Klipper Ender 5 Plus stock printer config

printer.cfg

# This file contains pin mappings for the Creality Ender 5 Plus.
# Ender 5 Plus stock uses a Creality v2.2 board, similar to CR-20 Pro.
# To use this config, the firmware should be compiled for the AVR atmega2560.

# See the example.cfg file for a description of available parameters.

[stepper_x]
step_pin: PF0
dir_pin: PF1
enable_pin: !PD7
step_distance: .0125
endstop_pin: ^PE5
position_endstop: 350
position_max: 350
homing_speed: 100

[stepper_y]
step_pin: PF6
dir_pin: PF7
enable_pin: !PF2
step_distance: .0125
endstop_pin: ^PJ1
position_endstop: 350
position_max: 350
homing_speed: 100

[stepper_z]
step_pin: PL3
dir_pin: PL1
enable_pin: !PK0
step_distance: .001266
#step_distance: .0025
endstop_pin: probe:z_virtual_endstop
position_max: 400
position_min: -5 #set position_min to a negative value such as -5 when probing to set z offset, then revert to 0
homing_speed: 10.0

[extruder]
step_pin: PA4
dir_pin: PA6
enable_pin: !PA2
step_distance: .010526
nozzle_diameter: 0.400
filament_diameter: 1.750
#pressure_advance: 0.617 # high value for stock long bowden tube, uncomment to enable pressure advance
#pressure_advance_smooth_time: 0.010 # uncomment to enable pressure advance
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK5
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 260

[safe_z_home]
home_xy_position: 180, 180
speed: 100
z_hop: 10 # Move up 10mm, so the probe doesnt hit anything 
z_hop_speed: 5

[bltouch]
sensor_pin: ^PD3
control_pin: PB5
x_offset: -45
y_offset: 0
#z_offset: 0
speed: 3.0
samples: 1
pin_up_reports_not_triggered: True
pin_up_touch_mode_reports_triggered: False

[bed_mesh]
speed: 100
horizontal_move_z: 8
mesh_min: 50, 50
mesh_max: 300,300
probe_count: 3,3 # 3,3 or 5,5
  
[gcode_macro G29]
gcode: 
  G28
  BED_MESH_CALIBRATE
  BED_MESH_PROFILE SAVE=p1
  G1 X0 Y0 Z5 F4000
  
[heater_bed]
heater_pin: PH5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PK6
control: pid
pid_Kp: 690.34
pid_Ki: 111.47
pid_Kd: 1068.83
min_temp: 0
max_temp: 130

[fan]
pin: PH6

[mcu]
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000 # 20x print speed recommended
max_z_velocity: 5
max_z_accel: 100

#[display]
# Not sure this is supported for E5+

I have mine set for 7200, but you should be able to set it higher. I haven't tested/checked this to see if Klipper has a limit that you need to override.

My Ender 5 Plus gives-me this error. I just installed and compiled Klipper.

Help appreciated...

Recv: // This type of error is frequently caused by running an older
Recv: // version of the firmware on the micro-controller (fix by
Recv: // recompiling and flashing the firmware).
Recv: // Once the underlying issue is corrected, use the "RESTART"
Recv: // command to reload the config and restart the host software.
Recv: // Protocol error connecting to printer
Recv: // Klipper state: Not ready

BTT TFT35.

[display]
lcd_type: emulated_st7920
spi_software_miso_pin: EXP2_1 #PB3
spi_software_mosi_pin: EXP1_3 #PH0
spi_software_sclk_pin: EXP1_5 #PA1
en_pin: EXP1_4 #PH1
encoder_pins: ^EXP2_5, ^EXP2_3 #PC4, PC6
click_pin: ^!EXP1_2 #PC2

[output_pin beeper]
pin: EXP1_1 #PG0

[board_pins]
aliases:
# EXP1 header
EXP1_1=PG0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=,
EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
# EXP 2 header
EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=,
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=, EXP2_10=PG0

How did you find the pinout? I am trying to find the pin names for the Creality v2.1 board.

If you mean pinout for lcd, it should be same.

How did you find the pinout? I am trying to find the pin names for the Creality v2.1 board.

I think you asked on Reddit too?
I used a multimeter to read the resistance on the board pins and processor.

Other wat is to peak in marlin pin config files.
Pin/ramps.h

is anybody know the second heater pin no as heater pin 1 is PB4 ?

Got the stock filament sensor working. I used a multimeter to find the MCU pin name and played around with some macros from other Githhub users.

Hi Bob that was a genius solution. Just curious, how did you trigger the pins to probe them w meter? Because now I'm not even using the factory board lol. Thanks

Got the stock filament sensor working. I used a multimeter to find the MCU pin name and played around with some macros from other Githhub users.

Hi Bob that was a genius solution. Just curious, how did you trigger the pins to probe them w meter? Because now I'm not even using the factory board lol. Thanks

I just found ones when they were powered off. I didn't need to find them all. So just a continuity check with multimeter.

hi guys i am trying to add a second part cooling fan but for the life of me i can't find the correct pin out i guessed at the number and added this to my printer.cfg but it didn't work any help would be great thanks.

multi_pin my_fan]
pins: PH6, PH7

[fan]
pin = multi_pin:my_fan

hi guys i am trying to add a second part cooling fan but for the life of me i can't find the correct pin out i guessed at the number and added this to my printer.cfg but it didn't work any help would be great thanks.

multi_pin my_fan] pins: PH6, PH7

[fan] pin = multi_pin:my_fan

What mainboard do you have?

hi guys i am trying to add a second part cooling fan but for the life of me i can't find the correct pin out i guessed at the number and added this to my printer.cfg but it didn't work any help would be great thanks.
multi_pin my_fan] pins: PH6, PH7
[fan] pin = multi_pin:my_fan

What mainboard do you have?

It's a creality silent board version 2.2

Hello I am trying to get Klipper running on my Ender 5 Plus. I'm stuck at flashing the hex onto the mainboard. I have the Creality silent board v2.2
When I put the sd card with the compiled hex file nothing happens. I tried changing the hex to a bin file. I have heard rumors that i need to unplug the screen, and others that i need to use Cura to flash the firmware over, but no one that's actually done it, just people that say they heard.

any help at all is greatly appreciated

[Edit:] The screen prevents flashing on the Ender 5's. I used the RPi to flash the firmware over