fdffff]
[    0.001526][    T0] ACPI: Early table checksum verification disabled
[    0.001552][    T0] ACPI: RSDP 0x00000000000F58C0 000014 (v00 BOCHS )
[    0.001559][    T0] ACPI: RSDT 0x0000000031FE1550 000034 (v01 BOCHS  BXPCRSDT 00000001 BXPC 00000001)
[    0.001573][    T0] ACPI: FACP 0x0000000031FE1404 000074 (v01 BOCHS  BXPCFACP 00000001 BXPC 00000001)
[    0.001580][    T0] ACPI: DSDT 0x0000000031FE0040 0013C4 (v01 BOCHS  BXPCDSDT 00000001 BXPC 00000001)
[    0.001584][    T0] ACPI: FACS 0x0000000031FE0000 000040
[    0.001587][    T0] ACPI: APIC 0x0000000031FE1478 000078 (v01 BOCHS  BXPCAPIC 00000001 BXPC 00000001)
[    0.001591][    T0] ACPI: HPET 0x0000000031FE14F0 000038 (v01 BOCHS  BXPCHPET 00000001 BXPC 00000001)
[    0.001594][    T0] ACPI: WAET 0x0000000031FE1528 000028 (v01 BOCHS  BXPCWAET 00000001 BXPC 00000001)
[    0.001597][    T0] ACPI: Reserving FACP table memory at [mem 0x31fe1404-0x31fe1477]
[    0.001598][    T0] ACPI: Reserving DSDT table memory at [mem 0x31fe0040-0x31fe1403]
[    0.001599][    T0] ACPI: Reserving FACS table memory at [mem 0x31fe0000-0x31fe003f]
[    0.001600][    T0] ACPI: Reserving APIC table memory at [mem 0x31fe1478-0x31fe14ef]
[    0.001601][    T0] ACPI: Reserving HPET table memory at [mem 0x31fe14f0-0x31fe1527]
[    0.001602][    T0] ACPI: Reserving WAET table memory at [mem 0x31fe1528-0x31fe154f]
[    0.001734][    T0] No NUMA configuration found
[    0.001735][    T0] Faking a node at [mem 0x0000000000000000-0x0000000031fdffff]
[    0.001740][    T0] NODE_DATA(0) allocated [mem 0x28122000-0x28124fff]
[    0.001775][    T0] Zone ranges:
[    0.001775][    T0]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.001777][    T0]   DMA32    [mem 0x0000000001000000-0x0000000031fdffff]
[    0.001779][    T0]   Normal   empty
[    0.001780][    T0]   Device   empty
[    0.001781][    T0] Movable zone start for each node
[    0.001782][    T0] Early memory node ranges
[    0.001782][    T0]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.001786][    T0]   node   0: [mem 0x0000000000100000-0x0000000031fdffff]
[    0.001789][    T0] Initmem setup node 0 [mem 0x0000000000001000-0x0000000031fdffff]
[    0.001799][    T0] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.001838][    T0] On node 0, zone DMA: 97 pages in unavailable ranges
[    0.004571][    T0] On node 0, zone DMA32: 24608 pages in unavailable ranges
[    0.004998][    T0] ACPI: PM-Timer IO Port: 0x608
[    0.005018][    T0] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.005065][    T0] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[    0.005069][    T0] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.005071][    T0] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[    0.005072][    T0] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.005076][    T0] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[    0.005077][    T0] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[    0.005082][    T0] ACPI: Using ACPI (MADT) for SMP configuration information
[    0.005083][    T0] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.005088][    T0] TSC deadline timer available
[    0.005091][    T0] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[    0.005116][    T0] [mem 0x32000000-0xfeffbfff] available for PCI devices
[    0.005128][    T0] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[    0.013994][    T0] setup_percpu: NR_CPUS:512 nr_cpumask_bits:1 nr_cpu_ids:1 nr_node_ids:1
[    0.014379][    T0] percpu: Embedded 58 pages/cpu s208896 r0 d28672 u2097152
[    0.014387][    T0] pcpu-alloc: s208896 r0 d28672 u2097152 alloc=1*2097152
[    0.014391][    T0] pcpu-alloc: [0] 0 
[    0.014405][    T0] Kernel command line: panic=10 libata.dma=0 libata.force=noncq pm80xx.logging_level_dis=0xfffff root=/dev/ram0 rw console=ttyS0 scsi_mod.scan=sync debug ip=dhcp
[    0.014561][    T0] Unknown kernel command line parameters "ip=dhcp", will be passed to user space.
[    0.014614][    T0] random: crng init done
[    0.014776][    T0] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.014814][    T0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.014871][    T0] Fallback order for Node 0: 0 
[    0.014879][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 201312
[    0.014880][    T0] Policy zone: DMA32
[    0.014883][    T0] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.017744][    T0] Memory: 571476K/818680K available (22528K kernel code, 10011K rwdata, 20040K rodata, 2080K init, 5496K bss, 246948K reserved, 0K cma-reserved)
[    0.017807][    T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.017843][    T0] ftrace: allocating 69814 entries in 273 pages
[    0.033951][    T0] ftrace: allocated 273 pages with 3 groups
[    0.035441][    T0] Dynamic Preempt: none
[    0.035467][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.035468][    T0] rcu: 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=1.
[    0.035470][    T0] 	Trampoline variant of Tasks RCU enabled.
[    0.035470][    T0] 	Rude variant of Tasks RCU enabled.
[    0.035471][    T0] 	Tracing variant of Tasks RCU enabled.
[    0.035471][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[    0.035472][    T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.039702][    T0] NR_IRQS: 33024, nr_irqs: 256, preallocated irqs: 16
[    0.039896][    T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.045519][    T0] Console: colour VGA+ 80x25
[    0.045561][    T0] printk: console [ttyS0] enabled
[    0.162240][    T0] ACPI: Core revision 20230331
[    0.163180][    T0] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[    0.164984][    T0] APIC: Switch to symmetric I/O mode setup
[    0.166282][    T0] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.168932][    T0] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.174945][    T0] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x1fb64003b85, max_idle_ns: 440795259466 ns
[    0.176837][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 4400.02 BogoMIPS (lpj=2200014)
[    0.178462][    T0] x86/cpu: User Mode Instruction Prevention (UMIP) activated
[    0.179851][    T0] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[    0.180727][    T0] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[    0.180857][    T0] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.181837][    T0] Spectre V2 : Kernel not compiled with retpoline; no mitigation available!
[    0.181838][    T0] Spectre V2 : Vulnerable
[    0.183834][    T0] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.184834][    T0] Speculative Store Bypass: Vulnerable
[    0.185858][    T0] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.186834][    T0] TAA: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.187834][    T0] MMIO Stale Data: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.188852][    T0] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.189836][    T0] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.190834][    T0] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.191834][    T0] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.192834][    T0] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[    0.208425][    T0] Freeing SMP alternatives memory: 64K
[    0.208836][    T0] pid_max: default: 32768 minimum: 301
[    0.209862][    T0] LSM: initializing lsm=capability,selinux,integrity
[    0.210837][    T0] SELinux:  Initializing.
[    0.211898][    T0] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.212836][    T0] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.214139][    T1] smpboot: CPU0: Intel(R) Pentium(R) CPU D1508 @ 2.20GHz (family: 0x6, model: 0x56, stepping: 0x3)
[    0.214987][    T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.215854][    T1] RCU Tasks Rude: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.216856][    T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.217850][    T1] Performance Events: Broadwell events, full-width counters, Intel PMU driver.
[    0.218839][    T1] ... version:                2
[    0.219650][    T1] ... bit width:              48
[    0.219836][    T1] ... generic registers:      4
[    0.220646][    T1] ... value mask:             0000ffffffffffff
[    0.220835][    T1] ... max period:             00007fffffffffff
[    0.221835][    T1] ... fixed-purpose events:   3
[    0.222641][    T1] ... event mask:             000000070000000f
[    0.222964][    T1] signal: max sigframe size: 1776
[    0.223849][    T1] rcu: Hierarchical SRCU implementation.
[    0.224790][    T1] rcu: 	Max phase no-delay instances is 400.
[    0.225033][    T1] smp: Bringing up secondary CPUs ...
[    0.225852][    T1] smp: Brought up 1 node, 1 CPU
[    0.226653][    T1] smpboot: Max logical packages: 1
[    0.226836][    T1] smpboot: Total of 1 processors activated (4400.02 BogoMIPS)
[    0.228058][    T1] devtmpfs: initialized
[    0.228811][    T1] x86/mm: Memory block size: 128MB
[    0.229193][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.229841][    T1] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.231038][    T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.232020][    T1] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.232846][    T1] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.233842][    T1] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.234849][    T1] audit: initializing netlink subsys (disabled)
[    0.235998][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.236001][    T1] thermal_sys: Registered thermal governor 'user_space'
[    0.236857][   T22] audit: type=2000 audit(1692376064.068:1): state=initialized audit_enabled=0 res=1
[    0.238843][    T1] cpuidle: using governor menu
[    0.240018][    T1] dca service started, version 1.12.1
[    0.240906][    T1] PCI: Using configuration type 1 for base access
[    0.453671][    T1] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.453836][    T1] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
[    0.454835][    T1] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.455835][    T1] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[    0.456966][    T1] cryptd: max_cpu_qlen set to 1000
[    0.473834][    T1] raid6: avx2x4   gen() 24678 MB/s
[    0.490834][    T1] raid6: avx2x2   gen() 24635 MB/s
[    0.507835][    T1] raid6: avx2x1   gen() 21618 MB/s
[    0.508551][    T1] raid6: using algorithm avx2x4 gen() 24678 MB/s
[    0.525835][    T1] raid6: .... xor() 8429 MB/s, rmw enabled
[    0.526841][    T1] raid6: using avx2x2 recovery algorithm
[    0.527891][    T1] ACPI: Added _OSI(Module Device)
[    0.528837][    T1] ACPI: Added _OSI(Processor Device)
[    0.529840][    T1] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.530840][    T1] ACPI: Added _OSI(Processor Aggregator Device)
[    0.532243][    T1] ACPI: 1 ACPI AML tables successfully acquired and loaded
[    0.533228][    T1] ACPI: Interpreter enabled
[    0.533844][    T1] ACPI: PM: (supports S0 S5)
[    0.534836][    T1] ACPI: Using IOAPIC for interrupt routing
[    0.535855][    T1] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.536836][    T1] PCI: Using E820 reservations for host bridge windows
[    0.537916][    T1] ACPI: Enabled 2 GPEs in block 00 to 0F
[    0.540313][    T1] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.540843][    T1] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI EDR HPX-Type3]
[    0.541836][    T1] acpi PNP0A03:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
[    0.542849][    T1] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended configuration space under this bridge
[    0.543961][    T1] PCI host bridge to bus 0000:00
[    0.544801][    T1] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.544836][    T1] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.545842][    T1] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.546842][    T1] pci_bus 0000:00: root bus resource [mem 0x32000000-0xfebfffff window]
[    0.547841][    T1] pci_bus 0000:00: root bus resource [mem 0x100000000-0x17fffffff window]
[    0.548841][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.549902][    T1] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[    0.551250][    T1] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100
[    0.552455][    T1] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180
[    0.554794][    T1] pci 0000:00:01.1: reg 0x20: [io  0xc040-0xc04f]
[    0.555611][    T1] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.555842][    T1] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.556841][    T1] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.557840][    T1] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.559015][    T1] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000
[    0.560259][    T1] pci 0000:00:01.3: quirk: [io  0x0600-0x063f] claimed by PIIX4 ACPI
[    0.560844][    T1] pci 0000:00:01.3: quirk: [io  0x0700-0x070f] claimed by PIIX4 SMB
[    0.562025][    T1] pci 0000:00:02.0: [1234:1111] type 00 class 0x030000
[    0.563878][    T1] pci 0000:00:02.0: reg 0x10: [mem 0xfd000000-0xfdffffff pref]
[    0.566876][    T1] pci 0000:00:02.0: reg 0x18: [mem 0xfebd0000-0xfebd0fff]
[    0.571876][    T1] pci 0000:00:02.0: reg 0x30: [mem 0xfeba0000-0xfebaffff pref]
[    0.572933][    T1] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.574128][    T1] pci 0000:00:03.0: [8086:100e] type 00 class 0x020000
[    0.575529][    T1] pci 0000:00:03.0: reg 0x10: [mem 0xfeb80000-0xfeb9ffff]
[    0.576600][    T1] pci 0000:00:03.0: reg 0x14: [io  0xc000-0xc03f]
[    0.579548][    T1] pci 0000:00:03.0: reg 0x30: [mem 0xfeb00000-0xfeb3ffff pref]
[    0.580117][    T1] pci 0000:00:04.0: [9005:8074] type 00 class 0x010700
[    0.581899][    T1] pci 0000:00:04.0: reg 0x10: [mem 0xfebb0000-0xfebbffff 64bit]
[    0.583874][    T1] pci 0000:00:04.0: reg 0x18: [mem 0xfebc0000-0xfebcffff 64bit]
[    0.586875][    T1] pci 0000:00:04.0: reg 0x24: [mem 0xfeb40000-0xfeb7ffff]
[    0.589962][    T1] pci 0000:00:04.0: supports D1
[    0.590731][    T1] pci 0000:00:04.0: 31.504 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x4 link at 0000:00:04.0 (capable of 63.008 Gb/s with 8.0 GT/s PCIe x8 link)
[    0.591567][    T1] ACPI: PCI: Interrupt link LNKA configured for IRQ 10
[    0.591929][    T1] ACPI: PCI: Interrupt link LNKB configured for IRQ 10
[    0.592919][    T1] ACPI: PCI: Interrupt link LNKC configured for IRQ 11
[    0.593920][    T1] ACPI: PCI: Interrupt link LNKD configured for IRQ 11
[    0.595895][    T1] ACPI: PCI: Interrupt link LNKS configured for IRQ 9
[    0.597202][    T1] iommu: Default domain type: Translated
[    0.597836][    T1] iommu: DMA domain TLB invalidation policy: lazy mode
[    0.598962][    T1] SCSI subsystem initialized
[    0.599634][    T1] libata version 3.00 loaded.
[    0.599872][    T1] ACPI: bus type USB registered
[    0.600581][    T1] usbcore: registered new interface driver usbfs
[    0.600847][    T1] usbcore: registered new interface driver hub
[    0.601722][    T1] usbcore: registered new device driver usb
[    0.601854][    T1] pps_core: LinuxPPS API ver. 1 registered
[    0.602672][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.602839][    T1] PTP clock support registered
[    0.603585][    T1] EDAC MC: Ver: 3.0.0
[    0.604306][    T1] PCI: Using ACPI for IRQ routing
[    0.604839][    T1] PCI: pci_cache_line_size set to 64 bytes
[    0.605762][    T1] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.605837][    T1] e820: reserve RAM buffer [mem 0x31fe0000-0x33ffffff]
[    0.606881][    T1] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.4)
[    0.607969][    T1] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.608784][    T1] hpet0: 3 comparators, 64-bit 100.000000 MHz counter
[    0.611884][    T1] clocksource: Switched to clocksource tsc-early
[    0.612862][    T1] VFS: Disk quotas dquot_6.6.0
[    0.613541][    T1] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.614673][    T1] FS-Cache: Loaded
[    0.627455][    T1] CacheFiles: Loaded
[    0.628083][    T1] pnp: PnP ACPI init
[    0.628733][    T1] pnp 00:02: [dma 2]
[    0.629508][    T1] pnp: PnP ACPI: found 6 devices
[    0.635538][    T1] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.636971][    T1] NET: Registered PF_INET protocol family
[    0.637842][    T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.639343][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.640667][    T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.641890][    T1] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.643119][    T1] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.644330][    T1] TCP: Hash tables configured (established 8192 bind 8192)
[    0.645381][    T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.646439][    T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.647588][    T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.649223][    T1] RPC: Registered named UNIX socket transport module.
[    0.650224][    T1] RPC: Registered udp transport module.
[    0.651020][    T1] RPC: Registered tcp transport module.
[    0.651804][    T1] RPC: Registered tcp-with-tls transport module.
[    0.652872][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.654097][    T1] NET: Registered PF_XDP protocol family
[    0.655074][    T1] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.656257][    T1] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.657439][    T1] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.658741][    T1] pci_bus 0000:00: resource 7 [mem 0x32000000-0xfebfffff window]
[    0.660040][    T1] pci_bus 0000:00: resource 8 [mem 0x100000000-0x17fffffff window]
[    0.661410][    T1] pci 0000:00:01.0: PIIX3: Enabling Passive Release
[    0.662539][    T1] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[    0.663757][    T1] PCI: CLS 32 bytes, default 64
[    0.664776][   T10] Trying to unpack rootfs image as initramfs...
[    0.681909][    T1] RAPL PMU: API unit is 2^-32 Joules, 0 fixed counters, 10737418240 ms ovfl timer
[    0.683547][    T1] mce: Machine check injector initialized
[    0.689203][    T1] Initialise system trusted keyrings
[    0.693899][    T1] workingset: timestamp_bits=43 max_order=18 bucket_order=0
[    0.695174][    T1] zbud: loaded
[    0.695928][    T1] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.697171][    T1] NFS: Registering the id_resolver key type
[    0.698183][    T1] Key type id_resolver registered
[    0.699035][    T1] Key type id_legacy registered
[    0.703849][    T1] fuse: init (API version 7.38)
[    0.704806][    T1] SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
[    0.718049][    T1] NET: Registered PF_ALG protocol family
[    0.719033][    T1] xor: measuring software checksum speed
[    0.720407][    T1]    prefetch64-sse  : 24024 MB/sec
[    0.721772][    T1]    generic_sse     : 20556 MB/sec
[    0.722650][    T1] xor: using function: prefetch64-sse (24024 MB/sec)
[    0.723779][    T1] async_tx: api initialized (async)
[    0.724657][    T1] Key type asymmetric registered
[    0.725485][    T1] Asymmetric key parser 'x509' registered
[    0.726540][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    0.744005][    T1] io scheduler mq-deadline registered
[    0.744945][    T1] io scheduler kyber registered
[    0.745783][    T1] io scheduler bfq registered
[    0.750049][    T1] switchtec: loaded.
[    0.750725][    T1] IPMI message handler: version 39.2
[    0.751632][    T1] ipmi device interface
[    0.755024][    T1] ipmi_si: IPMI System Interface driver
[    0.755963][    T1] ipmi_si: Unable to find any System Interface(s)
[    0.756885][    T1] IPMI Watchdog: driver initialized
[    0.757616][    T1] IPMI poweroff: Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot
[    0.759088][    T1] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.760287][    T1] ACPI: button: Power Button [PWRF]
[    0.769069][    T1] EINJ: EINJ table not found.
[    0.769757][    T1] ioatdma: Intel(R) QuickData Technology Driver 5.00
[    0.770807][    T1] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.771991][    T1] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.775633][    T1] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[    0.777104][    T1] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[    0.787651][    T1] brd: module loaded
[    0.789189][    T1] loop: module loaded
[    0.819106][    T1] zram: Added device: zram0
[    0.820372][    T1] null_blk: disk nullb0 created
[    0.821447][    T1] null_blk: module loaded
[    0.822582][    T1] pm80xx 0000:00:04.0: pm80xx: driver version 0.1.40
[    0.836708][    T1] ACPI: \_SB_.LNKD: Enabled at IRQ 11
[    0.859917][    T1] :: pm8001_pci_alloc 546: Setting link rate to default value
[    0.861583][    T1] pm80xx0:: pm8001_ioremap 500: base addr febb0000 virt_addr=ffffc900006f0000 len=65536
[    0.863735][    T1] pm80xx0:: pm8001_ioremap 500: base addr febc0000 virt_addr=ffffc90000710000 len=65536
[    0.865874][    T1] pm80xx0:: pm8001_ioremap 500: base addr feb40000 virt_addr=ffffc90000740000 len=262144
[    0.868034][    T1] pm80xx0:: pm8001_alloc 297: pm8001_alloc: PHY:8
[    0.873259][    T1] pm80xx0:: pm8001_setup_msix 992: pci_alloc_irq_vectors request ret:2 no of intr 2
[    0.874606][    T1] pm80xx0:: pm8001_request_msix 1007: pci_enable_msix request number of intr 2
[    0.876440][    T1] pm80xx0:: init_pci_device_addresses 1120: Scratchpad 0 PCI BAR: 0
[    0.877609][    T1] pm80xx0:: init_pci_device_addresses 1146: VALID main config signature 0x53434d50
[    0.878943][    T1] pm80xx0:: init_pci_device_addresses 1167: GST OFFSET 0xc4
[    0.879989][    T1] pm80xx0:: init_pci_device_addresses 1169: INBND OFFSET 0x20000128
[    0.881087][    T1] pm80xx0:: init_pci_device_addresses 1171: OBND OFFSET 0x24000928
[    0.882198][    T1] pm80xx0:: init_pci_device_addresses 1173: IVT OFFSET 0x8001408
[    0.883270][    T1] pm80xx0:: init_pci_device_addresses 1175: PSPA OFFSET 0x8001608
[    0.884363][    T1] pm80xx0:: init_pci_device_addresses 1178: addr - main cfg 000000004bb4fd31 general status 000000001235b67d
[    0.886017][    T1] pm80xx0:: init_pci_device_addresses 1181: addr - inbnd 00000000e60f09dc obnd 00000000f4613e36
[    0.887475][    T1] pm80xx0:: init_pci_device_addresses 1184: addr - pspa 000000000242f737 ivt 00000000f4e9d8ee
[    1.736039][    T9] tsc: Refined TSC clocksource calibration: 2199.996 MHz
[    1.737061][    T9] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1fb62f12e8c, max_idle_ns: 440795238402 ns
[    1.738663][    T9] clocksource: Switched to clocksource tsc
[    2.649093][   T10] Freeing initrd memory: 162540K
[   33.889930][    T1] pm80xx0:: mpi_uninit_check 1528: TIMEOUT:IBDB value/=2
[   33.891360][    T1] pm80xx0:: pm80xx_chip_soft_rst 1611: MPI state is not ready scratch: 40002000:280e:2000:6c00481a
[   33.893423][    T1] pm80xx0:: pm80xx_chip_soft_rst 1622: reset register before write : 0x40
[   34.399919][    T1] pm80xx0:: pm80xx_chip_soft_rst 1629: reset register after write 0x40
[   34.884919][    T1] pm80xx0:: pm80xx_chip_soft_rst 1690: SPCv soft reset Complete
[   34.929968][    T1] pm80xx0:: init_pci_device_addresses 1120: Scratchpad 0 PCI BAR: 0
[   34.931711][    T1] pm80xx0:: init_pci_device_addresses 1146: VALID main config signature 0x53434d50
[   34.933500][    T1] pm80xx0:: init_pci_device_addresses 1167: GST OFFSET 0xc4
[   34.934909][    T1] pm80xx0:: init_pci_device_addresses 1169: INBND OFFSET 0x20000128
[   34.936434][    T1] pm80xx0:: init_pci_device_addresses 1171: OBND OFFSET 0x24000928
[   34.937944][    T1] pm80xx0:: init_pci_device_addresses 1173: IVT OFFSET 0x8001408
[   34.939419][    T1] pm80xx0:: init_pci_device_addresses 1175: PSPA OFFSET 0x8001608
[   34.940916][    T1] pm80xx0:: init_pci_device_addresses 1178: addr - main cfg 000000004bb4fd31 general status 000000001235b67d
[   34.943145][    T1] pm80xx0:: init_pci_device_addresses 1181: addr - inbnd 00000000e60f09dc obnd 00000000f4613e36
[   34.945112][    T1] pm80xx0:: init_pci_device_addresses 1184: addr - pspa 000000000242f737 ivt 00000000f4e9d8ee
[   35.495925][    T1] pm80xx0:: pm80xx_chip_init 1468: MPI initialize successful!
[   35.500319][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1272: SASConfigPage.pageCode 0x00000004
[   35.502067][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1274: SASConfigPage.MST_MSI  0x00018000
[   35.503781][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1276: SASConfigPage.STP_SSP_MCT_TMO  0x00200020
[   35.505601][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1278: SASConfigPage.STP_FRM_TMO  0x05ff0000
[   35.507368][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1280: SASConfigPage.STP_IDLE_TMO  0x00000005
[   35.509146][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1282: SASConfigPage.OPNRJT_RTRY_INTVL  0x00000002
[   35.511012][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1284: SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO  0x00800080
[   35.512958][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1286: SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR  0x5b8e5b8e
[   35.514909][    T1] pm80xx0:: pm80xx_set_sas_protocol_timer_config 1288: SASConfigPage.MAX_AIP  0x00200000
[   35.516621][    T1] scsi host0: pm80xx
[   36.238798][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 0 sas_addr = ffffffffffffffff
[   36.240557][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 1 sas_addr = ffffffffffffffff
[   36.242151][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 2 sas_addr = ffffffffffffffff
[   36.243729][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 3 sas_addr = ffffffffffffffff
[   36.245302][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 4 sas_addr = 03ffffffffffffff
[   36.246878][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 5 sas_addr = 03ffffffffffffff
[   36.248443][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 6 sas_addr = 03ffffffffffffff
[   36.250022][    T1] pm80xx0:: pm8001_init_sas_add 755: phy 7 sas_addr = 03ffffffffffffff
[   36.252239][    T1] pm80xx0:: pm8001_set_phy_profile 4883: phy settings completed
[   36.253929][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 0
[   36.255548][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x0
[   36.289129][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x0 port_id:0x0
[   36.290104][   T25] sas: phy-0:0 added to port-0:0, phy_mask:0x1 (500e004abbbbbb7f)
[   36.492422][   T10] sas: DOING DISCOVERY on port 0, pid:10
[   36.493478][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.495138][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x0 device_id 16385
[   36.498176][   T10] sas: ex 500e004abbbbbb7f phy00:U:A attached: 500e004abbbbbb00 (stp)
[   36.499703][   T10] sas: ex 500e004abbbbbb7f phy01:D:0 attached: 0000000000000000 (no device)
[   36.501569][   T10] sas: ex 500e004abbbbbb7f phy02:U:A attached: 500e004abbbbbb02 (stp)
[   36.503138][   T10] sas: ex 500e004abbbbbb7f phy03:D:0 attached: 0000000000000000 (no device)
[   36.504823][   T10] sas: ex 500e004abbbbbb7f phy04:D:0 attached: 0000000000000000 (no device)
[   36.506802][   T10] sas: ex 500e004abbbbbb7f phy05:U:A attached: 500e004abbbbbb05 (stp)
[   36.508429][   T10] sas: ex 500e004abbbbbb7f phy06:D:0 attached: 0000000000000000 (no device)
[   36.510288][   T10] sas: ex 500e004abbbbbb7f phy07:U:1 attached: 0000000000000000 (no device)
[   36.512306][   T10] sas: ex 500e004abbbbbb7f phy08:U:A attached: 500e004abbbbbb08 (stp)
[   36.514273][   T10] sas: ex 500e004abbbbbb7f phy09:D:0 attached: 0000000000000000 (no device)
[   36.516361][   T10] sas: ex 500e004abbbbbb7f phy10:U:A attached: 500e004abbbbbb0a (stp)
[   36.517989][   T10] sas: ex 500e004abbbbbb7f phy11:D:0 attached: 0000000000000000 (no device)
[   36.519709][   T10] sas: ex 500e004abbbbbb7f phy12:D:0 attached: 0000000000000000 (no device)
[   36.521701][   T10] sas: ex 500e004abbbbbb7f phy13:U:A attached: 500e004abbbbbb0d (stp)
[   36.523333][   T10] sas: ex 500e004abbbbbb7f phy14:D:0 attached: 0000000000000000 (no device)
[   36.525425][   T10] sas: ex 500e004abbbbbb7f phy15:U:A attached: 500e004abbbbbb0f (stp)
[   36.527439][   T10] sas: ex 500e004abbbbbb7f phy16:U:A attached: 500e004abbbbbb10 (stp)
[   36.529098][   T10] sas: ex 500e004abbbbbb7f phy17:D:0 attached: 0000000000000000 (no device)
[   36.531341][   T10] sas: ex 500e004abbbbbb7f phy18:U:A attached: 500e004abbbbbb12 (stp)
[   36.533309][   T10] sas: ex 500e004abbbbbb7f phy19:D:0 attached: 0000000000000000 (no device)
[   36.535365][   T10] sas: ex 500e004abbbbbb7f phy20:D:0 attached: 0000000000000000 (no device)
[   36.537293][   T10] sas: ex 500e004abbbbbb7f phy21:D:0 attached: 0000000000000000 (no device)
[   36.539452][   T10] sas: ex 500e004abbbbbb7f phy22:U:B attached: ffffffffffffffff (host)
[   36.541375][   T10] sas: ex 500e004abbbbbb7f phy23:U:0 attached: 0000000000000000 (no device)
[   36.543109][   T10] sas: ex 500e004abbbbbb7f phy24:D:0 attached: 0000000000000000 (no device)
[   36.544835][   T10] sas: ex 500e004abbbbbb7f phy25:D:0 attached: 0000000000000000 (no device)
[   36.546959][   T10] sas: ex 500e004abbbbbb7f phy26:U:1 attached: 0000000000000000 (no device)
[   36.549091][   T10] sas: ex 500e004abbbbbb7f phy27:U:1 attached: 0000000000000000 (no device)
[   36.551210][   T10] sas: ex 500e004abbbbbb7f phy28:D:0 attached: 0000000000000000 (no device)
[   36.553294][   T10] sas: ex 500e004abbbbbb7f phy29:D:0 attached: 0000000000000000 (no device)
[   36.555700][   T10] sas: ex 500e004abbbbbb7f phy30:U:0 attached: 0000000000000000 (no device)
[   36.558039][   T10] sas: ex 500e004abbbbbb7f phy31:U:1 attached: 0000000000000000 (no device)
[   36.559985][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 1
[   36.561864][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x1
[   36.563653][   T10] sas: ex 500e004abbbbbb7f phy32:D:0 attached: 0000000000000000 (no device)
[   36.565342][   T10] sas: ex 500e004abbbbbb7f phy33:D:0 attached: 0000000000000000 (no device)
[   36.567213][   T10] sas: ex 500e004abbbbbb7f phy34:U:1 attached: 0000000000000000 (no device)
[   36.568941][   T10] sas: ex 500e004abbbbbb7f phy35:U:1 attached: 0000000000000000 (no device)
[   36.570431][   T10] sas: ex 500e004abbbbbb7f phy36:D:B attached: 500e004abbbbbb7e (host+target)
[   36.572014][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.573380][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x0 device_id 16386
[   36.574955][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.576316][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x2 device_id 16387
[   36.577891][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.579256][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x5 device_id 16388
[   36.580833][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.582211][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x8 device_id 16389
[   36.583846][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.585217][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0xa device_id 16390
[   36.586791][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.588160][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0xd device_id 16391
[   36.589808][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.591166][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0xf device_id 16392
[   36.592790][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.594138][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x10 device_id 16393
[   36.595131][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x1 port_id:0x0
[   36.797209][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.798590][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x12 device_id 16394
[   36.800059][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x0
[   36.801420][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x24 device_id 16395
[   36.853946][   T65] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[   36.855678][   T24] sas: ata1: end_device-0:0:0: dev error handler
[   36.857183][   T71] sas: ata2: end_device-0:0:2: dev error handler
[   36.858698][   T72] sas: ata3: end_device-0:0:5: dev error handler
[   36.860224][   T73] sas: ata4: end_device-0:0:8: dev error handler
[   36.861733][   T74] sas: ata5: end_device-0:0:10: dev error handler
[   36.863259][   T75] sas: ata6: end_device-0:0:13: dev error handler
[   36.864774][   T76] sas: ata7: end_device-0:0:15: dev error handler
[   36.865951][   T77] sas: ata8: end_device-0:0:16: dev error handler
[   36.867116][   T78] sas: ata9: end_device-0:0:18: dev error handler
[   36.871863][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 2
[   36.873332][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x2
[   37.139501][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x2 port_id:0x1
[   37.341385][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 3
[   37.342660][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x3
[   37.376253][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x3 port_id:0x0
[   37.647919][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 4
[   37.649199][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x4
[   37.682779][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x4 port_id:0x2
[   37.951927][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 5
[   37.954183][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x5
[   38.220307][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x5 port_id:0x3
[   38.422737][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 6
[   38.423918][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x6
[   38.457484][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x6 port_id:0x2
[   38.727909][    T1] pm80xx0:: pm80xx_chip_phy_start_req 4667: PHY START REQ for phy_id 7
[   38.729123][    C0] pm80xx0:: mpi_phy_start_resp 3363: phy start resp status:0x0, phyid:0x7
[   38.762709][    C0] pm80xx0:: mpi_hw_event 3440: HW_EVENT_SAS_PHY_UP phyid:0x7 port_id:0x2
[   39.121069][   T78] ata9.00: FORCE: horkage modified (noncq)
[   39.122224][   T78] ata9.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   39.123331][   T78] ata9.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   39.125174][   T72] ata3.00: FORCE: horkage modified (noncq)
[   39.126407][   T76] ata7.00: FORCE: horkage modified (noncq)
[   39.127393][   T71] ata2.00: FORCE: horkage modified (noncq)
[   39.128368][   T75] ata6.00: FORCE: horkage modified (noncq)
[   39.129350][   T71] ata2.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   39.130520][   T71] ata2.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   39.131746][   T72] ata3.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   39.132923][   T72] ata3.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   39.134132][   T73] ata4.00: FORCE: horkage modified (noncq)
[   39.135070][   T76] ata7.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   39.136223][   T76] ata7.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   39.137409][   T73] ata4.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   39.138544][   T73] ata4.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   39.140211][   T78] ata9.00: configured for PIO4
[   39.142141][   T72] ata3.00: configured for PIO4
[   39.145403][   T76] ata7.00: configured for PIO4
[   39.147745][   T73] ata4.00: configured for PIO4
[   44.167925][   T75] ata6.00: qc timeout after 5000 msecs (cmd 0x27)
[   44.169168][   T74] ata5.00: qc timeout after 5000 msecs (cmd 0xec)
[   44.170230][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 4
[   44.171572][   T77] ata8.00: qc timeout after 5000 msecs (cmd 0xec)
[   44.172623][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 3
[   44.173950][   T24] ata1.00: qc timeout after 5000 msecs (cmd 0xec)
[   44.174991][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 2
[   44.176321][   T75] ata6.00: failed to read native max address (err_mask=0x4)
[   44.177508][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 0
[   44.178800][   T75] ata6.00: HPA support seems broken, skipping HPA handling
[   44.179983][   T71] ata2.00: qc timeout after 5000 msecs (cmd 0xec)
[   44.181094][   T24] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   44.182214][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 8
[   44.183566][   T74] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   44.184738][   T77] ata8.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   44.185849][   T71] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   44.186954][   T71] ata2.00: revalidation failed (errno=-5)
[   46.384946][   T77] ata8.00: FORCE: horkage modified (noncq)
[   46.386128][   T74] ata5.00: FORCE: horkage modified (noncq)
[   46.387107][   T77] ata8.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   46.388283][   T77] ata8.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   46.389492][   T74] ata5.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   46.390645][   T74] ata5.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   46.392079][   T24] ata1.00: FORCE: horkage modified (noncq)
[   46.393286][   T75] ata6.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   46.394443][   T75] ata6.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   46.397485][   T77] ata8.00: configured for PIO4
[   46.399859][   T74] ata5.00: configured for PIO4
[   46.403393][   T75] ata6.00: configured for PIO4
[   46.404825][   T71] ata2.00: configured for PIO4
[   51.847934][   T24] ata1.00: qc timeout after 5000 msecs (cmd 0x27)
[   51.849426][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 2
[   51.850410][   T24] ata1.00: failed to read native max address (err_mask=0x4)
[   51.851968][   T24] ata1.00: HPA support seems broken, skipping HPA handling
[   54.056972][   T24] ata1.00: ATA-9: HUH721010ALN600, LHGNT290, max UDMA/133
[   54.058186][   T24] ata1.00: 2441609216 sectors, multi 0: LBA48 NCQ (not used)
[   54.067271][   T24] ata1.00: configured for PIO4
[   54.068529][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[   54.078924][   T10] scsi 0:0:0:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.081131][   T10] scsi 0:0:1:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.083217][   T10] scsi 0:0:2:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.085281][   T10] scsi 0:0:3:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.087357][   T10] scsi 0:0:4:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.089442][   T10] scsi 0:0:5:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.091557][   T10] scsi 0:0:6:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.093586][   T10] scsi 0:0:7:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.095707][   T10] scsi 0:0:8:0: Direct-Access     ATA      HUH721010ALN600  T290 PQ: 0 ANSI: 5
[   54.098299][   T10] scsi 0:0:9:0: Enclosure         EMC      ESES Enclosure   0001 PQ: 0 ANSI: 6
[   54.103993][   T10] sas: DONE DISCOVERY on port 0, pid:10, result:0
[   54.105277][   T25] sas: phy1 matched wide port0
[   54.106238][   T25] sas: phy-0:1 added to port-0:0, phy_mask:0x3 (500e004abbbbbb7f)
[   54.107807][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.109834][   T10] sas: ex 500e004abbbbbb7f phy00 change count has changed
[   54.111466][   T10] sas: ex 500e004abbbbbb7f phy00 originated BROADCAST(CHANGE)
[   54.112922][   T10] sas: ex 500e004abbbbbb7f rediscovering phy00
[   54.114867][   T10] sas: ex 500e004abbbbbb7f phy00 broadcast flutter
[   54.116456][   T10] sas: ex 500e004abbbbbb7f phy02 originated BROADCAST(CHANGE)
[   54.118120][   T10] sas: ex 500e004abbbbbb7f rediscovering phy02
[   54.119707][   T10] sas: ex 500e004abbbbbb7f phy02 broadcast flutter
[   54.121385][   T10] sas: ex 500e004abbbbbb7f phy05 originated BROADCAST(CHANGE)
[   54.122823][   T10] sas: ex 500e004abbbbbb7f rediscovering phy05
[   54.124644][   T10] sas: ex 500e004abbbbbb7f phy05 broadcast flutter
[   54.126616][   T10] sas: ex 500e004abbbbbb7f phy08 originated BROADCAST(CHANGE)
[   54.128051][   T10] sas: ex 500e004abbbbbb7f rediscovering phy08
[   54.129686][   T10] sas: ex 500e004abbbbbb7f phy08 broadcast flutter
[   54.131295][   T10] sas: ex 500e004abbbbbb7f phy10 originated BROADCAST(CHANGE)
[   54.132935][   T10] sas: ex 500e004abbbbbb7f rediscovering phy10
[   54.134574][   T10] sas: ex 500e004abbbbbb7f phy10 broadcast flutter
[   54.136690][   T10] sas: ex 500e004abbbbbb7f phy13 originated BROADCAST(CHANGE)
[   54.138314][   T10] sas: ex 500e004abbbbbb7f rediscovering phy13
[   54.140250][   T10] sas: ex 500e004abbbbbb7f phy13 broadcast flutter
[   54.141906][   T10] sas: ex 500e004abbbbbb7f phy15 originated BROADCAST(CHANGE)
[   54.143308][   T10] sas: ex 500e004abbbbbb7f rediscovering phy15
[   54.145141][   T10] sas: ex 500e004abbbbbb7f phy15 broadcast flutter
[   54.146753][   T10] sas: ex 500e004abbbbbb7f phy16 originated BROADCAST(CHANGE)
[   54.148151][   T10] sas: ex 500e004abbbbbb7f rediscovering phy16
[   54.150100][   T10] sas: ex 500e004abbbbbb7f phy16 broadcast flutter
[   54.152025][   T10] sas: ex 500e004abbbbbb7f phy18 originated BROADCAST(CHANGE)
[   54.153740][   T10] sas: ex 500e004abbbbbb7f rediscovering phy18
[   54.155704][   T10] sas: ex 500e004abbbbbb7f phy18 broadcast flutter
[   54.158286][   T10] sas: ex 500e004abbbbbb7f phy23 originated BROADCAST(CHANGE)
[   54.159980][   T10] sas: ex 500e004abbbbbb7f phy23 new device attached
[   54.161780][   T10] sas: ex 500e004abbbbbb7f phy23:U:B attached: ffffffffffffffff (host)
[   54.164840][   T10] sas: ex 500e004abbbbbb7f phy30 originated BROADCAST(CHANGE)
[   54.166217][   T10] sas: ex 500e004abbbbbb7f phy30 new device attached
[   54.167894][   T10] sas: ex 500e004abbbbbb7f phy30:U:B attached: ffffffffffffffff (host)
[   54.171220][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.172923][   T25] sas: broadcast received: 9
[   54.173984][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.175608][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.177034][   T25] sas: broadcast received: 9
[   54.177705][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.178660][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.179693][   T25] sas: broadcast received: 9
[   54.180345][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.181307][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.182327][   T25] sas: broadcast received: 9
[   54.183004][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.184072][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.185134][   T25] sas: broadcast received: 9
[   54.185807][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.186872][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.187927][   T25] sas: broadcast received: 9
[   54.188593][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.189553][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.190589][   T25] sas: broadcast received: 9
[   54.191262][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.192195][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.193183][   T25] sas: broadcast received: 9
[   54.193810][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.194774][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.195785][   T25] sas: phy-0:2 added to port-0:1, phy_mask:0x4 (5000cca09e0418f1)
[   54.196879][   T10] sas: DOING DISCOVERY on port 1, pid:10
[   54.197651][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x1
[   54.198991][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x0 device_id 16396
[   54.252354][   T10] scsi 0:0:10:0: Direct-Access     HITACHI  H4SMR324 CLAR400 S116 PQ: 0 ANSI: 6
[   54.253745][    C0] scsi 0:0:10:0: Power-on or device reset occurred
[   54.256816][   T10] sas: DONE DISCOVERY on port 1, pid:10, result:0
[   54.257739][   T25] sas: phy3 matched wide port0
[   54.258416][   T25] sas: phy-0:3 added to port-0:0, phy_mask:0xb (500e004abbbbbb7f)
[   54.259517][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.268530][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[   54.269405][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.270419][   T25] sas: broadcast received: 9
[   54.271073][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[   54.279449][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[   54.280819][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[   54.282467][   T25] sas: phy-0:4 added to port-0:2, phy_mask:0x10 (500e004abbbbbb7f)
[   54.284241][   T10] sas: DOING DISCOVERY on port 2, pid:10
[   54.285554][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.287724][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x0 device_id 16641
[   54.290695][   T10] sas: ex 500e004abbbbbb7f phy00:D:0 attached: 0000000000000000 (no device)
[   54.293100][   T10] sas: ex 500e004abbbbbb7f phy01:U:A attached: 500e004abbbbbb01 (stp)
[   54.295043][   T10] sas: ex 500e004abbbbbb7f phy02:D:0 attached: 0000000000000000 (no device)
[   54.297285][   T10] sas: ex 500e004abbbbbb7f phy03:U:A attached: 500e004abbbbbb03 (stp)
[   54.299573][   T10] sas: ex 500e004abbbbbb7f phy04:U:1 attached: 0000000000000000 (no device)
[   54.301593][   T10] sas: ex 500e004abbbbbb7f phy05:D:0 attached: 0000000000000000 (no device)
[   54.303998][   T10] sas: ex 500e004abbbbbb7f phy06:U:1 attached: 0000000000000000 (no device)
[   54.306089][   T10] sas: ex 500e004abbbbbb7f phy07:D:0 attached: 0000000000000000 (no device)
[   54.308129][   T10] sas: ex 500e004abbbbbb7f phy08:D:0 attached: 0000000000000000 (no device)
[   54.310393][   T10] sas: ex 500e004abbbbbb7f phy09:U:A attached: 500e004abbbbbb09 (stp)
[   54.312326][   T10] sas: ex 500e004abbbbbb7f phy10:D:0 attached: 0000000000000000 (no device)
[   54.314738][   T10] sas: ex 500e004abbbbbb7f phy11:U:A attached: 500e004abbbbbb0b (stp)
[   54.316929][   T10] sas: ex 500e004abbbbbb7f phy12:U:A attached: 500e004abbbbbb0c (stp)
[   54.318914][   T10] sas: ex 500e004abbbbbb7f phy13:D:0 attached: 0000000000000000 (no device)
[   54.321151][   T10] sas: ex 500e004abbbbbb7f phy14:U:A attached: 500e004abbbbbb0e (stp)
[   54.323098][   T10] sas: ex 500e004abbbbbb7f phy15:D:0 attached: 0000000000000000 (no device)
[   54.325178][   T10] sas: ex 500e004abbbbbb7f phy16:D:0 attached: 0000000000000000 (no device)
[   54.327662][   T10] sas: ex 500e004abbbbbb7f phy17:U:A attached: 500e004abbbbbb11 (stp)
[   54.329600][   T10] sas: ex 500e004abbbbbb7f phy18:D:0 attached: 0000000000000000 (no device)
[   54.331884][   T10] sas: ex 500e004abbbbbb7f phy19:U:A attached: 500e004abbbbbb13 (stp)
[   54.334051][   T10] sas: ex 500e004abbbbbb7f phy20:U:B attached: ffffffffffffffff (host)
[   54.336413][   T10] sas: ex 500e004abbbbbb7f phy21:U:B attached: ffffffffffffffff (host)
[   54.338415][   T10] sas: ex 500e004abbbbbb7f phy22:D:0 attached: 0000000000000000 (no device)
[   54.340488][   T10] sas: ex 500e004abbbbbb7f phy23:D:0 attached: 0000000000000000 (no device)
[   54.342985][   T10] sas: ex 500e004abbbbbb7f phy24:U:1 attached: 0000000000000000 (no device)
[   54.345275][   T10] sas: ex 500e004abbbbbb7f phy25:U:1 attached: 0000000000000000 (no device)
[   54.347353][   T10] sas: ex 500e004abbbbbb7f phy26:D:0 attached: 0000000000000000 (no device)
[   54.349433][   T10] sas: ex 500e004abbbbbb7f phy27:D:0 attached: 0000000000000000 (no device)
[   54.351915][   T10] sas: ex 500e004abbbbbb7f phy28:U:1 attached: 0000000000000000 (no device)
[   54.354254][   T10] sas: ex 500e004abbbbbb7f phy29:U:B attached: ffffffffffffffff (host)
[   54.356234][   T10] sas: ex 500e004abbbbbb7f phy30:D:0 attached: 0000000000000000 (no device)
[   54.358324][   T10] sas: ex 500e004abbbbbb7f phy31:D:0 attached: 0000000000000000 (no device)
[   54.360875][   T10] sas: ex 500e004abbbbbb7f phy32:U:1 attached: 0000000000000000 (no device)
[   54.363293][   T10] sas: ex 500e004abbbbbb7f phy33:U:1 attached: 0000000000000000 (no device)
[   54.365372][   T10] sas: ex 500e004abbbbbb7f phy34:D:0 attached: 0000000000000000 (no device)
[   54.367453][   T10] sas: ex 500e004abbbbbb7f phy35:D:0 attached: 0000000000000000 (no device)
[   54.369578][   T10] sas: ex 500e004abbbbbb7f phy36:D:B attached: 500e004abbbbbb7e (host+target)
[   54.371865][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.373989][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x1 device_id 16642
[   54.376420][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.378530][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x3 device_id 16643
[   54.380912][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.382893][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x9 device_id 16644
[   54.384466][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.385813][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0xb device_id 16645
[   54.387333][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.388648][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0xc device_id 16646
[   54.390175][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.391479][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0xe device_id 16647
[   54.393042][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.394360][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x11 device_id 16648
[   54.395941][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.397262][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x13 device_id 16649
[   54.398255][   T10] sas: target proto 0x0 at 500e004abbbbbb7f:0x14 not handled
[   54.399703][   T10] sas: ex 500e004abbbbbb7f phy20 failed to discover
[   54.400626][   T10] sas: target proto 0x0 at 500e004abbbbbb7f:0x15 not handled
[   54.401630][   T10] sas: ex 500e004abbbbbb7f phy21 failed to discover
[   54.402547][   T10] sas: target proto 0x0 at 500e004abbbbbb7f:0x1d not handled
[   54.403576][   T10] sas: ex 500e004abbbbbb7f phy29 failed to discover
[   54.404508][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x2
[   54.405851][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x24 device_id 16650
[   54.458930][   T65] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[   54.460182][   T24] sas: ata1: end_device-0:0:0: dev error handler
[   54.461080][   T24] sas: ata2: end_device-0:0:2: dev error handler
[   54.461978][   T24] sas: ata3: end_device-0:0:5: dev error handler
[   54.462875][   T71] sas: ata4: end_device-0:0:8: dev error handler
[   54.463759][   T71] sas: ata5: end_device-0:0:10: dev error handler
[   54.464665][   T75] sas: ata6: end_device-0:0:13: dev error handler
[   54.465557][   T75] sas: ata7: end_device-0:0:15: dev error handler
[   54.466463][   T74] sas: ata8: end_device-0:0:16: dev error handler
[   54.467365][   T74] sas: ata9: end_device-0:0:18: dev error handler
[   54.468263][   T77] sas: ata10: end_device-0:1:1: dev error handler
[   54.469175][   T73] sas: ata11: end_device-0:1:3: dev error handler
[   54.470119][   T76] sas: ata12: end_device-0:1:9: dev error handler
[   54.471013][   T72] sas: ata13: end_device-0:1:11: dev error handler
[   54.471962][   T78] sas: ata14: end_device-0:1:12: dev error handler
[   54.472915][   T80] sas: ata15: end_device-0:1:14: dev error handler
[   54.473899][   T71] sas: ata16: end_device-0:1:17: dev error handler
[   54.474836][   T75] sas: ata17: end_device-0:1:19: dev error handler
[   62.087971][   T77] ata10.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.089089][   T78] ata14.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.090168][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 2
[   62.091524][   T73] ata11.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.092590][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 3
[   62.093942][   T72] ata13.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.095234][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 1
[   62.096815][   T80] ata15.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.098066][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 4
[   62.099630][   T76] ata12.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.100888][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 0
[   62.102448][   T77] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.103781][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 5
[   62.105311][   T71] ata16.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.106586][   T75] ata17.00: qc timeout after 5000 msecs (cmd 0xec)
[   62.107895][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 6
[   62.109424][   T73] ata11.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.110755][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 7
[   62.112252][   T78] ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.113547][   T80] ata15.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.114860][   T76] ata12.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.116233][   T72] ata13.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.117531][   T71] ata16.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   62.118850][   T75] ata17.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.375935][   T78] ata14.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.377554][   T77] ata10.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.378838][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 0
[   74.380421][   T80] ata15.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.381686][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 1
[   74.383243][   T72] ata13.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.384503][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 2
[   74.386064][   T76] ata12.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.387326][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 3
[   74.388900][   T71] ata16.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.390167][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 4
[   74.391705][   T73] ata11.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.392945][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 5
[   74.394470][   T78] ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.395796][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 6
[   74.397298][   T75] ata17.00: qc timeout after 10000 msecs (cmd 0xec)
[   74.398581][   T77] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.399913][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 7
[   74.401394][   T80] ata15.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.402694][   T72] ata13.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.404055][   T71] ata16.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.405348][   T76] ata12.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.406647][   T75] ata17.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   74.407941][   T73] ata11.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.631936][   T80] ata15.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.633520][   T78] ata14.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.634818][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 0
[  106.636396][   T72] ata13.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.637668][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 1
[  106.639237][   T71] ata16.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.640503][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 2
[  106.642071][   T76] ata12.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.643338][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 3
[  106.644907][   T75] ata17.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.646173][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 4
[  106.647716][   T73] ata11.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.648947][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 5
[  106.650466][   T77] ata10.00: qc timeout after 30000 msecs (cmd 0xec)
[  106.651711][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 6
[  106.653233][   T80] ata15.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.654553][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 7
[  106.656070][   T72] ata13.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.657392][   T78] ata14.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.658702][   T71] ata16.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.660006][   T76] ata12.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.661309][   T75] ata17.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.662604][   T73] ata11.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  106.663908][   T77] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  108.843007][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[  108.853113][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb01 returned -19
[  108.854815][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16642
[  108.856602][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb03 returned -19
[  108.858278][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16643
[  108.859993][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb09 returned -19
[  108.861633][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16644
[  108.863340][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb0b returned -19
[  108.864980][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16645
[  108.866704][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb0c returned -19
[  108.868345][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16646
[  108.870030][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb0e returned -19
[  108.871640][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16647
[  108.873314][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb11 returned -19
[  108.874936][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16648
[  108.876626][   T10] sas: sas_probe_sata: for exp-attached device 500e004abbbbbb13 returned -19
[  108.878253][   T10] pm80xx0:: pm8001_chip_dereg_dev_req 4283: unregister device device_id 16649
[  108.880372][    C0] pm80xx0:: mpi_ssp_event 2097: sas IO status 0x60
[  108.881362][    C0] pm80xx0:: mpi_ssp_event 2102: port_id:0x2, tag:0x2ad, event:0x60
[  108.891101][    C0] pm80xx0:: mpi_ssp_event 2097: sas IO status 0x60
[  108.892078][    C0] pm80xx0:: mpi_ssp_event 2102: port_id:0x2, tag:0x2ad, event:0x60
[  108.902190][    C0] pm80xx0:: mpi_ssp_event 2097: sas IO status 0x60
[  108.903168][    C0] pm80xx0:: mpi_ssp_event 2102: port_id:0x2, tag:0x2ad, event:0x60
[  108.913146][    C0] pm80xx0:: mpi_ssp_event 2097: sas IO status 0x60
[  108.914124][    C0] pm80xx0:: mpi_ssp_event 2102: port_id:0x2, tag:0x2ad, event:0x60
[  108.914124][   T10] sas: DONE DISCOVERY on port 2, pid:10, result:0
[  108.917210][   T25] sas: phy-0:5 added to port-0:3, phy_mask:0x20 (5000cca09e03bdfd)
[  108.918625][   T10] sas: DOING DISCOVERY on port 3, pid:10
[  108.919624][   T10] pm80xx0:: pm80xx_chip_reg_dev_req 4770: register device req phy_id 0x0 port_id 0x3
[  108.921328][    C0] pm80xx0:: pm8001_mpi_reg_resp 3367: register device status 0 phy_id 0x0 device_id 16651
[  108.975455][   T10] scsi 0:0:12:0: Direct-Access     HITACHI  H4SMR324 CLAR400 S116 PQ: 0 ANSI: 6
[  108.977231][    C0] scsi 0:0:12:0: Power-on or device reset occurred
[  108.980647][   T10] sas: DONE DISCOVERY on port 3, pid:10, result:0
[  108.981835][   T25] sas: phy6 matched wide port2
[  108.982715][   T25] sas: phy-0:6 added to port-0:2, phy_mask:0x50 (500e004abbbbbb7f)
[  108.984149][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  108.986212][   T10] sas: ex 500e004abbbbbb7f phy01 change count has changed
[  108.987788][   T10] sas: ex 500e004abbbbbb7f phy01 originated BROADCAST(CHANGE)
[  108.989127][   T10] sas: ex 500e004abbbbbb7f rediscovering phy01
[  108.990622][   T10] sas: ex 500e004abbbbbb7f phy01 broadcast flutter
[  108.992096][   T10] sas: ex 500e004abbbbbb7f phy03 originated BROADCAST(CHANGE)
[  108.993435][   T10] sas: ex 500e004abbbbbb7f rediscovering phy03
[  108.995140][   T10] sas: ex 500e004abbbbbb7f phy03 broadcast flutter
[  108.997424][   T10] sas: ex 500e004abbbbbb7f phy09 originated BROADCAST(CHANGE)
[  108.998760][   T10] sas: ex 500e004abbbbbb7f rediscovering phy09
[  109.000308][   T10] sas: ex 500e004abbbbbb7f phy09 broadcast flutter
[  109.001828][   T10] sas: ex 500e004abbbbbb7f phy11 originated BROADCAST(CHANGE)
[  109.003161][   T10] sas: ex 500e004abbbbbb7f rediscovering phy11
[  109.004797][   T10] sas: ex 500e004abbbbbb7f phy11 broadcast flutter
[  109.006386][   T10] sas: ex 500e004abbbbbb7f phy12 originated BROADCAST(CHANGE)
[  109.007708][   T10] sas: ex 500e004abbbbbb7f rediscovering phy12
[  109.009468][   T10] sas: ex 500e004abbbbbb7f phy12 broadcast flutter
[  109.010997][   T10] sas: ex 500e004abbbbbb7f phy14 originated BROADCAST(CHANGE)
[  109.012316][   T10] sas: ex 500e004abbbbbb7f rediscovering phy14
[  109.013994][   T10] sas: ex 500e004abbbbbb7f phy14 broadcast flutter
[  109.015708][   T10] sas: ex 500e004abbbbbb7f phy17 originated BROADCAST(CHANGE)
[  109.017029][   T10] sas: ex 500e004abbbbbb7f rediscovering phy17
[  109.018896][   T10] sas: ex 500e004abbbbbb7f phy17 broadcast flutter
[  109.020657][   T10] sas: ex 500e004abbbbbb7f phy19 originated BROADCAST(CHANGE)
[  109.021971][   T10] sas: ex 500e004abbbbbb7f rediscovering phy19
[  109.023701][   T10] sas: ex 500e004abbbbbb7f phy19 broadcast flutter
[  109.028563][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.029829][   T25] sas: phy7 matched wide port2
[  109.030662][   T25] sas: phy-0:7 added to port-0:2, phy_mask:0xd0 (500e004abbbbbb7f)
[  109.032043][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.041227][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.042558][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.043862][    T1] mpt3sas version 43.100.00.00 loaded
[  109.044836][   T25] sas: broadcast received: 9
[  109.045754][    T1] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[  109.046887][    T1] scsi 0:0:1:0: Attached scsi generic sg1 type 0
[  109.048013][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.049161][   T77] sd 0:0:0:0: [sda] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.050455][   T77] sd 0:0:0:0: [sda] Write Protect is off
[  109.051264][   T77] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  109.052125][   T77] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.053566][   T77] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[  109.054996][   T73] sd 0:0:1:0: [sdb] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.056253][   T73] sd 0:0:1:0: [sdb] Write Protect is off
[  109.057064][   T73] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[  109.057923][   T73] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.059357][   T73] sd 0:0:1:0: [sdb] Preferred minimum I/O size 4096 bytes
[  109.060765][   T80] sd 0:0:2:0: [sdc] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.062006][   T80] sd 0:0:2:0: [sdc] Write Protect is off
[  109.062793][   T80] sd 0:0:2:0: [sdc] Mode Sense: 00 3a 00 00
[  109.063621][   T80] sd 0:0:2:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.065068][   T80] sd 0:0:2:0: [sdc] Preferred minimum I/O size 4096 bytes
[  109.066430][   T71] sd 0:0:3:0: [sdd] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.067671][   T71] sd 0:0:3:0: [sdd] Write Protect is off
[  109.068476][   T71] sd 0:0:3:0: [sdd] Mode Sense: 00 3a 00 00
[  109.069305][   T71] sd 0:0:3:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.070745][   T71] sd 0:0:3:0: [sdd] Preferred minimum I/O size 4096 bytes
[  109.072125][   T72] sd 0:0:4:0: [sde] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.073373][   T72] sd 0:0:4:0: [sde] Write Protect is off
[  109.074174][   T72] sd 0:0:4:0: [sde] Mode Sense: 00 3a 00 00
[  109.075026][   T72] sd 0:0:4:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.076445][   T72] sd 0:0:4:0: [sde] Preferred minimum I/O size 4096 bytes
[  109.077823][   T76] sd 0:0:5:0: [sdf] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.079083][   T76] sd 0:0:5:0: [sdf] Write Protect is off
[  109.079897][   T76] sd 0:0:5:0: [sdf] Mode Sense: 00 3a 00 00
[  109.080738][   T76] sd 0:0:5:0: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.082144][   T76] sd 0:0:5:0: [sdf] Preferred minimum I/O size 4096 bytes
[  109.083490][   T75] sd 0:0:6:0: [sdg] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.084718][   T75] sd 0:0:6:0: [sdg] Write Protect is off
[  109.085527][   T75] sd 0:0:6:0: [sdg] Mode Sense: 00 3a 00 00
[  109.086366][   T75] sd 0:0:6:0: [sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.087770][   T75] sd 0:0:6:0: [sdg] Preferred minimum I/O size 4096 bytes
[  109.089126][   T78] sd 0:0:7:0: [sdh] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.090368][   T78] sd 0:0:7:0: [sdh] Write Protect is off
[  109.091162][   T78] sd 0:0:7:0: [sdh] Mode Sense: 00 3a 00 00
[  109.092001][   T78] sd 0:0:7:0: [sdh] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.093395][   T78] sd 0:0:7:0: [sdh] Preferred minimum I/O size 4096 bytes
[  109.094760][   T81] sd 0:0:8:0: [sdi] 2441609216 4096-byte logical blocks: (10.0 TB/9.10 TiB)
[  109.095973][   T81] sd 0:0:8:0: [sdi] Write Protect is off
[  109.096765][   T81] sd 0:0:8:0: [sdi] Mode Sense: 00 3a 00 00
[  109.097586][   T81] sd 0:0:8:0: [sdi] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  109.099020][   T81] sd 0:0:8:0: [sdi] Preferred minimum I/O size 4096 bytes
[  109.100568][    T1] sd 0:0:2:0: Attached scsi generic sg2 type 0
[  109.101502][   T24] sd 0:0:12:0: [sdk] 781250000 512-byte logical blocks: (400 GB/373 GiB)
[  109.102693][   T24] sd 0:0:12:0: [sdk] 4096-byte physical blocks
[  109.103560][   T79] sd 0:0:10:0: [sdj] 781250000 512-byte logical blocks: (400 GB/373 GiB)
[  109.104778][   T79] sd 0:0:10:0: [sdj] 4096-byte physical blocks
[  109.105656][   T24] sd 0:0:12:0: [sdk] Write Protect is off
[  109.106476][   T24] sd 0:0:12:0: [sdk] Mode Sense: b7 00 10 08
[  109.107462][   T79] sd 0:0:10:0: [sdj] Write Protect is off
[  109.108459][   T79] sd 0:0:10:0: [sdj] Mode Sense: b7 00 10 08
[  109.109510][    T1] sd 0:0:3:0: Attached scsi generic sg3 type 0
[  109.110638][    T1] sd 0:0:4:0: Attached scsi generic sg4 type 0
[  109.111753][   T24] sd 0:0:12:0: [sdk] Write cache: disabled, read cache: enabled, supports DPO and FUA
[  109.113409][   T79] sd 0:0:10:0: [sdj] Write cache: disabled, read cache: enabled, supports DPO and FUA
[  109.116530][    T1] sd 0:0:5:0: Attached scsi generic sg5 type 0
[  109.117690][    T1] sd 0:0:6:0: Attached scsi generic sg6 type 0
[  109.118720][    T1] sd 0:0:7:0: Attached scsi generic sg7 type 0
[  109.119648][   T24] sd 0:0:12:0: [sdk] Preferred minimum I/O size 4096 bytes
[  109.120997][   T79] sd 0:0:10:0: [sdj] Preferred minimum I/O size 4096 bytes
[  109.122605][    T1] sd 0:0:8:0: Attached scsi generic sg8 type 0
[  109.123589][    T1] scsi 0:0:9:0: Attached scsi generic sg9 type 13
[  109.124590][    T1] sd 0:0:10:0: Attached scsi generic sg10 type 0
[  109.125574][    T1] sd 0:0:12:0: Attached scsi generic sg11 type 0
[  109.126519][    T1] SCSI Media Changer driver v0.25 
[  109.129178][   T79]  sdj: sdj1 sdj2
[  109.129866][   T79] sd 0:0:10:0: [sdj] Attached SCSI disk
[  109.130692][   T24]  sdk: sdk1 sdk2
[  109.131305][   T24] sd 0:0:12:0: [sdk] Attached SCSI disk
[  109.133327][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.134186][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.135216][   T25] sas: broadcast received: 9
[  109.135878][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.144861][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.145711][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.146733][   T25] sas: broadcast received: 9
[  109.147386][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.155698][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.156565][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.157603][   T25] sas: broadcast received: 9
[  109.158258][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.167272][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.168291][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.169311][   T25] sas: broadcast received: 9
[  109.169960][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.178822][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.179807][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.180822][   T25] sas: broadcast received: 9
[  109.181476][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.189960][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.190834][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.191863][   T25] sas: broadcast received: 9
[  109.192512][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.200818][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.201686][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.202705][   T25] sas: broadcast received: 9
[  109.203356][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.211659][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.212523][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.213559][   T25] sas: broadcast received: 9
[  109.214213][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.222569][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.223440][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.224456][   T25] sas: broadcast received: 9
[  109.225115][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.233261][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.234121][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.235139][   T25] sas: broadcast received: 9
[  109.235782][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.243772][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.244633][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.245651][   T25] sas: broadcast received: 9
[  109.246307][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.254862][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.255724][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.256738][   T25] sas: broadcast received: 9
[  109.257389][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.265425][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.266286][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.267308][   T25] sas: broadcast received: 9
[  109.267970][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.277630][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.278625][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.279650][   T25] sas: broadcast received: 9
[  109.280309][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.289937][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.290871][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.291894][   T25] sas: broadcast received: 9
[  109.292544][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.301072][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.301941][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.302964][   T25] sas: broadcast received: 9
[  109.303609][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.311568][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.312419][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.313436][   T25] sas: broadcast received: 9
[  109.314101][   T10] sas: REVALIDATING DOMAIN on port 0, pid:10
[  109.322062][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.322928][   T10] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[  109.323940][   T25] sas: broadcast received: 9
[  109.324586][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.332809][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.333690][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.334711][   T25] sas: broadcast received: 9
[  109.335361][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.344428][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.345299][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.346308][   T25] sas: broadcast received: 9
[  109.346960][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.355913][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.356789][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.357805][   T25] sas: broadcast received: 9
[  109.358453][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.367739][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.368607][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.369626][   T25] sas: broadcast received: 9
[  109.370292][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.379101][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.379965][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.380991][   T25] sas: broadcast received: 9
[  109.381633][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.390770][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.391631][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.392647][   T25] sas: broadcast received: 9
[  109.393305][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.402379][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.403730][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.405321][   T25] sas: broadcast received: 9
[  109.406343][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.414819][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.416449][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.418031][   T25] sas: broadcast received: 9
[  109.419040][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.427452][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.428810][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.430375][   T25] sas: broadcast received: 9
[  109.431395][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.439761][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.441102][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.442690][   T25] sas: broadcast received: 9
[  109.443714][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.452156][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.453501][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.455082][   T25] sas: broadcast received: 9
[  109.456091][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.465090][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.466439][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.468033][   T25] sas: broadcast received: 9
[  109.469048][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.478232][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.479596][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.481177][   T25] sas: broadcast received: 9
[  109.482180][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.490569][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.491915][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.493500][   T25] sas: broadcast received: 9
[  109.494509][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.503337][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.504704][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.506270][   T25] sas: broadcast received: 9
[  109.507279][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.516003][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.517354][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.518939][   T25] sas: broadcast received: 9
[  109.519951][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.528614][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.529972][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.531559][   T25] sas: broadcast received: 9
[  109.532563][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.541516][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.542868][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.544451][   T25] sas: broadcast received: 9
[  109.545477][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.553953][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.555297][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.556873][   T25] sas: broadcast received: 9
[  109.557890][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.566376][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.567724][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.569299][   T25] sas: broadcast received: 9
[  109.570315][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.578768][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.580126][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.581706][   T25] sas: broadcast received: 9
[  109.582731][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.592467][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.593820][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.595408][   T25] sas: broadcast received: 9
[  109.596413][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.605649][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.606883][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.607634][   T25] sas: broadcast received: 9
[  109.608400][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.616863][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.617912][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.619134][   T25] sas: broadcast received: 9
[  109.619922][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.628686][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.629742][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.630970][   T25] sas: broadcast received: 9
[  109.631749][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.639984][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.641033][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.642251][   T25] sas: broadcast received: 9
[  109.643030][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.651410][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.652460][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.653686][   T25] sas: broadcast received: 9
[  109.654462][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.663780][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.664826][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.666045][   T25] sas: broadcast received: 9
[  109.666822][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.676578][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.677929][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.679152][   T25] sas: broadcast received: 9
[  109.679956][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.688892][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.689938][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.691159][   T25] sas: broadcast received: 9
[  109.691940][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.700716][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.701765][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.702986][   T25] sas: broadcast received: 9
[  109.703762][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.711776][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.712825][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.714050][   T25] sas: broadcast received: 9
[  109.714831][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.723372][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.724420][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.725638][   T25] sas: broadcast received: 9
[  109.726418][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.734549][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.735597][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.736831][   T25] sas: broadcast received: 9
[  109.737604][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.746299][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.747348][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.748569][   T25] sas: broadcast received: 9
[  109.749353][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.758272][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.759319][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.760541][   T25] sas: broadcast received: 9
[  109.761330][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.769992][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.771046][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.772267][   T25] sas: broadcast received: 9
[  109.773049][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.781659][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.782992][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.784213][   T25] sas: broadcast received: 9
[  109.784997][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.794342][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.795389][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.796608][   T25] sas: broadcast received: 9
[  109.797389][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.805872][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.806921][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.808144][   T25] sas: broadcast received: 9
[  109.808928][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.817962][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.819015][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.820241][   T25] sas: broadcast received: 9
[  109.821022][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.829411][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.830456][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.831681][   T25] sas: broadcast received: 9
[  109.832458][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.841430][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.842474][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.843693][   T25] sas: broadcast received: 9
[  109.844467][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.853888][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.854937][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.856162][   T25] sas: broadcast received: 9
[  109.856943][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.866054][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.867361][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.868683][   T25] sas: broadcast received: 9
[  109.869694][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.878132][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.879485][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.881056][   T25] sas: broadcast received: 9
[  109.882068][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.890420][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.891765][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.893351][   T25] sas: broadcast received: 9
[  109.894367][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.902772][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.904115][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.905700][   T25] sas: broadcast received: 9
[  109.906717][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.915141][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.916504][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.918071][   T25] sas: broadcast received: 9
[  109.919081][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.927419][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.928779][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.930368][   T25] sas: broadcast received: 9
[  109.931377][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.939762][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.941105][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.942694][   T25] sas: broadcast received: 9
[  109.943705][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.952260][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.953597][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.955186][   T25] sas: broadcast received: 9
[  109.956180][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.965009][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.966363][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.967940][   T25] sas: broadcast received: 9
[  109.968954][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.977679][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.978934][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.979955][   T25] sas: broadcast received: 9
[  109.980597][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  109.989215][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  109.990096][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  109.991119][   T25] sas: broadcast received: 9
[  109.991781][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.001188][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.002346][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.003372][   T25] sas: broadcast received: 9
[  110.004031][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.013052][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.013930][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.014950][   T25] sas: broadcast received: 9
[  110.015591][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.024936][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.026289][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.027883][   T25] sas: broadcast received: 9
[  110.028897][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.037704][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.039041][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.040616][   T25] sas: broadcast received: 9
[  110.041624][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.050124][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.051468][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.053047][   T25] sas: broadcast received: 9
[  110.054049][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.062438][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.063773][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.065339][   T25] sas: broadcast received: 9
[  110.066344][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.074774][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.076118][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.077703][   T25] sas: broadcast received: 9
[  110.078727][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.087124][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.088470][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.090047][   T25] sas: broadcast received: 9
[  110.091055][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.099434][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.100771][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.102339][   T25] sas: broadcast received: 9
[  110.103344][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.111811][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.113150][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.114732][   T25] sas: broadcast received: 9
[  110.115753][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.124601][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.125956][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.127541][   T25] sas: broadcast received: 9
[  110.128351][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.137755][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.138801][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.140019][   T25] sas: broadcast received: 9
[  110.140793][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.149146][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.150192][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.151410][   T25] sas: broadcast received: 9
[  110.152191][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.161780][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.162826][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.164046][   T25] sas: broadcast received: 9
[  110.164821][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.173565][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.174606][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.175825][   T25] sas: broadcast received: 9
[  110.176599][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.184698][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.185748][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.187063][   T25] sas: broadcast received: 9
[  110.188084][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.196435][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.197797][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.199366][   T25] sas: broadcast received: 9
[  110.200369][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.208760][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.210102][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.211687][   T25] sas: broadcast received: 9
[  110.212711][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.221201][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.222551][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.224127][   T25] sas: broadcast received: 9
[  110.225148][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.233785][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.235124][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.236720][   T25] sas: broadcast received: 9
[  110.237734][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.246152][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.247489][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.249058][   T25] sas: broadcast received: 9
[  110.250077][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.258486][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.259834][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.261424][   T25] sas: broadcast received: 9
[  110.262440][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.271140][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.272481][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.274076][   T25] sas: broadcast received: 9
[  110.275085][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.283926][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.285277][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.286865][   T25] sas: broadcast received: 9
[  110.287870][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.296710][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.298064][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.299654][   T25] sas: broadcast received: 9
[  110.300679][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.309326][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.310683][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.312264][   T25] sas: broadcast received: 9
[  110.313277][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.321799][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.323145][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.324723][   T25] sas: broadcast received: 9
[  110.325734][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.334157][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.335514][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  110.337097][   T25] sas: broadcast received: 9
[  110.338106][   T10] sas: REVALIDATING DOMAIN on port 2, pid:10
[  110.346567][   T10] sas: ex 500e004abbbbbb7f phys DID NOT change
[  110.347923][   T10] sas: done REVALIDATING DOMAIN on port 2, pid:10, res 0x0
[  118.821706][   T80]  sdc: sdc1 sdc2
[  118.822709][   T80] sd 0:0:2:0: [sdc] Attached SCSI disk
[  118.858590][   T76]  sdf: sdf1 sdf2 sdf3 sdf4
[  118.860053][   T76] sd 0:0:5:0: [sdf] Attached SCSI disk
[  118.905811][   T72]  sde: sde1 sde2
[  118.906883][   T72] sd 0:0:4:0: [sde] Attached SCSI disk
[  118.914486][   T81]  sdi: sdi1 sdi2 sdi3 sdi4 sdi5 sdi6 sdi7 sdi8 sdi9 sdi10
[  118.916301][   T81] sd 0:0:8:0: [sdi] Attached SCSI disk
[  118.920188][   T78]  sdh: sdh1 sdh2 sdh3 sdh4
[  118.921245][   T78] sd 0:0:7:0: [sdh] Attached SCSI disk
[  118.951298][   T77]  sda: sda1 sda2 sda3 sda4
[  118.952626][   T77] sd 0:0:0:0: [sda] Attached SCSI disk
[  118.977082][   T71]  sdd: sdd1 sdd2
[  118.978139][   T71] sd 0:0:3:0: [sdd] Attached SCSI disk
[  119.047424][   T75]  sdg: sdg1 sdg2 sdg3 sdg4
[  119.048750][   T75] sd 0:0:6:0: [sdg] Attached SCSI disk
[  119.058720][   T73]  sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11
[  119.061031][   T73] sd 0:0:1:0: [sdb] Attached SCSI disk
[  119.064025][    T1] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  119.065940][    T1] scsi host1: scsi_debug: version 0191 [20210520]
[  119.065940][    T1]   dev_size_mb=8, opts=0x0, submit_queues=1, statistics=0
[  119.068609][    T1] scsi 1:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  119.070278][    T1] scsi 1:0:0:0: Power-on or device reset occurred
[  119.074671][    T1] sd 1:0:0:0: Attached scsi generic sg12 type 0
[  119.076204][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[  119.077790][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[  119.079815][    T1] tun: Universal TUN/TAP device driver, 1.6
[  119.080906][   T73] sd 1:0:0:0: [sdl] 16384 512-byte logical blocks: (8.39 MB/8.00 MiB)
[  119.082495][    T1] e1000: Intel(R) PRO/1000 Network Driver
[  119.083549][    T1] e1000: Copyright (c) 1999-2006 Intel Corporation.
[  119.097451][    T1] ACPI: \_SB_.LNKC: Enabled at IRQ 10
[  119.099000][   T73] sd 1:0:0:0: [sdl] Write Protect is off
[  119.100003][   T73] sd 1:0:0:0: [sdl] Mode Sense: 73 00 10 08
[  119.103073][   T73] sd 1:0:0:0: [sdl] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  119.107813][   T73] sd 1:0:0:0: [sdl] Preferred minimum I/O size 512 bytes
[  119.109002][   T73] sd 1:0:0:0: [sdl] Optimal transfer size 524288 bytes
[  119.129562][   T73] sd 1:0:0:0: [sdl] Attached SCSI disk
[  119.408866][    T1] e1000 0000:00:03.0 eth0: (PCI:33MHz:32-bit) 52:54:00:12:34:56
[  119.410564][    T1] e1000 0000:00:03.0 eth0: Intel(R) PRO/1000 Network Connection
[  119.412269][    T1] e1000e: Intel(R) PRO/1000 Network Driver
[  119.413532][    T1] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[  119.415030][    T1] igb: Intel(R) Gigabit Ethernet Network Driver
[  119.416413][    T1] igb: Copyright (c) 2007-2014 Intel Corporation.
[  119.417840][    T1] Intel(R) 2.5G Ethernet Linux Driver
[  119.418827][    T1] Copyright(c) 2018 Intel Corporation.
[  119.419828][    T1] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[  119.421084][    T1] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[  119.422332][    T1] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver
[  119.423886][    T1] ixgbevf: Copyright (c) 2009 - 2018 Intel Corporation.
[  119.425174][    T1] i40e: Intel(R) Ethernet Connection XL710 Network Driver
[  119.426468][    T1] i40e: Copyright (c) 2013 - 2019 Intel Corporation.
[  119.427769][    T1] usbcore: registered new interface driver cdc_ether
[  119.429097][    T1] usbcore: registered new interface driver r8153_ecm
[  119.430591][    T1] Fusion MPT base driver 3.04.20
[  119.431728][    T1] Copyright (c) 1999-2008 LSI Corporation
[  119.433014][    T1] Fusion MPT SPI Host driver 3.04.20
[  119.434203][    T1] Fusion MPT SAS Host driver 3.04.20
[  119.435403][    T1] Fusion MPT misc device (ioctl) driver 3.04.20
[  119.436867][    T1] mptctl: Registered with Fusion MPT base driver
[  119.438257][    T1] mptctl: /dev/mptctl @ (major,minor=10,220)
[  119.439664][    T1] VFIO - User Level meta-driver version: 0.3
[  119.441073][    T1] usbcore: registered new interface driver usb-storage
[  119.442607][    T1] usbcore: registered new interface driver ark3116
[  119.444047][    T1] usbserial: USB Serial support registered for ark3116
[  119.445541][    T1] usbcore: registered new interface driver ftdi_sio
[  119.447014][    T1] usbserial: USB Serial support registered for FTDI USB Serial Device
[  119.448719][    T1] usbcore: registered new interface driver pl2303
[  119.450042][    T1] usbserial: USB Serial support registered for pl2303
[  119.451630][    T1] vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
[  119.453167][    T1] vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 1
[  119.454914][    T1] vhci_hcd: created sysfs vhci_hcd.0
[  119.455779][    T1] hub 1-0:1.0: USB hub found
[  119.456440][    T1] hub 1-0:1.0: 8 ports detected
[  119.457212][    T1] vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
[  119.458168][    T1] vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 2
[  119.459328][    T1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[  119.460649][    T1] hub 2-0:1.0: USB hub found
[  119.461308][    T1] hub 2-0:1.0: 8 ports detected
[  119.462113][    T1] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[  119.464038][    T1] serio: i8042 KBD port at 0x60,0x64 irq 1
[  119.464845][    T1] serio: i8042 AUX port at 0x60,0x64 irq 12
[  119.465796][    T1] rtc_cmos 00:05: RTC can wake from S4
[  119.467194][   T67] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[  119.468717][    T1] rtc_cmos 00:05: registered as rtc0
[  119.469499][    T1] rtc_cmos 00:05: setting system clock to 2023-08-18T16:29:43 UTC (1692376183)
[  119.470804][    T1] rtc_cmos 00:05: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
[  119.471979][    T1] i2c_dev: i2c /dev entries driver
[  119.472765][    T1] piix4_smbus 0000:00:01.3: SMBus Host Controller at 0x700, revision 0
[  119.473986][    T1] Driver for 1-wire Dallas network protocol.
[  119.516268][    T1] intel_powerclamp: CPU does not support MWAIT
[  119.517709][    T1] iTCO_vendor_support: vendor-support=0
[  119.519000][    T1] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
[  119.521040][    T1] softdog:              soft_reboot_cmd=<not set> soft_active_on_boot=0
[  119.523015][    T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[  119.525155][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[  119.526914][    T1] ccp_crypto: Cannot load: there are no available CCPs
[  119.528465][    T1] usbcore: registered new interface driver usbhid
[  119.529858][    T1] usbhid: USB HID core driver
[  119.530918][    T1] amd_hsmp: HSMP is not supported on Family:6 model:56
[  119.532450][    T1] dell_smbios: Unable to run on non-system
[  119.533866][    T1] pktgen: Packet Generator for packet performance testing. Version: 2.75
[  119.535134][    T1] GACT probability NOT on
[  119.535746][    T1] Mirror/redirect action on
[  119.536385][    T1] netem: version 1.3
[  119.536947][    T1] u32 classifier
[  119.537441][    T1]     Performance counters on
[  119.538095][    T1]     input device check on
[  119.538724][    T1]     Actions configured
[  119.557885][    T1] xt_time: kernel timezone is -0000
[  119.558628][    T1] IPVS: Registered protocols (TCP, UDP)
[  119.559419][    T1] IPVS: Connection hash table configured (size=262144, memory=2048Kbytes)
[  119.560939][    T1] IPVS: ipvs loaded.
[  119.561480][    T1] IPVS: [rr] scheduler registered.
[  119.562192][    T1] IPVS: [wrr] scheduler registered.
[  119.562922][    T1] IPVS: [lc] scheduler registered.
[  119.563633][    T1] IPVS: [wlc] scheduler registered.
[  119.564364][    T1] IPVS: [fo] scheduler registered.
[  119.565086][    T1] IPVS: [lblc] scheduler registered.
[  119.565832][    T1] IPVS: [lblcr] scheduler registered.
[  119.566579][    T1] IPVS: [dh] scheduler registered.
[  119.567287][    T1] IPVS: [sh] scheduler registered.
[  119.568001][    T1] IPVS: [sed] scheduler registered.
[  119.568727][    T1] IPVS: [nq] scheduler registered.
[  119.569479][    T1] ipip: IPv4 and MPLS over IPv4 tunneling driver
[  119.570511][    T1] gre: GRE over IPv4 demultiplexor driver
[  119.571322][    T1] ip_gre: GRE over IPv4 tunneling driver
[  119.572389][    T1] Initializing XFRM netlink socket
[  119.573154][    T1] NET: Registered PF_INET6 protocol family
[  119.574313][    T1] Segment Routing with IPv6
[  119.574957][    T1] In-situ OAM (IOAM) with IPv6
[  119.575645][    T1] mip6: Mobile IPv6
[  119.576218][    T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[  119.577381][    T1] ip6_gre: GRE over IPv6 tunneling driver
[  119.578302][    T1] NET: Registered PF_PACKET protocol family
[  119.579135][    T1] NET: Registered PF_KEY protocol family
[  119.579950][    T1] Bridge firewalling registered
[  119.580709][    T1] NET: Registered PF_KCM protocol family
[  119.581505][    T1] 8021q: 802.1Q VLAN Support v1.8
[  119.582237][    T1] Key type dns_resolver registered
[  119.582950][    T1] openvswitch: Open vSwitch switching datapath
[  119.583850][    T1] mpls_gso: MPLS GSO support
[  119.584765][    T1] IPI shorthand broadcast: enabled
[  119.585472][    T1] AVX2 version of gcm_enc/dec engaged.
[  119.586272][    T1] AES CTR mode by8 optimization enabled
[  119.590505][    T1] sched_clock: Marking stable (119462002463, 127853924)->(119657719680, -67863293)
[  119.591880][    T1] registered taskstats version 1
[  119.593024][    T1] Loading compiled-in X.509 certificates


[  152.717909][   T65] sas: Enter sas_scsi_recover_host busy: 6 failed: 6
[  152.718921][   T65] sas: trying to find task 0x00000000f6998a3b
[  152.719717][   T65] sas: sas_scsi_find_task: aborting task 0x00000000f6998a3b
[  152.720777][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 694
[  152.724977][   T65] sas: sas_scsi_find_task: task 0x00000000f6998a3b is aborted
[  152.725956][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000f6998a3b is aborted
[  152.726982][   T65] sas: trying to find task 0x00000000b320eaa4
[  152.727762][   T65] sas: sas_scsi_find_task: aborting task 0x00000000b320eaa4
[  152.728784][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 667
[  152.731867][   T65] sas: sas_scsi_find_task: task 0x00000000b320eaa4 is aborted
[  152.732813][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000b320eaa4 is aborted
[  152.733832][   T65] sas: trying to find task 0x00000000a0e07144
[  152.734611][   T65] sas: sas_scsi_find_task: aborting task 0x00000000a0e07144
[  152.736298][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 692
[  152.738586][   T65] sas: sas_scsi_find_task: task 0x00000000a0e07144 is aborted
[  152.739553][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000a0e07144 is aborted
[  152.740591][   T65] sas: trying to find task 0x00000000f261e82a
[  152.741399][   T65] sas: sas_scsi_find_task: aborting task 0x00000000f261e82a
[  152.742397][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 682
[  152.744904][   T65] sas: sas_scsi_find_task: task 0x00000000f261e82a is aborted
[  152.745849][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000f261e82a is aborted
[  152.746875][   T65] sas: trying to find task 0x00000000a0d0a7fd
[  152.747644][   T65] sas: sas_scsi_find_task: aborting task 0x00000000a0d0a7fd
[  152.748645][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 666
[  152.753894][   T65] sas: sas_scsi_find_task: task 0x00000000a0d0a7fd is aborted
[  152.754845][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000a0d0a7fd is aborted
[  152.755850][   T65] sas: trying to find task 0x0000000002d18eb4
[  152.756675][   T65] sas: sas_scsi_find_task: aborting task 0x0000000002d18eb4
[  152.757742][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 659
[  152.763597][   T65] sas: sas_scsi_find_task: task 0x0000000002d18eb4 is aborted
[  152.764557][   T65] sas: sas_eh_handle_sas_errors: task 0x0000000002d18eb4 is aborted
[  152.765560][   T65] sas: ata6: end_device-0:0:13: cmd error handler
[  152.766390][   T65] sas: ata5: end_device-0:0:10: cmd error handler
[  152.767198][   T65] sas: ata8: end_device-0:0:16: cmd error handler
[  152.768005][   T65] sas: ata7: end_device-0:0:15: cmd error handler
[  152.768808][   T65] sas: ata1: end_device-0:0:0: cmd error handler
[  152.769602][   T65] sas: ata3: end_device-0:0:5: cmd error handler
[  152.770425][   T75] sas: ata1: end_device-0:0:0: dev error handler
[  152.771256][   T75] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  152.772264][   T75] ata1.00: failed command: READ SECTOR(S)
[  152.772997][   T75] ata1.00: cmd 20/00:01:00:01:20/00:00:00:00:00/e0 tag 0 pio 4096 in
[  152.772997][   T75]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  152.775019][   T75] ata1.00: status: { DRDY }
[  152.775594][   T75] ata1: hard resetting link
[  152.776197][   T73] sas: ata2: end_device-0:0:2: dev error handler
[  152.777033][   T73] sas: ata3: end_device-0:0:5: dev error handler
[  152.777831][   T73] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  152.778820][   T73] ata3.00: failed command: READ SECTOR(S) EXT
[  152.779589][   T73] ata3.00: cmd 24/00:01:8e:ff:87/00:00:91:00:00/e0 tag 0 pio 4096 in
[  152.779589][   T73]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  152.781618][   T73] ata3.00: status: { DRDY }
[  152.782208][   T73] ata3: hard resetting link
[  152.782766][   T71] sas: ata4: end_device-0:0:8: dev error handler
[  152.783559][   T71] sas: ata5: end_device-0:0:10: dev error handler
[  152.784363][   T71] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  152.785364][   T71] ata5.00: failed command: READ SECTOR(S)
[  152.786078][   T71] ata5.00: cmd 20/00:01:0f:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  152.786078][   T71]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  152.788165][   T71] ata5.00: status: { DRDY }
[  152.788733][   T71] ata5: hard resetting link
[  152.789325][   T77] sas: ata6: end_device-0:0:13: dev error handler
[  152.790134][   T77] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  152.791126][   T77] ata6.00: failed command: READ SECTOR(S)
[  152.791849][   T77] ata6.00: cmd 20/00:01:00:04:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  152.791849][   T77]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  152.793861][   T77] ata6.00: status: { DRDY }
[  152.794419][   T77] ata6: hard resetting link
[  152.794998][   T78] sas: ata7: end_device-0:0:15: dev error handler
[  152.795789][   T78] ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  152.796776][   T78] ata7.00: failed command: READ SECTOR(S) EXT
[  152.797532][   T78] ata7.00: cmd 24/00:01:b6:ff:87/00:00:91:00:00/e0 tag 0 pio 4096 in
[  152.797532][   T78]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  152.799536][   T78] ata7.00: status: { DRDY }
[  152.800106][   T78] ata7: hard resetting link
[  152.800667][   T81] sas: ata8: end_device-0:0:16: dev error handler
[  152.801487][   T81] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  152.802462][   T81] ata8.00: failed command: READ SECTOR(S)
[  152.803172][   T81] ata8.00: cmd 20/00:1f:21:00:00/00:00:00:00:00/e0 tag 0 pio 126976 in
[  152.803172][   T81]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  152.805176][   T81] ata8.00: status: { DRDY }
[  152.805734][   T81] ata8: hard resetting link
[  152.806300][   T72] sas: ata9: end_device-0:0:18: dev error handler
[  152.807108][   T76] sas: broadcast received: 9
[  152.807700][   T80] sas: REVALIDATION DEFERRED on port 0, pid:80
[  152.808486][   T76] sas: broadcast received: 9
[  152.809074][   T76] sas: broadcast received: 9
[  152.820988][   T72] sas: broadcast received: 9
[  152.821576][   T72] sas: broadcast received: 9
[  152.822155][   T72] sas: broadcast received: 9
[  152.832402][   T72] sas: broadcast received: 9
[  152.833187][   T72] sas: broadcast received: 9
[  152.833750][   T72] sas: broadcast received: 9
[  152.865933][   T72] sas: broadcast received: 9
[  152.866611][   T72] sas: broadcast received: 9
[  152.867187][   T72] sas: broadcast received: 9
[  152.911096][   T72] sas: broadcast received: 9
[  152.911729][   T72] sas: broadcast received: 9
[  152.912376][   T72] sas: broadcast received: 9
[  152.923097][   T72] sas: broadcast received: 9
[  152.923715][   T72] sas: broadcast received: 9
[  152.924358][   T72] sas: broadcast received: 9
[  154.993293][   T75] ata1.00: configured for PIO4
[  154.994063][   T75] sd 0:0:0:0: [sda] tag#602 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  154.995415][   T75] sd 0:0:0:0: [sda] tag#602 Sense Key : Illegal Request [current] 
[  154.996447][   T75] sd 0:0:0:0: [sda] tag#602 Add. Sense: Unaligned write command
[  154.997448][   T75] sd 0:0:0:0: [sda] tag#602 CDB: Read(10) 28 00 00 20 01 00 00 00 01 00
[  154.998521][   T75] I/O error, dev sda, sector 16779264 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  154.999833][   T75] ata1: EH complete
[  155.001835][   T78] ata7.00: configured for PIO4
[  155.002476][   T78] sd 0:0:6:0: [sdg] tag#618 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  155.003799][   T78] sd 0:0:6:0: [sdg] tag#618 Sense Key : Illegal Request [current] 
[  155.004839][   T78] sd 0:0:6:0: [sdg] tag#618 Add. Sense: Unaligned write command
[  155.005834][   T78] sd 0:0:6:0: [sdg] tag#618 CDB: Read(10) 28 00 91 87 ff b6 00 00 01 00
[  155.006937][   T78] I/O error, dev sdg, sector 19532873136 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  155.008235][   T78] ata7: EH complete
[  155.065244][   T77] ata6.00: configured for PIO4
[  155.065880][   T77] sd 0:0:5:0: [sdf] tag#630 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  155.067171][   T77] sd 0:0:5:0: [sdf] tag#630 Sense Key : Illegal Request [current] 
[  155.068197][   T77] sd 0:0:5:0: [sdf] tag#630 Add. Sense: Unaligned write command
[  155.069234][   T77] sd 0:0:5:0: [sdf] tag#630 CDB: Read(10) 28 00 00 00 04 00 00 00 01 00
[  155.070325][   T77] I/O error, dev sdf, sector 8192 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  155.071589][   T77] ata6: EH complete
[  155.073169][   T71] ata5.00: configured for PIO4
[  155.073794][   T71] sd 0:0:4:0: [sde] tag#603 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  155.075061][   T71] sd 0:0:4:0: [sde] tag#603 Sense Key : Illegal Request [current] 
[  155.076065][   T71] sd 0:0:4:0: [sde] tag#603 Add. Sense: Unaligned write command
[  155.077044][   T71] sd 0:0:4:0: [sde] tag#603 CDB: Read(10) 28 00 00 00 00 0f 00 00 01 00
[  155.078132][   T71] I/O error, dev sde, sector 120 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  155.079394][   T71] ata5: EH complete
[  160.391906][   T73] ata3.00: qc timeout after 5000 msecs (cmd 0xec)
[  160.392868][   T81] ata8.00: qc timeout after 5000 msecs (cmd 0xec)
[  160.393708][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 1
[  160.394868][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 0
[  160.396135][   T73] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  160.397063][   T73] ata3.00: revalidation failed (errno=-5)
[  160.397804][   T73] ata3: hard resetting link
[  160.398512][   T81] ata8.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  160.399445][   T81] ata8.00: revalidation failed (errno=-5)
[  160.400229][   T81] ata8: hard resetting link
[  160.405206][   T71] sas: broadcast received: 9
[  160.405927][   T71] sas: broadcast received: 9
[  160.406519][   T71] sas: broadcast received: 9
[  160.482955][   T71] sas: broadcast received: 9
[  160.483643][   T71] sas: broadcast received: 9
[  160.484325][   T71] sas: broadcast received: 9
[  160.505781][   T71] sas: broadcast received: 9
[  160.506444][   T71] sas: broadcast received: 9
[  160.507286][   T71] sas: broadcast received: 9
[  162.617463][   T73] ata3.00: configured for PIO4
[  162.618253][   T73] sd 0:0:2:0: [sdc] tag#595 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=40s
[  162.619829][   T73] sd 0:0:2:0: [sdc] tag#595 Sense Key : Illegal Request [current] 
[  162.621030][   T73] sd 0:0:2:0: [sdc] tag#595 Add. Sense: Unaligned write command
[  162.622194][   T73] sd 0:0:2:0: [sdc] tag#595 CDB: Read(10) 28 00 91 87 ff 8e 00 00 01 00
[  162.623449][   T73] I/O error, dev sdc, sector 19532872816 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  162.625013][   T73] ata3: EH complete
[  162.626557][   T81] ata8.00: configured for PIO4
[  162.627332][   T81] sd 0:0:7:0: [sdh] tag#628 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=40s
[  162.628898][   T81] sd 0:0:7:0: [sdh] tag#628 Sense Key : Illegal Request [current] 
[  162.630079][   T81] sd 0:0:7:0: [sdh] tag#628 Add. Sense: Unaligned write command
[  162.631195][   T81] sd 0:0:7:0: [sdh] tag#628 CDB: Read(10) 28 00 00 00 00 21 00 00 1f 00
[  162.632430][   T81] I/O error, dev sdh, sector 264 op 0x0:(READ) flags 0x80700 phys_seg 27 prio class 2
[  162.633870][   T81] ata8: EH complete
[  162.635278][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 6 tries: 1
[  162.636710][   T71] sas: broadcast received: 9
[  162.637421][   T77] sas: REVALIDATING DOMAIN on port 0, pid:77
[  162.639059][   T77] sas: ex 500e004abbbbbb7f phy00 change count has changed
[  162.640510][   T77] sas: ex 500e004abbbbbb7f phy00 originated BROADCAST(CHANGE)
[  162.641592][   T77] sas: ex 500e004abbbbbb7f rediscovering phy00
[  162.643077][   T77] sas: ex 500e004abbbbbb7f phy00 broadcast flutter
[  162.644834][   T77] sas: ex 500e004abbbbbb7f phy05 originated BROADCAST(CHANGE)
[  162.645922][   T77] sas: ex 500e004abbbbbb7f rediscovering phy05
[  162.647493][   T77] sas: ex 500e004abbbbbb7f phy05 broadcast flutter
[  162.649478][   T77] sas: ex 500e004abbbbbb7f phy10 originated BROADCAST(CHANGE)
[  162.650559][   T77] sas: ex 500e004abbbbbb7f rediscovering phy10
[  162.652076][   T77] sas: ex 500e004abbbbbb7f phy10 broadcast flutter
[  162.653562][   T77] sas: ex 500e004abbbbbb7f phy13 originated BROADCAST(CHANGE)
[  162.654635][   T77] sas: ex 500e004abbbbbb7f rediscovering phy13
[  162.656435][   T77] sas: ex 500e004abbbbbb7f phy13 broadcast flutter
[  162.657772][   T77] sas: ex 500e004abbbbbb7f phy15 originated BROADCAST(CHANGE)
[  162.658896][   T77] sas: ex 500e004abbbbbb7f rediscovering phy15
[  162.660425][   T77] sas: ex 500e004abbbbbb7f phy15 broadcast flutter
[  162.661644][   T77] sas: ex 500e004abbbbbb7f phy16 originated BROADCAST(CHANGE)
[  162.662694][   T77] sas: ex 500e004abbbbbb7f rediscovering phy16
[  162.664149][   T77] sas: ex 500e004abbbbbb7f phy16 broadcast flutter
[  162.670302][   T77] sas: done REVALIDATING DOMAIN on port 0, pid:77, res 0x0
[  193.165896][   T65] sas: Enter sas_scsi_recover_host busy: 5 failed: 5
[  193.166729][   T65] sas: trying to find task 0x00000000b320eaa4
[  193.167402][   T65] sas: sas_scsi_find_task: aborting task 0x00000000b320eaa4
[  193.168259][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 684
[  193.169358][   T65] sas: sas_scsi_find_task: task 0x00000000b320eaa4 is aborted
[  193.170194][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000b320eaa4 is aborted
[  193.171053][   T65] sas: trying to find task 0x00000000f261e82a
[  193.171695][   T65] sas: sas_scsi_find_task: aborting task 0x00000000f261e82a
[  193.172545][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 692
[  193.173566][   T65] sas: sas_scsi_find_task: task 0x00000000f261e82a is aborted
[  193.174401][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000f261e82a is aborted
[  193.175257][   T65] sas: trying to find task 0x00000000a0e07144
[  193.175920][   T65] sas: sas_scsi_find_task: aborting task 0x00000000a0e07144
[  193.176771][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 645
[  193.177819][   T65] sas: sas_scsi_find_task: task 0x00000000a0e07144 is aborted
[  193.178641][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000a0e07144 is aborted
[  193.179513][   T65] sas: trying to find task 0x00000000f6998a3b
[  193.180164][   T65] sas: sas_scsi_find_task: aborting task 0x00000000f6998a3b
[  193.181011][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 689
[  193.182019][   T65] sas: sas_scsi_find_task: task 0x00000000f6998a3b is aborted
[  193.182818][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000f6998a3b is aborted
[  193.183664][   T65] sas: trying to find task 0x000000000397263e
[  193.184350][   T65] sas: sas_scsi_find_task: aborting task 0x000000000397263e
[  193.185279][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 690
[  193.186292][   T65] sas: sas_scsi_find_task: task 0x000000000397263e is aborted
[  193.187103][   T65] sas: sas_eh_handle_sas_errors: task 0x000000000397263e is aborted
[  193.187955][   T65] sas: ata1: end_device-0:0:0: cmd error handler
[  193.188634][   T65] sas: ata3: end_device-0:0:5: cmd error handler
[  193.189319][   T65] sas: ata5: end_device-0:0:10: cmd error handler
[  193.190006][   T65] sas: ata6: end_device-0:0:13: cmd error handler
[  193.190669][   T65] sas: ata8: end_device-0:0:16: cmd error handler
[  193.191503][   T77] sas: ata1: end_device-0:0:0: dev error handler
[  193.192192][   T77] ata1.00: limiting speed to UDMA/133:PIO3
[  193.192807][   T77] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  193.193634][   T77] ata1.00: failed command: READ SECTOR(S)
[  193.194244][   T77] ata1.00: cmd 20/00:01:10:38:20/00:00:00:00:00/e0 tag 0 pio 4096 in
[  193.194244][   T77]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  193.195940][   T77] ata1.00: status: { DRDY }
[  193.196420][   T77] ata1: hard resetting link
[  193.196931][   T71] sas: ata2: end_device-0:0:2: dev error handler
[  193.197616][   T71] sas: ata3: end_device-0:0:5: dev error handler
[  193.198282][   T71] ata3.00: limiting speed to UDMA/133:PIO3
[  193.198917][   T71] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  193.199738][   T71] ata3.00: failed command: READ SECTOR(S) EXT
[  193.200370][   T71] ata3.00: cmd 24/00:01:89:ff:87/00:00:91:00:00/e0 tag 0 pio 4096 in
[  193.200370][   T71]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  193.202027][   T71] ata3.00: status: { DRDY }
[  193.202491][   T71] ata3: hard resetting link
[  193.202972][   T73] sas: ata4: end_device-0:0:8: dev error handler
[  193.203744][   T73] sas: ata5: end_device-0:0:10: dev error handler
[  193.204417][   T73] ata5.00: limiting speed to UDMA/133:PIO3
[  193.205031][   T73] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  193.205855][   T73] ata5.00: failed command: READ SECTOR(S)
[  193.206455][   T73] ata5.00: cmd 20/00:0f:11:00:00/00:00:00:00:00/e0 tag 0 pio 61440 in
[  193.206455][   T73]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  193.208209][   T73] ata5.00: status: { DRDY }
[  193.208692][   T73] ata5: hard resetting link
[  193.209213][   T81] sas: ata6: end_device-0:0:13: dev error handler
[  193.209887][   T81] ata6.00: limiting speed to UDMA/133:PIO3
[  193.210486][   T81] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  193.211304][   T81] ata6.00: failed command: READ SECTOR(S)
[  193.211905][   T81] ata6.00: cmd 20/00:01:0f:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  193.211905][   T81]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  193.213551][   T81] ata6.00: status: { DRDY }
[  193.214028][   T81] ata6: hard resetting link
[  193.214498][   T78] sas: ata7: end_device-0:0:15: dev error handler
[  193.215166][   T78] sas: ata8: end_device-0:0:16: dev error handler
[  193.215831][   T78] ata8.00: limiting speed to UDMA/133:PIO3
[  193.216432][   T78] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  193.217253][   T78] ata8.00: failed command: READ SECTOR(S)
[  193.217842][   T78] ata8.00: cmd 20/00:01:25:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  193.217842][   T78]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  193.219505][   T78] ata8.00: status: { DRDY }
[  193.219978][   T78] ata8: hard resetting link
[  193.220440][   T75] sas: ata9: end_device-0:0:18: dev error handler
[  193.221102][   T75] sas: broadcast received: 9
[  193.221581][   T72] sas: REVALIDATION DEFERRED on port 0, pid:72
[  193.223031][   T75] sas: broadcast received: 9
[  193.223524][   T75] sas: broadcast received: 9
[  193.229957][   T75] sas: broadcast received: 9
[  193.230486][   T75] sas: broadcast received: 9
[  193.231042][   T75] sas: broadcast received: 9
[  193.298255][   T75] sas: broadcast received: 9
[  193.298816][   T75] sas: broadcast received: 9
[  193.299351][   T75] sas: broadcast received: 9
[  193.310301][   T75] sas: broadcast received: 9
[  193.310965][   T75] sas: broadcast received: 9
[  193.311406][   T75] sas: broadcast received: 9
[  193.322248][   T75] sas: broadcast received: 9
[  193.322754][   T75] sas: broadcast received: 9
[  193.323266][   T75] sas: broadcast received: 9
[  195.440964][   T81] ata6.00: configured for PIO3
[  195.441775][   T81] sd 0:0:5:0: [sdf] tag#625 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  195.443287][   T81] sd 0:0:5:0: [sdf] tag#625 Sense Key : Illegal Request [current] 
[  195.444490][   T81] sd 0:0:5:0: [sdf] tag#625 Add. Sense: Unaligned write command
[  195.445637][   T81] sd 0:0:5:0: [sdf] tag#625 CDB: Read(10) 28 00 00 00 00 0f 00 00 01 00
[  195.446883][   T81] I/O error, dev sdf, sector 120 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  195.448295][   T81] ata6: EH complete
[  195.450004][   T77] ata1.00: configured for PIO3
[  195.450753][   T77] sd 0:0:0:0: [sda] tag#620 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  195.452183][   T77] sd 0:0:0:0: [sda] tag#620 Sense Key : Illegal Request [current] 
[  195.453033][   T77] sd 0:0:0:0: [sda] tag#620 Add. Sense: Unaligned write command
[  195.453867][   T77] sd 0:0:0:0: [sda] tag#620 CDB: Read(10) 28 00 00 20 38 10 00 00 01 00
[  195.454750][   T77] I/O error, dev sda, sector 16892032 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  195.455819][   T77] ata1: EH complete
[  195.457155][   T73] ata5.00: configured for PIO3
[  195.457742][   T73] sd 0:0:4:0: [sde] tag#581 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  195.458827][   T73] sd 0:0:4:0: [sde] tag#581 Sense Key : Illegal Request [current] 
[  195.459670][   T73] sd 0:0:4:0: [sde] tag#581 Add. Sense: Unaligned write command
[  195.460534][   T73] sd 0:0:4:0: [sde] tag#581 CDB: Read(10) 28 00 00 00 00 11 00 00 0f 00
[  195.461422][   T73] I/O error, dev sde, sector 136 op 0x0:(READ) flags 0x80700 phys_seg 15 prio class 2
[  195.462448][   T73] ata5: EH complete
[  195.462950][   T78] ata8.00: configured for PIO3
[  195.463490][   T78] ata8: EH complete
[  200.839897][   T71] ata3.00: qc timeout after 5000 msecs (cmd 0x27)
[  200.840984][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 1
[  200.842408][   T71] ata3.00: failed to read native max address (err_mask=0x4)
[  200.843515][   T71] ata3.00: HPA support seems broken, skipping HPA handling
[  200.844597][   T71] ata3.00: revalidation failed (errno=-5)
[  200.845457][   T71] ata3: hard resetting link
[  200.848560][   T77] sas: broadcast received: 9
[  200.849332][   T77] sas: broadcast received: 9
[  200.850111][   T77] sas: broadcast received: 9
[  200.936955][   T77] sas: broadcast received: 9
[  200.937845][   T77] sas: broadcast received: 9
[  200.938616][   T77] sas: broadcast received: 9
[  203.064888][   T71] ata3.00: configured for PIO3
[  203.065688][   T71] sd 0:0:2:0: [sdc] tag#628 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=40s
[  203.067230][   T71] sd 0:0:2:0: [sdc] tag#628 Sense Key : Illegal Request [current] 
[  203.068418][   T71] sd 0:0:2:0: [sdc] tag#628 Add. Sense: Unaligned write command
[  203.069578][   T71] sd 0:0:2:0: [sdc] tag#628 CDB: Read(10) 28 00 91 87 ff 89 00 00 01 00
[  203.070839][   T71] I/O error, dev sdc, sector 19532872776 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  203.072365][   T71] ata3: EH complete
[  203.073871][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 5 tries: 1
[  203.075399][   T77] sas: broadcast received: 9
[  203.076124][   T73] sas: REVALIDATING DOMAIN on port 0, pid:73
[  203.077968][   T73] sas: ex 500e004abbbbbb7f phy00 change count has changed
[  203.079263][   T73] sas: ex 500e004abbbbbb7f phy00 originated BROADCAST(CHANGE)
[  203.080357][   T73] sas: ex 500e004abbbbbb7f rediscovering phy00
[  203.081705][   T73] sas: ex 500e004abbbbbb7f phy00 broadcast flutter
[  203.083576][   T73] sas: ex 500e004abbbbbb7f phy05 originated BROADCAST(CHANGE)
[  203.084786][   T73] sas: ex 500e004abbbbbb7f rediscovering phy05
[  203.086324][   T73] sas: ex 500e004abbbbbb7f phy05 broadcast flutter
[  203.088264][   T73] sas: ex 500e004abbbbbb7f phy10 originated BROADCAST(CHANGE)
[  203.089356][   T73] sas: ex 500e004abbbbbb7f rediscovering phy10
[  203.090830][   T73] sas: ex 500e004abbbbbb7f phy10 broadcast flutter
[  203.092400][   T73] sas: ex 500e004abbbbbb7f phy13 originated BROADCAST(CHANGE)
[  203.093486][   T73] sas: ex 500e004abbbbbb7f rediscovering phy13
[  203.095188][   T73] sas: ex 500e004abbbbbb7f phy13 broadcast flutter
[  203.096947][   T73] sas: ex 500e004abbbbbb7f phy16 originated BROADCAST(CHANGE)
[  203.098049][   T73] sas: ex 500e004abbbbbb7f rediscovering phy16
[  203.099839][   T73] sas: ex 500e004abbbbbb7f phy16 broadcast flutter
[  203.105555][   T73] sas: done REVALIDATING DOMAIN on port 0, pid:73, res 0x0
[  233.613920][   T65] sas: Enter sas_scsi_recover_host busy: 4 failed: 4
[  233.615260][   T65] sas: trying to find task 0x00000000a0e07144
[  233.616203][   T65] sas: sas_scsi_find_task: aborting task 0x00000000a0e07144
[  233.617402][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 641
[  233.618898][   T65] sas: sas_scsi_find_task: task 0x00000000a0e07144 is aborted
[  233.620038][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000a0e07144 is aborted
[  233.621260][   T65] sas: trying to find task 0x00000000f6998a3b
[  233.622185][   T65] sas: sas_scsi_find_task: aborting task 0x00000000f6998a3b
[  233.623386][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 661
[  233.624817][   T65] sas: sas_scsi_find_task: task 0x00000000f6998a3b is aborted
[  233.625948][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000f6998a3b is aborted
[  233.627171][   T65] sas: trying to find task 0x0000000002d18eb4
[  233.628079][   T65] sas: sas_scsi_find_task: aborting task 0x0000000002d18eb4
[  233.629241][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 688
[  233.630622][   T65] sas: sas_scsi_find_task: task 0x0000000002d18eb4 is aborted
[  233.631745][   T65] sas: sas_eh_handle_sas_errors: task 0x0000000002d18eb4 is aborted
[  233.632982][   T65] sas: trying to find task 0x00000000b320eaa4
[  233.633921][   T65] sas: sas_scsi_find_task: aborting task 0x00000000b320eaa4
[  233.635083][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 674
[  233.636457][   T65] sas: sas_scsi_find_task: task 0x00000000b320eaa4 is aborted
[  233.637574][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000b320eaa4 is aborted
[  233.638744][   T65] sas: ata5: end_device-0:0:10: cmd error handler
[  233.639675][   T65] sas: ata8: end_device-0:0:16: cmd error handler
[  233.640616][   T65] sas: ata6: end_device-0:0:13: cmd error handler
[  233.641548][   T65] sas: ata3: end_device-0:0:5: cmd error handler
[  233.642675][   T77] sas: ata1: end_device-0:0:0: dev error handler
[  233.643622][   T77] sas: ata2: end_device-0:0:2: dev error handler
[  233.644563][   T73] sas: ata3: end_device-0:0:5: dev error handler
[  233.645490][   T73] ata3.00: limiting speed to PIO0
[  233.646231][   T73] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  233.647388][   T73] ata3.00: failed command: READ SECTOR(S)
[  233.648214][   T73] ata3.00: cmd 20/00:01:20:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  233.648214][   T73]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  233.650505][   T73] ata3.00: status: { DRDY }
[  233.651163][   T73] ata3: hard resetting link
[  233.651929][   T71] sas: ata4: end_device-0:0:8: dev error handler
[  233.652875][   T78] sas: ata5: end_device-0:0:10: dev error handler
[  233.653796][   T78] ata5.00: limiting speed to PIO0
[  233.654517][   T81] sas: ata6: end_device-0:0:13: dev error handler
[  233.655447][   T81] ata6.00: limiting speed to PIO0
[  233.656234][   T81] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  233.657409][   T81] ata6.00: failed command: READ SECTOR(S)
[  233.658232][   T81] ata6.00: cmd 20/00:01:00:01:20/00:00:00:00:00/e0 tag 0 pio 4096 in
[  233.658232][   T81]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  233.660492][   T81] ata6.00: status: { DRDY }
[  233.661146][   T81] ata6: hard resetting link
[  233.661791][   T75] sas: ata7: end_device-0:0:15: dev error handler
[  233.662707][   T72] sas: ata8: end_device-0:0:16: dev error handler
[  233.663609][   T72] ata8.00: limiting speed to PIO0
[  233.664316][   T72] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  233.665433][   T72] ata8.00: failed command: READ SECTOR(S)
[  233.666242][   T72] ata8.00: cmd 20/00:01:2d:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  233.666242][   T72]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  233.668493][   T72] ata8.00: status: { DRDY }
[  233.669139][   T72] ata8: hard resetting link
[  233.669779][   T76] sas: ata9: end_device-0:0:18: dev error handler
[  233.670758][   T80] sas: broadcast received: 9
[  233.671484][   T25] sas: REVALIDATION DEFERRED on port 0, pid:25
[  233.672962][   T80] sas: broadcast received: 9
[  233.673604][   T80] sas: broadcast received: 9
[  233.678755][   T80] sas: broadcast received: 9
[  233.679459][   T80] sas: broadcast received: 9
[  233.680230][   T80] sas: broadcast received: 9
[  233.745691][   T80] sas: broadcast received: 9
[  233.746307][   T80] sas: broadcast received: 9
[  233.746768][   T80] sas: broadcast received: 9
[  233.768707][   T80] sas: broadcast received: 9
[  233.769229][   T80] sas: broadcast received: 9
[  233.769674][   T80] sas: broadcast received: 9
[  235.896812][   T81] ata6.00: configured for PIO0
[  235.897606][   T81] sd 0:0:5:0: [sdf] tag#624 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  235.899194][   T81] sd 0:0:5:0: [sdf] tag#624 Sense Key : Illegal Request [current] 
[  235.900385][   T81] sd 0:0:5:0: [sdf] tag#624 Add. Sense: Unaligned write command
[  235.901552][   T81] sd 0:0:5:0: [sdf] tag#624 CDB: Read(10) 28 00 00 20 01 00 00 00 01 00
[  235.902815][   T81] I/O error, dev sdf, sector 16779264 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  235.904306][   T81] ata6: EH complete
[  235.906121][   T73] ata3.00: configured for PIO0
[  235.906916][   T73] sd 0:0:2:0: [sdc] tag#610 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  235.908424][   T73] sd 0:0:2:0: [sdc] tag#610 Sense Key : Illegal Request [current] 
[  235.909623][   T73] sd 0:0:2:0: [sdc] tag#610 Add. Sense: Unaligned write command
[  235.910767][   T73] sd 0:0:2:0: [sdc] tag#610 CDB: Read(10) 28 00 00 00 00 20 00 00 01 00
[  235.912004][   T73] I/O error, dev sdc, sector 256 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  235.913409][   T73] ata3: EH complete
[  235.914718][   T78] ata5.00: configured for PIO0
[  235.916367][   T72] ata8.00: configured for PIO0
[  235.917121][   T72] ata8: EH complete
[  235.917676][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 4 tries: 1
[  235.920140][   T78] sas: broadcast received: 9
[  235.921903][   T72] sas: REVALIDATING DOMAIN on port 0, pid:72
[  235.924586][   T72] sas: ex 500e004abbbbbb7f phy05 change count has changed
[  235.926812][   T72] sas: ex 500e004abbbbbb7f phy05 originated BROADCAST(CHANGE)
[  235.927908][   T72] sas: ex 500e004abbbbbb7f rediscovering phy05
[  235.929414][   T72] sas: ex 500e004abbbbbb7f phy05 broadcast flutter
[  235.931256][   T72] sas: ex 500e004abbbbbb7f phy10 originated BROADCAST(CHANGE)
[  235.932333][   T72] sas: ex 500e004abbbbbb7f rediscovering phy10
[  235.933760][   T72] sas: ex 500e004abbbbbb7f phy10 broadcast flutter
[  235.935410][   T72] sas: ex 500e004abbbbbb7f phy13 originated BROADCAST(CHANGE)
[  235.936491][   T72] sas: ex 500e004abbbbbb7f rediscovering phy13
[  235.938114][   T72] sas: ex 500e004abbbbbb7f phy13 broadcast flutter
[  235.939837][   T72] sas: ex 500e004abbbbbb7f phy16 originated BROADCAST(CHANGE)
[  235.940887][   T72] sas: ex 500e004abbbbbb7f rediscovering phy16
[  235.942599][   T72] sas: ex 500e004abbbbbb7f phy16 broadcast flutter
[  235.947681][   T72] sas: done REVALIDATING DOMAIN on port 0, pid:72, res 0x0
[  266.381892][   T65] sas: Enter sas_scsi_recover_host busy: 3 failed: 3
[  266.382971][   T65] sas: trying to find task 0x0000000002d18eb4
[  266.383750][   T65] sas: sas_scsi_find_task: aborting task 0x0000000002d18eb4
[  266.384764][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 651
[  266.386022][   T65] sas: sas_scsi_find_task: task 0x0000000002d18eb4 is aborted
[  266.387003][   T65] sas: sas_eh_handle_sas_errors: task 0x0000000002d18eb4 is aborted
[  266.388015][   T65] sas: trying to find task 0x00000000a0e07144
[  266.388795][   T65] sas: sas_scsi_find_task: aborting task 0x00000000a0e07144
[  266.389807][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 671
[  266.391024][   T65] sas: sas_scsi_find_task: task 0x00000000a0e07144 is aborted
[  266.391982][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000a0e07144 is aborted
[  266.392990][   T65] sas: trying to find task 0x00000000b320eaa4
[  266.393763][   T65] sas: sas_scsi_find_task: aborting task 0x00000000b320eaa4
[  266.394736][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 678
[  266.395918][   T65] sas: sas_scsi_find_task: task 0x00000000b320eaa4 is aborted
[  266.396854][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000b320eaa4 is aborted
[  266.397907][   T65] sas: ata5: end_device-0:0:10: cmd error handler
[  266.398748][   T65] sas: ata8: end_device-0:0:16: cmd error handler
[  266.399529][   T65] sas: ata3: end_device-0:0:5: cmd error handler
[  266.400458][   T78] sas: ata1: end_device-0:0:0: dev error handler
[  266.401285][   T78] sas: ata2: end_device-0:0:2: dev error handler
[  266.402083][   T72] sas: ata3: end_device-0:0:5: dev error handler
[  266.402877][   T72] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  266.403879][   T72] ata3.00: failed command: READ SECTOR(S) EXT
[  266.404634][   T72] ata3.00: cmd 24/00:01:df:fe:87/00:00:91:00:00/e0 tag 0 pio 4096 in
[  266.404634][   T72]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  266.406640][   T72] ata3.00: status: { DRDY }
[  266.407227][   T72] ata3: hard resetting link
[  266.407811][   T73] sas: ata4: end_device-0:0:8: dev error handler
[  266.408631][   T81] sas: ata5: end_device-0:0:10: dev error handler
[  266.409442][   T81] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  266.410446][   T81] ata5.00: failed command: READ SECTOR(S)
[  266.411220][   T81] ata5.00: cmd 20/00:01:13:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  266.411220][   T81]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  266.413238][   T81] ata5.00: status: { DRDY }
[  266.413825][   T81] ata5: hard resetting link
[  266.414386][   T80] sas: ata6: end_device-0:0:13: dev error handler
[  266.415197][   T77] sas: ata7: end_device-0:0:15: dev error handler
[  266.416008][   T75] sas: ata8: end_device-0:0:16: dev error handler
[  266.416818][   T75] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  266.417798][   T75] ata8.00: failed command: READ SECTOR(S)
[  266.418506][   T75] ata8.00: cmd 20/00:01:2d:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  266.418506][   T75]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  266.420468][   T75] ata8.00: status: { DRDY }
[  266.421047][   T75] ata8: hard resetting link
[  266.421602][   T76] sas: ata9: end_device-0:0:18: dev error handler
[  266.422416][   T71] sas: broadcast received: 9
[  266.422999][   T25] sas: REVALIDATION DEFERRED on port 0, pid:25
[  266.424282][   T71] sas: broadcast received: 9
[  266.424877][   T71] sas: broadcast received: 9
[  266.433735][   T78] sas: broadcast received: 9
[  266.434538][   T78] sas: broadcast received: 9
[  266.435186][   T78] sas: broadcast received: 9
[  266.489792][   T78] sas: broadcast received: 9
[  266.490430][   T78] sas: broadcast received: 9
[  266.491091][   T78] sas: broadcast received: 9
[  266.523637][   T78] sas: broadcast received: 9
[  266.524312][   T78] sas: broadcast received: 9
[  266.525019][   T78] sas: broadcast received: 9
[  268.665323][   T72] ata3.00: configured for PIO0
[  268.665976][   T72] sd 0:0:2:0: [sdc] tag#614 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=32s
[  268.667262][   T72] sd 0:0:2:0: [sdc] tag#614 Sense Key : Illegal Request [current] 
[  268.668276][   T72] sd 0:0:2:0: [sdc] tag#614 Add. Sense: Unaligned write command
[  268.669248][   T72] sd 0:0:2:0: [sdc] tag#614 CDB: Read(10) 28 00 91 87 fe df 00 00 01 00
[  268.670300][   T72] I/O error, dev sdc, sector 19532871416 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[  268.671616][   T72] ata3: EH complete
[  268.673229][   T75] ata8.00: configured for PIO0
[  268.673879][   T75] ata8: EH complete
[  283.783902][   T81] ata5.00: qc timeout after 15000 msecs (cmd 0xef)
[  283.785304][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 2
[  283.786729][   T81] ata5.00: failed to set xfermode (err_mask=0x4)
[  283.787708][   T81] ata5: hard resetting link
[  283.794706][   T72] sas: broadcast received: 9
[  283.795485][   T72] sas: broadcast received: 9
[  283.796202][   T72] sas: broadcast received: 9
[  283.883639][   T72] sas: broadcast received: 9
[  283.884635][   T72] sas: broadcast received: 9
[  283.885461][   T72] sas: broadcast received: 9
[  286.001568][   T81] ata5.00: configured for PIO0
[  286.002456][   T81] ata5: EH complete
[  286.002898][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 3 tries: 1
[  286.004055][   T72] sas: broadcast received: 9
[  286.004575][   T75] sas: REVALIDATING DOMAIN on port 0, pid:75
[  286.007002][   T75] sas: ex 500e004abbbbbb7f phy05 change count has changed
[  286.009087][   T75] sas: ex 500e004abbbbbb7f phy05 originated BROADCAST(CHANGE)
[  286.009907][   T75] sas: ex 500e004abbbbbb7f rediscovering phy05
[  286.011256][   T75] sas: ex 500e004abbbbbb7f phy05 broadcast flutter
[  286.012852][   T75] sas: ex 500e004abbbbbb7f phy10 originated BROADCAST(CHANGE)
[  286.013675][   T75] sas: ex 500e004abbbbbb7f rediscovering phy10
[  286.014824][   T75] sas: ex 500e004abbbbbb7f phy10 broadcast flutter
[  286.016594][   T75] sas: ex 500e004abbbbbb7f phy16 originated BROADCAST(CHANGE)
[  286.017446][   T75] sas: ex 500e004abbbbbb7f rediscovering phy16
[  286.018688][   T75] sas: ex 500e004abbbbbb7f phy16 broadcast flutter
[  286.024826][   T75] sas: done REVALIDATING DOMAIN on port 0, pid:75, res 0x0
[  316.045893][   T65] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[  316.046635][   T65] sas: trying to find task 0x00000000a0e07144
[  316.047511][   T65] sas: sas_scsi_find_task: aborting task 0x00000000a0e07144
[  316.048472][    C0] pm80xx0:: mpi_sata_completion 2293: task null, freeing CCB tag 669
[  316.049522][   T65] sas: sas_scsi_find_task: task 0x00000000a0e07144 is aborted
[  316.050365][   T65] sas: sas_eh_handle_sas_errors: task 0x00000000a0e07144 is aborted
[  316.051248][   T65] sas: ata8: end_device-0:0:16: cmd error handler
[  316.051987][   T72] sas: ata1: end_device-0:0:0: dev error handler
[  316.052700][   T72] sas: ata2: end_device-0:0:2: dev error handler
[  316.053415][   T75] sas: ata3: end_device-0:0:5: dev error handler
[  316.054120][   T75] sas: ata4: end_device-0:0:8: dev error handler
[  316.054895][   T81] sas: ata5: end_device-0:0:10: dev error handler
[  316.055586][   T81] sas: ata6: end_device-0:0:13: dev error handler
[  316.056303][   T78] sas: ata7: end_device-0:0:15: dev error handler
[  316.057006][   T78] sas: ata8: end_device-0:0:16: dev error handler
[  316.057689][   T78] ata8.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[  316.058546][   T78] ata8.00: failed command: READ SECTOR(S)
[  316.059187][   T78] ata8.00: cmd 20/00:01:31:00:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[  316.059187][   T78]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  316.060895][   T78] ata8.00: status: { DRDY }
[  316.061384][   T78] ata8: hard resetting link
[  316.061897][   T73] sas: ata9: end_device-0:0:18: dev error handler
[  316.066551][   T75] sas: broadcast received: 9
[  316.067293][   T72] sas: REVALIDATION DEFERRED on port 0, pid:72
[  316.068034][   T75] sas: broadcast received: 9
[  316.068538][   T75] sas: broadcast received: 9
[  316.155520][   T75] sas: broadcast received: 9
[  316.156512][   T75] sas: broadcast received: 9
[  316.157379][   T75] sas: broadcast received: 9
[  318.257551][   T78] ata8.00: configured for PIO0
[  318.258622][   T78] ata8: EH complete
[  318.259389][   T65] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 1 tries: 1
[  318.260688][   T75] sas: broadcast received: 9
[  318.261515][   T72] sas: REVALIDATING DOMAIN on port 0, pid:72
[  318.265927][   T72] sas: ex 500e004abbbbbb7f phy16 change count has changed
[  318.270095][   T72] sas: ex 500e004abbbbbb7f phy16 originated BROADCAST(CHANGE)
[  318.271226][   T72] sas: ex 500e004abbbbbb7f rediscovering phy16
[  318.272944][   T72] sas: ex 500e004abbbbbb7f phy16 broadcast flutter
[  318.286458][   T72] sas: done REVALIDATING DOMAIN on port 0, pid:72, res 0x0